Scribd
Upload
544 views9 pages

Denso rf7x Mazda Mitsubishi Nissan

This document provides connection instructions for reading from and writing to various DENSO ECU models used in Mazda, Mitsubishi, and Nissan vehicles, including the D3, 1J, RA6, RF8x, and RF7x. Different flat cable connections and adapters are required depending on whether reading or writing to the ECU, and whether using loose wires or a metal positioning frame connection. Proper power supply and attention to connections is emphasized.

Uploaded by

ahmedaitichou.021
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
544 views9 pages

Denso rf7x Mazda Mitsubishi Nissan

This document provides connection instructions for reading from and writing to various DENSO ECU models used in Mazda, Mitsubishi, and Nissan vehicles, including the D3, 1J, RA6, RF8x, and RF7x. Different flat cable connections and adapters are required depending on whether reading or writing to the ECU, and whether using loose wires or a metal positioning frame connection. Proper power supply and attention to connections is emphasized.

Uploaded by

ahmedaitichou.021
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

DENSO 1H_1J_D3_RA6_RF7x_RF8x

MAZDA_MITSUBISHI_NISSAN

1 DENSO 1H/1J/D3/RA6/RF7x/RF8x
MAZDA/MITSUBISHI/NISSAN

1.1 The below instructions apply to the following


ECUs:
ECU Brand ECU Model New Trasdata Plugin
DENSO D3/1J 0264
DENSO RA6 0265
DENSO RF8x 0277
DENSO RF7x 0278
DENSO 1H 0294

https://ecu.design
DENSO 1H_1J_D3_RA6_RF7x_RF8x
MAZDA_MITSUBISHI_NISSAN

https://ecu.design
DENSO 1H_1J_D3_RA6_RF7x_RF8x
MAZDA_MITSUBISHI_NISSAN

1.2 CONNECTIONS

ATTENTION

On this ECU, it is necessary to use two different FLAT cables, one for reading and one for writing.

1.2.1 LOOSE WIRES CONNECTION - ECU READING

ATTENTION

After making all the connections, connect a stabilized power supply to the New Trasdata and make sure
that the POWER LED (red) is on.

To communicate correctly with the control unit, it is necessary to use the F32GN037C/D and F34NTF53 cables.

WIRE COLOUR DESCRIPTION


Red +12 V
Black GND

https://ecu.design
DENSO 1H_1J_D3_RA6_RF7x_RF8x
MAZDA_MITSUBISHI_NISSAN
User manual

PIN WIRE COLOUR


17 PURPLE

18 GREY

19 WHITE

20 BLACK

21 BROWN

22 RED

23 ORANGE

24 YELLOW

25 GREEN

ATTENTION

Remove the plastic layer from the reading pads in order to properly solder the wires.
We recommended to use fine-grained sandpaper and to sand the surface by applying light pressure.

https://ecu.design
DENSO 1H_1J_D3_RA6_RF7x_RF8x
MAZDA_MITSUBISHI_NISSAN

1.2.2 LOOSE WIRES CONNECTION - ECU WRITING

ATTENTION

After making all the connections, connect a stabilized power supply to the New Trasdata and make sure
that the POWER LED (red) is on.

To communicate correctly with the control unit, it is necessary to use the F32GN037C/D and F34NTF51 cables.

WIRE COLOUR DESCRIPTION


Red +12 V
Black GND

https://ecu.design
DENSO 1H_1J_D3_RA6_RF7x_RF8x
MAZDA_MITSUBISHI_NISSAN

PIN WIRE COLOUR


1 BROWN

5 GREEN

6 BLUE

7 PURPLE

8 GREY

10 BLACK

ATTENTION

Remove the plastic layer from the reading pads in order to properly solder the wires.
We recommended to use fine-grained sandpaper and to sand the surface by applying light pressure.

https://ecu.design
DENSO 1H_1J_D3_RA6_RF7x_RF8x
MAZDA_MITSUBISHI_NISSAN

1.2.3 METAL POSITIONING FRAME CONNECTION - ECU READING

ATTENTION

After making all the connections, connect a stabilized power supply to the New Trasdata and make sure
that the POWER LED (red) is on.

The ECU must be powered using the cable F32GN037C/D.


Connect the GND and +12V pins to the black and red wires of the cable F32GN037C/D .

Adapter F34DM016 is required for the connection with the metal positioning frame.

Use the flat cable F34NTF03 to connect the adapter F34DM016 to the DIGITAL PORT of the New Trasdata.

https://ecu.design
DENSO 1H_1J_D3_RA6_RF7x_RF8x
MAZDA_MITSUBISHI_NISSAN

1.2.4 METAL POSITIONING FRAME CONNECTION - ECU WRITING

ATTENTION

After making all the connections, connect a stabilized power supply to the New Trasdata and make sure
that the POWER LED (red) is on.

The ECU must be powered using the cable F32GN037C/D.


Connect the GND and +12V pins to the black and red wires of the cable F32GN037C/D .

https://ecu.design
DENSO 1H_1J_D3_RA6_RF7x_RF8x
MAZDA_MITSUBISHI_NISSAN

Adapter F34DM019 is required for the connection with the metal positioning frame.

Use the flat cable F34NTF02 to connect the adapter F34DM019 to the DIGITAL PORT of the New Trasdata.

https://ecu.design

You might also like