08) 01) a), °. What is the maximum power that can be transmitted by the V belt having following data? Include centrifugal tension effect and state any assumptions made. Included angle of V groove= 30°, depth of the belt = 2 cm, width of the belt (top) = 2 cm, mass of the belt= 3.5 g/cm, maximum allowable stress= 140 N/cm:, coefficient of friction= 0.15, contact angle= 140° Two flat pulleys, one 450 mm diameter and other 200 mm diameter, on parallel shafts 1.95m apart are connected by a gressed belt. Determine the length of the belt required; the angles of contact between the belt and pulleys; the amount of power that can be transmitted by the belt when the larger pulley rotates at 200 rev/min, ifthe maximum permissible tension in the belt is 1kKN, and the coefficient of friction between the beltand the pulleys is 0.25; State any assumptions made. (4.98m; 2.73 kW)04) 07) ‘Anopen belt connects two flat pulleys. The pulley diameters are 300 mmand 450 mm and the corresponding angles of lap are 160° and 210°. The smaller pulley runs at 200 rpm. The coefficient of friction between the belt and pulleys is 0.25. It is found that the belt is on the point of slipping when 3 kW of power is being transmitted. To increase the power transmission capacity of the system two alternatives are suggested, namely (i) increasing the initial tension by 10%, and (it) increasing the coefficient of friction 10% by the application of a suitable dressing to the belt. Which of these two methods would be more effective? Find the percentage increase in power possible in each case. (3.30 KW; 3.27 kW; 10%; 996) Design a belt drive system (obtain basic dimensions) to transmit 110kW for a system consisting of 2 flat pulleys of diameters 0.9 m (driving pulley) & 1.2 m, center distance of 3.6 m, belt speed 20 m/s, coefficient of friction 0.3, slip 1.2% each pulley, 5% frictional loss at cach shaft and for 20% over loading. Take safe working stress of the belt as 2.5 MPa, and thickness of belt as 15 mm. Further states any assumptions (L=10.5 m; b= 3709 400mm) > List dawn and discuss briefly the factors that affect the power transmission capacity of a belt drive system.08) What is the maximum power that can be transmitted by the V belt having following data? Include centrifugal tension effect and state any assumptions made. Included angle of V groove= 30°, depth of the belt = 2 cm, width of the belt (top) = 2 cm, mass of the belt= 3.5 g/cm, maximum allowable stress= 140 N/cm?, coefficient of friction= 0.15, cantact angle= 140°5. a : @%) Show that when a belt dive is transmitting the maximum power, the maximum tension of the belt Tax = 3mv?. Where m; mass per unit length of the belt and v; belt speed. [30%] yo Power is transmitted between two shafts by a V-belt whose mass per unit length is 0.9 kg/m. The maximum permissible tension in the belt is limited to 2.5 KN. The angle of lap is 170°, and the groove angle is 45°, The coefficient of friction between the belt and pulleys is 0.18. Determine, i. velocity of the belt when the system transmits the maximum power, (10%) ii. power transmitted at this velocity, [25%] initial tension of the belt and [25%) iv. the fixing load applied on the pulley bearing. [10%] State all the assumptions clearly.4. A flat belt drive system is used to transmit power betwcen a prime mover and a machine. A pulley of 400 mm diameter and moment of inertia 5 kgm” with an angle of lap of the beit of 170° is connected to the machine shaft, At the starting from rest, the belt slips on the driven pulley for & seconds until the machine attains its steady speed of 400 rev/min. If the coefficient of friction between the belt and the pulley is 0.3 during the accelerating peri find. a. the tension ia both b. the load applied on the pulley bearings. [20%] c. the power transmitted by the belt at the steady speed, [10%] d the energy loss-due to the alip. (20%) the tight side and slack, side of the belt, [50%] ‘Suate all the assumptions clearly.3. A V-belt has to be designed to transmit 100 kW of power between two shafts whose centres are 1 m apart. The driving pulley has an effective ciameter of 300 mm and it runs at 1000 rev/min while the driven pulley rans at 400 rev/min. The angle of groove on the pulleys is 40°. The permissible stress ofa belt with cross-sectional area of 400 mum? is 2.1 MPa. The density of the belt material is 1100 kg/m, The coefficient of friction between the belt and the pulleys is 0.3. Estimate, ‘the number of belts required. [80%] b. Thenevessary installation force atthe pulley bearings. (20%) ‘You may refer to Figure Q3 for useful details. uo 4h Figure Q3. Usefal geometries of an open belt drive system.