DIGITAL MOVEMENT GUIDE ENGLISH

BJ2679 FL137EA MLL033

DZ7187 - DZ7188 DZ5175, DZ5176 DZ5145, DZ5146

BJ2957 FL610AB, MLG367D MLL-045

DZ7196, DZ7208, DZ7209 DZ7118, DZ7119, DZ7120, DZ7091, DZ7092, DZ7109,
(for digital display only) DZ7121, DZ7169 - DZ7172, DZ7110, DZ7162, DZ7176,
DZ7235, DZ7236 DZ7237, DZ7238

BJ3170 FO-001 QAA-006, QAA-033

DZ7153, DZ7156, DZ7157, DZ7206, DZ7207 DZ7095, DZ7096, DZ7097,
DZ7189 - DZ7192 (for digital display only) DZ7098, DZ7105, DZ7106,
(for digital display only) DZ7113, DZ7115, DZ7116,
DZ7117, DZ7189 - DZ7190

F145GR3 FO-002 QBJ2718-AA

DZ7069 - DZ7071, DZ7087, DZ7076, DZ7077, DZ7078, DZ7173 - DZ7175, DZ7195,
DZ7117 DZ7083, DZ7093, DZ7094 DZ7202 - DZ7205

FDT003 G3 & G1 QBJ3101-AA

DZ7006, DZ7043, DZ7046, DZ7122, DZ7123, DZ7124, DZ7177 - DZ7179, DZ7197 -
DZ7142, DZ7143, DZ7144 DZ7152, DZ7154, DZ7155, DZ7201
DZ7180, DZ7184 - DZ7186 (for digital display only)

FL0521 MD-FL298X, FL388, QFL631BA

DZ7099, DZ7100 QFL226DB DZ7162 - DZ7168, DZ7176,
DZ7081, DZ7082, DZ7130 - DZ7218
DZ7136, DZ7145, DZ7146,
DZ7149 - DZ7151, DZ7181 -
DZ7183, DZ7211 - DZ7213

FL075AB MLG-035 ZD0603B01

DZ7033, DZ7034, DZ7066, DZ7107, DZ7108 DZ5173, DZ5174, DZ7079,
DZ7068, DZ7089, DZ7137, DZ7080, DZ7111, DZ7112
DZ7138, DZ7139, DZ7140,
DZ7141, DZ7147, DZ7148

FL137AX
DZ7101 - DZ7103, DZ7125 -
DZ7127, DZ7193, DZ7194,
DZ7214, DZ7221
(for digital display only)

2 / 2011
-1-
IMPORTANT TO KNOW!
• When the watch is underwater or wet, never use the pushers/bezels, or set the time. Watch cases and metal bracelets should be rinsed thoroughly in fresh water after being in salt water.
• No hot tub/sauna. Please do not take your DIESEL watch into the hot tub/sauna. The combination of extreme heat and water may cause your watch to lose some of its water-resistance.
• No backward hand, or date, adjustments should be made when the analog hands read between 8pm and 3am. At these times, the gears are too close together and such a change could
cause damage.
• Tighten screwlock crown completely.
• Always set the crown in the normal position.

RESISTANCE TO WATER
Depth WATER-RESISTANT 3 BAR (30 M) WATER-RESISTANT 5 BAR (50 M) WATER-RESISTANT 10 BAR (100 M)

Caseback marking 3 ATM 5 ATM 10 ATM

Light spray, perspiration, light rain, etc. OK OK OK

Bathing, etc. NO OK OK

Swimming, etc. NO NO OK

Skin diving (diving without oxygen cylinder) NO NO OK

Water-resistant characteristics Normal daily water contact. Suitable for bathing, but cannot be worn for swimming or diving. Suitable for skin diving.

Automatic Winding Movements

A timepiece with an automatic winding movement obtains the power to wind itself by the movement of your wrist, there is no battery. Therefore, not wearing the timepiece for several consecutive days
could exhaust the power reserve. If your watch stops, it is recommended that you manually wind the movement by rotating the crown clockwise to achieve the necessary power reserve.

It is important that your timepiece is adjusted to match the size of your wrist. A loose fit may result in a loss in capacity of the timepiece to wind itself. When fully wound, your timepiece has a power
reserve of approximately 38 hours.

Automatic 6T51
1. To start time-keeping, rotate the crown clockwise 15-20 times in position 1.
2. Pull crown out to position 2 and rotate clockwise to set time. Push crown back to position 1. (1) (2) (3)
3. Pull crown out to position 2. Then pull crown out from position 2 to position 3 to advance date by one day. Each time the
DATE
crown is pulled from position 2 to position 3 the date is advanced by one increment. Return crown to position 1.

TV Automatic Movement
WINDING HOUR HAND MINUTE HAND

With the crown in the position 1, turn the crown 15-20 times and the movement will start after shaking the watch slightly.
After approximately 40-42 hours, the timepiece will need to be wound.
(1) (2) (3)

SETTING THE TIME SECOND HAND DATE

1. Pull crown out to position 2.
2. Turn crown to set hour and minute hands.
3. Push crown back to position 1.

SETTING THE DATE

1. Pull the crown to position 2.
2. Pull the crown from position 2 to position 3, then date advance one day.
3. After the date has been set, push the crown back to position 1.

Automatic Winding Movement 8215

HOUR HAND MINUTE HAND
WINDING
With the crown in the position 1, turn the crown 15-20 times and the movement will start after shaking the watch slightly.
After approximately 40-42 hours, the timepiece will need to be wound.
(1) (2) (3)

SETTING THE TIME SECOND HAND DATE

1. Pull the crown out to position 3.
2. Turn the crown to set the hour and minute hands.
3. Push the crown back to position 1.

SETTING THE DATE

1. Pull the crown out to position 2.
2. Turn the crown counter-clockwise to set the date.
3. Push the crown back to the position 1.

-2-
Date Watch GL10, IS13, VJ32A11, VJ32A31, 9T13, 505.2-3, 515.1-3, 515.2-3, 585.2, 715-2, 2115, 2315
Date Setting
1. Pull the crown out to position 2.
2. Turn counter-clockwise and set the date for the previous day. (1) (2) (3)

DATE
Time Setting
1. Pull crown out to setting 3.
2. Turn counter-clockwise to advance the time and continue until the day/date changes to the present day.
3. Set the correct time.
4. Push crown back to position 1.

Day/Date Watch IS02, 507.2-3, 517.2, 2105, 2305, 2405

DAY
Date Setting
1. Pull the crown out to position 2.
2. Turn clockwise and set the date for the previous day. (1) (2) (3)

DATE
Day Setting
With crown still in position 2, turn counter-clockwise and set the day for the previous day.

Time Setting
1. Pull crown out to setting 3.
2. Turn counter-clockwise to advance the time and continue until the day/date changes to the present day.
3. Set the correct time.
4. Push crown back to position 1.

3 Hand with EL Watch 6N30/OU30

EL BUTTON
EL FUNCTION
The EL (light-up) button is located above the crown. Pressing it once will activate the light-up function of the display making the
display face visible in low-light situations for 3 seconds. CROWN

DZ1065 and DZ1066 hold rights covered under U.S. Patent numbers: 6,106,127, 6,299,321, and 6,486,561.

Dual Time Watch K62/132 buttonS

Time Setting
1. Push buttons to move hands.
2. Set correct time.

FRONT BACK

Sub-Second 1L45
Time Setting
Pull crown out to position 2 and rotate to set time. (1) (2)

NOTE: When crown is pushed back to position 1, small second hand begins to run.

SMALL SECOND HAND

2 Eye Day/Date Multifunction VX36A1

(1 crown) DATE

DAY
DATE SETTING
1. Pull crown out to position 2. (1) (2) (3)
2. Turn clockwise to advance date hand.
3. Push crown back to position 1.

DATE AND TIME SETTING

1. Pull crown out to position 3.
2. Turn clockwise to advance hour and minute hands.
The hand showing days of the week will also move with the hour and minute hands. Keep turning until you have
reached the desired day.

-3-
Two Eye Multifunction 6P25, 6P75
Date Setting DATE DATE
1. Pull crown out to position 2.
2. Turn counter-clockwise to select date.
(1)(2) (3) (1)(2) (3)
DAY DAY
Day and Time Setting
1. To set time, pull crown out to position 3.
2. Turn clockwise to set hour and minute hands. The hand showing days of the week will also move with the hour and minute
hands. Keep turning until you have reached the desired day.
3. Push crown back to position 1.

Multifunction 6P27
DATE

TIME AND WEEKDAY SETTING

DAY
1. Pull crown out to position 3, stopping the second hand at 12 o’clock.
2. Turn crown clockwise to set weekday (hour, minute, and 24-hour hands will also move). (1) (2) (3)

Note: Do not set the day by turning the crown counter-clockwise, or the date may not change correctly. 24-HOUR HAND
3. Turn hour and minute hands clockwise to set the time. To ensure the time is set accurately, first turn the minute-hand 5
minutes ahead of the correct time, then turn back (counter-clockwise) to the correct time.
4. Return crown to position 1.
Note: Make sure you have correctly set AM/PM time by checking the 24-hour hand.

DATE SETTING
1. Pull crown out to position 2.
2. Turn crown counter-clockwise to set date.
Note: Do not set the date between 9:00 p.m. and 12:30 a.m. or the date may not change correctly.

Three Eye Multifunction VX3J

(1 crown)
DAY
Date Setting
1. Pull crown out to position 2.
(1) (2) (3)
2. Turn clockwise to advance the date hand.
3. Push crown back to position 1. 24-HOUR DATE

Day and Time Setting

1. Pull crown out to position 3.
2. Turn clockwise to advance hour and minute hands.
The hand showing days of the week will also move with the hour and minute hands. Keep turning until you have
reached the desired day.

24-Hour Sub-Dial Setting

The 24-hour hand moves correspondingly with the hour and minute hands. When setting the time be sure to check that the
24-hour hand is set properly.

Chronograph 5020B
(1 crown/2 pushers) CHRONOGRAPH SECOND HAND
(A)
SECOND HAND
DATE AND TIME SETTING CHRONOGRAPH HOUR
1. Pull crown out to position 2. AND MINUTE HANDS
(1) (2) (3)
2. Turn counter-clockwise and set the date for the previous day.
3. Pull crown out to position 3. All chronograph hands will return to zero position. Do not return the crown to its normal DATE (B)
position while the hand is returning to zero, or else the position the hand is in when this is done will be recognized as the
new zero position.
4. Turn crown clockwise until correct date is displayed in date window.
5. Turn crown to set the time.
6. Return crown to position 1.

CHRONOGRAPH OPERATION
1. Push A to start/stop the chronograph.
2. Push B to reset the chronograph.

SPLIT TIME MEASUREMENT

1. Press B while the chronograph is running; timing will continue in background.
2. Press B again to start the next interval; the three chronograph hands will advance to the ongoing measured time.
3. Press A to stop chronograph.
4. Press B to reset.

CHRONOGRAPH ZERO RESET

1. Pull crown out to position 3.
2. Press and hold A and B simultaneously for 2 seconds until chronograph second hand rotates around the dial.
3. Press A to reset the chronograph second hand to 12:00 (zero) position. Each press advances the chronograph second hand
one mark. If A is held down for over 2 seconds, the chronograph second hand advances continuously.
4. Press B to set and advance to the chronograph minute and hour hands.
5. Repeat step 3 to reset chronograph minute and hour hands.
6. Return crown to position 1 when chronograph hands are reset to zero.

-4-
Chronograph Stopwatch OS10 (no date - OS30)
(1 crown/2 pushers) MINUTE HAND
(A)

TIME SETTING HOUR HAND

1. Pull crown out to position 3. (1) (2) (3)
2. Turn crown to set the desired time. (B)
SECOND HAND
3. Return crown to position 1.

DATE SETTING
1. Pull crown out to position 2.
2. Turn crown counter-clockwise until the correct date is shown in the date window.
3. Return crown to position 1.

CHRONOGRAPH OPERATION
1. Press A to start/stop the chronograph.
2. Press B for reset.

ADJUSTING THE CHRONOGRAPH

1. Pull crown to position 3.
2. Press A to reset the second hand to “0.”
3. Press B to reset the chronograph minute and hour hands.
4. Reset the watch to the current time and return crown to position 1.

Chronograph with Date OS20, FS00, FS20

(1crown/2pushers) CHRONOGRAPH
SECOND HAND (A)
24 HOUR HAND
TIME SETTING
CHRONOGRAPH
1. Pull crown out to position 3. Chronograph second hand will return to zero position. Do not return the crown to its normal MINUTE HAND
(1) (2) (3)
position while the hands are returning to zero, or else the position the hands are at when this is done will be recognized as
the new zero position. SECOND HAND (B)
2. Turn to set hour, minute and 24 hour hands.
3. Return crown to position 1. DATE

DATE SETTING
1. Pull crown out to position 2. (A)
2. Turn clockwise to set the date.
3. Return crown to position 1.
(1) (2) (3)

CHRONOGRAPH OPERATION
(B)
1. Push A to start/stop the chronograph.
2. Push B to reset the chronograph.

CHRONOGRAPH ZERO RESET

1. Pull crown out to position 3.
2. Press A to set the chronograph second hand to 12:00 (zero) position. Each press advances the chronograph second hand
one mark. If A is held down for over 2 seconds, the chronograph second hand advances continuously.
3. Return crown to position 1.

Chronograph JS15, JS25, JS26

24-HOUR HAND
TIME AND DATE SETTING (A)

1. Pull crown out to position 2. CHRONOGRAPH

2. Rotate crown clockwise until the previous day’s date is shown in the date window. MINUTE HAND
(1) (2) (3)
3. Pull crown out to position 3.
CHRONOGRAPH (B)
4. Rotate crown clockwise until the correct date is shown in the date window. SECOND HAND
5. Continue to rotate crown to set correct am/pm time.
NOTE: 24-hour hand moves correspondingly with the hour and minute hands. When setting the time be sure to
check that the 24-hour hand is set properly.
6. Return crown to position 1.
NOTE: When the crown is in position 2, do not press the pushers. Otherwise the chronograph hands will move. CHRONOGRAPH
MINUTE HAND (A)
NOTE: Do not set the date between 9:00 p.m. and 1:00 a.m. to ensure accuracy.

CHRONOGRAPH (1) (2) (3)

1. Press A to start/stop the chronograph.
(B)
2. Press B to reset to zero. CHRONOGRAPH
SECOND HAND 24-HOUR HAND

CHRONOGRAPH ZERO RESET

1. If either of the chronograph hands is not at the zero (12:00) position, pull crown out to position 3.
2. Press A to move hands clockwise; press B to move hands counter-clockwise. Each press of A or B will move the
chronograph hands by one increment/decrement. Or press and hold A or B for fast increment/decrement.
3. When both hands are in the zero position, reset time and return crown to position 1.
NOTE: Chronograph minute hand will synchronize with chronograph second hand during chronograph zero reset.

-5-
Chronograph OS60
(1 crown/2 pushers) MINUTE
HAND (A)
HOUR
SETTING THE TIME HAND
1. Pull the crown out to position 3. Chronograph second hand and 1/20 second hand will return to zero position. Do not return (1) (2) (3)
the crown to its normal position while the hands are returning to zero, or else the position the hands are at when this is (B)
1/20
done will be recognized as the new zero position. SECOND HAND
2. Turn the crown to set the desired time.
3. Return the crown to its normal position.

SETTING THE DATE

1. Pull the crown out to position 2.
2. Turn the crown counter clockwise until the correct date is shown in the date window.
3. Return the crown to its normal position.

CHRONOGRAPH ZERO RESET

1. Pull the crown out to position 3. Chronograph second hand and 1/20 second hand will return to zero. Do not return the
crown to its normal position while the hands are returning to zero. Doing so will cause the position of the hands to be
recognized as the new zero position.
2. Push (A) to set the chronograph second hand to 12:00 (zero) position. Each press of (A) advances the chronograph second
hand one mark. If (A) is held down for over 2 seconds, the chronograph second hand advances continuously.
3. Push B to set the chronograph 1/20 second hand to 12:00 (zero) position. Each press of (B) advances the 1/20 second
hand one mark. If (B) is held down for over 2 seconds, the 1/20 second hand advances continuously.
4. Return crown to its normal position.
5. Press (B) to reset all hands to the zero position.

CHRONOGRAPH OPERATION
1. Push (A) to start/stop the chronograph.
2. Push (B) to reset the chronograph.
3. When the measured time is over 30 seconds, the 1/20-second hand stops; however, the watch continues measuring the
elapsed time. The exact time elapsed is indicated when A is pressed to stop the chronograph, and the 1/20-second hand
moves to the actual time. The hand returns to the “0” position when B is pressed and the chronograph is reset.
4. If (B) is pressed again after chronograph is reset, the 1/20-second hand changes to measure each second.

Chronograph Stopwatch VD55B, VD57B

(1 crown/2 pushers) 1/10 SECOND HAND
(A)

Time Setting MINUTE HAND

1. Pull crown out to position 3. (1) (2) (3)
2. Set time by turning the crown clockwise. (B)
3. Push back to position 1 to start the watch. SECOND HAND

Using the Stopwatch

1. Press A to start/stop the stopwatch.
2. Press B to control the split time and reset.

Stopwatch Hand Adjustment

1. Pull crown out to position 3.
2. Press A to reset the stopwatch 1/10 second hand to the “0” position.
3. Press B to reset the second and minute hands. The hands only move clockwise.
4. With each press of A or B, the hands move one position. They move quickly if the buttons are kept pressed.

Note: If the stopwatch hands function improperly, pull out crown and press A and B at the same time for over 2
seconds. When the buttons are released, the stopwatch second and 1/10 second hands will spin around and
return to “0.” This will indicate that the internal circuit has been reset.

Date Setting (on some models only)

1. Pull crown out to position 2.
2. Turn clockwise until desired date appears in window.
3. Push crown back to position 1.

-6-
Chronograph ISA 8161/202 MINUTE HAND
(1 crown/2 pushers) (A)
SECOND HAND

Setting the time

(1) (2) (3)
1. Pull crown out to position 3.
(B)
2. Set time by turning the crown.
DATE
3. Push the crown back to position 1.

Setting the Date

1. Pull crown out to position 2.
2. Set date by turning the crown.
3. Push the crown back to position 1.

Resetting Chronograph (after battery exchange or mishandling only)

1. Press both A and B pushers at the same time.
2. Next press B to reset the minutes.
3. Then press A to reset seconds.
4. To exit press both A and B pushers at the same time.

Measuring Cumulative Times

1. Press A pusher to start.
2. Press A pusher to stop.
3. Press B pusher to reset.

Measuring Split Times

1. Press A pusher to start.
2. Press B pusher to split.
3. Press B pusher to restart.
4. Press A pusher to stop.
5. Press B pusher to reset.

Chronograph ISA 8171/201

Time and date setting
1. Pull crown out to position 2. Chronograph
1/5 second hand (A)
2. Rotate crown clockwise until the previous day’s date is shown in the date window. SECOND HAND
3. Pull crown out to position 3.
Chronograph
4. Rotate crown clockwise until the correct date is shown in the date window. minute hand
(1) (2) (3)
5. Continue to rotate crown to set correct am/pm time.
6. Return crown to position 1. Date (B)
Note: Do not set the date between 9:00 p.m. and 12:30 a.m. to ensure accuracy.

Chronograph operation
1. Press A to start/stop the chronograph.
2. Press B to restart/reset.
Note: After 2 hours of continuous running, the chronograph will automatically stop and reset to save the battery.

Split time
1. Press B while the chronograph is running.
2. Press B again to return to the chronograph.
3. Press A to finalize timing.
4. Press B to reset.

Chronograph zero reset

1. If either of the chronograph hands is not at the zero (12:00) position, pull crown out to position 2.
2. Press B to reset chronograph minute hand. Each press of B will advance the chronograph minute hand by one increment or
press and hold B for fast advance.
3. Press A to reset chronograph 1/5 second hand. Each press of B will advance the chronograph 1/5 second hand by one
increment or press and hold B for fast advance.

-7-
Chronograph Stopwatch VD54 (with date - VD53)
(1 crown/2 pushers)
(A)
24-HOUR HAND
Time and Date Setting
1. Before setting the time, make sure the chronograph is stopped and set to zero (12:00) position. MINUTE HAND
(1) (2) (3)
2. Pull crown out to position 2.
3. Turn crown clockwise until the previous day’s date is displayed. SECOND HAND (B)
4. Pull crown out to position 3 when the second hand is at the 12:00 position.
5. Turn crown to set time.
Note: 24-hour hand moves correspondingly with the hour and minute hands. When setting the time be sure to
check that the 24-hour hand is set properly.
6. Return crown to position 1.
Note: When the crown is in position 2, do not press the pushers. Otherwise the chronograph hands will move.

Chronograph
1. Press A to start/stop the chronograph.
2. Press B to reset to zero.

Split Time
1. Press B while the chronograph is running.
2. Press B again to return to the chronograph.
3. Press A to finalize timing.
4. Press B to reset.

Chronograph Zero Reset

1. If either of the chronograph hands is not at the zero (12:00) position, pull crown out to position 3.
2. Press A to move hands clockwise; press B to move hands counter-clockwise.
3. Return crown to position 1.

Digital BJ3170
Normal Time Display
(A)
1. Press A to change mode. Mode sequence is: normal time, chronograph, alarm, time setting.
2. Press B to display alarm.
3. Press C to display date.
4. Press A+B to toggle chime on/off (all days of the week will display for “on”).
5. Press B+C to toggle alarm on/off. Alarm will sound for 60 seconds; press B to silence alarm or press D for snooze function (B)
(alarm will sound 5 minutes later).

Chronograph Mode
1. Press A to change to chronograph mode.
(C)
2. Press C to start/stop the chronograph.
3. Press B when the chronograph is stopped to reset.
Note: When the chronograph is running, press A to return to normal time display. Chronograph will continue to
count time.

Split Time
1. Press B while the chronograph is running.
2. Press C to finalize timing.
3. Press B to display all counts.
4. Press B again to reset.

Alarm Mode
1. Press A to change to alarm mode; hour will begin flashing.
2. Press C to increase digits; press and hold C for fast advance.
3. Press B to advance to minutes.
4. Press C to increase digits; press and hold C for fast advance.
5. Press B to save data.
6. Press A to exit and return to normal time display.

Time And Date Setting

1. Press A to change to time setting mode; seconds will begin flashing.
2. Press C to reset seconds to zero.
3. Press B to advance to minutes.
4. Press C to increase digits; press and hold C for fast advance.
5. Press B to set and advance to next setting value.
6. Setting sequence is: seconds, minute, hour, date, month, weekday.
Note: When setting the hour, “H” will display for 24-hour format, “A” or “P” will display for 12-hour format.

-8-
Digital FL137AX / FL137EA / FL137AB SIMPLE ANALOG SIMPLE ANALOG
(1 crown) (1 crown)
NORMAL TIME DISPLAY
1. Press A to change display. Display sequence is time, calendar, seconds.
2. Press B to toggle 12/24-hour format.

TIME AND DATE SETTING (A) (B)

1. Press and hold B for 2 seconds to enter setting mode; year will begin flashing.
DIGITAL
2. Press A to advance digit; press and hold A for fast advance. FL137AX
3. Press B to set and advance to next setting value. Digital FL137AX (2 pushers)
4. Setting sequence is year, month, date, hour, minute.
5. Press B to exit setting mode.
Note: Hour will be displayed in 24-hour format in time setting mode. (A) (B)
Note: If no pusher/button is operated for 30 seconds, all changes will be saved and the
setting will automatically return to display mode.

Digital FL137EA

Ana-Digi FL052I
NORMAL TIME DISPLAY
1. Press A to change mode. Mode sequence is: normal time, world time, alarm, chronograph,
(B) (C)
memory recall, timer.
2. Press B for EL.
3. Press C to toggle chime on/off.
4. Press D to toggle DST on/off for the selected city.
5. In any mode or setting, if no pusher is operated for 60 seconds, setting will be returned to (A) (D)
normal time display.

TIME AND CALENDAR SETTING

1. Press and hold B for 2 seconds to enter setting mode. 12/24-hour time will begin flashing.
2. Press C to select 12/24-hour time.
3. Press A to set and advance to seconds.
4. Press C to reset seconds to zero.
5. Press A to set and advance to minute. ALARM SETTING
6. Press C to increase the digit; press D to decrease the digit. 1. Press and hold B for 2 seconds to enter setting mode; minutes will begin flashing.
7. Press A to set and advance to next setting value. 2. Press C to increase the digit; press D to decrease the digit.
8. Setting sequence is: 12/24-hour format, seconds, minute, hour, year, month, date, and city. 3. Press A to set and advance to hour.
9. Press B to exit setting mode. 4. Press C to increase the digit; press D to decrease the digit.
Note: Weekday will automatically update upon exiting setting mode. 5. Press B to exit setting mode.
Note: Alarm is automatically turned on when setting is changed.
WORLD TIME MODE
1. Press A to change to world time mode. CHRONOGRAPH MODE
2. Press C to select city. 1. Press A to change to chronograph mode.
3. Press D for DST on/off for the selected city. 2. Press C to start the chronograph; press D to stop the chronograph.
3. Press D again to reset.
Hour Hour
Words City Words City
Difference Difference SPLIT TIME
1. Press C while the chronograph is running for split time (will record up to 20 laps).
MDY Midway -11 hours PAR Paris +1 hour
2. Press D to finalize timing.
HNL Honolulu -10 hours CAI Cairo +2 hours
ANC Anchorage -9 hours MOW Moscow +3 hours
LAX Los Angeles -8 hours DXB Dubai +4 hours MEMORY RECALL MODE
DEN Denver -7 hours KHI Karachi +5 hours 1. Press A to change to recall mode when information is recorded in the chronograph.
CHI Chicago -6 hours DAC Dacca +6 hours 2. Press C to view next lap; press D to view previous lap.
NYC New York -5 hours BKK Bangkok +7 hours
CCS Caracas -4 hours HKG Hong Kong +8 hours TIMER MODE
RIO Rio de Janeiro -3 hours TYO Tokyo +9 hours 1. Press A to change to countdown timer mode.
-2H -2H -2 hours SYD Sydney +10 hours
2. Press C to start/stop the timer.
-1H -1H -1 hour NOU Noumea +11 hours
LON London 0 hours AKL Auchland +12 hours 3. Press D to reset the timer when it is not running.
4. Timer will sound for 30 seconds upon reaching zero; press any pusher to silence alarm.

ALARM MODE TIMER SETTING

1. Press A to change to alarm mode. 1. Press and hold B for 2 seconds to enter setting mode; seconds will begin flashing.
2. Press C to scroll through alarms (3 alarms). 2. Press C to increase digit; press D to decrease digit.
3. Press D to toggle alarm on/off. 3. Press A to set and advance to next setting value.
4. Alarm will sound for 30 seconds; press any pusher to silence alarm. 4. Setting sequence is: seconds, minutes, hours.

-9-
Digital FL291
OVERVIEW
Features include TIME/DATE, CHRONO, TIMER, ALARM, and LIGHT-UP EL. (A) (C)

LIGHT-UP EL
Press (A) to activate light-up function for 3 seconds.

TIME OF DAY MODE

(B) (D)
- To set Time, press (B) until hour flashes. Use (C) and (D) buttons to select hour. Press (B) to advance. Press and hold (B) to
complete set mode.
- Press (C) to view the Time and Date Display.
- Press and hold (C) to change the time from 12 hour to 24 hour.
- Press (D) to toggle hourly chime.
Hourly chime/Key tone
CHRONO MODE Alarm enable/disable
- Press (C) to start time. Press (D) to stop time. Press (C) twice to enable split time. Press (D) to stop time.
Chrono icon
- Press and hold (D) to reset CHRONO mode.
Timer icon
TIMER MODE
- To set TIMER, press and hold (B) until hour flashes. Use (C) and (D) Buttons to select hour. Press (B) to advance to minutes/
seconds. Press and hold (B) to complete TIMER mode.
- Press (C) to start TIMER.
- 10 Beeps will be sounded when timer value reaches zero.

ALARM MODE
- To set ALARM, press and hold (B) until hour flashes. Use (C) and (D) Buttons to select hour. Press (B) to advance to minutes.
Press and hold (B) to set ALARM mode.
- Press (D) to toggle alarm.
- ALARM will sound for 20 seconds.
- Press any button to stop ALARM.

BUTTONS
MODE OPERATION A B C D
LIGHT MODE START/SPLIT RESET/STOP

PRESS ONCE EL CHRONO TOGGLE TIME/DATE CHIME ON/OFF

TIME OF DAY
PRESS AND HOLD – SETTING TIME FORMAT –

PRESS ONCE EL TIMER START/SPLIT STOP

CHRONO
PRESS AND HOLD – – – RESET

PRESS ONCE EL ALARM START STOP

TIMER
PRESS AND HOLD – SETTING – RESET

PRESS ONCE EL TIME OF DAY – ALARM ON/OFF

ALARM
PRESS AND HOLD – SETTING – –

PRESS ONCE EL NEXT FIELD INCREMENT DECREMENT

SETTING
PRESS AND HOLD – CONFIRM/EXIT FAST INCREMENT FAST DECREMENT

NOTE:
- Analog time and digital time may not be in sync.
- The key tone enable/disable will be dependent on the HOURLY CHIME enable/disable status.

Digital FO-001
(A)
NORMAL TIME DISPLAY
Press A to change display. Display sequence is normal time, date, seconds.
(B)
TIME AND CALENDAR SETTING
1. In normal time display, press B twice; month will begin flashing.
2. Press A to increase digits.
3. Press B to advance to next setting value.
4. Setting sequence is: month, date, hour, and minute.
5. Press B to exit setting mode.
NOTE: At any point in setting mode, press A to exit setting mode and return to normal time display.

- 10 -
Digital FDT003 / BD3000
Alarm Version FDT003 / BD3000 Mode Icon Legend
OVERVIEW D
B TIME 1,2 ALARM
This instruction book is set-up to mirror the logic of the digital module. The features DUAL CHRONO
Week,1,2
TIME, ALARM, CHRONOGRAPH and TIMER are described in the order they appear as in the C COUNTDOWN
ALARM
module. Therefore almost all setting instructions fall under the OPTIONS section. Each mode OPTIONS
A mode icon/on TIMER
of operation is covered in detail below; however, there are a number of unique innovations E
that need to be explained first. AUTO EL Hourly chime on

LIGHT-UP EL
The EL (light-up) button is (C). Pressing it once will activate the light-up function of the Time 1 display Time 2 display
display making the display face visible in low-light situations for 3 seconds. Press and hold the EL button for 2 seconds and the AUTO EL function
is turned on, marked by the Auto EL icon. This function enables the EL to be activated with the pressing of any function buttons. To turn this Alarm Weekday display
function off, press and hold the EL button again for 2 seconds.

DUAL TIME
Set two different time zones and move easily between the two by pressing button (A) while in Time mode, alarms switch over accordingly. Under
T2 setting, no 12/24 hour mode adjustment.

ALARM
Alarm-week is a daily reminder Monday through Sunday. Alarm Weekday display Alarms 1,2 display
Alarms 1 and 2 may be used for one time or as repeat reminders:
One Time Reminder:
To use as a one-time reminder, simply set all the data fields for the specific time, date, & month.
Repeat Daily Reminder:
To use the repeat reminder for the same time every day, simply fill in the time field only, leaving the date, and month field empty (--). The reminder
will repeat at the same time every day.
Repeat Date Reminder:
To use the repeat reminder for the same calendar date every month, simply fill in the date and time fields only, leaving the month field empty (--).
The reminder will repeat on the same calendar date & time every month. Alarms 1,2 display
Alarms are automatically turned on after setting. To interrupt any alarm while sounding, press any button.
Alarms on/off:
The Alarm mode can be accessed by repeatedly pressing (B) till the Alarm icon is activated. Chronograph display
1. To confirm an alarms settings press (A) to advance through them.
2. To turn an alarm “on/off,” press (D) while that alarm is displayed, the word “on” will appear.
3. Press (D) again to turn the alarm “off,” and (--) will appear.

CHRONOGRAPH
The smallest measure of time it can measure is 1/100th of a second and the largest is 9 hours, 59 minutes, 59 seconds, and 99 1/100th of a
second. The chrono will keep on timing after this measurement, however the hour counter will reset to “0.” The Chrono mode can be accessed by
repeatedly pressing (B) till the Chrono icon is activated.

START/STOP TIMING
1. To begin timing press (D), the chronograph will begin timing.
3:00 Timer display FREE Timer display
2. To stop timing press (D), while the chronograph is stopped you may resume timing by pressing (D) or reset to “0:00:00:00” by pressing (E).

TIMER
This module has a countdown mode with 3 preset times: 3 minutes, 5 minutes, and 10. In addition to the preset timers, there is one FREE space
for the user to set and store a custom timer setting. The timer will measure in increments of 1 second. Set the countdown timer anywhere
between 5 seconds and 9 hours 59 minutes and 59 seconds. Upon reaching “0” the countdown timer will reset and begin counting down again
automatically, keeping track of the number of times it does so with the repeat counter (up to 99 times). Any timer set will continue to countdown
repeatedly for 14-15 hours before stopping and resetting itself.
1. To begin timing press (D), the timer will begin timing.
2. To stop timing press (D), while the timer is stopped you may resume timing by pressing (D) or reset the timer to its start value by pressing (E).
Options display
OPTIONS MODE
This module has an additional mode within which all the module settings can be adjusted not unlike a television or VCR. The OPTIONS mode can be
accessed by repeatedly pressing (B) till the Options icon is activated.
1. While in Options mode press (D) to scroll up through the menu and (E) to scroll down through the menu.
2. Press (A) to select the highlighted menu item. This process is repeated throughout the Options menu selections. If at anytime you desire to
return to a previous menu press (B). By pressing and holding (B) for 3 seconds you will exit the Options mode and go directly to TIME mode.

SETTING TIME/DATE
1. Press (B) till Options icon is activated. Press either (D) or (E) till “Tm/Dt” is highlighted, press (A) to select. The Time 1, 2 icons will begin to
flash. (see Fig. 1) Figure 1 Figure 2
2. Press (D) or (E) to highlight either Time 1 or 2, “Tm1 or Tm2” and press (A) to select. Either the Time 1, 2 icon will begin to flash depending
on your selection.
3. The Time default view will display with the SECONDS flashing while setting “T1” and begin with minutes flashing while setting “T2”. To reset
the seconds to “00” press (D). Press (A) to select and advance to the MINUTE setting.
4. Pressing (D) will “+” the minute while pressing (E) will “–” the minute. Press (A) to select and advance to the HOUR setting.
5. Pressing (D) will “+” the hour while pressing (E) will “–” the hour. Press (A) to select and advance to the MONTH setting.
6. Pressing (D) will “+” the month while pressing (E) will “–” the month. Press (A) to select and advance to the DATE setting.
7. Pressing (D) will “+” the date while pressing (E) will “–” the date. Press (A) to select and advance to the YEAR setting. (see Fig. 2)
8. Pressing (D) will “+” the year while pressing (E) will “–” the year. Press (A) to select and advance to the 12/24 HOUR setting.
9. Press (D) or (E) to highlight either 12 or 24 hour mode, “12H or 24H” and press (A) to select. (see Fig. 3) At this point blinking seconds will Figure 3
appear again on the display and you may go through and change any of the settings again or press (B) to EXIT and return to the “Tm1, Tm2”
menu. Pressing (B) again will take you back to the Options menu.
REMEMBER if you press and hold (B) at anytime during the above operation, any settings you have made will be saved and you will go
back to TIME mode.

~ continued on next page ~

- 11 -
CHIME Figure 1 Figure 2
When Chime is “on,” your watch will chime once on the hour every hour: A chime will also accompany mode changes, with a higher pitched chime
signaling the TIME mode.
1. To set Chime “on or off,” press (B) till Options is activated. Press either (D) or (E) till “Alrms” is highlighted, press (A) to select.
2. Press either (D) or (E) till “Chime” is highlighted, press (A) to select. The Chime icon will activate indicating that the chime is on. (see Fig. 1)
3. Press (A) again to turn chime off.

SETTING ALARMS
1. Press (B) till Options icon is activated. Press either (D) or (E) till “Alrms” is highlighted, press (A) to select (see Fig. 2). The Alarm W, 1, 2
icons will begin to flash.
2. Press either (D) or (E) to highlight, Alarm Weekday, 1 or 2, “AL-wk, AL-1 or AL-2” and press (A) to select. Either the Alarm W, 1, or 2 icon will begin to flash
depending on your selection.
Alarm Weekday display

ALARM- WEEK, “AL-wk”

1. Pressing (D) will “+” the minute while pressing (E) will “–” the minute. Press (A) to select and advance to the HOUR setting.
2. Pressing (D) will “+” the hour while pressing (E) will “–” the hour. Press (A) to select. At this point blinking minutes will appear again on the display and you may go
through and change any of the settings again or press (B) to EXIT and return to the “AL-wk, AL-1, AL-2 or Chime” menu. Pressing (B) again will take you back to the
Options menu.
REMEMBER if you press and hold (B) at anytime during the above operation, any settings you have made will be saved and you will go back to TIME mode.

ALARM 1, 2, “AL-1, AL-2”

Alarms 1,2 display
1. Press either (D) or (E) to highlight Alarm 1 or 2, “AL-1 or AL-2” and press (A) to select. Either the Alarm 1, 2 icon will begin to flash depending on your selection.
2. The Alarm 1 or 2 default view will display with the MINUTES flashing. Pressing (D) will “+” the minute while pressing (E) will “–” the minute. Press (A) to select and
advance to the HOUR setting.
3. Pressing (D) will “+” the hour while pressing (E) will “–” the hour. Press (A) to select and advance to the MONTH setting.
4. Pressing (D) will “+” the month while pressing (E) will “–” the month. Press (A) to select and advance to the DATE setting.
5. Pressing (D) will “+” date while pressing (E) will “–” the date. Press (A) to select. At this point blinking minutes will appear again on the display and you may go
through and change any of the settings again or press (B) to EXIT and return to the “AL-wk, AL-1, AL-2 or Chime” menu. Pressing (B) again will take you back to
the Options menu.
REMEMBER if you press and hold (B) at anytime during the above operation, any settings you have made will be saved and you will go back to TIME mode.

TIMER
1. To set the FREE Timer, press (B) till Options is activated. Press either (D) or (E) till “Timer” is highlighted, press (A) to select. The timer icon will begin to flash.
2. The Timer default view will display with the SECONDS flashing. Pressing (D) will “+” the seconds while pressing (E) will “–” the seconds. Press (A) to select 3:00 and
Timeradvance
display FREE Timer display
to the MINUTE setting.
3. Pressing (D) will “+” the minute while pressing (E) will “–” the minute. Press (A) to select and advance to the HOUR setting. Basic view
4. Pressing (D) will “+” the hour while pressing (E) will “–” the hour. Press (A) to select. At this point blinking seconds will appear again on the display and you may go
through and change any of the settings again or press (B) to EXIT and return to the Options menu.
REMEMBER if you press and hold (B) at anytime during the above operation, any settings you have made will be saved and you will go back to TIME mode.

VIEWS, “Views”
This module allows for different display views while in TIME mode. There are (5) five views total to choose from and once set they will remain as the Time view until reset.

BASIC VIEW
This is the default view for the module. It features a prominent time with seconds, day and date. Basic view Dt/Tm view

DATE/TIME, “Dt/Tm”
This view features a prominent month and date, the day and year and current time.

TIME1/TIME2, “T1/T2”
This view features both time zones simultaneously, with emphasis on time 2. The time zone emphasis can be changed by pressing (A) while in Time mode.

TIME ONLY, “Tm”

Dt/Tm view
This view features a large hour, minutes and seconds. While in this view the Dt/Tm view can be accessed by pressing (D). It will display this
alternate view only while (D) is being pressed, once released Time only view returns. T1/T2 view Tm view

SETTING VIEWS
1. Press (B) till Options icon is activated. Press either (D) or (E) till “Views” is highlighted, press (A) to select.
2. Press (D) or (E) to highlight the desired view and press (A) to select, setting the new Time view and returning you to the Options menu.

TIPS, “Tips”
This module features “tips for successful living.” Tips can only be accessed while in Time mode, by pressing (E). The tip will scroll (2) two times
before reverting back to the Time mode display. Repeatedly pressing (E) will scroll through the tips quickly interrupting any currently scrolling tip.
The modules default tips setting is Random, “Rndm,” however there are (2) alternate settings, All and Top10.

RANDOM TIPS, “Rndm”

This setting randomly selects a different tip from the list, with every press of the (E) button while in Time mode. Figure 1
Figure 1

ALL TIPS, “All”

This setting displays the tips in numerical order from the list, with every press of the (E) button while in Time mode.

TOP 10 TIPS, “Top10”

This setting allows you to choose up to 10 of your favorite tips and only select from that list and in the order that you set them with every press of the (E) button while in
Time mode.

SETTING TIPS
Figure 2
1. Press (B) till Options icon is activated. Press either (D) or (E) till “Tips” is highlighted, press (A) to select. (See Fig. 1) Figure 2
2. Press (D) or (E) to highlight either All, Random or Top 10, “All, Rndm or Top10” and press (A) to select.

SETTING TOP 10, “Top10”

1. The Top 10 view will display with the first underscore flashing. (See Fig. 2)
2. Pressing (D) will advance to the “next” Tip while pressing (E) will bring up the “previous” Tip.
3. Press (A) to select and advance to the next Tip setting. This can be repeated for up to 10 tips. At this point the first Tip you set will appear again blinking on the display
and you may go through and change any of the Tip settings again or press (B) to EXIT and return to the “All, Rndm or Top10” menu. Pressing (B) again will take you back
to the Options menu.
REMEMBER if you press and hold (B) at anytime during the above operation, any settings you have made will be saved and you will go back to TIME mode.

- 12 -
Digital FL075AB AM SECOND

DISPLAY MODES
The digital portion of the module has (3) three display views which are selected by pressing (A).
1. While in TIME view, whether in 12 or 24 hour display is irrelevant, press (A) once and the DATE view will appear.
2. To have alternating views between TIME and DATE press (A) a second time and each view will display for 1 second.
3. To return to TIME only view press (A) for a third time.
HOUR MINUTE
SETTING TIME/DATE
1. Press (C) to enter SET mode. The YEAR will begin flashing, press (A) to change the year. This module features an auto TIME DISPLAY MODE
calendar from 2000 to 2050.
DAY
2. Press (C) to advance to the MONTH setting. The month will begin flashing, press (A) to change the month.
3. Press (C) to advance to the DATE setting. The day will begin flashing, press (A) to change the date.
4. Press (C) to advance to the 12hr/24hr setting. The 12h characters will begin flashing, press (A) to change to 24h.
5. Press (C) to advance to the HOUR setting. The hour will begin flashing, press (A) to change the hour.
6. Press (C) to advance to the MINUTE setting. The minute will begin flashing, press (A) to change the minute.
7. Press (C) to advance to the SECONDS reset. The seconds will begin flashing, press (A) to reset to 00. DATE MONTH

8. Press (C) to exit SET mode. SHOWING DATE

Digital MLG367D, FL610AB

NORMAL TIME DISPLAY
1. Press A to change mode. Mode sequence is normal time, alarm, time zone 2, timer,
and chronograph.
2. Press B for EL.
Note: At any point in any setting mode, press D to exit setting mode.
(B) (C)
Note: In any setting mode, if no pusher is operated for 2 minutes, all changes will be
LIGHT START/STOP
saved and the setting will automatically return to display mode.

TIME AND CALENDAR SETTING (A) (D)

1. In normal time display, press D; seconds will begin flashing. MODE LAP/RESET
2. Press C to set seconds to zero.
3. Press A to advance to hour.
4. Press C to advance digit, press and hold C for fast advance.
5. Press A to set and advance to next setting value.
6. Setting sequence is: seconds, hour, minute, year, month, and date.
7. Press D to exit setting mode.
Note: Weekday is automatically updated upon exiting setting mode.
Note: At any point in setting mode, press B to toggle 12/24 hour format.
COUNTDOWN TIMER
ALARM MODE 1. Press A to change to timer mode.
1. Press A to change to alarm mode. 2. Press B to clear countdown and reset timer.
2. Press B to toggle alarm/chime on/off. 3. Press C to start/stop the timer.
3. Alarm will sound at preset time for 20 seconds; press any pusher to silence alarm.
TIMER SETTING
ALARM SETTING 1. Press D to enter setting mode; hour will begin flashing.
1. Press A to change to alarm mode. 2. Press C to advance digit; press and hold C for fast advance.
2. Press D to enter setting mode; hour will begin flashing. 3. Press A to set and advance to next setting value.
3. Press C to advance digit; press and hold C for fast advance. 4. Setting sequence is: hour, minutes, seconds.
4. Press A to set and advance to next setting value. 5. Press D to exit setting mode.
5. Setting sequence is: hour, minutes, month, date. For daily alarm, leave month and date set Note: At any point in setting mode, press B to toggle auto reset on/off. When auto
at “----“ reset is on, timer will automatically re-start upon reaching zero.
6. Press D to exit setting mode.
CHRONOGRAPH MODE
TIME ZONE 2 1. Press A to change to chronograph mode.
1. Press A to change to time zone 2. 2. Press C to start/stop the chronograph.
Note: In time zone 2 display, normal time is shown in the upper portion of the display. 3. Press B to reset to zero.
2. Press D to enter setting mode; hour will begin flashing.
3. Press C to advance digit, press and hold C for fast advance. SPLIT TIME
4. Press A to set and advance to minutes. 1. Press B while the chronograph is running for split time.
5. Press C to advance digit, press and hold C for fast advance. 2. Press B again to return to chronograph.
6. Press D to exit setting mode. 3. Press C to finalize timing.
Note: At any point in setting mode, press B to toggle 12/24 hour format. 4. Press B to reset to zero.

- 13 -
Digital QAA-006, QAA-033
NORMAL TIME DISPLAY
1. Press A for EL. (A)
2. Press B to change mode. Mode sequence is time, time zone 2, alarm, timer.
Note: In any setting mode, if no pusher is operated for 10 seconds, all changes will
be saved and the setting will automatically return to display mode.
(B)

TIME AND DATE SETTING

1. Press and hold A for 3 seconds to enter setting mode; 12/24-hour format will begin flashing.
2. Press B to change 12/24-hour format.
3. Press A to set and advance to seconds.
4. Press B to reset seconds to zero. ALARM SETTING
5. Press A to set and advance to hour. 1. In alarm mode, press and hold A for 3 seconds to enter setting mode; hour will begin
6. Press B to increase digits; press and hold B for fast advance. flashing.
7. Press A to set and advance to next setting value. 2. Press B to increase digit; press and hold B for fast advance.
8. Setting sequence is 12/24-hour format, seconds, hour, minutes, year, month, date. 3. Press A to set and advance to minute.
9. Press A to exit setting mode. 4. Press B to increase digit; press and hold B for fast advance.
Note: Weekday will automatically update upon exiting setting mode. 5. Press A to exit setting mode.

TIME ZONE 2 COUNTDOWN TIMER

1. Press B to change to time zone 2. 1. Press B to change to timer mode.
2. Press and hold A for 3 seconds to enter setting mode; hour will begin flashing. 2. Press A to start/stop the timer.
3. Press B to increase digit; press and hold B for fast advance. 3. When timer reaches zero, alarm will sound for 15 seconds. Press any pusher to silence
4. Press A to set and advance to minutes. alarm.
5. Press B to increase digit; press and hold B for fast advance.
6. Press A to exit setting mode. TIMER SETTING
1. Press and hold A for 3 seconds to enter setting mode; hour will begin flashing.
ALARM MODE 2. Press B to increase digit; press and hold B for fast advance.
1. Press B to change to alarm mode. 3. Press A to set and advance to next setting value.
2. Press and hold B for 3 seconds to toggle alarm/chime on/off. 4. Setting sequence is hour, minute, second.
3. Alarm will sound for 10 seconds. Press any pusher to silence alarm. 5. Press A to exit setting mode.

Digital G1, G3
Normal Time Display
1. Press A to change mode. Mode sequence is normal time, recall, alarm, and countdown timer.
2. Press and hold A 3 seconds to toggle auto EL on/off.
3. Press B for EL.
4. Press C to toggle hourly chime on/off. (B) (C)
5. Press D to flash time zone 2. Press and hold D 3 seconds to toggle normal time display/time
zone 2.
Note: In any mode, press and hold C 3 seconds to change to chronograph mode.
(A) (D)
Note: At any point in any setting mode, press B to exit setting mode.
Note: In any setting mode, if no pusher is operated for 30 seconds, all changes will
be saved and the setting will automatically return to display mode.

Time and Calendar Setting

1. In normal time display, press and hold B 3 seconds; hour will begin flashing.
2. Press C to increase digit; press D to decrease digit. Press and hold C or D for fast
increment/decrement.
3. Press A to set and advance to next setting value. Countdown Timer
4. Repeat steps 2 and 3 through setting sequence. Setting sequence is: hour, minute, second, 1. Press A to change to timer mode. Default setting is 5 minutes.
year, month, date, 12/24-hour format, month/date or date/month format. 2. Press C to start timer; press D to stop the timer.
5. Press B to exit setting mode. 3. Press and hold D 3 seconds to clear the countdown and reset the timer.
6. To set Time Zone 2, press and hold D 3 seconds to change to Time Zone 2. Then use steps Note: Alarm will sound for 20 seconds when countdown reaches zero. Press any
1-5 to set. pusher to silence alarm.
Note: Weekday is automatically updated upon exiting setting mode.
Timer Setting
Recall Mode 1. In timer mode, press and hold B 3 seconds to enter setting mode; hour will begin flashing.
1. Press A to change to recall mode. 2. Press C to increase digit; press D to decrease digit. Press and hold C or D for fast
Note: If no data is stored, display will show NO DATA. If data is saved, display will increment/decrement.
show the current set (1-9). 3. Press A to set and advance to next setting value.
2. Press C to toggle through set data: total time, best time, average time, and each lap (up to 4. Repeat steps 2 and 3 through setting sequence. Setting sequence is: hour, minute, seconds.
100 laps). 5. Press B to exit setting mode.
3. Press D to display current set; press D again to scroll to next set.
4. Press and hold D 3 seconds to delete all stored data in the current set. Chronograph Mode
Note: At any point in recall displays, press A to exit and change to alarm mode.
1. In any mode, press and hold C 3 seconds to change to chronograph mode.
2. Press C to start the chronograph; press D to stop the chronograph.
Alarm Mode 3. Press and hold D 3 seconds to reset to zero.
1. Press A to change to alarm mode.
2. Press C to toggle alarm on/off.
Lap Counting
3. Press D to toggle alarm 1/alarm 2.
1. Press C while the chronograph is running for lap reading.
Note: If no other pusher is pressed after C is pressed, display will automatically show
Alarm Setting total chronograph time after 5 seconds, then next lap running time after another 5
1. In alarm mode, press and hold B 3 seconds; hour will begin flashing. seconds.
2. Press C to increase digit; press D to decrease digit. Press and hold C or D for fast 2. Press B to return to chronograph next lap (up to 100 laps).
increment/decrement. 3. Press D to stop chronograph.
3. Press A to set and advance to next setting value. 4. Press and hold B 3 seconds to save set data, or press and hold D 3 seconds to reset to
4. Repeat steps 2 and 3 through setting sequence. Setting sequence is: hour, minute, time zone zero.
1/time zone 2. Note: Upon saving, display will show next empty set available (1-9) or MEMORY
5. Press B to exit setting mode. FULL. Change to Recall Mode to scroll through saved data.
Note: Alarm will sound for 20 seconds. Press any pusher to silence alarm.

- 14 -
 Digital MD-FL298X, FL388, QFL226DB Digital FL145GR3

(B) (C) (A) (C)

(A) (D)
(B) (D)

Alarm on
Count stop
Hourly chime on
Count repeat
Automatic EL
Key tone Count up

Chronograph

A B C D
MODE
SET/EL MODE START/STOP LAP/RESET
SET (hold for
REAL TIME 2 seconds) TO CHRONOGRAPH TOGGLE TIME1/TIME2 KEY TONE ON/OFF

TIME SETTING EXIT NEXT ADVANCE DECREMENT

CHRONOGRAPH MEMORY RECALL TO TIMER START/STOP LAP/RESET

MEMORY RECALL NEXT LAP TO TIMER TO CHRONOGRAPH TO CHRONOGRAPH

SET (hold for

TIMER 2 seconds) TO ALARM START/STOP RESET

TIMER SETTING EXIT NEXT ADVANCE DECREMENT

SET (hold for

ALARM TIME 2 seconds) TO REAL TIME NEXT ALARM ALARM ON/OFF

ALARM SETTING EXIT NEXT ADVANCE DECREMENT

OVERVIEW
Features include DUAL TIME/DATE, CHRONO, TIMER, ALARM, and LIGHT UP EL.

LIGHT-UP EL
Press (A) to activate light-up function for 3 seconds.

TIME OF DAY MODE

- Press (C) to toggle between Time 1 and Time 2.
- Hold (C) for two seconds to set Time 1 or 2 as default.
- Press (D) to turn on/off key tone.
Time 1
- To set Time, press (A) until hour flashes. Press (B) to select the setting item. Use (C) and (D) buttons to adjust the values up or down. Press (A) to exit set mode.
Time 2
- To set Time, press (A) until hour flashes. Press (B) to select the setting item. Use (C) and (D) buttons to adjust the values up or down. Press (A) to exit set mode
- The range difference between Time 1 and Time 2 is 23 hours.

CHRONO MODE
- Press (C) to start and stop chronograph.
- Press (D) to Split/Reset the chronograph.
- Press (A) to recall the memory if Chronograph is stopped.
- Press (A) again to view the next lap.
- Press (C) or (D) to exit Recall mode and go back to Chronograph mode.
- There are a total of 10 lap memories.

TIMER MODE
- There are 3 different modes of timer: Count Down-Stop, Count Down-Repeat, Count Down-and Up.
- Press (C) to start/stop the timer counting.
- Press (D) to reset the counter to the preset value if timer is stopped.
- Press and hold (A) for 2 seconds to enter Timer Setting Mode.
Timer Setting Mode
- Press (B) to cycle around the setting item: timer-type, hour, minute, second and to back timer-type again.
- Press (C) and (D) to increase/decrease the setting value.
- Press (A) to exit the setting mode.
Timer Alarm
- Timer alarm will beep 2 times a second for 30 seconds.

ALARM MODE
- Press (C) to select the alarm.
- Press (D) to enable/disable the alarm.
- Press (B) to change to Time mode again.
Alarm Setting Mode
- Press and hold (A) for 2 seconds to enter the alarm settings mode.
- Press (C) and (D) to increase or decrease the settings value.
- Press (A) to exit the settings mode.

- 15 -
Digital FO-002
NORMAL TIME DISPLAY (B) (C)

1. Press B for EL.

2. Press C to display date.
3. Press D to display alarm.
4. Press C and D to toggle alarm on/off. will be displayed for alarm on.
(A) (D)
5. Press A and D to toggle chime on/off. All weekdays will be displayed for chime on.

TIME/DATE SETTING
1. From normal time display, press A 3 times to enter setting mode; seconds will begin flashing.
2. Press C to reset seconds to zero.
3. Press D to advance to minutes.
4. Press C to advance setting value.
5. Press D to set and advance to next setting.
6. Setting sequence is: seconds, minutes, hour, day, month, and weekday.
NOTE: When setting the hour, “H” is displayed for 24 hour format; “A” or “P” for 12 hour format.

ALARM SETTING
1. From normal time display, press A 2 times to enter setting mode; hour will begin flashing.
2. Press C to adjust setting value.
3. Press D to set and advance to minutes.
4. Press C to adjust setting value.
5. Press A to exit setting mode and return to Normal Time Display.
NOTE: Alarm will sound for one minute. Press D to stop alarm sound; press C for 5 minute snooze.

CHRONOGRAPH
1. From normal time display, press A 1 time to enter chronograph mode.
2. Press C to start/stop the chronograph.
3. Press D to reset to zero.
NOTE: While the chronograph is running, press A to return to Normal Time Display. Chronograph will continue
running in the background.

SPLIT TIME MEASUREMENT

1. Press D while the chronograph is running.
2. Press C to finalize timing and exit split count.
3. Press D to display all counts.
4. Press D to reset.

Digital ZD0603B01
NORMAL TIME DISPLAY
1. In normal time display, the display is off.
2. When the display is off, press A or B to enter time/date mode. A real time display scrolling animation will appear on the
(A) (B)
display first, and then the time display will be shown for 1 second. Followed by date display scrolling animation, the date
display will also be shown for 1 second, and then it will automatically shut off.

TIME/DATE SETTING
1. Press and hold A to enter setting mode; 12/24 hour format selection will begin flashing.
2. Press A to select 12/24 hour format.
3. Press B to set and advance to hour.
4. Press A to advance the setting value.
5. Press B to set and advance to next setting.
6. Setting sequence is: 12/24 hour, hour, minute, date, month, year.
7. Setting will automatically return to time display after year is set.
NOTE: The weekday will automatically be updated when the date, month, and year are set.

Digital MLL033
(A)
NORMAL TIME DISPLAY
1. Press A to display month and date for 3 seconds.
2. Press A twice to display seconds; press A again to return to normal time display.

TIME AND DATE SETTING (B)

1. Press B twice, to display month.
2. Press A to advance digit. Press and hold A for fast advance.
3. Press B to set and advance to next setting value.
4. Setting sequence is month, date, hour, minute.
5. Press B to set.
6. Press A to activate watch. Watch is activated when colon is flashing.
Note: To change from 12 to 24-hour format, when setting hour, scroll through all digits. 12-hour format is
indicated with “A” and “P”, and 24-hour format is indicated with “H”.

- 16 -
LED Digital MLG-035
NORMAL TIME DISPLAY (A)
1. Press A to display time for 8 seconds.
2. Press A again (while display is on) to change mode. Mode sequence is time, date.
Note: Animation will be displayed before time or date for 2 seconds.
Note: If no pusher is operated for 8 seconds, settings will be saved and the display will return to normal time
(B)
display.

TIME SETTING
1. Press A to display time.
2. Press and hold B, 12/24 hour format will begin flashing.
3. Press A to select 12/24 hour format.
Note: In 12-hour format, a small dot will be shown in the upper left hand corner of the display to indicate p.m.
time.
4. Press B to set and advance to hour.
5. Press A to advance digit; press and hold A for fast advance.
6. Press B to set and advance to next setting value.
7. Setting sequence is: 12/24 hour format, hour, minutes.
8. Press B to save and exit setting mode.

DATE SETTING
1. Press A to select date mode.
2. Press and hold B, date will begin flashing.
3. Press A to advance digit; press and hold A for fast advance.
4. Press B to set and advance to month.
5. Press A to advance digit; press and hold A for fast advance.
6. Press B to save and exit setting mode.

Curved LED Digital MLL-045

NORMAL TIME DISPLAY
1. Press B for time display and animation.
2. Press B again to toggle time/date mode.
(A)
3. When time or date is displayed, press and hold B for 3 seconds to toggle horizontal/vertical display.

TIME AND DATE SETTING

1. From time display, press and hold A; 12/24 hour format will begin flashing.
2. Press B to select 12/24 hour format.
NOTE: In 12 hour format, a small dot will be shown in the upper left hand corner of the display to indicate p.m.
time.
3. Press A to set and advance to hour.
4. Press B to advance digit. (B)
5. Press A to set and advance to next setting value.
6. Setting sequence is: 12/24 hour format, hour, minutes, date, month.
7. Press A to save and exit setting mode.
NOTE: If no pusher is operated for 7 seconds, settings will be saved and the display will return to normal time
display.

PERSONAL MESSAGE SETTING

1. Press B to display time, press B again to display date, press and hold A; first letter of message will begin flashing.
2. Press B to select character.
3. Press A to set and advance to the next character.
4. Repeat steps until desired message. Please note there are only ten spaces available.

OLED MODULE
(A)
The display is normally off. To activate display, press A for date display with scrolling time (Figure 1), or press B for time/date
display with animation (Figure 2).
NOTE: Animation is randomly selected from 4 designs. Press B to change animation. Figure 1

TIME/DATE SETTING (B)

1. When the display is activated, press and hold A for 2 seconds to enter setting mode. Hour will begin flashing.
2. Press B to advance digit. Press and hold B for fast advance.
3. Press A to set and advance to next setting value.
4. Setting sequence is hour, minute, month, date, year, 12/24 hour format. (A)

5. After the minute has been set, the seconds will reset to zero.
6. After 12/24 hour format has been selected, settings will be saved and the display will automatically return to time display. Figure 2
NOTE: If no pusher is operated for 7 seconds, settings will be saved and the display will return to time display.

(B)

- 17 -
Digital BJ2718, BJ2679, BJ2957
NORMAL TIME DISPLAY
1. Press A to change mode. Mode sequence is normal time, chronograph, alarm, and time setting.
2. Press B for EL.
(B) (C)
3. Press C to display date.
4. Press D to display alarm.
5. Press A+D to toggle chime on/off. (all days of week will display for “on”.)
6. Press C+D to toggle alarm on/off. (A) (D)

CHRONOGRAPH MODE
1. Press A to change to chronograph mode.
2. Press C to start/stop the chronograph.
3. Press D to reset to zero.
NOTE: Press A while the chronograph is running to return to normal time display; chronograph will continue running.

SPLIT TIME
1. Press D while the chronograph is running for split time.
2. Press D again to measure multiple split times.
3. Press C to finalize timing.
4. Press D to scroll through all counts.
5. Press D again to reset to zero. (B) (A) (C) (D)

ALARM SETTING
1. Press A to change to alarm setting mode; hour will begin flashing.
2. Press C to increase digit; press and hold C for fast advance. (A) (D)
3. Press D to confirm.
4. Press D again to toggle to minutes.
5. Press C to increase digit; press and hold C for fast advance.
6. Press A to save data and return to normal time display. (B) (C)
NOTE: Alarm will sound at preset time for 60 seconds. Press D to silence alarm, or press C for 5 minute snooze.

TIME AND CALENDAR SETTING

1. Press A to change to time and calendar setting; seconds will begin flashing.
2. Press C to set seconds to zero.
3. Press D to advance to minutes.
4. Press C to advance digit; press and hold C for fast advance.
5. Press D to advance to next setting value.
6. Setting sequence is: seconds, minutes, hour, date, month, weekday.
7. Press D to exit setting mode.
NOTE: When setting the hour, “H” will be displayed for 24-hour format; “A” or “P” for 12-hour format.

Digital BJ3101
NORMAL TIME DISPLAY (A) (B)
1. Press A for EL.
2. Press A to display date.

TIME AND DATE SETTING

1. Press B to enter setting mode; seconds will begin flashing.
2. Press A to set seconds to zero and return to normal time display.
3. Press B twice to set hour.
4. Press A to increase digit; press and hold A for fast advance.
5. Setting sequence is hour, minutes, month and date.
6. Press B to exit setting mode.

CURVED LED QFL631

NORMAL TIME DISPLAY
1. Press B for time display. (A)
2. Press B again immediately for date display.
3. After time or date display, message will scroll. Display will automatically turn off after message scrolling is complete. (B)

TIME AND DATE SETTING

1. Press and hold A for 2 seconds to enter setting mode; 12/24-hour format will begin flashing.
2. Press B to select 12/24 hour format.
3. Press A to advance to hour.
4. Press B to increase digits; press and hold B for fast advance.
5. Press A to advance to next setting value.
6. Setting sequence is: 12/24-hour format, hour, minutes, year, month, date
7. Press A to save and exit setting mode.
NOTE: If no pusher is operated for 7 seconds, settings will be saved and the display will automatically turn off.

MESSAGE SETTING
1. In calendar mode, press and hold A for 2 seconds to enter setting mode; first character will begin flashing.
2. Press B to change the character.
3. Press A to advance to next character.
NOTE: Maximum message length is 10 characters.

- 18 -