TECHNICAL DATASHEET
Microswitches MS Series
General purpose microswitches for heavier duty applications
n High precision snap action mechanism n Protection degree IP20, IP40 or IP65
n 16A 250V AC resistive rating (Ith) n Versions with positive opening
n Wide range of actuator styles n Mechanically interchangeable with previous
n products (see cross reference section)
Screw terminals with self lifting plate
n 10 million mechanical operation cycles n UL and cUL Approvals
Options & Ordering Codes
MS ST C1 1 D A01 G
Terminal Type
Screw terminals with self-lifting plate ST Contacts Type
Silver contacts (standard)
Contact Block
1NO+NC, snap action C1 G Silver contacts gold plated 1 μm
Max. Protection Degree Actuator (see following pages)
IP40 (with protection) 1 A01 With pin
IP65 (with protection) 2 A02 With pin
A03 With small push button
Actuation Type
.. .................
Direct action D
Back direct action B ATTENTION! The feasability of a code number does not mean the effective availability of a product.
There are other options possible, if you can not see the option you require please contact IMO.
Inverted action R
www.imopc.com
TECHNICAL DATASHEET
Microswitches MS Series
Introduction
The MS series of microswitches has been developed with added features to replace the existing MV range. The
main features of the new range have been kept the same as the existing MV range to allow for interchangeability.
However, extra features have increased the application eld where these switches can be used. The innovative
feature of this series is the tripping device which has evolved with the use of modern technology, allowing added
features that oer a higher number of solutions when compared with similar devices currently present in the market.
The contacts of the new MS range have a higher reliability factor which has been achieved with the use of double
contacts which are also used where positive opening of the contact is required.
The housing has been designed so a gasket can be added as an option in order to seal the device against fine dust
or liquids up to IP65.
The terminals are more practical and allow for connection of a wider range of cable diameters. There are also
options available with Fast-On terminals, with the choice of three dierent terminal exit angles.
Contact Block Reliability
In the following table we refer to the typical microswitch contact structure (type A) normally used in the industry, compared with the innovative solution that IMO
Precision Controls uses in new MS series microswitches: movable contact with single interruption and double contacts (type B).
As you can see from the table below, this last structure (type B) offers half of the contact resistance (R) than the simple mobile contact (type A) and a lower probability
of failure ( fe).
In fact, defined x the probability of a commutation failure of a single interruption, it results that in the type A the failure probability fe=x, in the type B the probability fe=
x2. This means that if in a certain situation the failure probability x is equal, for instance, to 1 x 10-4 (1 failed interruption every 10.000), we will have:
- in type A one failed commutation every 10.000
- in type B one failed commutation every 100.000.000
Extended Temperature Range
On request the new MS series are also available with an extended temperature range. Where the IMO standard MS
microswitches have a temperature range of -25°C +85°C to , these special versions can be used in places where the
ambient temperature changes from -40°C to +85°C leading to possible installation inside cold stores, sterilizers or
other equipment using very low ambient temperatures. Special materials have been used to realize these versions
and these allow the specications and features to remain unchanged under these conditions, thereby widening the
installation possibilities. To have this option, add suffix H6 to the part number.
Microswitches For Safety Applications
All microswitches that have beside the part number have a positive opening mechanism therefore suitable
for safety applications.
These microswitches are provided with a rigid connection between the actuating plunger and the NC contacts,
which means these are opened by force through a strong/sturdy internal safety lever.
The positive opening is in conformity with the IEC 60947-5-1 standard and as such these microswitches are
suitable for installation in protection application.
www.imopc.com
TECHNICAL DATASHEET
Microswitches MS Series
Protection Degree IP20
By installing microswitches type MSSTC11xxx with terminal
cover AC-C01 it is possible to obtain a microswitch that is IP20.
Protection Degree IP40
By installing microswitch types MSSTC11xxx with terminal cover
AC-C02 it is possible to obtain a microswitch that is IP40.
Protection Degree IP65
By installing microswitch types MSSTC12xxx (not stocked) with
terminal covers AC-MSCV22 or AC-MSCV23 it is possible to obtain a
microswitch that is dustproof and waterproof and hence achieve IP65.
Clamping Screw Terminal For Different Size Cable
The clamping mechanism of the MS microswitches has been designed to allow for connection of dierent
diameter cables. The clamping plate is designed in such a way to force the cable towards the screw hence
achieving the most robust termination possible for all cable sizes within its specication.
Terminal Covers With Cable Gland Entry
Terminal covers can be supplied that incorporate
a trap cable gland to achieve a protection level
up to IP65.
These terminal covers are snap-in assembled
and when used increase the size of the
microswitch. The use of these covers
can also be extended to installations where
a number of microswitches are clamped
together.
Rotating Actuators
The microswitches have been designed to
allow the user to rotate the actuator head
(roller plunger types only) by 90° steps and this
is possible by removing the holding screws,
rotating the head and then retting the
screws back.
www.imopc.com
TECHNICAL DATASHEET
Microswitches MS Series
Technical Data
Housing:
Made of glass-reinforced polymer, self-extinguishing, shock-proof thermoplastic resin.
Protection degree: IP20 (with protection AC-C01 - AC-C03)
IP40 (with protection AC-MSCV • 1• - AC-C02)
IP65 (with protection AC-MSCV • 22 - AC-MSCV • 23)
according to EN 60529
General Data:
Ambient temperature: from -25°C to +85°C (-40oC option)
Max operating frequency: 3600 operations cycles 1/hour
Mechanical endurance: 10 million operations cycles 1
(1) One operation cycle means two movements, one to close and one to open contacts, as foreseen by EN 60947- 5-1 standard.
Main data Cross Section Of The Conductors (flexible copper wire):
MS Series: min. 1 x 0,34 mm 2 (1 x AWG 22)
• Polymer housing
max 2 x 1,5 mm 2 (2 x AWG 16)
• High reliability contacts
• Protection degree IP20, IP40 or IP65
• 4 terminal types available
In Conformity With Standards:
• 47 actuators available IEC 60947-5-1, EN 60947-5-1, IEC 60529, EN 60529.
• Versions with positive opening
Approvals:
• Silver contacts gold plated versions UL508
• Terminal covers with wire trap cable gland
In Conformity With Requirements Requested By:
• Mechanically interchangeable with previous Low Voltage Directive 2006/95/EC, Machinery Directive 2006/42/EC and Electromagnetic Compatibility
• products (see cross reference section) 2004/108/EC.
Positive Contact Opening In Conformity With Standards:
Markings & Quality Marks IEC 60947-5-1, EN 60947-5-1, EN 60947-5-1, VDE 0660-206.
Installation for safety applications:
Use only switches marked with the symbol . The safety circuit must always be connected with the NC contacts (normally closed contacts) as stated in the
standard EN 60947-5-1, encl. K, par. 2. The switch must be actuated by a travel length that is at least up to the positive opening travel (POT) value of which is listed
near the code article. The switch must be actuated at least with the positive opening force (POT), value of which is listed near the code article.
Electrical Data:
Thermal current (Ith): 16 A
Rated insulation voltage (Ui): 250 Vac 300 Vdc
Conditional shot circuit current: 1000 A according to EN 60947-5-1
Protection against short circuits: fuse 10 A 500 V type gG
Pollution degree: 3
Dielectric strength: 2000 Vac/min.
Utilisation Categories:
Alternate current: AC15 (50 ... 60 Hz)
Ue (V) 250 120
Ie (A) 6 6
Direct current: DC13
Ue (V) 24 125 250
Ie (A) 5 0,6 0,3
Data Type Approved By UL:
Utilisation categories: Q300 (69 VA, 125-250 Vdc)
A300 (720 VA, 120-300 Vac)
In conformity with standard: UL 508
www.imopc.com
TECHNICAL DATASHEET
Microswitches MS Series
Terminal Outline Dimension Fixing
Tighten the nut 1 with torque 2....3 Nm. Tighten the screws 4 with torque 0.6....0.8 Nm.
Tighten the screws 2 with torque 0.4....0.5 Nm.
Tighten the nut 3 M4 with torque 0.8....1.2 Nm.
NOTE: a torque higher than 1.2 Nm may cause the microswitch to break.
Wiring Dimension
With direct and back direct action [B, D] With inverted action [R]
MD Differential Travel OT Over-Travel RF Releasing Force
PT Pre-Travel POT Positive Opening Travel POF Positive Opening Force
OF Operating Force MD Movement Differential
Microswitches With Direct Action 10pcs per pack
MSSTC11DA01 PT 0.5mm OF 4 N MSSTC11DA02 PT 0.5mm OF 4 N
1NO+1NC OT 1.5mm RF 3 N 1NO+1NC OT 2mm RF 3 N
MD 0.5mm MD 0.05mm
MSSTC11DA03 PT 0.5mm OF 4 N MSSTC11DA04 PT 0.5mm OF 4 N
1NO+1NC OT 2mm RF 3 N 1NO+1NC OT 2mm RF 3 N
MD 0.5mm MD 0.05mm
www.imopc.com
TECHNICAL DATASHEET
Microswitches MS Series
www.imopc.com
TECHNICAL DATASHEET
Microswitches MS Series
www.imopc.com
TECHNICAL DATASHEET
Microswitches MS Series
Cross Reference
Terminal Protection Covers 10 pcs per pack
Terminal protection cover for screw terminals snap-in assembled and with wire Terminal protection cover for vertical faston terminals snap-in assembled and
trap cable gland. It allows the installation of more switches side by side. with wire trap cable gland. It allows the installation of more switches side by
side.
Protection Protection
Article Description Article Description
Degree Degree
Terminal protection cover without gasket for Terminal protection cover without gasket for
AC-MSCV12 multipolar cables from Ø 4 to Ø 7,5 mm
IP40 AC-MSCH12 multipolar cables from Ø 4 to Ø 7,5 mm
IP40
Terminal protection cover without gasket for
AC-MSCV22 multipolar cables from Ø 4 to Ø 7,5 mm
IP65
Terminal protection cover without gasket for
AC-MSCV23 multipolar cables from Ø 4 to Ø 7,5 mm
IP65
Protection Protection
Article Description Article Description
Degree Degree
Terminal protection cover for screw Terminal protection cover for screw
AC-C01 terminals
IP20
AC-C02 terminals with cable gland PG9 for IP40
multipolar cables from Ø 5 to Ø 7 mm
Ref:MS-0715v2 Errors and omissions excepted. Subject to change without notice. www.imopc.com
