NABM...
05 (S1) SERIES
VALVE AND VALVE ACTUATOR MODULATING CONTROL
NABM...05 (S1) SERIES
NABM series standard valve actuators are especially designed and
produced for applications in the HVAC systems. Our wide range of
standard valve actuators has been developed to operate and position
ball valves of different sizes.
High Neck
Ball Valve Actuator PRODUCT FEATURE
• Torque 5 Nm
• Valve size DN15(½“) / DN20(¾“) / DN25(1“) / DN32(1¼“)
• Power supply AC/DC 24V or AC 230V
• Control modulating DC 0(2)...10 V
• Shaft dimensions - 9.0 mm (fixed)
• Selectable direction of rotation of reversing actuator
• Available in high neck and low neck
Low Neck • Optional 1 adjustable SPDT auxiliary switch
Ball Valve Actuator • Adjustable angle of rotation
• Manual over-ride push button when required
MODEL SELECTION TABLE
MODEL / TYPE TORQUE POWER SUPPLY RUNNING TIME AUXILIARY SWITCH
NABM 1.2-05 HN 5 Nm AC/DC 24 V ± 10% 60...90 sec -
NABM 1.2-05S1 HN 5 Nm AC/DC 24 V ± 10% 60...90 sec 1 x SPDT (Adjustable)
NABM 2.2-05 HN 5 Nm AC 230 V ± 10% 60...90 sec -
NABM 2.2-05S1 HN 5 Nm AC 230 V ± 10% 60...90 sec 1 x SPDT (Adjustable)
*Available in low neck
DIMENSION (mm)
123.5
89 92.5 22.5 36.5
48.5
36.5
64.5
1000 18 For low neck
5
17.5
8.5 115 32.25
For long neck
53
01
TECHNICAL SPECIFICATION
MODEL NUMBER NABM 1.2-05 (S1) NABM 2.2-05 (S1)
TORQUE 5 Nm 5 Nm
DN15(½“) / DN20(¾“) / DN25(1“) DN15(½“)/ DN20(¾“) / DN25(1“)
DAMPER SIZE
/ DN32(1¼“) / DN32(1¼“)
SHAFT DIMENSION 9.0 mm (fixed)* 9.0 mm (fixed)*
POWER SUPPLY AC/DC 24 V ± 10% AC 230 V ± 10%
FREQUENCY 50...60 Hz 50...60 Hz
CONTROL SIGNAL (INPUT) DC 0(2)...10 V DC 0(2)...10 V
CONTROL SIGNAL (OUTPUT) DC 0...10 V DC 0...10 V
POWER CONSUMPTION
• OPERATING 3.0 W 3.0 W
• END POSITION 2.0 W 2.0 W
FOR WIRE SIZING 6.0 VA 6.0 VA
ELECTRICAL CONNECTION 1 m Cable 1 m Cable
AUXILIARY SWITCH RATING 2 (1.5) A, AC 250 V 2 (1.5) A, AC 250 V
PROTECTION CLASS Class III III Class II
ANGLE OF ROTATION 90° (95° mechanical) 90° (95° mechanical)
WEIGHT 0.55 Kg 0.55 Kg
LIFE CYCLE 60,000 Rotation 60,000 Rotation
SOUND LEVEL 40 dB 40 dB
IP PROTECTION IP54 IP54
OPERATING TEMPERATURE -20°...50° as per IEC 721-3-3 -20°...50° as per IEC 721-3-3
NON-OPERATING TEMPERATURE -30°...+60° C / IEC 721-3-2 -30°...+60° C / IEC 721-3-2
5%...95% rH non condensing / 5%...95% rH non condensing /
AMBIENT HUMIDITY
EN EN
MAINTENANCE Maintenance Free Maintenance Free
MODE OF OPERATION Type I / EN 60730-1 Type I / EN 60730-1
EMC CE & ISO 9000 EN / EEC CE & ISO 9000 EN / EEC
*Note that shaft dimension has a tolerance offset of ± 0.2mm.
02
NABM SERIES BALL VALVE ACTUATOR MODULATING CONTROL 5NM
NABM...05 (S1) SERIES
VALVE AND VALVE ACTUATOR MODULATING CONTROL
WIRING DIAGRAM NABM...05 (S1) DIRECTION OF ROTATION NABM...05 (S1)
POWER SUPPLY AC/DC 24V OR AC 230V Default factory setting: CW.
Direction of rotation can be change by toggling between CW/
AC/DC 24V AC 230V CCW switch on the actuator’s housing.
AC 230 V ±10%
WIRING DIAGRAM NABM...05 (S1) AUXILIARY SWITCH NABM...05 (S1)
AUXILIARY SWITCH Switch a factory-set at 5°.
The auxiliary switch can be optimally adjusted between 0°...90°.
M
a 2 2
1 1
3 3
Yellow Green Blue
S1 S2 S3
2 (1.5) A, AC 250 V
Actuator at 0° position
WIRING DIAGRAM NABM...05 (S1) REMARK
PARALLEL CONNECTION
During parallel operation, the output signal (terminal 6, DC 0...10
V) of the master actuator must be connected to terminal 5 of the
next slave actuator.
03
MIXING CLOSED MIXING OPEN ACTUATOR POSITION
A C A = Closed A C A = Closed Open
B = Open B = Open 90°
B C = Open B C = Open
Coil
Coil
0°
Closed
(Always CCW)
2-way Closed 2-way Open
95°
3-way Closed 3-way Open
IMPORTANT REMARK
For special requirement, consult your local Nenutec’s representative.
This actuator includes electrical and electronic components and may not be disposed as household garbage. Please consider the local valid legislation.
AC / DC 24 V: Connect via safety isolating transformer.
AC 230 V: To isolate from the main power supply, the system must incorporate a device which disconnects the phase conductor (with at least a 3mm contact gap.)
The performance specifications are nominal and conform to acceptable industry standards. NENUTEC shall not be liable for damages resulting from misapplication or misuse of its
products.
04
NABM SERIES BALL VALVE ACTUATOR MODULATING CONTROL 5NM
