[ 5.037996] pci 0001:00:00.

0: PCI bridge to [bus 01]

[ 5.042945] pci 0001:00:00.0: bridge window [mem 0x40000000-0x400fffff]
[ 5.049781] pci 0001:00:00.0: 4.000 Gb/s available PCIe bandwidth (5.0 GT/s PCIe
x1 link)
[ 5.058094] pcie_iproc_bcma bcma0:9: host bridge /axi@18000000/pcie@14000
ranges:
[ 5.065581] pcie_iproc_bcma bcma0:9: No bus range found for
/axi@18000000/pcie@14000, using [bus 00-ff]
[ 5.075141] pcie_iproc_bcma bcma0:9: non-prefetchable memory resource required
[ 5.194270] pcie_iproc_bcma bcma0:9: PHY or data link is INACTIVE!
[ 5.200453] pcie_iproc_bcma bcma0:9: no PCIe EP device detected
[ 5.207406] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30
seconds, Software Timer)
[ 5.216429] bcma-host-soc 18000000.axi: bus0: Bus registered
[ 5.222597] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 5.228314] bcma-pci-bridge 0000:01:00.0: enabling device (0140 -> 0142)
[ 5.235052] bcma-pci-bridge 0000:01:00.0: bus1: Found chip with id 43217, rev
0x00 and package 0x08
[ 5.244097] bcma-pci-bridge 0000:01:00.0: bus1: Core 0 found: ChipCommon (manuf
0x4BF, id 0x800, rev 0x27, class 0x0)
[ 5.254707] bcma-pci-bridge 0000:01:00.0: bus1: Core 1 found: IEEE 802.11 (manuf
0x4BF, id 0x812, rev 0x1E, class 0x0)
[ 5.265410] bcma-pci-bridge 0000:01:00.0: bus1: Core 2 found: PCIe (manuf 0x4BF,
id 0x820, rev 0x14, class 0x0)
[ 5.276198] Can not parse mac address: 00:90:4C:0F:F
[ 5.300765] bcma-pci-bridge 0000:01:00.0: bus1: Bus registered
[ 5.306928] pci 0001:00:00.0: enabling device (0140 -> 0142)
[ 5.312581] bcma-pci-bridge 0001:01:00.0: enabling device (0140 -> 0142)
[ 5.319344] bcma-pci-bridge 0001:01:00.0: bus2: Found chip with id 0x4352, rev
0x03 and package 0x01
[ 5.328492] bcma-pci-bridge 0001:01:00.0: bus2: Core 0 found: ChipCommon (manuf
0x4BF, id 0x800, rev 0x2B, class 0x0)
[ 5.339097] bcma-pci-bridge 0001:01:00.0: bus2: Core 1 found: IEEE 802.11 (manuf
0x4BF, id 0x812, rev 0x2A, class 0x0)
[ 5.349784] bcma-pci-bridge 0001:01:00.0: bus2: Core 2 found: ARM CR4 (manuf
0x4BF, id 0x83E, rev 0x02, class 0x0)
[ 5.360126] bcma-pci-bridge 0001:01:00.0: bus2: Core 3 found: PCIe Gen2 (manuf
0x4BF, id 0x83C, rev 0x01, class 0x0)
[ 5.370638] bcma-pci-bridge 0001:01:00.0: bus2: Core 4 found: USB 2.0 Device
(manuf 0x4BF, id 0x81A, rev 0x11, class 0x0)
[ 5.413169] bcma-pci-bridge 0001:01:00.0: bus2: Invalid SPROM read from the PCIe
card, trying to use fallback SPROM
[ 5.424080] Can not parse mac address: 00:90:4C:0F:F
[ 5.433333] bcma-pci-bridge 0001:01:00.0: bus2: Bus registered
[ 5.440219] NET: Registered PF_INET6 protocol family
[ 5.449289] Segment Routing with IPv6
[ 5.452987] In-situ OAM (IOAM) with IPv6
[ 5.457124] NET: Registered PF_PACKET protocol family
[ 5.462236] bridge: filtering via arp/ip/ip6tables is no longer available by
default. Update your scripts to load br_netfilter if you need this.
[ 5.475697] 8021q: 802.1Q VLAN Support v1.8
[ 5.479967] Registering SWP/SWPB emulation handler
[ 5.489631] b53-srab-switch 18007000.ethernet-switch: found switch: BCM53011,
rev 5
[ 5.619266] b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB
callbacks. Please migrate to PHYLINK!
[ 5.629434] b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB
callbacks. Please migrate to PHYLINK!
[ 5.639523] b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB
callbacks. Please migrate to PHYLINK!
[ 5.651744] b53-srab-switch 18007000.ethernet-switch lan1 (uninitialized): PHY
[dsa-0.0:00] driver [Generic PHY] (irq=POLL)
[ 5.665787] b53-srab-switch 18007000.ethernet-switch lan2 (uninitialized): PHY
[dsa-0.0:01] driver [Generic PHY] (irq=POLL)
[ 5.679602] b53-srab-switch 18007000.ethernet-switch lan3 (uninitialized): PHY
[dsa-0.0:02] driver [Generic PHY] (irq=POLL)
[ 5.693427] b53-srab-switch 18007000.ethernet-switch lan4 (uninitialized): PHY
[dsa-0.0:03] driver [Generic PHY] (irq=POLL)
[ 5.707318] b53-srab-switch 18007000.ethernet-switch wan (uninitialized): PHY
[dsa-0.0:04] driver [Generic PHY] (irq=POLL)
[ 5.719456] DSA: tree 0 setup
[ 5.724100] UBI: auto-attach mtd4
[ 5.727563] ubi0: attaching mtd4
[ 6.526591] ubi0: scanning is finished
[ 6.542329] ubi0: attached mtd4 (name "ubi", size 122 MiB)
[ 6.547905] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 6.554788] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 6.561551] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 6.568492] ubi0: good PEBs: 976, bad PEBs: 0, corrupted PEBs: 0
[ 6.574476] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 6.581665] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image
sequence number: 1696887935
[ 6.590763] ubi0: available PEBs: 0, total reserved PEBs: 976, PEBs reserved for
bad PEB handling: 20
[ 6.600044] ubi0: background thread "ubi_bgt0d" started, PID 308
[ 6.607688] block ubiblock0_0: created from ubi0:0(rootfs)
[ 6.613179] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 6.626785] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 6.635231] Freeing unused kernel image (initmem) memory: 1024K
[ 6.654446] Run /sbin/init as init process
[ 7.029512] init: Console is alive
[ 7.033255] init: - watchdog -
[ 7.815077] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.927229] usbcore: registered new interface driver usbfs
[ 7.932792] usbcore: registered new interface driver hub
[ 7.938289] usbcore: registered new device driver usb
[ 7.951133] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.961937] fsl-ehci: Freescale EHCI Host controller driver
[ 7.970660] ehci-platform: EHCI generic platform driver
[ 7.982252] ehci-platform 18021000.usb: EHCI Host Controller
[ 7.988043] ehci-platform 18021000.usb: new USB bus registered, assigned bus
number 1
[ 7.996090] ehci-platform 18021000.usb: irq 45, io mem 0x18021000
[ 8.009215] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.019357] ohci-platform: OHCI generic platform driver
[ 8.025018] ohci-platform 18022000.usb: Generic Platform OHCI controller
[ 8.031759] ohci-platform 18022000.usb: new USB bus registered, assigned bus
number 2
[ 8.039724] ohci-platform 18022000.usb: irq 45, io mem 0x18022000
[ 8.045856] ehci-platform 18021000.usb: USB 2.0 started, EHCI 1.00
[ 8.054467] hub 1-0:1.0: USB hub found
[ 8.058445] hub 1-0:1.0: 2 ports detected
[ 8.119120] hub 2-0:1.0: USB hub found
[ 8.123515] hub 2-0:1.0: 2 ports detected
[ 8.154301] xhci-hcd 18023000.usb: xHCI Host Controller
[ 8.159586] xhci-hcd 18023000.usb: new USB bus registered, assigned bus number 3
[ 8.167309] xhci-hcd 18023000.usb: hcc params 0x02501164 hci version 0x100
quirks 0x0000800000010010
[ 8.176499] xhci-hcd 18023000.usb: irq 46, io mem 0x18023000
[ 8.182337] xhci-hcd 18023000.usb: xHCI Host Controller
[ 8.187590] xhci-hcd 18023000.usb: new USB bus registered, assigned bus number 4
[ 8.194994] xhci-hcd 18023000.usb: Host supports USB 3.0 SuperSpeed
[ 8.205292] hub 3-0:1.0: USB hub found
[ 8.209651] hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 8.218088] usb usb4: We don't know the algorithms for LPM for this host,
disabling LPM.
[ 8.227308] hub 4-0:1.0: USB hub found
[ 8.231683] hub 4-0:1.0: 1 port detected
[ 8.238807] kmodloader: done loading kernel modules from /etc/modules-boot.d/*