Wind Alarm panel

User Manual
Model : AC-WAS100(R1)
 -Contents-

1. General
2. Specification
2.1 Technical specification 2.2 Electric specification
3. Configuration
4. Communication
5. Electrical Connections
6. System Configuration
7. Display Window
7.1 Booting 7.2 ANE View
7.3 Plot View 7.4 Data View
7.5 Setup 7.6 Information
8. Data View & Delete, Saving
8.1 Data view 8.2 Data delete
8.3 Data saving
9. Operation ‘Setup’
9.1 ANE Setup 9.2 System Environment
9.3 Date & Time Setup
10. Accessories
11. Caution
12. Troubleshoot
13. Dimensions
13.1 Dimensions 13.2 Cutting hole

-2-
1. General
Wind alarm panel is the equipment to meet Exxon-mobile 2017 rule requirement such as
MESQAC 2017 (Marine Environmental Safety and Quality Assurance Criteria for Tanker Vessels)
ExxonMobil E17/E1a: Vessels MUST be fitted with an anemometer Display /Monitoring Repeater
in the record (paper or digital) wind speed and direction, and designed to be capable of setting
a minimum speed limits with Audible/Visual Alarms in the CCR and on Deck if the set limits are
exceeded.
The equipment for suspension a unloading work with alarming against winding beyond setting
result when anchoring and unloading cargo oil or gas. It gets alarmed from wind alarm panel
in the cargo control room of the vessel inside and the incurred alarm warning is recognized
through the electric horn installed inside and on deck side.

2. Specification
2.1 Technical Specification

ITEM SPECIFICATION

Display LCD touch screen

0 – 70 m/s
Wind speed range
0 – 136 Knots

Relative : PORT 0 – 180, STBD 0 – 180

Wind direction range
True : 0 – 360 deg. (※Option)

About 5 years
Data storage period
(16Gbyte, 32,000,000 data)

Data storage Pushing data to USB

Paper output
Data output
(DATE,TIME,SPEED,DIRECTION)

Printing / Speed / Thermal Line / 90mm/sec

Resolution / Width(mm) 203 DPI / 57.50mm paper

Data recorder method USB port

Buzzer stop lamp(High, H-High alarm)

Visual alarm
/ On deck rotating lamp(※Option)

Buzzer(High, H-High alarm)

Audible alarm
/ On deck electric horn(※Option)

Wind speed setup Two points wind speed setup

Accessories Electric horn with Lamp(※Option)

-3-
2.2 Electric Specification

ELECTRIC SPECIFICATION

Power DC24V 500mA(no Horn, Lamp)

Operating Temp. 5 – 55 ℃

Storage Temp. 0 – 60 ℃

Humidity 0 – 95 %

Contact for alarm 2NC + 2NO

Communication NMEA0183

7 inch LCD(800*480) /
Display & Touch
RESISTIVE TOUCH SCREEN

ACC. Connection Horn with Lamp 2pin x 2

ACC. Supply range DC24V 13A (Max)

MACHANICAL SPECIFICATION

Main body SS400

Front cover AL

Color / Munsell No. Black / N0.0

Name Plate PC

Weight 3.7 kg (Max)

Main body size 205x280x120(VxHxT) mm

Front cover size 236x310(VxH) mm

-4-
3. Configuration

① LCD DISPLAY with TOUCH SCREEN

② Printer for recording alarm
③ USB port for saving recorded alarm
④ Operating power ON/OFF switch
⑤ High & High-high alarm buzzer stop with flickering lamp
⑥ High & High-high alarm buzzer

-5-
4. Communication

NMEA, NMEA 0183 is the standard for transmitting information such as time, location.
NMEA 0183 is determined on National Marine Electronics Association and use a serial bus
communication, ASCII code.

4.1 MWV – Wind Direction & Speed

-6-
4.2 ZDA – Local Date & Time

-7-
5. Electrical connections
5.1 AC-WAS100(R1) connection

-8-
6. System Configuration

-9-
7. Display Window
7.1 Booting Display

Referring to ‘Section 3 Configuration, when Power on ‘④ Power switch’,

it starts booting. First, ‘⑤ Buzzer stop with flickering lamp’ starts blinking
slowly and the blinking is getting faster and show the above display. Generally,
it takes about 20 sec.

-10-
7.2 ANE View

In the top menu, when you press the button, the above display is
shown.

User can see the wind speed and direction information from anemometer.

1) The unit / alarm limit / direction mode / vessel statue. Etc, are able to set on
‘Setup’ menu and re-boot, the setting is applied. The details can be found
on Section 9 Operating Setup.

a. SPEED : The speed unit : ‘m/s’ or ‘knots’

Alarm set point : ‘High alarm limit’ and ‘H/High alarm limit’
Shown form : Analog point and Digital value

b. Direction : ‘Relative type mode’ or 'True type mode’

Shown form : Analog point and Digital value

c. Vessel Status : ‘Voyage mode’ or ‘Anchorage mode’

d. Date/Time : ‘UTC’ or ‘DGPS’ time & date

-11-
2) Display example
a. Relative type & Anchorage mode, m/sec, UTC display

b. Relative type & Voyage mode, knots, UTC display

-12-
c. True type & Anchorage mode, m/sec, DGPS display(※Option)

d. True type & Voyage mode, knots, DGPS display(※Option)

-13-
7.3 Plot View

In the top menu, when you press the button, the above display is
shown.
It shows that the wind speed and direction information from Anemometer in
data over time shortly.
1) Yellow bar( ) means wind speed. User can see the data during on 5
mins as plot form, the each point is 1 sec.

2) Green bar( ) means wind direction, User can see the data on right
screen as vertical graph.

-14-
3) Display example
a. Relative type & m/sec, UTC display

b. Relative type & knots, DGPS display(※Option)

-15-
c. True type & m/sec, UTC display(※Option)

d. True type & knots, DGPS display(※Option)

-16-
7.4 Data View

When press button, the above display is shown.

It shows the history of High alarm and H-high alarm.

If select the certain date, user can see the alarm list occurred alarm on the date.
If there is no alarm on the date, the list is empty as the below picture.

-17-
7.5 Set-Up

When press button, user can see the above display.

All setting regarding anemometer can be arranged on this menu.
The details can be found on Section 9. Operating Setup.

-18-
7.6 Information

When press button, user can see the above display.

This menu shows information about manufacture company and details.
In addition, the model name and firmware version can be confirmed.

-19-
8. Data View & Delete, Saving
8.1 Data view
When press button, you can see the Data view display.

If user needs a history of high alarm and high high alarm on certain date, click
the button and select the date.

During on searching, the below message is shown.

After 1~2 sec, The list of alarm would be shown in sequence of time.

-20-
Press this button, it is able to check the previous page.

Press this button, it is able to check the next page.

-21-
8.2 Data delete
1). Delete the alarm list that had been occurred before 1 year.
a. Press the button, user can see the below display.

b. Press , It is able to delete the data had been occurred

before 1 year as present.
c. Press and go to the ‘Setup’ menu, press .
Then the below dialog is shown.

Input the password ‘2000’ and press the ,

Now, the system starts re-booting and the data before 1 year has been
deleted completely.

※ ATTENTION : BEFORE DELETE DATA, RECOMMEND TO BACKUP TO

YOUR DISK

-22-
8.3 Data View Refresh
1). Refresh the History List of Wind Speed Alarm
a. When press , user can see the below display.

b. Press the , the list is updated.

8.4 Data saving
1). Save the History List of Wind Speed
a. Press the button, user can see the below display.

b. Input USB stick to ③ USB port(‘Section 3 Configuration’).

And press the button.
Then, all alarm data is saved to USB as Excel file, and delete the list
on wind alarm system.

c. Go to the ‘Setup’ menu, press .

Then the below dialog is shown.

Input the password ‘2000’ and press the , Now, the system
starts re-booting.

-23-
9. Operation “Setup”

9.1 ANE Setup

1). Wind speed Unit
When press the of . , the unit of wind speed
changes to . When press it again, it changes to again.
If select the unit, press the , then the setting is applied to
system.
2). Set High Alarm
When press the. of
The dialog is shown as below.

Input the set value and press OK! Button, And then, press
, it is applied to system,

-24-
3). Set High-high Alarm
In the Setup, press the of
The dialog is shown as below.

Input the set value and press OK! Button, And then, press
it is applied to system,

4). Set ‘Anchorage mode’ & ‘Voyage mode’

When press the of , Vessel Status changes to
mode. When press it again, it changes to . If select the
mode, press the , then the setting is applied to system.

5). Printer Enable & Disable

In the Setup, when press the of , the printer
Write changes to . When press it again, it changes to .
If select the mode, press the , then the setting is applied to
system.

6). Printer Interval

In the Setup, when press the of ,
The dialog is shown as below.

Input the set value and press OK! Button, And then, press
, it is applied to system,

-25-
9.2 System Environment

1). Test Printer

If press the button, the below message will be printed.

If the print is not operated, the printer is abnormal.

2). Manager Mode! : This mode is for modifying DATE, TIME, special set for system.
The details can be found on Section 9.3.

3). Setup Save : It is for saving the change of set. If there is any change on set,
User should press this for applying it to system.

-27-
9.3 Date_Time Update
※ ATTENTION : This mode affects seriously to whole system, so, please
operate this mode only for special situation.

1) In the Setup, press the , the below dialog is shown.

Input the password 2000, and OK! button. Next, user can see the below display.

-28-
2) It is able to change the year, month, date, hour, minute, second when click
each part.

Click the each part of year, month etc, and set value as
3) And please save the set as press the button.

-29-
10. Accessories
Accessories of wind alarm panel are installed outside of the vessel, which has
electric horn that sailors can recognize an alarm for wind speed beyond
setting result. There is a manual for electric horn separately so please refer
to the manual. Two electric horns are installed in PORT and STBD on deck
side each to listen an alarm in both sides.

11. Caution
① Touch screen is easy to be damaged so, do not touch it as anything sharp
and do not give any shock.

② Please be carefully when connect cable on backside of AC-WAS100(R1)

to connect terminals the each cable correctly.
The details can be found on Section 5. Electrical connections.
* The system can be damaged when it is incorrect connection.

③ If there is an error of system, Please re-boot as press POWER button to

OFF of ④ ‘Section Configuration’.

-36-
12. Troubleshoot

Symptom Cause Action

There is nothing on screen Power Off Check power S/W off or

power cable.

After checking
communication cable,
reboot with power on-off.
The screen is freezing. Communication cable is not Reboot with power on-off
connection with. after checking
communication cable
connection.
Error program based on Reboot with power on-off.
window.
Printer is not operated. No paper in printer. Exchange a paper with
opening cover of printer.
Disable to print out. Reinstall the paper with
opening cover of printer.
Red LED is lighting. Recommend to repair the
printer or replace it.
Electric horn is not ring. Not connected with terminal Check cable condition.
block electric horn cable.
DC24V is not output when Recommend to repair the
back of alarm panel of wind alarm system.
electric horn’s connection
terminal block is alarmed by
multi tester.
If the horn is not ring when Recommend to check
the DC24V is output electric horn own.
normally from alarm panel.
It’s not work due to error on System error Reboot with power on-off.
screen.
in case it’s not work after
trying reboot, Install the
program again referring to 9.4
Program update
The front of buzzer or buzzer Buzzer or buzzer stop switch Recommend to repair.
stop switch is not work. trouble.

-37-
13. Dimensions
13.1 Dimension

-38-
13.2 Cutting hole

HERIANA Co., LTD.

#73, Hwajeonsandan 2-ro, Gangseo-gu,
Busan,Korea 45738
Tel: +82 (51)313-6690~1
Fax: +82 (51)313-6693
E-mail: [email protected], [email protected]

Website: http://www.heriana.com

This manual can be revised without any prior notice.

-39-