User Guide

© Copyright 2016 HP Development Company,

L.P.

HDMI, the HDMI Logo and High-Definition

Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
Windows is either a registered trademark or
trademark of Microsoft Corporation in the
United States and/or other countries.

The information contained herein is subject to

change without notice. The only warranties for
HP products and services are set forth in the
express warranty statements accompanying
such products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable for
technical or editorial errors or omissions
contained herein.

First Edition: March 2016

Document part number: 846778-001

About This Guide
This guide provides information on monitor features, setting up the monitor, using the software and technical
specifications.

WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or
loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to
equipment or loss of information.
NOTE: Text set off in this manner provides important supplemental information.
TIP: Text set off in this manner provides helpful hints.

This product incorporates HDMI technology.

iii
iv About This Guide
Table of contents

1 Getting Started ............................................................................................................................................. 1

Important safety information ............................................................................................................................... 1
Product features and components ........................................................................................................................ 2
Features ............................................................................................................................................... 2
Rear and side components .................................................................................................................. 3
Setting up the monitor .......................................................................................................................................... 4
Use caution when setting up the monitor ........................................................................................... 4
Attaching the monitor stand ............................................................................................................... 5
Connecting the cables ......................................................................................................................... 6
Connecting USB devices ...................................................................................................................... 8
Adjusting the monitor ......................................................................................................................... 8
Turning on the monitor ....................................................................................................................... 9
Mounting the monitor ....................................................................................................................... 10
Removing the monitor stand .......................................................................................... 10
Attaching the VESA mounting bracket ........................................................................... 11

2 Using the monitor ........................................................................................................................................ 12

Software and utilities .......................................................................................................................................... 12
The Information file ........................................................................................................................... 12
The Image Color Matching file ........................................................................................................... 12
Installing the .INF and .ICM files .......................................................................................................................... 12
Installing from the optical disc ......................................................................................................... 12
Downloading from the Internet ........................................................................................................ 13
Using My Display software .................................................................................................................................. 13
Installing the software ...................................................................................................................... 13
Using the software ............................................................................................................................ 13
Downloading the software ................................................................................................................ 13
Using the on-screen display (OSD) menu ............................................................................................................ 14
Using Auto-Sleep Mode ....................................................................................................................................... 15

3 Support and troubleshooting ........................................................................................................................ 16

Solving common problems .................................................................................................................................. 16
Button lockouts ................................................................................................................................................... 17
Product support ................................................................................................................................................... 17
Preparing to call technical support ..................................................................................................................... 17
Locating the rating label ...................................................................................................................................... 17

v
 4 Maintaining the monitor .............................................................................................................................. 19
Maintenance guidelines ....................................................................................................................................... 19
Cleaning the monitor ......................................................................................................................... 20
Shipping the monitor ......................................................................................................................... 20

Appendix A Technical specifications ................................................................................................................. 21

Preset display resolutions ................................................................................................................................... 22
Entering user modes ......................................................................................................................... 23
Power adapter ..................................................................................................................................................... 23
Energy saver feature ........................................................................................................................................... 23

Appendix B Accessibility ................................................................................................................................. 24

Supported assistive technologies ....................................................................................................................... 24
Contacting support .............................................................................................................................................. 24

vi
1 Getting Started

Important safety information

A power cord is included with the monitor. If another cord is used, use only a power source and connection
appropriate for this monitor. For information on the correct power cord set to use with the monitor, refer to
the Product Notices provided on your optical disc, if one is included, or in your documentation kit.

WARNING! To reduce the risk of electric shock or damage to the equipment:

• Plug the power cord into an AC outlet that is easily accessible at all times.
• Disconnect power from the computer by unplugging the power cord from the AC outlet.
• If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-pin
outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding
pin is an important safety feature.
For your safety, do not place anything on power cords or cables. Arrange them so that no one may
accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the electrical
outlet, grasp the cord by the plug.
To reduce the risk of serious injury, read the Safety and Comfort Guide. It describes proper workstation, setup,
posture, and health and work habits for computer users, and provides important electrical and mechanical
safety information. This guide is located on the Web at http://www.hp.com/ergo.
CAUTION: For the protection of the monitor, as well as the computer, connect all power cords for the
computer and its peripheral devices (such as a monitor, printer, scanner) to some form of surge protection
device such as a power strip or Uninterruptible Power Supply (UPS). Not all power strips provide surge
protection; the power strips must be specifically labeled as having this ability. Use a power strip whose
manufacturer offers a Damage Replacement Policy so you can replace the equipment, if surge protection
fails.

Use the appropriate and correctly sized furniture designed to properly support your HP LCD monitor.

WARNING! LCD monitors that are inappropriately situated on dressers, bookcases, shelves, desks, speakers,
chests, or carts may fall over and cause personal injury.
Care should be taken to route all cords and cables connected to the LCD monitor so that they cannot be pulled,
grabbed, or tripped over.
NOTE: This product is suitable for entertainment purposes. Consider placing the display in a controlled
luminous environment to avoid interference from surrounding light and bright surfaces that may cause
disturbing reflections from the screen.

Important safety information 1

 Product features and components
Features
This product is an AMD FreeSync-qualified display, which allows you to enjoy PC gaming with smooth,
responsive, tear-free performance whenever a picture changes on the screen. The external source connected
to your display must have the FreeSync driver installed.
AMD FreeSync technology is designed to eliminate stuttering and tearing in games and videos by locking a
display’s refresh rate to the frame rate of the graphics card. Check with the manufacturer of your component
or system for specific capabilities.

IMPORTANT: AMD Radeon Graphics and/or AMD A-Series APU-compliant displays with DisplayPort/HDMI
Adaptive-Sync required. AMD 15.11 Crimson driver (or newer) required to support FreeSync over HDMI.
NOTE: Adaptive refresh rates vary by display. More information is available at www.amd.com/freesync.

To enable FreeSync on the display, press the Menu button on the monitor to open the on-screen display
menu. Click Color Control > Quick View > Gaming.
The light-emitting diode (LED) backlit display has an active matrix, AMVA+ panel. The display features include
the following:
● 81.28 cm (32-inch) diagonal viewable area with 2560 x 1440 QHD resolution, plus full-screen support
for lower resolutions
● Tilt capability and easy viewing from sitting or standing position, or while moving from one side of the
monitor to the other
● AMVA+ technology providing wide viewing angles with colors that maintain their integrity
● HDMI (High-Definition Multimedia Interface) video input
● DisplayPort video input
● Plug and Play capability if supported by your operating system
● On-screen display (OSD) adjustments in 10 languages for easy setup and screen optimization
● My Display software for adjusting monitor settings through Windows
● HDCP (High-bandwidth Digital Content Protection) used on digital inputs
● Software and documentation disc that includes monitor drivers and product documentation
● VESA mounting bracket for attaching the display to a wall mount device or swing arm
● USB 2.0 hub with one upstream port and two downstream ports
● AMD FreeSync-qualified, providing PC gaming enjoyment with smooth, responsive, tear-free
performance whenever a picture changes on the screen

NOTE: For safety and regulatory information, refer to the Product Notices provided on your media disc, if
one is included, or in your documentation kit. To access the latest user guides or manuals for your product, go
to http://www.hp.com/support. Select Find your product, and then follow the on-screen instructions.

2 Chapter 1 Getting Started

Rear and side components

Component Function

1 Menu button Press to open the OSD menu, select a menu item from the OSD, or close the
OSD menu.

2 Plus button If the OSD menu is on, press to navigate forward through the OSD menu and
increase adjustment levels.

If the OSD menu is inactive, press to open the audio menu.

3 Minus button If the OSD menu is on, press to navigate backward through the OSD menu
and decrease adjustment levels.

If the OSD menu is inactive, press to advance to the next active input port
(HDMI, DisplayPort).

4 Power button When the monitor is off, press the button to turn on the monitor.

5 Power connector Connects an AC adapter.

6 USB 2.0 (upstream) Connects the USB hub cable from the source device to the monitor.

7 USB 2.0 (downstream) Connects optional USB devices to the monitor.

8 USB 2.0 charging Connects optional USB devices to the monitor.

(downstream)

9 HDMI ports (2) Connect the HDMI cables from source devices to the monitor.

10 DisplayPort Connects the DisplayPort cable from the source device to the monitor.

NOTE: The USB 2.0 downstream with charging port also provides current to charge a device such as a smartphone or
tablet. You can make the charging current available even when the monitor power button is switched off by changing
the settings in the OSD. Open the OSD and select Power Control > USB Power > On.

Product features and components 3

 Setting up the monitor
Use caution when setting up the monitor
To prevent damage to the monitor, do not touch the surface of the LCD panel. Pressure on the panel may
cause non-uniformity of color or disorientation of the liquid crystals. If this occurs the screen will not recover
to its normal condition.
If installing a stand, lay the monitor face down on a flat surface covered with a protective sheet foam or non-
abrasive cloth. This prevents the screen from getting scratched, defaced or broken as well as damage to the
front panel buttons.

NOTE: Your monitor may look different from the monitor in this illustration.

4 Chapter 1 Getting Started

Attaching the monitor stand
CAUTION: The screen is fragile. Avoid touching or applying pressure to the screen; doing so can cause
damage.
TIP: Consider the placement of the display, because the bezel might cause interfering reflections from
surrounding light and bright surfaces.

1. Lift the monitor from its box and place it face down on a flat surface covered by a clean, dry cloth.
2. Attach the stand to the monitor by inserting the bracket at the top of the stand into the slot on the back
of the display head until the bracket clicks securely in place.

Setting up the monitor 5

 Connecting the cables
NOTE: The monitor ships with select cables. Not all cables shown in this section are included with the
monitor.

1. Place the monitor in a convenient, well-ventilated location near the computer.

2. Connect a video cable.

NOTE: The monitor will automatically determine which inputs have valid video signals. The inputs can
be selected by pressing the Minus button on the side panel or through the on-screen display by pressing
the Menu button and selecting Input Control.

● Connect an HDMI cable to the HDMI connector on the back of the monitor and the other end to the
source device.

● Connect a DisplayPort cable to the DisplayPort connector on the rear of the monitor and the other
end to the DisplayPort connector on the source device.

6 Chapter 1 Getting Started

3. Connect a USB upstream cable to the USB upstream connector on the rear of the monitor and the other
end to a USB downstream connector on the source device.

4. Connect one end of the power cord to the power supply (1) and the other end to a grounded electrical
outlet (2), and then connect the round end of the power supply cord to the monitor (3).

WARNING! To reduce the risk of electric shock or damage to the equipment:

Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
For your safety, do not place anything on power cords or cables. Arrange them so that no one may
accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the
electrical outlet, grasp the cord by the plug.

Setting up the monitor 7

 Connecting USB devices
There is one USB upstream port and two USB downstream ports on the rear of the monitor.

NOTE: You must connect the USB upstream cable from the source computer to the monitor to enable the
USB ports on the monitor. Refer to Step 4 in Connecting the cables on page 6.

Adjusting the monitor

Tilt the monitor panel forward or backward to set it to a comfortable eye level.

8 Chapter 1 Getting Started

Turning on the monitor
1. Press the power button on the source device to turn it on.
2. Press the power button on the front of the monitor to turn it on.

CAUTION: Burn-in image damage may occur on monitors that display the same static image on screen for a
prolonged period of time.* To avoid burn-in image damage on the monitor screen, you should always activate
a screen saver application or turn off the monitor when it is not in use for a prolonged period of time. Image
retention is a condition that may occur on all LCD screens. Monitors with a “burned-in image” are not covered
under the HP warranty.
* A prolonged period of time is 12 consecutive hours of non-use.
NOTE: If pressing the power button has no effect, the Power Button Lockout feature may be enabled. To
disable this feature, press and hold the monitor power button for 10 seconds.
NOTE: You can disable the power LED in the OSD menu. Press the Menu button on the front of the monitor,
and then select Power Control > Power LED > Off.

When the monitor is powered on, a Monitor Status message is displayed for five seconds. The message shows
which input is the current active signal, the status of the auto-switch source setting (On or Off; factory default
is On), the current preset display resolution, and the recommended preset display resolution.
The monitor automatically scans the signal inputs for an active input and uses that input for the display.

Setting up the monitor 9

 Mounting the monitor
The monitor panel can be attached to a wall, swing arm, or other mounting fixture.

NOTE: This apparatus is intended to be supported by UL or CSA Listed wall mount bracket.
CAUTION: This monitor supports the VESA industry standard 100 mm mounting holes. To attach a third-
party mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm long screws are required. Longer
screws must not be used because they may damage the monitor. It is important to verify that the
manufacturer’s mounting solution is compliant with the VESA standard and is rated to support the weight of
the monitor display panel. For best performance, it is important to use the power and video cables provided
with the monitor.

Removing the monitor stand

You can remove the monitor panel from the stand to install the panel on a wall, a swing arm, or other
mounting fixture.

CAUTION: Before beginning to disassemble the monitor, be sure the monitor is turned off and all cables are
disconnected.

1. Disconnect and remove all cables from the monitor.

2. Lay the monitor face down on a flat surface covered by a clean, dry cloth.
3. Press down on the release latch (1) and slide the stand out of the slot on the display head (2).

10 Chapter 1 Getting Started

Attaching the VESA mounting bracket
A VESA mounting bracket is included with the monitor for use when attaching the monitor panel to a wall,
swing arm, or other mounting fixture.
1. Remove the monitor stand. Refer to Removing the monitor stand on page 10.
2. Remove the screw from the center of the rear of the display head.
3. Insert the tab at the bottom of the VESA bracket into the slot on the back of the display head until the
bracket clicks in place (1), and then secure the top of the bracket with the screw that was installed in the
center of the display head (2).

4. To attach the monitor to a swing arm or other mounting device, insert four mounting screws through the
holes on the mounting device and into the screw holes on the VESA bracket that was installed on the
rear of the monitor.

Setting up the monitor 11

 2 Using the monitor

Software and utilities

The optical disc that comes with the monitor contains files you can install on the computer:
● an .INF (Information) file
● ICM (Image Color Matching) files (one for each calibrated color space)
● My Display software

The Information file

The .INF file defines monitor resources used by Windows® operating systems to ensure monitor compatibility
with the computer’s graphics adapter.
This monitor is Windows Plug and Play compatible and the monitor will work correctly without installing
the .INF file. Monitor Plug and Play compatibility requires that the computer’s graphic card is VESA DDC2–
compliant and that the monitor connects directly to the graphics card. Plug and Play does not work through
separate BNC type connectors or through distribution buffers/boxes.

The Image Color Matching file

The .ICM files are data files that are used in conjunction with graphics programs to provide consistent color
matching from monitor screen to printer, or from scanner to monitor screen. This file is activated from within
graphics programs that support this feature.

NOTE: The ICM color profile is written in accordance with the International Color Consortium (ICC) Profile
Format specification.

Installing the .INF and .ICM files

After you determine that you need to update, you can install the .INF and .ICM files from the optical disc or
download them.

Installing from the optical disc

To install the .INF and .ICM files on the computer from the optical disc:
1. Insert the optical disc in the computer optical drive. The optical disc menu is displayed.
2. View the HP Monitor Software Information file.
3. Select Install Monitor Driver Software.
4. Follow the on-screen instructions.
5. Ensure that the proper resolution and refresh rates appear in the Windows Display control panel.

NOTE: You may need to install the digitally signed monitor .INF and .ICM files manually from the optical disc
in the event of an installation error. Refer to the HP Monitor Software Information file on the optical disc.

12 Chapter 2 Using the monitor

Downloading from the Internet
To download the latest version of .INF and .ICM files from the HP monitors support Web site:
1. Go to http://www.hp.com/support.
2. Select Find your product, and then follow the on-screen instructions.
3. Click Driver - Display/Monitor to open the list of drivers.
4. Click on the driver.
5. Click the System Requirements tab, and then verify that your system meets the program minimum
requirements.
6. Click Download and follow the on-screen instructions to download the software.

Using My Display software

The optical disc provided with the monitor includes My Display software. Use My Display software to choose
preferences for optimum viewing. You can select settings for gaming, movies, photo editing, or just working
on documents and spreadsheets. You can also easily adjust settings such as brightness, color, and contrast
using My Display software.

Installing the software

To install the software:
1. Insert the optical disc in your computer optical drive. The optical disc menu is displayed.
2. Select the language.

NOTE: This choice selects the language you will see while installing the software. The language of the
software itself will be determined by the operating system language.

3. Click Install My Display Software.

4. Follow the on-screen instructions.
5. Restart the computer.

Using the software

To open the My Display software:
1. Click the HP My Display icon on the taskbar.
Or
Click Windows Start on the taskbar.
2. Click All Programs.
3. Click HP My Display.
4. Select HP My Display.
For additional information, refer to the on-screen Help within the software.

Downloading the software

If you prefer to download the My Display software, follow the instructions below.

Using My Display software 13

 1. Go to http://www.hp.com/support and select the appropriate country and language.
2. Select Drivers & Downloads, type your monitor model in the Find by product search field, and click Go.
3. If necessary, select your monitor from the list.
4. Select your operating system, and then click Next.
5. Click Utility - Tools to open the list of utilities and tools.
6. Click HP My Display.
7. Click the System Requirements tab, and then verify that your system meets the program minimum
requirements.
8. Click Download and follow the on-screen instructions to download My Display.

Using the on-screen display (OSD) menu

Use the on-screen display (OSD) to adjust the screen image based on your viewing preferences. You can
access and make adjustments in the OSD using the buttons on the right side of the display or the buttons on
the remote control.
To access the OSD and make adjustments, do the following:
1. If the monitor is not already on, press the Power button to turn on the monitor.
2. To access the OSD menu, press the Menu button on the right side of the monitor or on the remote
control.
3. To navigate through the OSD menu, press the + (Plus) button on the monitor’s side panel or on the
remote control to scroll up, or the – (Minus) button to scroll down.
4. To select an item from the OSD menu, use the + or – buttons to scroll to and highlight your selection,
then press the Menu button to select that function.
5. Adjust the item using the + or – buttons to adjust the scale.
6. After adjusting the function, select Save and Return, or Cancel if you don’t want to save the setting,
then select Exit from the Main menu.

Main Menu Description

Brightness Adjusts the brightness level of the screen. The factory default range is 90.

Contrast Adjusts the contrast level of the screen. The factory default range is 80.

Input Control Selects the video input signal.

Color Control Selects and adjusts the screen color.

Image Control Adjusts the screen image.

Power Control Adjusts the power settings.

OSD Control Adjusts the on-screen display (OSD) controls.

Management Adjusts the audio settings and returns all OSD menu settings to the factory default settings.

Language Selects the language in which the OSD menu is displayed. The factory default is English.

Information Selects and displays important information about the monitor.

Exit Exits the OSD menu screen.

14 Chapter 2 Using the monitor

Using Auto-Sleep Mode
The display supports an OSD option called Auto-Sleep Mode that allows you to enable or disable a reduced
power state for the display. When Auto-Sleep Mode is enabled (enabled by default), the monitor will enter a
reduced power state when the host PC signals low power mode (absence of either horizontal or vertical sync
signal).
Upon entering this reduced power state sleep mode, the monitor screen is blanked, the backlight is turned off
and the power LED indicator turns amber. The monitor draws less than 0.5W of power when in this reduced
power mode. The monitor will wake from the sleep mode when the host PC sends an active signal to the
monitor (for example, if you activate the mouse or keyboard).
You can disable the Auto-Sleep Mode in the OSD. Press the Menu button on the side panel to open the OSD. In
the OSD select Power Control > Auto-Sleep Mode > Off.

Using Auto-Sleep Mode 15

 3 Support and troubleshooting

Solving common problems

The following table lists possible problems, the possible cause of each problem, and the recommended
solutions.

Problem Possible Cause Solution

Screen is blank or video is Power cord is disconnected. Connect the power cord.
flashing.

Power button is turned off. Press the front panel power button.

NOTE: If pressing the power button has no effect, press and

hold the power button for 10 seconds to disable the power
button lockout feature.

Video cable is improperly connected. Connect the video cable properly. Refer to Connecting the
cables on page 6 for more information.

System is in sleep mode. Press any key on the keyboard or move the mouse to
inactivate the screen blanking utility.

Video card compatibility. Open the OSD menu and select the Input Control menu. Set
Auto-Switch Input to Off and manually select the input.

Image appears blurred, Brightness is too low. Open the OSD menu and select Brightness to adjust the
indistinct, or too dark. brightness scale as needed.

No speaker volume or low Volume control is turned down. Adjust the volume control on the bottom left of the front
speaker volume. panel.

Volume is muted. Press up on the volume control to unmute the volume.

Volume is turned down in the OSD, Open the OSD and select Management > Audio and adjust the
volume scale.

Headphones are plugged in. Unplug the headphones. The speakers are disabled when the
headphones are plugged in.

Check Video Cable is Monitor video cable is disconnected. Connect the appropriate video signal cable between the
displayed on screen. computer and monitor. Be sure that the computer power is off
while connecting the video cable.

Input Signal Out of Range is Video resolution and/or refresh rate Change the settings to a supported setting (see Preset display
displayed on screen. are set higher than what the monitor resolutions on page 22).
supports.

The monitor is off but it did The monitor's power saving control is Open the OSD menu and select Power Control > Auto-Sleep
not seem to enter into a low- disabled. Mode and set auto-sleep to On.
power sleep mode.

OSD Lockout is displayed. The monitor's OSD Lockout function Press and hold the Menu button on the side panel for 10
is enabled. seconds to disable the OSD Lockout function.

Power Button Lockout is The monitor's Power Button Lockout Press and hold the power button for 10 seconds to unlock the
displayed. function is enabled. power button function.

16 Chapter 3 Support and troubleshooting

Button lockouts
Holding down the power button or Menu button for ten seconds will lock out the functionality of the buttons.
You can restore the functionality by holding the buttons down again for ten seconds. This functionality is only
available when the display is powered on, displaying an active signal, and the OSD is not active.

Product support
For additional information on using your monitor, go to http://www.hp.com/support. Select Find your
product, and then follow the on-screen instructions.

NOTE: The monitor user guide, reference material, and drivers are available at http://www.hp.com/support.

If the information provided in the guide does not address your questions, you can contact support. For U.S.
support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/
country/us/en/wwcontact_us.html.
Here you can:
● Chat online with an HP technician

NOTE: When support chat is not available in a particular language, it is available in English.

● Find support telephone numbers

● Locate an HP service center

Preparing to call technical support

If you cannot solve a problem using the troubleshooting tips in this section, you may need to call technical
support. Have the following information available when you call:
● Monitor model number
● Monitor serial number
● Purchase date on invoice
● Conditions under which the problem occurred
● Error messages received
● Hardware configuration
● Name and version of the hardware and software you are using

Locating the rating label

The rating label on the monitor provides the product number and serial number. You may need these
numbers when contacting HP about the monitor model. The rating label is located on the bottom of the
display head.

Button lockouts 17
18 Chapter 3 Support and troubleshooting
4 Maintaining the monitor

Maintenance guidelines
To enhance the performance and extend the life of the monitor:
● Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those controls
that are covered in the operating instructions. If the monitor is not operating properly or has been
dropped or damaged, contact an authorized HP dealer, reseller, or service provider.
● Use only a power source and connection appropriate for this monitor, as indicated on the label/back
plate of the monitor.
● Be sure the total ampere rating of the products connected to the outlet does not exceed the current
rating of the electrical outlet, and the total ampere rating of the products connected to the cord does
not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS or A)
for each device.
● Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug
firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
● Turn the monitor off when not in use. You can substantially increase the life expectancy of the monitor
by using a screen saver program and turning off the monitor when not in use.

NOTE: Monitors with a “burned-in image” are not covered under the HP warranty.

● Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or
covered. Never push objects of any kind into cabinet slots or other openings.
● Do not drop the monitor or place it on an unstable surface.
● Do not allow anything to rest on the power cord. Do not walk on the cord.
● Keep the monitor in a well-ventilated area, away from excessive light, heat or moisture.
● When removing the monitor stand, you must lay the monitor face down on a soft area to prevent it from
getting scratched, defaced, or broken.

Maintenance guidelines 19
 Cleaning the monitor
1. Turn off the monitor and unplug the power cord from the back of the unit.
2. Dust the monitor by wiping the screen and the cabinet with a soft, clean antistatic cloth.
3. For more difficult cleaning situations, use a 50/50 mix of water and Isopropyl alcohol.

CAUTION: Spray the cleaner onto a cloth and use the damp cloth to gently wipe the screen surface. Never
spray the cleaner directly on the screen surface. It may run behind the bezel and damage the electronics.
CAUTION: Do not use cleaners that contain any petroleum based materials such as benzene, thinner, or any
volatile substance to clean the monitor screen or cabinet. These chemicals may damage the monitor.

Shipping the monitor

Keep the original packing box in a storage area. You may need it later if you move or ship the monitor.

20 Chapter 4 Maintaining the monitor

A Technical specifications

NOTE: All specifications represent the typical specifications provided by HP's component manufacturers;
actual performance may vary either higher or lower.
For the latest specifications or additional specifications on this product, go to http://www.hp.com/go/
quickspecs/ and search for your specific display model to find the model-specific QuickSpecs.

Display 81.28 cm wide screen 32 inches wide screen

Type AMVA+

Viewable image size 81.28 cm diagonal 32 inch diagonal

Tilt -5° to 23°

Weight

Without stand 9.0 kg 19.8 lbs

With stand 10.7 kg 23.54 lbs

Dimensions (including stand)

Height 52.2 cm 20.551 in

Depth 17.894 cm 7.049 in

Width 86.164 cm 33.923 in

Maximum graphic resolution 2560 x 1440 (60 Hz)

Optimum graphic resolution 2560 x 1440 (60 Hz)

Text mode 720 x 400

Dot pitch 0.27675 mm

Pixels per inch 91.8 PPI

Horizontal frequency 24 kHz to 90 kHz

Vertical refresh rate 50 Hz to 60 Hz

Environmental requirements temperature

Operating temperature 5°C to 35°C 41°F to 95°F

Storage temperature -20°C to 60°C -4°F to 140°F

Relative humidity 20% to 70%

Power source 100 VAC to 240 VAC 50/60 Hz

Altitude:

Operating 0 m to 5,000 m 0 to 16,400 ft

Storage 0 m to 12 ,192 m 0 to 40,000 ft

Measured power consumption:

21
 Full power 72 W

Typical settings 54 W

Sleep <0.5 W

Off <0.3 W

Input terminal Two HDMI connectors, one DisplayPort

connector

Preset display resolutions

The display resolutions listed below are the most commonly used modes and are set as factory defaults. This
monitor automatically recognizes these preset modes and they will appear properly sized and centered on the
screen.

Preset Pixel format Horz freq (kHz) Vert freq (Hz)

1 640 × 480 31.469 59.94

2 720 x 400 31.469 70.087

3 800 × 600 37.879 60.317

4 1024 × 768 48.363 60.004

5 1280 × 720 45 60

6 1280 × 800 49.702 59.81

7 1280 × 1024 63.981 60.02

8 1440 × 900 55.935 59.887

9 1600 × 900 60 60

10 1680 × 1050 65.29 59.954

11 1920 × 1080 67.5 60

12 1920 × 1200 74.038 59.95

13 1600 × 1200 75 60

14 1920 × 1200 74.556 59.885

15 2560 × 1440 88.787 59.951

Preset Timing name Pixel format Horz freq (kHz) Vert freq (Hz)

1 480p 720 × 480 31.469 60

2 576p 720 × 576 31.25 50

3 720p50 1280 × 720 37.5 50

4 720p60 1280 × 720 45 60

5 1080p60 1920 x 1080 67.5 60

6 1080p50 1920 x 1080 56.25 50

22 Appendix A Technical specifications

Entering user modes
The video controller signal may occasionally call for a mode that is not preset if:
● You are not using a standard graphics adapter.
● You are not using a preset mode.
If this occurs, you may need to readjust the parameters of the monitor screen by using the on-screen display.
Your changes can be made to any or all of these modes and saved in memory. The monitor automatically
stores the new setting, and then recognizes the new mode just as it does a preset mode. In addition to the
factory preset modes, there are at least 10 user modes that can be entered and stored.

Power adapter
Manufacturer Model number Power supply rating

Chicony TPC-CA57 19.5 Vdc @ 4.62 A – 90 W

Energy saver feature

The monitor supports a reduced power state. The reduced power state will be entered into if the monitor
detects the absence of either the horizontal sync signal and/or the vertical sync signal. Upon detecting the
absence of these signals, the monitor screen is blanked, the backlight is turned off, and the power light turns
amber. When the monitor is in the reduced power state, the monitor will utilize <0.5 watts of power. There is
a brief warm-up period before the monitor will return to its normal operating state.
Refer to the computer manual for instructions on setting the energy saver mode (sometimes called power
management feature).

NOTE: The above power saver feature only works when connected to computers that have energy saver
modes.

By selecting the settings in the monitor's Sleep Timer utility, you can also program the monitor to enter into
the reduced power state at a predetermined time. When the monitor's Sleep Timer utility causes the monitor
to enter the reduced power state, the power light blinks amber.

Power adapter 23
 B Accessibility

HP designs, produces, and markets products and services that can be used by everyone, including people with
disabilities, either on a stand-alone basis or with appropriate assistive devices.

Supported assistive technologies

HP products support a wide variety of operating system assistive technologies and can be configured to work
with additional assistive technologies. Use the Search feature on your source device that is connected to the
monitor to locate more information about assistive features.

NOTE: For additional information about a particular assistive technology product, contact customer support
for that product.

Contacting support
We are constantly refining the accessibility of our products and services and welcome feedback from users. If
you have an issue with a product or would like to tell us about accessibility features that have helped you,
please contact us at (888) 259-5707, Monday through Friday, 6 a.m. to 9 p.m. Mountain Time. If you are deaf
or hard-of-hearing and use TRS/VRS/WebCapTel, contact us if you require technical support or have
accessibility questions by calling (877) 656-7058, Monday through Friday, 6 a.m. to 9 p.m. Mountain Time.

24 Appendix B Accessibility