TPower I45 Setup Ma nua l

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the

contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
 Table of Contents
Chapter 1: Introduction ............................................................ 1
1.1 Before You Start......................................................................................... 1
1.2 Package Checklist ..................................................................................... 1
1.3 Motherboard Features.............................................................................. 2
1.4 Rear Panel Connectors.............................................................................. 3
1.5 Motherboard Layout................................................................................. 4
Chapter 2: Hardware Installation ............................................. 5
2.1 Installing Central Processing Unit (CPU) ............................................... 5
2.2 FAN Headers.............................................................................................. 7
2.3 Installing System Memory ........................................................................ 8
2.4 Connectors and Slots................................................................................ 10
Chapter 3: Headers & Jumpers Setup ..................................... 13
3.1 How to Setup Jumpers............................................................................. 13
3.2 Detail Settings .......................................................................................... 13
Chapter 4: CrossFire Function................................................. 21
4.1 Requirements........................................................................................... 21
4.2 Installing CrossFire-Ready Graphics Cards.......................................... 21
Chapter 5: RAID Functions ..................................................... 23
5.1 Operation System .................................................................................... 23
5.2 Raid Arrays............................................................................................... 23
5.3 How RAID Works..................................................................................... 23
Chapter 6: T-Power BIOS & Software..................................... 27
6.1 T-Power BIOS ........................................................................................... 27
6.2 T-Power Software .................................................................................... 35
Chapter 7: Useful Help ............................................................ 45
7.1 Driver Installation Note.......................................................................... 45
7.2 Extra Information.................................................................................... 46
7.3 AMI BIOS Beep Code ............................................................................... 47
7.4 AMI BIOS Post Code................................................................................. 48
7.5 Troubleshooting ....................................................................................... 50
Appendencies: SPEC In Other Language ................................ 52
German.................................................................................................................. 52
France .................................................................................................................... 54
Italian..................................................................................................................... 56
Spanish ................................................................................................................... 58
Portuguese ............................................................................................................ 60
Polish...................................................................................................................... 62
Russian ................................................................................................................... 64
Arabic..................................................................................................................... 66
Japanese ................................................................................................................ 68
 TPower I45

CHAPTER 1: INTRODUCTION
1.1 BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„ Prepare a dry and stable working environment with
sufficient lighting.
„ Always disconnect the computer from power outlet
before operation.
„ Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
„ Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
„ Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
„ Keep the computer from dangerous area, such as heat
source, humid air and water.

1.2 PACKAGE CHECKLIST

HDD Cable X 1
Serial ATA Cable X 6
Serial ATA Power Cable X 6
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)

Note: The package contents may differ by area or your motherboard version.

1
Motherboard Manual

1.3 MOTHERBOARD FEATURES

SPEC

LGA 775
Supports Execute Disable Bit / Enhanced Intel
Intel Core2Duo / Core2Quad /
CPU SpeedStep® / Intel Architecture-64 / Extended
Pentium Dual-Core / Celeron Dual-Core /
Memory 64 Technology / Virtualization Technology
Celeron 4xx processor

FSB Support 800 / 1066 / 1333 / 1600 MHz

Intel P45
Chipset
Intel ICH10R

Fintek F71887F Environment Control initiatives,

Provides the most commonly used legacy Hardware Monitor Controller
Super I/O
Super I/O functionality. Fan Speed Controller
Low Pin Count Interface ITE's "Smart Guardian" function
DIMM Slots x 4
Dual Channel Mode DDR2 memory module
Main Each DIMM supports 256MB / 512MB /
Supports DDR2 1066 / 800 / 667
Memory 1GB / 2GB DDR2
Registered DIMM and ECC DIMM is not supported
Max Memory Capicity 8GB
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
IDE Marvell 88SE6121
supports PIO Mode 0~4
Data transfer rates up to 3 Gb/s.
SATA II ICH10R SATA Version 2.0 specification compliant.
RAID 0 / 1 / 5 / 1+0 support
Data transfer rates up to 3 Gb/s.
eSATA Marvell 88SE6121 SATA Version 2.0 specification compliant.
Port-Multiplier/RAID 0,1 support
10 / 100 Mb/s / 1Gb/s auto negotiation
LAN Realtek RTL 8111C
Half / Full duplex capability

Sound 7.1 channels audio out

ALC888S
Codec High Definition Audio
PCI slot x2 Supports PCI expansion cards
PCI Express Gen2 x16 slot (x16/x8) x1 Supports PCI-E Gen2 x16 expansion cards
Slots
PCI Express Gen2 x16 slot (x8) x1 Supports PCI-E Gen2 x16 expansion cards
PCI Express x1 slot x2 Supports PCI-E x1 expansion cards
On Board Floppy connector x1 Each connector supports 2 Floppy drives
Connector Serial port Connector x1 Connects to RS-232 Port
IDE Connector x1 Each connector supports 2 IDE device
SATA Connector x6 Each connector supports 1 SATA devices
Front Panel Connector x1 Supports front panel facilities

2
 TPower I45
SPEC

Front Audio Connector x1 Supports front panel audio function

CD-in Connector x1 Supports CD audio-in function

S/PDIF out connector x2 Supports digital audio out function
S/PDIF in connector x1 Supports digital audio-in function
CPU Fan header x1 CPU Fan power supply (with Smart Fan function)
System Fan header x2 System Fan Power supply
Clear CMOS header x1 Restore CMOS data to factory default
USB connector x3 Each connector supports 2 front panel USB ports
Power Connector (24pin) x1 Connects to Power supply
Power Connector (8pin) x1 Connects to Power supply
Power Connector (4pin) x1 Connects to Power supply

PS/2 Keyboard x1 Connects to PS/2 Keyboard

PS/2 Mouse x1 Connects to PS/2 Mouse
Back Panel LAN port x1 Connect to RJ-45 ethernet cable
I/O USB Port x6 Connect to USB devices
Audio Jack x6 Provide Audio-In/Out and microphone connection
eSATA Port x2 Connect to SATA devices
Board Size 244 (W) x 305 (L) mm ATX
Biostar Reserves the right to add or remove support for
OS Support Windows 2000 / XP / VISTA
any OS with or without notice

1.4 REAR PANEL CONNECTORS

PS/2 LAN
Mouse

PS/2 USBX2 USBX2 ESATAX2 USBX2

Keyboard

Center Line In

Rear Line Out

Side Mic In

3
Motherboard Manual
1.5 MOTHERBOARD LAYOUT
JKBMS1
JCFAN1
JATXPWR1

LGA775

CPU1
JUSB2

BIOS
JUSB1
ESATAX1

DDR2_A1

DDR2_A2

DDR2_B1

DDR2_B2
JUSBV1
JATXPWR2

JNFAN1
JRJ45USB1
Intel
P45
JAUDIO1
J1

PEX1_2

JCMOS1
LAN PEX16_1

JPE1 JPE3 JPE5 JPE7

SATA1
JSPDIF_OUT2

Intel
JCDIN1 PEX1_1
JPE2 JPE4 JPE6 JPE8
ICH10R SATA2

JPE9 BAT1

PEX16_2
SATA3
CODEC

PCI1
IDE
JSPDIF_OUT1 Super IDE1
I/O JUSBV2
PCI2 RSTSW2

JAUDIOF1 JCOM1 JUSB5 JUSB4 JUSB3 JPANEL1

FDD1 JSFAN1
PWRSW1
JSPDIF_IN1

Note: ■ represents the 1st pin.

4
 TPower I45
CHAPTER 2: HARDWARE INSTALLATION
2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)

Special Notice:
Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs won’t be damaged.

Pin Cap

Step 1: Pull the socket locking lever out from the socket and then raise
the lever up to a 90-degree angle.

5
Motherboard Manual
Step 2: Look for the triangular cut edge on socket, and the golden dot on
CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.
Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked
position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the JCFAN1. This completes the installation.

6
 TPower I45

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN1: CPU Fan Header

Pin Assignment
4 1 1 Ground
2 +12V
3 FAN RPM rate
sense
4 Smart Fan
Control

JNFAN1: NorthBridge Fan Header

JSFAN1: System Fan Header

Pin Assignment
JNFAN1
1 Ground
2 +12V
3 FAN RPM rate
sense

3 1

JSFAN1
Note:
The JNFAN1/JSFAN1 support 3-pin head connectors, and the JCFAN1 supports 4-pin
head connector. When connecting with wires onto connectors, please note that the red
wire is the positive and should be connected to pin#2, and the black wire is Ground and
should be connected to GND.

7
Motherboard Manual
2.3 INSTALLING SYSTEM MEMORY
A. Memory Modules

DD R2_A1
DD R2_A2

DD R2_B1
DD R2_B2
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

8
 TPower I45

B. Memory Capacity
DIMM Socket Total Memory
DDR2 Module
Location Size
DDR2_A1 256MB/512MB/1GB/2GB
DDR2_A2 256MB/512MB/1GB/2GB
Max is 8GB.
DDR2_B1 256MB/512MB/1GB/2GB
DDR2_B2 256MB/512MB/1GB/2GB

C. Dual Channel Memory installation

To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:

Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status DDR2_A1 DDR2_A2 DDR2_B1 DDR2_B2
Enabled O X O X
Enabled X O X O
Enabled O O O O
(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or
x16)

9
Motherboard Manual

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.

33 1

34 2

IDE1: IDE/ATAPI Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two devices.

39 1

40 2

10
 TPower I45

SATA1~SATA3: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 6 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

SATA3 SATA2 SATA1

PCI1/PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

11
Motherboard Manual

PEX16_1: PCI-Express Gen2 x16(x16/CrossFire x8 Speed) Slot

- PCI-Express 2.0 compliant.
- Maximum theoretical realized bandwidth of 8GB/s(4GB/s CrossFire)
simultaneously per direction, for an aggregate of 16GB/s(8GB/s CrossFire)
totally.
- PEX16_1 slot is reserved for graphics or video cards. The design of this
motherboard supports dual PCI-Express graphics cards using CrossFire
technology with multiple displays. When using CrossFire, this slot is master
and runs with x8 speed.
- To configure for CrossFire, please refer to the instructions of configuring
JPE1~JPE9.

PEX16_2: PCI-Express Gen2 x16(NC/CrossFire x8 Speed) Slot

- PCI-Express 2.0 compliant.
- Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
- PEX16_2 slot is reserved for graphics or video cards. The design of this
motherboard supports dual PCI-Express graphics cards using CrossFire
technology with multiple displays. This slot is slave when using CrossFire. If
PEX16_1 is set to x16 speed, then PEX16_2 would not be functional.

PEX1_1/PEX1_2: PCI-Express x1 Slots

- PCI-Express 1.0a compliant.
- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.
- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
- 2X bandwidth over the traditional PCI architecture.

PEX1_2

PEX16_1

PEX1_1

PEX16_2

12
 TPower I45

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

PWR_LED
On/Off
++ -
9 16
1 8
+ -
SPK RST
HLED

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A
N/A
2 N/A Speaker 10 N/A
3 N/A Connector 11 N/A N/A
4 Speaker 12 Power LED (+)
5 HDD LED (+) Hard drive 13 Power LED (+) Power LED
6 HDD LED (-) LED 14 Power LED (-)
7 Ground 15 Power button
Reset button Power-on button
8 Reset control 16 Ground

13
Motherboard Manual
JATXPWR2: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.

12 24

1 13

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

JATXPWR1: ATX Power Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.
4 1
Pin Assignment
1 +12V
2 +12V
8 5 3 +12V
4 +12V
5 Ground
6 Ground
7 Ground
8 Ground

Note:
Before power on the system, please make sure that both JATXPWR1 and JATXPWR2
connectors have been plugged-in.
If the CPU power plug is 4-pin, please plug it into Pin 1-2-5-6 of JATXPWR1.

14
 TPower I45

J1: Auxiliary Power for Graphics

This connector is an auxiliary power connection for graphics cards. Exclusive
power for the graphics card provides better graphics performance.

Pin Assignment
1 +12V
2 Ground
3 Ground
1 4 4 VCC

JUSB3/JUSB4/JUSB5: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

Pin Assignment
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
5 USB+
6 USB+
JUSB4 7 Ground
JUSB5 JUSB3 8 Ground
9 Key
9 1 10 NC

10 2

15
Motherboard Manual

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

Pin Assignment
1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in
9 1
10 Jack Sense

10 2

JCDIN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..

Pin Assignment
1 Left Channel Input
2 Ground
3 Ground
4 Right Channel Input
1

16
 TPower I45

JSPDIF_OUT1/JSPDIF_OUT2: Digital Audio-out Connectors

JSPDIF_OUT1 is for connecting the PCI bracket SPDIF output, and
JSPDIF_OUT2 is for connecting to the HDMI audio of VGA card.

Pin Assignment
1 +5V
2 SPDIF_OUT
1 3 Ground

JSPDIF_OUT2
JSPDIF_OUT1

3 1

JSPDIF_IN1: Digital Audio-in Connector

This connector allows user to connect the PCI bracket SPDIF input header.

Pin Assignment
1 +5V
2 SPDIF_IN
3 Ground

3 1

17
Motherboard Manual

JCOM1: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Pin Assignment
1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator
10 Key
9 1

10 2

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.

3 1

Pin 1-2 Close:

Normal Operation (default).

3 1

3 1

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.

18
 TPower I45

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:
JUSBV1: +5V for USB ports at JUSB1/JUSB2/JRJ45USB1.
JUSBV2: +5V for USB ports at JUSB3/JUSB4/JUSB5.
Pin 2-3 Close:
JUSBV1: +5V STB for USB ports at JUSB1/JUSB2/ JRJ45USB1.
JUSBV2: +5V STB for USB ports at JUSB3/JUSB4/JUSB5.

1 1
Pin 1-2 close
3
JUSBV1

3
JUSBV2
1
Pin 2-3 close
3 1

On-Board Buttons
There are 2 on-board buttons.

RSTSW2

PWRSW1

PWRSW1:
This is an on-board Power Switch button.
RSTSW2:
This is an on-board Reset button.

19
Motherboard Manual
BIOS POST Code/CPU Temperature Indicator
This indicator will show POST code while booting; after the booting sequence, it
will show current CPU temperature. Please refer to Chapter 7.4 for all the
BIOS POST codes.

JPE1~JPE9: CrossFire Switch Jumpers

The setting of these jumpers determines the operation mode of PEX16_1 and
PEX16_2. If you want to use the CrossFire function, these jumpers should be
set to Pin 2-3 close; and PEX16_1 and PEX16_2 will both run with x8 speed. If
these jumpers are set to Pin 1-2 close, PEX16_1 will run with x16 speed and
PEX16_2 will not be functional.

JPE1 JPE3 JPE5 JPE7

1 1
3 3
1 1
3 3
JPE2 JPE4 JPE6 JPE8
3 1

JPE9

JPE1 JPE3 JPE5 JPE7 JPE1 JPE3 JPE5 JPE7

1 1 1 1
3 3 3 3
1 1 1 1
3 3 3 3
JPE2 JPE4 JPE6 JPE8 JPE2 JPE4 JPE6 JPE8
JPE9 JPE9
3 1 3 1
Pin 1-2 Close Pin 2-3 Close:
Normal Operation CrossFire Operation
PEX16_1: x16 Speed PEX16_1: x8 Speed
PEX16_2: Not Functional PEX16_2: x8 Speed
20
 TPower I45

CHAPTER 4: CROSSFIRE FUNCTION

4.1 REQUIREMENTS
Only Windows XP/Vista supports CrossFire (Dual Video) function.
Two identical CrossFire-ready graphics cards that are ATI certified.
The graphics card driver should support CrossFire technology.
The power supply unit must provide at least the minimum power required by
the system, or the system will be unstable. A power supply above 500W is
recommended under CrossFire mode.

4.2 INSTALLING CROSSFIRE-READY GRAPHICS CARDS

Step 1: Power off the computer and set JPE1~JPE9 to Pin2-3 close.

JPE1 JPE3 JPE5 JPE7

1 1
3 3
1 1
3 3
JPE2 JPE4 JPE6 JPE8
3 1

JPE9

JPE1 JPE3 JPE5 JPE7 JPE1 JPE3 JPE5 JPE7

1 1 1 1
3 3 3 3
1 1 1 1
3 3 3 3
JPE2 JPE4 JPE6 JPE8 JPE2 JPE4 JPE6 JPE8
JPE9 JPE9
3 1 3 1
Pin 1-2 Close Pin 2-3 Close:
Normal Operation CrossFire Operation
PEX16_1: x16 Speed PEX16_1: x8 Speed
PEX16_2: Not Functional PEX16_2: x8 Speed

21
Motherboard Manual

Step 2: Insert the two CrossFire-Ready graphics cards into PEX16_1 (Master)
and PEX16_2 (Slave)

PEX16_1(Mas ter )

PEX16_2(Slave)

Notice: Make sure both the graphics cards are seated into slots
completely.

Step 3: Connect a 4-pin ATX power cable to Auxiliary Power Connector (J1),
this will ensure the stabilization of your system.

Step 4: Connect the CrossFire Bridge with two graphics cards. Installation
completes.

NOTE
For more detail information of hardware/software installation and
configuration of CrossFire function, please visit following web-sites:
http://ati.amd.com/technology/crossfire/tutorials.html
http://ati.amd.com/technology/crossfire/howitworksdemo.html

22
 TPower I45
CHAPTER 5: RAID FUNCTIONS
5.1 OPERATION SYSTEM
Supports Windows 2000 Professional, Windows XP, and Windows VISTA.

5.2 RAID ARRAYS

RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for
many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 1+0 (Onboard): RAID 1+0 combines the techniques used in RAID 0 and RAID 1.
RAID 5 (Onboard): RAID 5 provides fault tolerance and better utilization of disk capacity.

5.3 HOW RAID WORKS

RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large file into smaller blocks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.
Features and Benefits
­ Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the
platform.
­ Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
­ Benefits: provides increased data throughput, especially for large files. No
capacity loss penalty for parity.
­ Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
­ Fault Tolerance: No.

Block 1 Block 2
Block 3 Block 4
Block 5 Block 6

23
Motherboard Manual

RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliable
media.
Features and Benefits
­ Drives: Minimum 2, and maximum is 2.
­ Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
­ Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
­ Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
­ Fault Tolerance: Yes.

Block 1 Block 1
Block 2 Block 2
Block 3 Block 3

24
 TPower I45

RAID 1+0 (For Onboard SATA Only):

RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 1+0
solution for improved resiliency, performance and rebuild performance.
Features and Benefits
­ Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
­ Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.
­ Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
­ Fault Tolerance: Yes.

Block 1 Block 1 Block 2 Block 2

Block 3 Block 3 Block 4 Block 4
Block 5 Block 5 Block 6 Block 6

25
Motherboard Manual

RAID 5 (For Onboard SATA Only):

RAID 5 stripes both data and parity information across three or more drives. It writes
data and parity blocks across all the drives in the array. Fault tolerance is maintained by
ensuring that the parity information for any given block of data is placed on a different
drive from those used to store the data itself.
Features and Benefits
­ Drives: Minimum 3.
­ Uses: RAID 5 is recommended for transaction processing and general
purpose service.
­ Benefits: An ideal combination of good performance, good fault tolerance,
and high capacity and storage efficiency.
­ Drawbacks: Individual block data transfer rate same as a single disk. Write
performance can be CPU intensive.
­ Fault Tolerance: Yes.

Disk 1

DATA 1
DATA 3
PARITY
DATA 7
DATA 9
PARITY

Disk 2

DATA 2
PARITY
DATA 5
DATA 8
PARITY
DATA 11

Disk 3

PARITY
DATA 4
DATA 6
PARITY
DATA 10
DATA 12

26
 TPower I45

CHAPTER 6: T-POWER BIOS & SOFTWARE

6.1 T-POWER BIOS
T-Power BIOS Features
Overclocking Navigator Engine (O.N.E.)

Memory Integration Test (M.I.T., under Overclock Navigator Engine)

BIO-Flasher: Update BIOS file from USB Flash Drive or FDD

Self Recovery System (S.R.S)

Smart Fan Function

CMOS Reloading Program

!! WARNING !!
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in
this manual is for your reference only and the actual BIOS
information and settings on board may be different from this
manual. For further information of setting up the BIOS, please
refer to the BIOS Manual in the Setup CD.

A. Overclocking Navigator Engine (O.N.E.)

ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E Exit
Over-Clocking Navigator setting Options
WARNING: Setting wrong values in below sections
Normal
may cause system to malfunction. Automate OverClock
Over-Clocking Navigator [Normal] Manual OverClock
=========== Automate OverClock System ===========
Auto OverClock System [V6-Tech Engine]
============ Manual OverClock System ============
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x9.0]
CPU Frequency Setting [333]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto] Select Screen
DDR2 Enhanced Mode [Auto] Select Item
> DRAM Timing Configuration Enter Go to Sub Screen
> Clock Gen Configuration F1 General Help
> Voltage Configuration F10 Save and Exit
Memory Test [Disabled] ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

27
Motherboard Manual

Manual Overclock System (M.O.S.)

MOS is designed for experienced overclock users.
It allows users to customize personal overclock settings.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E Exit
Over-Clocking Navigator setting Options
WARNING: Setting wrong values in below sections Normal
may cause system to malfunction. Automate OverClock
Over-Clocking Navigator [Normal] Manual OverClock
=========== Automate OverClock System ===========
Auto OverClock System [V6-Tech Engine]
============ Manual OverClock System ============
Intel(R) SpeedStep(tm) tech Options
[Enabled]
Ratio CMOS Setting Normal
[ x9.0]
CPU Frequency Setting Automate
[333] OverClock
Manual
FSB(Bsel) To NorthBridge Latch OverClock
[Auto]
DRAM Frequency [Auto] Select Screen
DDR2 Enhanced Mode [Auto] Select Item
> DRAM Timing Configuration EnterGo to Sub Screen
> Clock Gen Configuration F1 General Help
> Voltage Configuration F10 Save and Exit
Memory Test [Disabled] ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

↓
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E Exit
Over-Clocking Navigator setting Options
WARNING: Setting wrong values in below sections Normal
may cause system to malfunction. Automate OverClock
Over-Clocking Navigator [Manual OverClock] Manual OverClock
=========== Automate OverClock System ===========
Auto OverClock System [V6-Tech Engine]
============ Manual OverClock System ============
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x9.0]
CPU Frequency Setting [333]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto] Select Screen
DDR2 Enhanced Mode [Auto] Select Item
> DRAM Timing Configuration EnterGo to Sub Screen
> Clock Gen Configuration F1 General Help
> Voltage Configuration F10 Save and Exit
Memory Test [Disabled] ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

Intel(R) SpeedStep(tm) Tech

This item allows you to enable SpeedStep technology for better power
saving. SpeedStep is a technology built into some Intel processors that
allows the clock speed of the processor to be dynamically changed by
software.
Ratio CMOS Setting
This item allows you to set the CPU ratio frequency. This item is
adjustable only when SpeedStep Tech is set to Disabled.
CPU Frequency Setting
CPU Frequency is directly in proportion to system performance. To
maintain the system stability, CPU voltage needs to be increased also
when raising CPU frequency.

28
 TPower I45
FSB(Bsel) To NorthBridge Latch
This item allows you to select the FSB Frequency.
DRAM Frequency
To get better system performance, sometimes downgrading the memory
frequency is necessary when CPU frequency is adjusted over the upper
limit.
DDR2 Enhanced Mode
This item allows you to control the DDR2 ram enhanced mode.
DRAM Timing Configuration
Enter this item for more advanced DRAM timing settings.
Clock Gen Configuration
Enter this item for more advanced Clock Gen settings.
Voltage Configuration
Enter this item for more advanced voltage settings.

NOTE
Overclock is an optional process, but not a “must-do” process; it is not
recommended for inexperienced users. Therefore, we will not be responsible
for any hardware damage which may be caused by overclocking. We also
would not guarantee any overclocking performance.

Automatic Overclock System (A.O.S.)

For beginners in overclock field, BET had developed an easy, fast, and
powerful feature to increase the system performance, named A.O.S.
Based on many tests and experiments, A.O.S. provides 3 ideal overclock
configurations that are able to raise the system performance in a single step.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E Exit
Over-Clocking Navigator setting Options
WARNING: Setting wrong values in below sections Normal
may cause system to malfunction. Automate OverClock
Over-Clocking Navigator [Normal] Manual OverClock
=========== Automate OverClock System ===========
Auto OverClock System [V6-Tech Engine]
============ Manual OverClock System ============
Intel(R) SpeedStep(tm) tech Options
[Enabled]
Ratio CMOS Setting Normal
[ x9.0]
CPU Frequency Setting Automate
[333] OverClock
Manual
FSB(Bsel) To NorthBridge Latch OverClock
[Auto]
DRAM Frequency [Auto] Select Screen
DDR2 Enhanced Mode [Auto] Select Item
> DRAM Timing Configuration EnterGo to Sub Screen
> Clock Gen Configuration F1 General Help
> Voltage Configuration F10 Save and Exit
Memory Test [Disabled] ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

29
Motherboard Manual
V6 Tech Engine
This engine will make a good over-clock performance.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E Exit
Over-Clocking Navigator setting Options
WARNING: Setting wrong values in below sections V6-Tech Engine
may cause system to malfunction. V8-Tech Engine
Over-Clocking Navigator [Automate OverClock] V12-Tech Engine
=========== Automate OverClock System ===========
Auto OverClock System [V6-Tech Engine]
============ Manual OverClock System ============
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x9.0]
CPU Frequency Setting [333]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto] Select Screen
DDR2 Enhanced Mode [Auto] Select Item
> DRAM Timing Configuration EnterGo to Sub Screen
> Clock Gen Configuration F1 General Help
> Voltage Configuration F10 Save and Exit
Memory Test [Disabled] ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

V8 Tech Engine
This engine will make a better over-clock performance.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E Exit
Over-Clocking Navigator setting Options
WARNING: Setting wrong values in below sections V6-Tech Engine
may cause system to malfunction. V8-Tech Engine
Over-Clocking Navigator [Automate OverClock] V12-Tech Engine
=========== Automate OverClock System ===========
Auto OverClock System [V8-Tech Engine]
============ Manual OverClock System ============
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x9.0]
CPU Frequency Setting [333]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto] Select Screen
DDR2 Enhanced Mode [Auto] Select Item
> DRAM Timing Configuration EnterGo to Sub Screen
> Clock Gen Configuration F1 General Help
> Voltage Configuration F10 Save and Exit
Memory Test [Disabled] ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

V12 Tech Engine

This engine will make a best over-clock performance.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E Exit
Over-Clocking Navigator setting Options
WARNING: Setting wrong values in below sections V6-Tech Engine
may cause system to malfunction. V8-Tech Engine
Over-Clocking Navigator [Automate OverClock] V12-Tech Engine
=========== Automate OverClock System ===========
Auto OverClock System [V12-Tech Engine]
============ Manual OverClock System ============
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x9.0]
CPU Frequency Setting [333]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto] Select Screen
DDR2 Enhanced Mode [Auto] Select Item
> DRAM Timing Configuration EnterGo to Sub Screen
> Clock Gen Configuration F1 General Help
> Voltage Configuration F10 Save and Exit
Memory Test [Disabled] ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

30
 TPower I45

Notices:
Not all types of Intel CPU perform above overclock setting ideally; the difference will be based on the
selected CPU model.

B. Memory Integration Test (M.I.T.)

This function is under “Overclocking Navigator Engine” item.
MIT allows users to test memory compatibilities, and no extra devices or
software are needed.
Step 1
The default setting under this item is “Disabled”; the condition parameter should
be changed to “Enable” to proceed this test.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E Exit
Over-Clocking Navigator setting Options
WARNING: Setting wrong values in below sections Disabled
may cause system to malfunction. Enabled
Over-Clocking Navigator [Normal]
=========== Automate OverClock System ===========
Auto OverClock System [V6-Tech Engine]
============ Manual OverClock System ============
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x9.0]
CPU Frequency Setting [333]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto] Select Screen
DDR2 Enhanced Mode [Auto] Select Item
> DRAM Timing Configuration EnterGo to Sub Screen
> Clock Gen Configuration F1 General Help
> Voltage Configuration F10 Save and Exit
Memory Test [Disabled] ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

↓
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E Exit
Over-Clocking Navigator setting Options
WARNING: Setting wrong values in below sections Disabled
may cause system to malfunction. Enabled
Over-Clocking Navigator [Normal]
=========== Automate OverClock System ===========
Auto OverClock System [V6-Tech Engine]
============ Manual OverClock System ============
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x9.0]
CPU Frequency Setting [333]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto] Select Screen
DDR2 Enhanced Mode [Auto] Select Item
> DRAM Timing Configuration EnterGo to Sub Screen
> Clock Gen Configuration F1 General Help
> Voltage Configuration F10 Save and Exit
Memory Test [Enabled] ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

Step 2
Save and Exit from CMOS setup and reboot the system to activate this test.
Run this test for 5 minutes (minimum) to ensure the memory stability.
Step 3
When the process is done, change the setting back from “Enable” to “Disable”
to complete the test.
31
Motherboard Manual

C. BIO-Flasher
BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.
The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.

4. Power on or reset the computer and then

press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.

5. The utility will show the BIOS

files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.

6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.

z This utility only allows storage device with FAT32/16 format and single
partition.
z Shutting down or resetting the system while updating the BIOS will lead to
system boot failure.

32
 TPower I45
D. Self Recovery System (S.R.S.)
This function can’t be seen under BIOS setup; and is always on whenever the
system starts up.
However, it can prevent system hang-up due to inappropriate overclock
actions.
When the system hangs up, S.R.S. will automatically log in the default BIOS
setting, and all overclock settings will be re-configured.

E. Smart Fan Function

Smart Fan Function is under “Smart Fan Configuration” in “Advanced Menu”.
This is a brilliant feature to control CPU/System Temperature vs. Fan speed.
When enabling Smart Fan function, Fan speed is controlled automatically by
CPU/System temperature.
This function will protect CPU/System from overheat problem and maintain the
system temperature at a safe level.

BIOS SETUP UTILITY

Main Advanced PCIPnP Boot Chipset O.N.E Exit

Advanced Settings Configure Smart Fan.

WARNING: Setting wrong values in below sections
may cause system to malfunction.
> CPU Configuration
> SuperIO Configuration
> Hardware Health Configuration
> Smart Fan Configuration
> Power Configuration
> Intel TXT(LT) Configuration
> Intel VT-d Configuration Select Screen
> MPS Configuration Select Item
> USB Configuration Enter Go to Sub Screen
> Config Onboard PCI/PCI-E Devices F1 General Help
F10 Save and Exit
ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

↓
BIOS SETUP UTILITY
Advanced

Smart Fan Configuration When you choice [Auto]

please run the
CPU Smart Fan [Disabled] calibration to define
Smart Fan Calibration the Fan parameters for
Smart Fan control
JSFAN1 Smart Fan [Disabled]
Fan Ctrl OFF(oC)
o
Fan Ctrl On( C)
Fan Ctrl Full On(oC)
Fan Ctrl Start value

JNFAN1 Smart Fan [Disabled] Select Screen

Fan Ctrl OFF(oC) Select Item
o
Fan Ctrl On( C) +- Change Option
o
Fan Ctrl Full On( C) F1 General Help
Fan Ctrl Start value F10 Save and Exit
ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

33
Motherboard Manual
Smart Fan Calibration
Choose this item and then the BIOS will automatically test and detect the
CPU/System fan functions and show CPU/System fan speed.

Fan Ctrl OFF(℃)

If the CPU/System temperature is lower than the set value, the CPU/
System fan will turn off. The range is from 0~127, with an interval of 1.

Fan Ctrl On(℃)

The CPU/System fan starts to work when CPU/System temperature
arrives to this set value. The range is from 0~127, with an interval of 1.

Fan Ctrl Full On(℃)

If the System Temperature reaches the set value, FAN will run in full speed.
The range is from 0~127, with an interval of 1.

Fan Ctrl Start Value

When CPU/System temperature arrives to the set value, the CPU/System
fan will work under Smart Fan Function mode. The range is from 0~127,
with an interval of 1.

F. CMOS Reloading Program

It allows users to save different CMOS settings into BIOS-ROM.
Users are able to reload any saved CMOS setting for customizing system
configurations. Moreover, users are able to save an ideal overclock setting
during overclock operation.
There are 10 sets of record addresses in total, and users are able to name the
CMOS data according to personal preference.

BIOS SETUP UTILITY

Main Advanced PCIPnP Boot Chipset O.N.E Exit

Exit Options

Save Changes and Exit

Discard Changes and Exit
Discard Changes

Load Optimal Defaults CMOS Backup Func

CMOS Data Reload
Security Settings CMOS Data Save
> Security
Select Screen
CMOS Backup Function Select Item
Enter Go to Sub Screen
F1 General Help
F10 Save and Exit
ESC Exit

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

34
 TPower I45

6.2 T-POWER SOFTWARE

T-Power2 is an integration of four functions: OC Tweaker for over-clock,
eHot-Line for technical support, BIOS-watch for system monitor, and Biostar
Flash for BIOS update.

Installing T-Power2
1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.

2. Select Software Installation, and then click on T-Power2.

3. Follow the on-screen instructions to complete the installation.

Launching T-Power2
After the installation process, you will see a “TPower2” icon
appears on the desktop. Double-click the TPower2 icon to
launch T-Power2 utility.

Main Panel
The main panel provides OC Tweaker, eHot-Line, BIO-watch, and Biostar
Flash buttons for launching the respective programs. Besides you can also
change the skin of the main panel.
Thi s area shows the inf ormati on
of the pointed butt on

Change Skin Program OFF

OC Tweaker eHOT-Li ne

BIO-watch Biostar Fl ash

35
Motherboard Manual

OC Tweaker
On the main panel, you can click on the OC Tweaker button to launch this
function. The OC Tweaker provides automatic/manual over-clock function for
BIOSTAR motherboard, and even for some BIOSTAR VGA card (VR8xxx
series only) which is powered by V-Ranger.
Th is a rea shows clo ck Th is a rea shows clo ck/vol ta ge V3/V6/V9/V12 /V1 5
infor matio n of th e VGA card infor matio n of th e CPU/motherb oard Fi xe d mod e ove r-clock

Te st the system

Auto over- cl ock

Man ual Adju st De lete curre nt

se tti ng file

Save curren t
se tti ng into fil e

Re store hardware
defaul t setting

Load p reviously
sa ve d settin g fi le

If you are not using a

nVIDI A VGA ca rd, this
windo w w ill not show.

If your have installed a

V-Ranger powered BIOSTAR
VGA card, then the left
window of the VGA card
information would show like
Tes t the VGA card Power Saving M ode
this. VGA card over-clock
Manual over-cloc k
Save current
VGA s etting into file
function will be enabled.
Restore VGA card D elete current
default setting VGA s etting file

Load prev ious saved

VGA setting file
36
 TPower I45

<Auto Over-clock>

By this function, the utility will set the best and stable performance and
frequency automatically.

Click on then a Warning dialog will

show. This dialog tells that all running
applications should be closed before the auto
over-clock procedure. The utility will do a
series of test continually; do not do any
operation during the test procedure. Click OK
to proceed or Cancel to stop.

After proceeding the tests would start, and a

warning message would continually show
telling that do not do any action to interfere
the testing procedure. The testing
procedure takes minutes; you can stop the
procedure by clicking Cancel.

For getting the best performance, the utility will repeat the test continually until the system
hang or fail, and then the system will auto-reboot. After that, launch the T-Power2 and enter
the OC Tweaker again, you will find the setting has been restored to a safest and best
performance status. Save this setting is recommended.

<Manual Over-clock>

To manually adjust the clock and voltage, just click the or beside the

number. (For V-Ranger powered VGA card, click then the

beside the VGA values will show.) After the adjustment, click to verify
the supplied value is recommended. If the test passes, following dialog will
show; click OK to proceed.

37
Motherboard Manual

<V3/V6/V9/V12/V15 Engine>
E X: This means V9 engine is acti vated.

By clicking ,
the utility would over-clock the system
with certain fixed percentage. When the
V3/V6/V9/V12/V15 engine is activated,
you will see the green light bar on the left
rising to the top of the button.
This function is recommended for
any inexperienced users.

<Save/Load/Delete Setting>

You can save current setting to a file by clicking , then a dialog as bellow
will show.

Enter file name and click “Save”, and then the current setting would be saved.

To load a previously saved file, click on , and the saved files would show
as bellow. Click on the file name and then choose “Yes” to load the setting.

To delete a previously saved file; load the setting first Æ click on (for VGA
setting is ) Æ choose “Yes”, and the setting file will be deleted.

(Be aware of that VGA setting for V-Ranger powered VGA card must be
saved/loaded/deleted respectively.)

Over-clock is an optional process but not a “must-do” process, and actual over-clock
result varies by every individual PC system. Therefore, we will neither guarantee any
over-clock performance nor be responsible for any system damage that may be caused
by over-clock. Any values or performance shown above are for reference only.
38
 TPower I45

BIO-watch
BIO-watch is a control and monitor utility that helps you to maintain the health
of the PC. It provides real-time information of CPU/GPU/System temperature,
fan speed, and voltage; and fan control function.
Th is area sh ows rea l-time i nformation of
tempe ratu re/fan speed/vo ltage Cu rrent fan speed Cu rrent CPU/GPU/System tempera tu re

Fa n co ntrol bars

Fa n
ca lib rate

Fa n
auto-control
ON/OFF

Fa n
co ntrol setti ng

Hi de
this utili ty

<Fan Calibrate>

At the very first time entering this utility,

fan calibrate will be made automatically.

After that you can also click to

manually calibrate the fan.

<Fan Auto/Manual Control>

When the “AUTO” button looks like , it means fans are under

auto-control. Click the button to then you can manually adjust fan
speed.

39
Motherboard Manual

Increase Speed

Auto-Control
OFF

Decrease Speed

Click the auto-control off and then the adjust level will show; use the level to
increase/decrease the fan speed. Be aware if the fan level been down to 0%,
the fan will still not completely stop; this is for your system’s protection.

<Fan Control Settings>

Click to enter the fan control

setting dialog. Here you can set CPU
temperature to control the fan; including
target CPU temperature, CPU
temperature for full fan speed, and CPU
temperature for shutdown system.
Besides, you can also see system
information in this dialog.

40
 TPower I45

eHot-Line
eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.
Before you use this utility, please set Outlook Express as your default e-mail client application program.

The main panel of eHot-Line shows

BIOS information, motherboard model
name, and chipset information, click on
“SETTING” to enter.

The Privacy Statement shows; and

please read through it. If you agree
with the statement, click “Yes” to
proceed; If not, click “No” to leave.

After agreeing with the privacy statement, fill up the table in the following dialog.

represents impor tant

*
infor mation that you
must provide. Without
this information, you may
not be able to send out
the mail.

*Descri be conditi on
of your system.

*Sel ect your area or

the area close to you.

Pr ovide the e-mail

addr ess that you would This block will show
like to send the copy to. the information which
would be collected in
the mail .
*Provide the name of
the memory module
manufacturer.

Provide the name of

the power supply
manufactur er and the Exit this dialog.
model no.

Send the mail out. Save these infor mation to a .txt file

41
Motherboard Manual

After filling up this information, click “Send”

to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.

Enter the file name and then click

“Save”. Your system information
will be saved to a .txt file.

Open the saved .txt file, you will see

your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.

If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web
http://www.biostar.com.tw/app/en-us/about/contact.php for getting
our contact information.

42
 TPower I45

Biostar Flash
Biostar Flash is a convenient utility which allows you to update your
motherboard BIOS under Windows system.

Shows curr ent BIOS

infor mati on

Restart Your System

(AMI BIOS)
Clear CMOS function
or
(Award BIOS)

Update BIOS Save current BIOS

with a B IOS fil e to a .bi n file

<Backup BIOS>

Once click on this button, the saving

dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.

After the saving process, finish

dialog will show. Click on OK to
complete the BIOS Backup
procedure.

43
Motherboard Manual

<Update BIOS>

Before doing this, please download the proper BIOS file from our website:
www.biostar.com.tw

Update BIOS procedure should be run with

Clear CMOS (or Restart) function, so please
check on Clear CMOS (or Restart) first. (Restart Your System)

Then click Update BIOS button, a

dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the

open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

The utility will update BIOS with the

proper BIOS file.

After the BIOS Update process, click on

OK to restart the system.

While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.
In the BIOS setup, choose Load Optimized Defaults and press
<Enter>Æ<Y>Æ<Enter>. After that use Save and Exit Setup to exit BIOS setup.
BIOS Update is completed.

All the information and content above about the T-Power 2 utility are subject to be
changed without notice. For better performance, the utility is being continuously
updated. The information and pictures described above are for your reference only.
The actual information and settings on board may be slightly different from this
manual.

44
 TPower I45
CHAPTER 7: USEFUL HELP
7.1 DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html

45
Motherboard Manual

7.2 EXTRA INFORMATION

CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown

automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.

Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.

46
 TPower I45
7.3 AMI BIOS BEEP CODE
Boot Block Beep Codes
Number of Beeps Description
1 No media present. (Insert diskette in floppy drive A:)
“AMIBOOT.ROM” file not found in root directory of diskette in
2
A:
3 Insert next diskette if multiple diskettes are used for recovery
4 Flash Programming successful
5 File read error
7 No Flash EPROM detected
10 Flash Erase error
11 Flash Program error
12 “AMIBOOT.ROM” file size error
BIOS ROM image mismatch (file layout does not match
13
image present in flash device)

POST BIOS Beep Codes

Number of Beeps Description
1 Memory refresh timer error
3 Base memory read/write test error
6 Keyboard controller BAT command failed
7 General exception error (processor exception interrupt error)
8 Display memory error (system video adapter)

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action
1, 3 Reseat the memory, or replace with known good modules.
Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.
z If beep codes are generated when all other expansion
6, 7 cards are absent, consult your system manufacturer’s
technical support.
z If beep codes are not generated when all other expansion
cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.
If the system video adapter is an add-in card, replace or
reseat the
8
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.

47
Motherboard Manual

7.4 AMI BIOS POST CODE

Checkpoint Description
Disable NMI, Parity, video for EGA, and DMA controllers. Initialize BIOS,
POST, Runtime data area. Also initialize BIOS modules on POST entry and
03
GPNV area. Initialized CMOS as mentioned in the Kernel Variable
"wCMOSFlags."
Check CMOS diagnostic byte to determine if battery power is OK and
CMOS checksum is OK. Verify CMOS checksum manually by reading
storage area. If the CMOS checksum is bad, update CMOS with power-on
04
default values and clear passwords. Initialize status register A.
Initializes data variables that are based on CMOS setup questions.
Initializes both the 8259 compatible PICs in the system
Initializes the interrupt controlling hardware (generally PIC) and interrupt
05
vector table.
Do R/W test to CH-2 count reg. Initialize CH-0 as system timer. Install the
06 POSTINT1Ch handler. Enable IRQ-0 in PIC for system timer interrupt.
Traps INT1Ch vector to "POSTINT1ChHandlerBlock."
07 Fixes CPU POST interface calling pointer.
Initializes the CPU. The BAT test is being done on KBC. Program the
08 keyboard controller command byte is being done after Auto detection of
KB/MS using AMI KB-5.
C0 Early CPU Init Start -- Disable Cache – Init Local APIC.
C1 Set up boot strap processor Information.
C2 Set up boot strap processor for POST.
C5 Enumerate and set up application processors.
C6 Re-enable cache for boot strap processor.
C7 Early CPU Init Exit.
0A Initializes the 8042 compatible Key Board Controller.
0B Detects the presence of PS/2 mouse.
0C Detects the presence of Keyboard in KBC port.
Testing and initialization of different Input Devices. Also, update the Kernel
Variables.
0E Traps the INT09h vector, so that the POST INT09h handler gets control for
IRQ1. Uncompress all available language, BIOS logo, and Silent logo
modules.
13 Early POST initialization of chipset registers.
20 Relocate System Management Interrupt vector for all CPU in the system.
Uncompress and initialize any platform specific BIOS modules. GPNV is
24
initialized at this checkpoint.
Initializes different devices through DIM.
2A
See DIM Code Checkpoints section of document for more information.
Initializes different devices. Detects and initializes the video adapter
2C
installed in the system that have optional ROMs.
2E Initializes all the output devices.
Allocate memory for ADM module and uncompress it. Give control to ADM
31 module for initialization. Initialize language and font modules for ADM.
Activate ADM module.
Initializes the silent boot module. Set the window for displaying text
33
information.

48
 TPower I45
Checkpoint Description
Displaying sign-on message, CPU information, setup key message, and any
37
OEM specific information.
Initializes different devices through DIM. See DIM Code Checkpoints section
38 of document for more information. USB controllers are initialized at this
point.
39 Initializes DMAC-1 & DMAC-2.
3A Initialize RTC date/time.
Test for total memory installed in the system. Also, Check for DEL or ESC
3B
keys to limit memory test. Display total memory in the system.
3C Mid POST initialization of chipset registers.
Detect different devices (Parallel ports, serial ports, and coprocessor in
40 CPU, etc.) successfully installed in the system and update the BDA,
EBDA…etc.
Updates CMOS memory size from memory found in memory test. Allocates
memory for Extended BIOS Data Area from base memory. Programming the
52
memory hole or any kind of implementation that needs an adjustment in
system RAM size if needed.
60 Initializes NUM-LOCK status and programs the KBD typematic rate.
75 Initialize Int-13 and prepare for IPL detection.
78 Initializes IPL devices controlled by BIOS and option ROMs.
7C Generate and write contents of ESCD in NVRam.
84 Log errors encountered during POST.
85 Display errors to the user and gets the user response for error.
87 Execute BIOS setup if needed / requested. Check boot password if installed.
8C Late POST initialization of chipset registers.
8D Build ACPI tables (if ACPI is supported).
8E Program the peripheral parameters. Enable/Disable NMI as selected.
Initialization of system management interrupt by invoking all handlers.
90
Please note this checkpoint comes right after checkpoint 20h.
A1 Clean-up work needed before booting to OS.
Takes care of runtime image preparation for different BIOS modules. Fill the
free area in F000h segment with 0FFh. Initializes the Microsoft IRQ Routing
A2
Table. Prepares the runtime language module. Disables the system
configuration display if needed.
A4 Initialize runtime language module. Display boot option popup menu.
Displays the system configuration screen if enabled. Initialize the CPU’s
A7
before boot, which includes the programming of the MTRR’s.
A9 Wait for user input at config display if needed.
AA Uninstall POST INT1Ch vector and INT09h vector.
AB Prepare BBS for Int 19 boot. Init MP tables.
End of POST initialization of chipset registers. De-initializes the ADM
AC
module.
Save system context for ACPI. Prepare CPU for OS boot including final
B1
MTRR values.
00 Passes control to OS Loader (typically INT19h).

49
Motherboard Manual

7.5 TROUBLESHOOTING
Probable Solution
1. No power to the system at all 1. Make sure power cable is
Power light don’t illuminate, fan securely plugged in.
inside power supply does not turn 2. Replace cable.
on. 3. Contact technical support.
2. Indicator light on keyboard does
not turn on.
System inoperative. Keyboard lights Using even pressure on both ends of
are on, power indicator lights are lit, the DIMM, press down firmly until the
and hard drive is spinning. module snaps into place.
System does not boot from hard disk 1. Check cable running from disk to
drive, can be booted from optical drive. disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from optical drive. 1. Back up data and applications
Hard disk can be read and applications files.
can be used but booting from hard disk 2. Reformat the hard drive.
is impossible. Re-install applications and data
using backup disks.
Screen message says “Invalid Review system’s equipment. Make sure
Configuration” or “CMOS Failure.” correct information is in setup.
Cannot boot system after installing 1. Set master/slave jumpers
second hard drive. correctly.
2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

50
 TPower I45

This page is intentionally left blank.

51
Motherboard Manual
APPENDENCIES: SPEC IN OTHER LANGUAGE
GERMAN
Spezifikationen
LGA 775
Unterstützt Execute Disable Bit / Enhanced Intel
Intel Intel Core2Duo / Core2Quad /
CPU SpeedStep® / Intel Architecture-64 / Extended
Pentium Dual-Core / Celeron Dual-Core /
Memory 64 Technology / Virtualization Technology
Celeron 4xx Prozessoren

FSB 800 / 1066 / 1333 / 1600 MHz

Intel P45
Chipsatz
Intel ICH10R
Fintek F71887F Umgebungskontrolle,
Bietet die häufig verwendeten alten Super Hardware-Überwachung
Super E/A
E/A-Funktionen. Lüfterdrehzahl-Controller/-Überwachung
Low Pin Count-Schnittstelle "Smart Guardian"-Funktion von ITE

DDR2 DIMM-Steckplätze x 4 Dual-Kanal DDR2 Speichermodul

Arbeitsspeich Jeder DIMM unterstützt 256MB / 512MB / Unterstützt DDR2 1066 / 800 / 667
er 1GB / 2GB DDR2. registrierte DIMMs. ECC DIMMs werden nicht
Max. 8GB Arbeitsspeicher unterstützt.
Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus
IDE Marvell 88SE6121
Unterstützt PIO-Modus 0~4,
Datentransferrate bis zu 3Gb/s
SATA II ICH10R Konform mit der SATA-Spezifikation Version 2.0.
Unterstützt RAID 0 / 1 / 5 / 1+0
Datentransferrate bis zu 3Gb/s
eSATA Marvell 88SE6121 Konform mit der SATA-Spezifikation Version 2.0.
Unterstützt Port-Multiplier/RAID 0,1

10 / 100 / 1000 Mb/s Auto-Negotiation

LAN Realtek RTL 8111C
Halb-/ Vollduplex-Funktion
HD
Unterstützt High-Definition Audio
Audio-Unters ALC888S
7.1-Kanal-Audioausgabe
tützung

PCI-Steckplatz x2
PCI Express Gen2 x16 Steckplatz
(x16/x8) x1
Steckplätze
PCI Express Gen2 x16 Steckplatz
(x8) x1

PCI Express x1 Steckplatz x2

52
 TPower I45
Spezifikationen

Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke

Serieller Anschluss x1

IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss x6 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CD-IN-Anschluss x1 Unterstützt die CD Audio-In-Funktion

S/PDIF Ausgangsanschluss x2 Unterstützt die digitale Audioausgabefunktion
Onboard-Ans S/PDIF Eingangsanschluss x1 Unterstützt die digitale Audioeingabefunktion
chluss CPU-Lüfterstromversorgungsanschluss (mit Smart
CPU-Lüfter-Sockel x1
Fan-Funktion)
System-Lüfter-Sockel x2 System-Lüfter-Stromversorgungsanschluss
"CMOS löschen"-Sockel x1
Jeder Anschluss unterstützt 2
USB-Anschluss x3
Fronttafel-USB-Anschlüsse
Stromanschluss (24-polig) x1

Stromanschluss (8-polig) x1
Stromanschluss (4-polig) x1

PS/2-Tastatur x1

PS/2-Maus x1
Rückseiten-E LAN-Anschluss x1
/A USB-Anschluss x6
Audioanschluss x6
eSATA Anschluss x2

Platinengröße 244 mm (B) X 305 mm (L) ATX

Biostar behält sich das Recht vor, ohne Ankündigung
OS-Unterstüt
Windows 2000 / XP / VISTA die Unterstützung für ein Betriebssystem
zung
hinzuzufügen oder zu entfernen.

53
Motherboard Manual

FRANCE
SPEC

LGA 775 Prend en charge les technologies d'exécution de bit de

Processeurs Intel Core2Duo / Core2Quad désactivation / Intel SpeedStep® optimisée/

UC
/ Pentium Dual-Core / Celeron Dual-Core / d'architecture Intel 64 / de mémoire étendue 64 / de

Celeron 4xx virtualisation

Bus frontal 800 / 1066 / 1333 / 1600 MHz

Intel P45
Chipset
Intel ICH10R

Fintek F71887F Initiatives de contrôle environnementales,

Fournit la fonctionnalité de Super E/S Moniteur de matériel

Super E/S
patrimoniales la plus utilisée. Contrôleur /moniteur de vitesse de ventilateur

Interface à faible compte de broches Fonction "Gardien intelligent" de l'ITE

Fentes DDR2 DIMM x 4 Module de mémoire DDR2 à mode à double voie

Mémoire Chaque DIMM prend en charge des DDR2 Prend en charge la DDR2 1066 / 800 / 667

principale de 256Mo / 512Mo / 1Go / 2Go Les DIMM à registres et DIMM avec code correcteurs

Capacité mémoire maximale de 8Go d'erreurs ne sont pas prises en charge

Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133

IDE Marvell 88SE6121
Prend en charge le mode PIO 0~4,

Taux de transfert jusqu'à 3 Go/s.

SATA II ICH10R Conforme à la spécification SATA Version 2.0

Prise en charge RAID 0 / 1 / 5 / 1+0

Taux de transfert jusqu'à 3 Go/s.

eSATA Marvell 88SE6121 Conforme à la spécification SATA Version 2.0

Prise en charge Port-Miltiplier/ RAID 0,1

10 / 100 / 1000 Mb/s négociation automatique

LAN Realtek RTL 8111C
Half / Full duplex capability

Prise en
Prise en charge de l'audio haute définition
charge ALC888S
Sortie audio à 7.1 voies
audio HD

Fente PCI x2

Fente PCI Express Gen2 x16

(x16/x8) x1
Fentes
Fente PCI Express Gen2 x16

(x8) x1
Fente PCI Express x1 x2

54
 TPower I45
SPEC

Chaque connector prend en charge 2 lecteurs de

Connecteur de disquette x1
disquettes

Port série x1

Chaque connecteur prend en charge 2 périphériques

Connecteur IDE x1
IDE

Chaque connecteur prend en charge 1 périphérique

Connecteur SATA x6
SATA

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant

Connecteur d'entrée CD x1 Prend en charge la fonction d'entrée audio de CD

Connecteur de sortie S/PDIF x2 Prend en charge la fonction de sortie audio numérique

Connecteur Connecteur d'entrée S/PDIF x1 Prend en charge la fonction d'entrée audio numérique
embarqué Alimentation électrique du ventilateur UC (avec
Embase de ventilateur UC x1
fonction de ventilateur intelligent)

Embase de ventilateur système x2 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Chaque connecteur prend en charge 2 ports USB de

Connecteur USB x3
panneau avant

Connecteur d'alimentation x1

(24 broches)

Connecteur d'alimentation x1

(8 broches)
Connecteur d'alimentation x1

(4 broches)

Clavier PS/2 x1

Souris PS/2 x1
E/S du
Port LAN x1
panneau
Port USB x6
arrière
Fiche audio x6

Port eSATA x2

Dimensions
244 mm (l) X 305 mm (H) ATX
de la carte

Biostar se réserve le droit d'ajouter ou de supprimer le

Support SE Windows 2000 / XP / VISTA
support de SE avec ou sans préavis.

55
Motherboard Manual

ITALIAN
SPECIFICA

LGA 775 Supporto di Execute Disable Bit / Enhanced

Processore Intel Core2Duo / Core2Quad Intel SpeedStep® / Architettura Intel 64 /

CPU
/ Pentium Dual-Core / Tecnologia Extended Memory 64 / Tecnologia

Celeron Dual-Core / Celeron 4xx Virtualization

FSB 800 / 1066 / 1333 / 1600 MHz

Intel P45
Chipset
Intel ICH10R

Fintek F71887F Funzioni di controllo dell’ambiente:

Fornisce le funzionalità legacy Super I/O Monitoraggio hardware
Super I/O
usate più comunemente. Controller / Monitoraggio velocità ventolina

Interfaccia LPC (Low Pin Count) Funzione "Smart Guardian" di ITE

Alloggi DIMM DDR2 x 4 Modulo di memoria DDR2 a canale doppio

Memoria Ciascun DIMM supporta DDR2 256MB / Supporto di DDR2 1066 / 800 / 667

principale 512MB / 1GB / 2GB DIMM registrati e DIMM ECC non sono

Capacità massima della memoria 8GB supportati

Modalità Bus Master Ultra DMA 33 / 66 / 100 /

IDE Marvell 88SE6121 133

Supporto modalità PIO Mode 0-4

Velocità di trasferimento dei dati fino a 3 Gb/s.

SATA II ICH10R Compatibile specifiche SATA Versione 2.0.

Supporto RAID 0 / 1 / 5 / 1+0

Velocità di trasferimento dei dati fino a 3 Gb/s.

eSATA Marvell 88SE6121 Compatibile specifiche SATA Versione 2.0.

Supporto Port-Miltiplier/RA ID 0,1

Negoziazione automatica 10 / 100 / 1000 Mb/s

LAN Realtek RTL 8111C
Capacità Half / Full Duplex

Supporto Supporto audio High-Definition (HD)

ALC888S
audio HD Uscita audio 7.1 canali

Alloggio PCI x2

Alloggio PCI Express Gen2 x16

(x16/x8) x1
Alloggi
Alloggio PCI Express Gen2 x16

(x8) x1
Alloggio PCI Express x1 x2

56
 TPower I45
SPECIFICA

Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy

Porta seriale x1

Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

Connettore SATA x6 Ciascun connettore supporta 1 unità SATA

Connettore pannello frontale x1 Supporta i servizi del pannello frontale

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Connettore CD-in x1 Supporta la funzione input audio CD

Connettore output SPDIF x2 Supporta la funzione d’output audio digitale

Connettore input S/PDIF x1 Supporta la funzione d’input audio digitale

Alimentazione ventolina CPU (con funzione

Connettori Collettore ventolina CPU x1
Smart Fan)
su scheda
Collettore ventolina sistema x2 Alimentazione ventolina di sistema

Collettore cancellaz ione CMOS x1

Ciascun connettore supporta 2 porte USB

Connettore USB x3
pannello frontale

Connettore alimentazione x1

(24 pin)

Connettore alimentazione x1

(8 pin)
Connettore alimentazione x1

(4 pin)

Tastiera PS/2 x1

Mouse PS/2 x1
I/O
Porta LAN x1
pannello
Porta USB x6
posteriore
Connettore audio x6

Porta eSATA x2

Dimension 244 mm (larghezza) x 305 mm

ATX
i scheda (altezza)

Sistemi Biostar si riserva il diritto di aggiungere o

operativi Windows 2000 / XP / VISTA rimuovere il supporto di qualsiasi sistema

supportati operativo senza preavviso.

57
Motherboard Manual

SPANISH
Especificación

LGA 775 Admite Bit de deshabilitación de ejecución / Intel

Procesador Intel Core2Duo / Core2Quad / SpeedStep® Mejorado / Intel Architecture-64 /

CPU
Pentium Dual-Core / Celeron Dual-Core / Tecnología Extended Memory 64 / Tecnología de

Celeron 4xx virtualización

FSB 800 / 1066 / 1333 / 1600 MHz

Conjunto de Intel P45

chips Intel ICH10R

Fintek F71887F Iniciativas de control de entorno,

Le ofrece las funcionalidades heredadas de Monitor hardware

Súper E/S
uso más común Súper E/S. Controlador/monitor de velocidad de ventilador

Interfaz de cuenta Low Pin Función "Guardia inteligente" de ITE

Ranuras DIMM DDR2 x 4 Módulo de memoria DDR2 de canal Doble

Memoria Cada DIMM admite DDR de 256MB / Admite DDR2 de 1066 / 800 / 667

principal 512MB / 1GB / 2GB No admite DIMM registrados o DIMM compatibles con

Capacidad máxima de memoria de 8GB ECC

Modo bus maestro Ultra DMA 33 / 66 / 100 / 133

IDE Marvell 88SE6121
Soporte los Modos PIO 0~4,

Tasas de transferencia de hasta 3 Gb/s.

SATA II ICH10R Compatible con la versión SATA 2.0.

Admite RAID 0 / 1 / 5 / 1+0

Tasas de transferencia de hasta 3 Gb/s.

eSATA Marvell 88SE6121 Compatible con la versión SATA 2.0.

Admite Port-Multiplier/RAID 0,1

Negociación de 10 / 100 / 1000 Mb/s

Red Local Realtek RTL 8111C
Funciones Half / Full dúplex

Soporte de Soporte de sonido de Alta Definición

ALC888S
sonido HD Salida de sonido de 7.1 canales

Ranura PCI X2

Ranura PCI Express Gen2 x16

(x16/x8) X1
Ranuras
Ranura PCI Express Gen2 x16

(x8) X1

Ranura PCI Express x1 X2

58
 TPower I45
Especificación

Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible

Puerto serie X1

Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Conector SATA X6 Cada conector soporta 1 dispositivos SATA

Conector de panel frontal X1 Soporta instalaciones en el panel frontal

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Conector de entrada de CD X1 Soporta función de entrada de sonido de CD

Conector de salida S/PDIF X2 Soporta función de salida de sonido digital

Conector de entrada S/PDIF X1 Soporta función de entrada de sonido digital

Conectores Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

en placa función Smart Fan)

Cabecera de ventilador de sistema X2 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X3 Cada conector soporta 2 puertos USB frontales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(8 patillas)

Conector de alimentación X1

(4 patillas)

Teclado PS/2 X1

Ratón PS/2 X1
Panel
Puerto de red local X1
trasero de
Puerto USB X6
E/S
Conector de sonido X6

Puerto eSATA X2

Tamaño de
244 mm. (A) X 305 Mm. (H) ATX
la placa

Soporte de
Biostar se reserva el derecho de añadir o retirar el
sistema Windows 2000 / XP / VISTA
soporte de cualquier SO con o sin aviso previo.
operativo

59
Motherboard Manual

PORTUGUESE
ESPECIFICAÇÕES
LGA 775
Suporta as tecnologias Execute Disable Bit / Enhanced
Processador Intel Core2Duo / Core2Quad
CPU Intel SpeedStep® / Intel Arquitecture -64 / Extended
/ Pentium Dual-Core / Celeron Dual-Core /
Memory 64 / Virtualization
Celeron 4xx
FSB 800 / 1066 / 1333 / 1600 MHz
Intel P45
Chipset
Intel ICH10R
Fintek F71887F
Iniciativas para controlo do ambiente
Proporciona as funcionalidades mais
Especificaçã Monitorização do hardware
utilizadas em termos da especificação
o Super I/O Controlador/Monitor da velocidade da ventoinha
Super I/O.
Função "Smart Guardian" da ITE
Interface LPC (Low Pin Count).
Ranhuras DIMM DDR2 x 4
Módulo de memória DDR2 de canal duplo
Cada módulo DIMM suporta uma
Memória Suporta módulos DDR2 1066 / 800 / 667
memória DDR2 de 256 MB / 512 MB / 1GB
principal Os módulos DIMM registados e os DIMM ECC não são
/ 2GB
suportados
Capacidade máxima de memória:8 GB
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
IDE Marvell 88SE6121
Suporta o modo PIO 0~4,
Velocidades de transmissão de dados até 3 Gb/s.
SATA II ICH10R Compatibilidade com a especificação SATA versão 2.0.
Suporta as funções RAID 0 / 1 / 5 / 1+0
Velocidades de transmissão de dados até 3 Gb/s.
eSATA Marvell 88SE6121 Compatibilidade com a especificação SATA versão 2.0.
Suporta as funções Port-Multiplier/RAID 0,1
Auto negociação de 10 / 100 / 1000 Mb/s
LAN Realtek RTL 8111C
Capacidade semi/full-duplex
Suporte
para áudio Suporta a especificação High-Definition Audio
ALC888S
de alta Saída de áudio de 7.1 canais
definição
Ranhura PCI x2
Ranhura PCI Express Gen2 x16
(x16/x8) x1
Ranhuras
Ranhura PCI Express Gen2 x16
(x8) x1
Ranhura PCI Express x1 x2

60
 TPower I45
ESPECIFICAÇÕES
Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes
Porta série x1
Conector IDE x1 Cada conector suporta 2 dispositivos IDE
Conector SATA x6 Cada conector suporta 1 dispositivo SATA
Conector do painel frontal x1 Para suporte de várias funções no painel frontal
Conector de áudio frontal x1 Suporta a função de áudio no painel frontal
Conector para entrada de CDs x1 Suporta a entrada de áudio a partir de CDs
Conector de saída S/PDIF x2 Suporta a saída de áudio digital
Conector de entrada S/PDIF x1 Suporta a entrada de áudio digital
Conectores Alimentação da ventoinha da CPU (com a função Smart
Conector da ventoinha da CPU x1
na placa Fan)
Conector da ventoinha do sistema x2 Alimentação da ventoinha do sistema
Conector para limpeza do CMOS x1
Conector USB x3 Cada conector suporta 2 portas USB no painel frontal
Conector de alimentação x1
(24 pinos)
Conector de alimentação x1
(8 pinos)
Conector de alimentação x1
(4 pinos)
Teclado PS/2 x1
Entradas/S Rato PS/2 x1
aídas no Porta LAN x1
painel Porta USB x6
traseiro Tomada de áudio x6
Porta eSATA x2
Tamanho
244 mm (L) X 305 mm (A) ATX
da placa
Sistemas A Biostar reserva-se o direito de adicionar ou remover
operativos Windows 2000 / XP / VISTA suporte para qualquer sistema operativo com ou sem
suportados aviso prévio.

61
Motherboard Manual

POLISH
SPEC

LGA 775
Obsługa Execute Disable Bit / Enhanced Intel
Procesor Intel Core2Duo / Core2Quad /
Procesor SpeedStep® / Intel Architecture-64 / Extended
Pentium Dual-Core / Celeron Dual-Core /
Memory 64 Technology / Virtualization Technology
Celeron 4xx

FSB 800 / 1066 / 1333 / 1600 MHz

Intel P45
Chipset
Intel ICH10R

Gniazda DDR2 DIMM x 4

Moduł pamięci DDR2 z trybem podwójnego kanału
Pamięć Każde gniazdo DIMM obsługuje moduły
Obsługa DDR2 1066 / 800 / 667
główna 256MB / 512MB / 1GB / 2GB
Brak obsługi Registered DIMM oraz ECC DIMM
Maks. wielkość pamięci 8GB

Fintek F71887F Funkcje kontroli warunków pracy,

Zapewnia najbardziej powszechne funkcje Monitor H/W

Super I/O
Super I/O. Kontroler/Monitor prędkości wentylatora

Interfejs Low Pin Count Funkcja ITE "Smart Guardian"

Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master

IDE Marvell 88SE6121
obsługa PIO tryb 0~4,

Transfer danych do 3 Gb/s.

SATA II ICH10R Zgodność ze specyfikacją SATA w wersji 2.0.

Obsługa RAID 0 / 1 / 5 / 1+0

Transfer danych do 3 Gb/s.

eSATA Marvell 88SE6121 Zgodność ze specyfikacją SATA w wersji 2.0.

Obsługa Port-Multiplier/RAID 0,1

10 / 100 / 1000 Mb/s z automatyczną negocjacją

LAN Realtek RTL 8111C szybkości

Działanie w trybie połowicznego / pełnego dupleksu

Obsługa Obsługa High-Definition Audio

ALC888S
audio HD 7.1 kanałowe wyjście audio

Gniazdo PCI x2

Gniazdo PCI Express Gen2 x16

(x16/x8) x1
Gniazda
Gniazdo PCI Express Gen2 x16

(x8) x1
Gniazdo PCI Express x1 x2

62
 TPower I45
SPEC

Złącze napędu dyskietek x1 Każde złącze obsługuje 2 napędy dyskietek

Port szeregowy x1

Złącze IDE x1 Każde złącze obsługuje 2 urządzenia IDE

Złącze SATA x6 Każde złącze obsługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim

Złącze wejścia CD x1 Obsługa funkcji wejścia audio CD

Złącze wyjścia S/PDIF x2 Obsługa funkcji cyfrowego wyjścia audio

Złącze wejścia S/PDIF x1 Obsługa funkcji cyfrowego wejścia audio

Złącza
Złącze główkowe wentylatora
wbudowane Zasilanie wentylatora procesora (z funkcją Smart Fan)
procesora x1

Złącze główkowe wentylatora

Zasilanie wentylatora systemowego
systemowego x2

Złącze główkowe kasowania CMOS x1

Każde złącze obsługuje 2 porty USB na panelu

Złącze USB x3
przednim

Złącze zasilania (24 pinowe) x1

Złącze zasilania (8 pinowe) x1

Złącze zasilania (4 pinowe) x1

Klawiatura PS/2 x1

Mysz PS/2 x1

Back Panel Port LAN x1

I/O Port USB x6

Gniazdo audio x6

Port eSATA x2

Wymiary
244 mm (S) X 305 mm (W) ATX
płyty

Obsluga
Biostar zastrzega sobie prawo dodawania lub
systemu
Windows 2000 / XP / VISTA odwoływania obsługi dowolnego systemu
operacyjne
operacyjnego bez powiadomienia.
go

63
Motherboard Manual

RUSSIAN
СПЕЦ
CPU LGA 775 Поддержка технологий Execute Disable Bit /
(центральн Процессор Intel Core2Duo / Core2Quad / Enhanced Intel SpeedStep® / Intel Architecture-64
ый Pentium Dual-Core / Celeron Dual-Core / / Extended Memory 64 Technology / технологии
процессор) Celeron 4xx виртуализация
FSB 800 / 1066 / 1333 / 1600 МГц
Набор Intel P45
микросхем Intel ICH10R
Слоты DDR2 DIMM x 4 Модуль памяти с двухканальным режимом DDR2
Основная Каждый модуль DIMM поддерживает 256 Поддержка DDR2 1066 / 800 / 667
память МБ / 512МБ / 1ГБ / 2ГБ DDR2 Не поддерживает зарегистрированные модули
Максимальная ёмкость памяти 8ГБ DIMM and ECC DIMM
Fintek F71887F Инициативы по охране окружающей среды,
Обеспечивает наиболее используемые Аппаратный монитор
Super I/O действующие функциональные Регулятор скорости вентилятора/ монитор
возможности Super I/O. Функция ITE "Smart Guardian"
Интерфейс с низким количеством выводов (Интеллектуальная защита)
Режим "хозяина" шины Ultra DMA 33 / 66 / 100 /
IDE Marvell 88SE6121 133
Поддержка режима PIO 0~4,
скорость передачи данных до 3 гигабит/с.
SATA II ICH10R Соответствие спецификации SATA версия 2.0.
Поддержка RAID 0 / 1 / 5 / 1+0
скорость передачи данных до 3 гигабит/с.
eSATA Marvell 88SE6121 Соответствие спецификации SATA версия 2.0.
Поддержка Port-Multiplier/RAID 0,1
Автоматическое согласование 10 / 100 / 1000
Локальная
Realtek RTL 8111C Мб/с
сеть
Частичная / полная дуплексная способность
Звуковая
поддержка Звуковая поддержка High-Definition
ALC888S
жесткого 7.1канальный звуковой выход
диска
Слот PCI x2
Слот PCI Express Gen2 x16
(x16/x8) x1
Слоты
Слот PCI Express Gen2 x16
(x8) x1
Слот PCI Express x1 x2

64
 TPower I45
СПЕЦ
Каждый разъём поддерживает 2 накопителя на
Разъём НГМД x1
гибких магнитных дисках
Последовательный порт x1
Каждый разъём поддерживает 2 встроенных
Разъём IDE x1
интерфейса накопителей
Разъём SATA x6 Каждый разъём поддерживает 1 устройство SATA
Разъём на лицевой панели x1 Поддержка устройств на лицевой панели
Поддержка звуковых функций на лицевой
Входной звуковой разъём x1
панели
Разъём ввода для CD x1 Поддержка функции ввода для CD
Разъём вывода для S/PDIF x2 Поддержка вывода цифровой звуковой функции
Встроенны Разъём ввода для S/PDIF x1 Поддержка ввода цифровой звуковой функции
й разъём Источник питания для вентилятора центрального
Контактирующее приспособление
процессора (с функцией интеллектуального
вентилятора центрального процессора x1
вентилятора)
Контактирующее приспособление
Источник питания для вентилятора системы
вентилятора системы x2
Открытое контактирующее
приспособление CMOS x1
Каждый разъём поддерживает 2 USB-порта на
USB-разъём x3
лицевой панели
Разъем питания (24 вывод) x1
Разъем питания (8 вывод) x1
Разъем питания (4 вывод) x1
Клавиатура PS/2 x1
Задняя Мышь PS/2 x1
панель Порт LAN x1
средств USB-порт x6
ввода-выв Гнездо для подключения
ода наушников x6
eSATA порт x2
Размер
244 мм (Ш) X 305 мм (В) ATX
панели
Biostar сохраняет за собой право добавлять или
Поддержка
Windows 2000 / XP / VISTA удалять средства обеспечения для OS с или без
OS
предварительного уведомления.

65
‫‪Motherboard Manual‬‬

‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬

‫‪Execute Disable Bit / Enhanced Intel‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت‬ ‫‪LGA 775‬‬

‫‪SpeedStep® / Intel Architecture-64 / Extended‬‬ ‫‪Intel Core2Duo / Core2Quad /‬ﻣﻌﺎﻟﺠﺎت‬ ‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬

‫‪Memory 64 Technology / Virtualization‬‬ ‫‪Pentium Dual-Core / Celeron Dual-Core /‬‬ ‫اﻟﻤﺮآﺰیﺔ‬

‫‪Technology‬‬ ‫ﺑﺘﺮدد یﺼﻞ إﻟﻰ ‪Celeron 4xx‬‬

‫اﻟﻨﺎﻗﻞ اﻷﻣﺎﻣﻲ اﻟﺠﺎﻥﺒﻲ ﻣﻴﺠﺎ هﺮﺗﺰ ‪ 800 / 1066 / 1333 / 1600‬ﺗﺮدد‬

‫‪Intel P45‬‬
‫ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫‪Intel ICH10R‬‬

‫ﻋﺪد‪4‬‬ ‫ﻓﺘﺤﺔ ‪DDR2 DIMM‬‬

‫ﻣﺰدوﺝﺔ اﻟﻘﻨﺎة‪DDR2‬وﺣﺪة ذاآﺮة‬
‫ﻣﻴﺠﺎ ‪ 256/512‬ﺳﻌﺔ ‪ DDR2‬ﺗﺪﻋﻢ ذاآﺮة ﻣﻦ ﻥﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫ﺳﻌﺎت ‪ 1066 / 800 / 667‬ﻣﻴﺠﺎ ﺑﺎیﺖ‪DDR2‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮع‬ ‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫ﺑﺎیﺖ و‪ 2‬ﺑﺎیﺖ و‪ 1‬ﺝﻴﺠﺎ ﺑﺎیﺖ‬
‫‪ ECC‬وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻣﻊ ‪DIMM‬ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 8‬ﺝﻴﺠﺎ ﺑﺎیﺖ‬

‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬

‫‪Fintek F71887F‬‬
‫ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻣًﺎ‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬ ‫‪Super I/O‬‬
‫ﻣﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ‬
‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪ ITE‬ﻣﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬

‫وﺿﻊ رﺋﻴﺴﻲ‪Ultra DMA 33 / 66 / 100 / 133‬ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ‬

‫‪Marvell 88SE6121‬‬ ‫ﻣﻨﻔﺬ ‪IDE‬‬
‫‪PIO Mode 0~4‬دﻋﻢ وﺿﻊ‬

‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ ‪ 3‬ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪.‬‬

‫‪ 2.0.‬اﻹﺹﺪار‪SATA‬ﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬ ‫‪ICH10R‬‬ ‫‪SATA II‬‬

‫‪RAID 0 / 1 / 5 / 1+0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬

‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ ‪ 3‬ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪.‬‬

‫‪ 2.0.‬اﻹﺹﺪار‪SATA‬ﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬ ‫‪Marvell 88SE6121‬‬ ‫‪eSATA‬‬

‫‪RAID 0,1 /Port-Multiplier‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬

‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻣﻴﺠﺎ ﺑﺎیﺖ ‪ /‬ﺙﺎﻥﻴﺔ و‪1‬ﺝﻴﺠﺎ ﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‬

‫‪Realtek RTL 8111C‬‬ ‫ﺷﺒﻜﺔ داﺧﻠﻴﺔ‬
‫إﻣﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻣﻞ‪/‬اﻟﻨﺼﻔﻲ‬

‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻣﻦ‬ ‫دﻋﻢ اﻝﺼﻮت ﻋﺎﻝﻲ‬

‫‪ALC888S‬‬
‫‪ 7.1‬ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‬ ‫اﻝﺘﻌﺮیﻒ‬

‫ﻋﺪد ‪2‬‬ ‫ﻓﺘﺤﺔ ‪PCI‬‬

‫)‪(x16/x8‬ﻓﺘﺤﺔ ‪PCI Express Gen2 x16‬ﻋﺪد ‪1‬‬
‫اﻝﻔﺘﺤﺎت‬
‫)‪(x8‬ﻓﺘﺤﺔ ‪ PCI Express Gen2 x16‬ﻋﺪد ‪1‬‬
‫ﻋﺪد ‪2‬‬ ‫ﻓﺘﺤﺔ ‪PCI Express x1‬‬

‫‪66‬‬
 ‫‪TPower I45‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬

‫یﺪﻋﻢ ﻣﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻥﺔ‬ ‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ﻣﺤﺮك أﻗﺮاص ﻣﺮﻥﺔ‬
‫ﻋﺪد‪1‬‬ ‫ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ‬
‫‪IDE‬یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ اﺙﻨﻴﻦ ﻣﻦ أﺝﻬﺰة‬ ‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ‪IDE‬‬
‫‪SATA‬یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺝﻬﺰة‬ ‫ﻋﺪد ‪6‬‬ ‫ﻣﻨﻔﺬ ‪SATA‬‬
‫یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬ ‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬ ‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻣﺞ‬ ‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ‪CD-IN‬‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ‬ ‫ﻋﺪد ‪2‬‬ ‫ﻣﻨﻔﺬ ﺥﺮج ‪S/PDIF‬‬ ‫اﻝﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬

‫یﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ اﻟﺼﻮت اﻟﺮﻗﻤﻲ‬ ‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ دﺥﻞ ‪S/PDIF‬‬ ‫اﻝﻠﻮﺡﺔ‬

‫‪Smart Fan‬ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻣﻊ وﻇﻴﻔﺔ‬ ‫ﻋﺪد ‪1‬‬ ‫وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬ ‫ﻋﺪد ‪2‬‬ ‫وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪1‬‬ ‫وﺹﻠﺔ ﻣﺴﺢ ‪CMOS‬‬
‫ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‪USB‬یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ‬ ‫ﻋﺪد ‪3‬‬ ‫ﻣﻨﻔﺬ ‪USB‬‬
‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪8‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﺎﺑﻴﺲ(‬

‫ﻋﺪد ‪1‬‬ ‫ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ ‪PS/2‬‬

‫ﻋﺪد ‪1‬‬ ‫ﻣﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ‬ ‫ﻣﻨﺎﻓﺬ دﺧﻞ‪/‬ﺧﺮج‬

‫ﻋﺪد ‪6‬‬ ‫ﻣﻨﺎﻓﺬ ‪USB‬‬ ‫اﻝﻠﻮﺡﺔ اﻝﺨﻠﻔﻴﺔ‬

‫ﻋﺪد ‪6‬‬ ‫ﻣﻘﺒﺲ ﺹﻮت‬

‫ﻋﺪد‪2‬‬ ‫ﻣﻨﻔﺬ‪eSATA‬‬

‫‪ATX‬‬ ‫‪ 244‬ﻣﻢ )ﻋﺮض( ‪ 305 X‬ﻣﻢ )ارﺗﻔﺎع(‬ ‫ﺡﺠﻢ اﻝﻠﻮﺡﺔ‬

‫ﺏﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻝﺔ اﻝﺪﻋﻢ ﻷي ﻥﻈﺎم ﺕﺸﻐﻴﻞ ﺏﺈﺧﻄﺎر ‪Biostar‬ﺕﺤﺘﻔﻆ‬

‫‪Windows 2000 / XP / VISTA‬‬ ‫دﻋﻢ أﻥﻈﻤﺔ اﻝﺘﺸﻐﻴﻞ‬
‫أو ﺏﺪون إﺧﻄﺎر‪.‬‬

‫‪67‬‬
Motherboard Manual

JAPANESE
仕様

LGA 775
Execute Disable Bit / Enhanced Intel SpeedStep® /
Intel Core2Duo / Core2Quad /
CPU Intel Architecture-64 / Extended Memory 64
Pentium Dual-Core / Celeron Dual-Core /
Technology / Virtualization Technologyをサポートします
Celeron 4xx processor

FSB 800 / 1066 / 1333 / 1600 MHz

Intel P45
チップセット
Intel ICH10R

DDR2 DIMMスロット x 4
デュアル チャンネルモードDDR2メモリモジュール
各DIMMは 256MB / 512MB / 1GB / 2GB
メインメモリ DDR2 1066 / 800 / 667をサポート
DDR2をサポート
登録済みDIMMとECC DIMMはサポートされません
最大メモリ容量8GB

Fintek F71887F 環境コントロールイニシアチブ、

もっとも一般に使用されるレガシーSuper I/O H/Wモニター

Super I/O
機能を採用しています。 ファン速度コントローラ/ モニター

低ピンカウントインターフェイス ITEの「スマートガーディアン」機能

Ultra DMA 33 / 66 / 100 / 133バスマスタモード

IDE Marvell 88SE6121
PIO Mode 0~4のサポート

最高3 Gb/秒のデータ転送速度

SATA II ICH10R SATAバージョン2.0仕様に準拠。

RAID 0 / 1 / 5 / 1+0のサポート

最高3 Gb/秒のデータ転送速度

eSATA Marvell 88SE6121 SATAバージョン2.0仕様に準拠。

RAID 0,1 /Port-Multiplierのサポート

10 / 100 / 1000 Mb/秒のオートネゴシエーション

LAN Realtek RTL 8111C
半/全二重機能

HDオーディ ハイデフィニションオーディオのサポート
ALC888S
オのサポート 7.1 チャンネルオーディオアウト

PCIスロット x2

PCI Express Gen2 x16スロット

(x16/x8) x1
スロット
PCI Express Gen2 x16スロット

(x8) x1

PCI Express x1スロット x2

68
 TPower I45
仕様

フロッピーコネクタ x1 各コネクタは2つのフロッピードライブをサポートします

シリアルポート x1

IDEコネクタ x1 各コネクタは2つのIDEデバイスをサポートします

SATAコネクタ x6 各コネクタは1つのSATAデバイスをサポートします

フロントパネルコネクタ x1 フロントパネル機能をサポートします

フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします

CDインコネクタ x1 CDオーディオイン機能をサポートします

S/PDIFアウトコネクタ x2 デジタルオーディオアウト機能をサポートします
オンボードコ
S/PDIFインコネクタ x1 デジタルオーディオイン機能をサポートします
ネクタ
CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載)

システムファンヘッダ x2 システムファン電源装置

CMOSクリアヘッダ x1

各コネクタは2つのフロントパネルUSBポートをサポートし
USBコネクタ x3
ます

電源コネクタ(24ピン) x1

電源コネクタ(8ピン) x1

電源コネクタ(4ピン) x1

PS/2キーボード x1

PS/2マウス x1

背面パネル LANポート x1

I/O USBポート x6

オーディオジャック x6

eSATAポート x2

ボードサイズ 244 mm (幅) X 305 mm (高さ) ATX

Biostarは事前のサポートなしにOSサポートを追加または削
OSサポート Windows 2000 / XP / VISTA
除する権利を留保します。

2008/04/23

69