Scribd
Upload
16 views1 page

Ek Im 3831109870761

This document provides installation instructions for an EK-Supreme HF series water block on an Intel LGA-2011 socket motherboard. The instructions note that installation should only be done by an expert technician and improper installation could damage equipment. It then provides two sets of instructions for installing the water block depending on whether the customer received older or newer thumb screws. The instructions describe applying thermal paste or grease, placing springs and nuts over the screw stubs, and tightening the nuts in a cross pattern until fully seated.

Uploaded by

Ed Gar Yunda
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
16 views1 page

Ek Im 3831109870761

This document provides installation instructions for an EK-Supreme HF series water block on an Intel LGA-2011 socket motherboard. The instructions note that installation should only be done by an expert technician and improper installation could damage equipment. It then provides two sets of instructions for installing the water block depending on whether the customer received older or newer thumb screws. The instructions describe applying thermal paste or grease, placing springs and nuts over the screw stubs, and tightening the nuts in a cross pattern until fully seated.

Uploaded by

Ed Gar Yunda
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

EK-Supreme HF series water block installation for socket LGA-2011

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates. Before
installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the
liquid seal is made using o-rings. The use of an algaecide and corrosion inhibitors is always recommended for any liquid cooling system.

STEP 1: INTEL SOCKET LGA-2011 WATER BLOCK INSTALLATION PROCEDURE


STEP 1a: Installation of thumb screws FOR CUSTOMERS WHO RECEIVED 'OLD' SCREWS:
1) Place motherboard with preinstalled Intel LGA-2011 processor on an even
surface with front side facing up. STEP 1b: Fastening the waterblock:
2) Install four (4) thumb screws into four M4 threaded stubs on the LGA-2011 Install the waterblock on your CPU. Place an enclosed 2.5mm POM standoff
socket integrated latch mechanism (ILM). The screws are to be installed using no (an integral part of EK-Backplate Universal also enclosed with this water block),
tools (i.e. pliers). a compression spring and thumb nut over each threaded stub. Start fastening
3) Install Thermal Interface Material (TIM) or thermal grease as per installation two thumb nuts at a time, preferably in cross pattern and do not tighten them
manual. fully until all of them are partially screwed in. Then - using your fingers only -
screw in all four thumb nuts until you reach the end of the thread.

Thumb nut

Spring

2.5mm standoff
Thumb screw
EK-Supreme HF
LGA-2011 CPU
series water
socket
block

LGA-2011 CPU
socket

FOR CUSTOMERS WHO RECEIVED 'NEW' SCREWS:


Shipped from EK since Dec 16th 2011.

STEP 1b: Fastening the waterblock:


Install the waterblock on your CPU. Place an enclosed compression
spring and thumb nut over each threaded stub. Start fastening two
thumb nuts at a time, preferably in cross pattern and do not tighten
them fully until all of them are partially screwed in. Then - using
your fingers only - screw in all four thumb nuts until you reach the The NEW screws are clearly marked with
end of the thread. two milled grooves for easier recognition

Thumb nut

Spring

EK-Supreme HF
series water
block

LGA-2011 CPU
socket

th
All disclosures, notices and warranty conditions are being written on the back of the box. Released on 14 of December, 2011.

You might also like