0% found this document useful (0 votes)
164 views2 pages

Mastertop 1700m 12-04

Uploaded by

djrote4
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
164 views2 pages

Mastertop 1700m 12-04

Uploaded by

djrote4
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

MASTERTOP® 1700M

A clear, water-based primer for use with MASTERTOP range of products

Description of Product Porous surfaces can be saturated with clean


MASTERTOP 1700M is a clear, water-based water, or an initial coat of
primer for use with MASTERTOP range of MASTERTOP 1700M can be applied and
products. allowed to dry to reduce suction of the
substrate.
MASTERTOP 1700M is a primer for MASTERTOP 1700M may be applied to
MASTERTOP 1710M, MASTERTOP 1730M, ”green” concrete, which has been given a
and MASTERTOP 1740M. light brush finish.
MASTERTOP 1700M can be applied on
Primary Uses damp substrates, but standing water should
MASTERTOP 1700M is used as a primer for be removed.
epoxy toppings.
Mixing:
Advantages Pour the base into the reactor component
• Easily mixed and applied and mix for 1 minute until the mixture is
• Can be applied to damp or green uniform and streak-free.
concrete Apply the mixed materials to the pre-soaked
• Improves chemical resistance substrate, with no standing water, at a rate of
6-8m2/ltr using a medium or short-haired
Packaging roller.
MASTERTOP 1700M is packed in 3.6kg Allow the primer to become tack-free prior to
units. over-coating with MASTERTOP 1710M or
MASTERTOP 1730M top layers.
Typical Properties If the substrate is porous and is not pre-
Working time: 30 minutes at 20oC saturated with water, two coats of the primer
Density: 1.02 to 1.12 at 25oC can be applied to reduce the suction of the
Maximum service -20OC to +60oC substrate.
temperature: When applying MASTERTOP 1740M as the
Water vapour 20,000 DIN 52615 top layer, the primer should be tacky at the
permeability: time the
MASTERTOP 1740M screed is laid. If the
Guide to Application primer dries before applying the
Primer coat: MASTERTOP 1740M, then apply a
Remove all surface laitance, oil, grease or subsequent layer of MASTERTOP 1700M
any defective concrete that will reduce the and proceed on the tacky surface.
bond of the flooring system. In all cases, it is best to put subsequent
A light etch giving the texture of fine sand layers immediately in the case of
paper is the ideal surface profile to apply MASTERTOP 1740M, and within 12 to 36
MASTERTOP 1700 series flooring systems. hours where the primer is recommended to
This can be achieved by captive blasting, dry.
light grit blasting or water jetting.
After the preparation is complete, ensure all Yield
dust is removed from the surface. 1ltr normally covers 6-8m2, but will vary
according to the porosity of the substrate.

Storage
MASTERTOP® 1700M

Store out of direct sunlight. In tropical


climates, the material should be stored in an
air-conditioned environment. Concrete,
screeds, renders, and blockwork should be
cured sufficiently after all shrinkage
movement has occured.

Shelf Life
Up to 12 months if stored in unopened
containers according to manufacturer’s
instructions.

Safety Precautions
As with all chemical products, care should be
taken, during use and storage, to avoid
contact with eyes, mouth, skin and foodstuffs
[which can also be tainted with vapor until
the product has fully cured or dried]. Treat
splashes to eyes and skin immediately. If
accidentally ingested seek medical attention
immediately. Re-seal containers after use.

Note
Field service, where provided, does not
constitute supervisory responsibility. For
additional information, contact your local
MBT representative.

MBT reserves the right to have the true


cause of any difficulty determined by
accepted test methods.

Quality Statement
All products manufactured by MBT Egypt, or
imported from MBT affiliate companies
world-wide, are manufactured to procedures
certified to conform to the quality
management systems described in the
ISO 9000 series.

12/04 MBT-EG

* Properties listed are only for guidance and are not a


guarantee of performance.

MBT, Egypt Tel.: +202 3453483/4 Whilst any information contained herein is true, accurate and
94 Shehab St. Mohandessin Fax: +202 3453481 Sales represents our best knowledge and experience, no warranty is given
Giza – Egypt Fax: +202 3453482 or implied with any recommendations made by us, our
Factory: Sadat City, Piece 118 Admin. representatives or distributors, as the conditions of use and the
Zone 4 Tel.: +2048 2604842 competence of any labour involved in the application are beyond our
Fax: +2048 2604757 control.
Certificate No. 158171
008

email: [email protected], website: www.mbt-egypt.com

As all MBT technical datasheets are updated on a regular basis, it is the user’s responsibility to obtain the most recent issue. Most recent issue is available on the website at
www.mbt-egypt.com

You might also like