Bell-Housing

LMG series
IEC electric motor range from size 63 up to size 225

51 Bell-Housing
BELL-HOUSING & COUPLING SIZING
A GUIDE TO SELECT THE CORRECT BELL-HOUSING AND DRIVE COUPLING

DATA REQUIRED
- Electric motor power/motor size
- Manufacturer and pump type

TO VERIFY:
1 - Pump and motor shaft dimensions (see electric motor data sheet)
2 - Shaft and flange pump (see pump data sheet)

Example:
- Electric motor 2.2 kW - size 100-112
- Atos pump code PFE31 - Shaft 1

IEC Electric motor dimension Hydraulic pump dimension

ø250 ø19.05 - key 4.76

code G01 see page 18

Nr.2ø11

9.5
ø82.55
ø28 - key 8 60 57.5 ø106.4
code M05 see page 18

Case A
Solution with monobloc bell-housing series LMC/LDC
Pages 63 ÷ 69 for IEC Electric motor size 100-112 - LMC250
Bell-Housing’s length calculation
LMC 250 bell-housing with height ≥ 135.5 - LMC250AFSQ

- H = 60 + 18 + 57.5 = 135.5 mm (18 = Sp spider - see page 31) The bell-housing code must be completed with pump drilling code (see pages 48-49).
For the specific case:
- Choose type of bell-housing (LMC - LMS): Spigot hole 82.55 - PCD 106.4 - Nr.2 holes M10 : Drilling code 060
For monobloc bell-housing LMC/LDC series see pages 63 ÷ 69
For Low noise bell-housing LMS/LDS series see pages 71 ÷ 77 Definitive bell-housing code LMC250AFSQ060
For Multi-components 2-3 bell housing series see pages 79 ÷ 99
Case B
Note: Solution with low noise bell-housing series LMS/LDS
The length of bell-housing must be ≥ than the length calculated (135.5 mm)
Pages 71 ÷ 77 for IEC Electric motor size 100-112 - LMS250

LMS 250 bell-housing with height ≥ 135.5 - LMS250AFSA

The bell-housing code must be completed with pump drilling code (see pages 48-49).
For the specific case:
Spigot hole 82.55 - PCD 106.4 - Nr.2 holes M10 : Drilling code 060

Definitive bell-housing code LMS250AFSA060

Introduction 10
 BELL-HOUSING & COUPLING SIZING
A GUIDE TO SELECT THE CORRECT BELL-HOUSING AND DRIVE COUPLING

Coupling selection
Motor half-coupling (see page 26)
For IEC Electric motor size 100/112, the half-coupling is SGEA21M05060FG

Spider (see page 31)

For SGEA21, EGE2 - EGE2RR
(choose spider material on the base of the application, oil, temperature and cycle machine, etc.)

Pump half-coupling
Choose the drilling code - see pages 18-19 for shaft 19.05 - key 4.76 - code: G01

Pump half-coupling length = BH length - THK Spider - THK Spigot

LMC = 138 mm - 60 - 18 - 9.5 = 50.5 mm
LMS = 148 mm - 60 - 18 - 9.5 = 60.5 mm

LMC - Choose the half-coupling’s length at page 26 ≤ 50.5 mm.

LMS - Choose the half-coupling’s length at page 26 ≤ 60.5 mm.
LMC - Available length for SGEA21 = 50 mm
LMS - Available length for SGEA21 = 60 mm
Half coupling for LMC: SGEA21G01050FG
Half coupling for LMS: SGEA21G01050FG

SOFTWARE FOR AUTOMATIC CALCULATION

available on the web site www.mpfiltri.com

Note: for multi pumps we recommend to use a specific support on the base of the pump’s dimensions and weight.

11 Introduction
BELL-HOUSING & COUPLING SIZING Selection Software

Step 1 Select “BELL-HOUSING & COUPLING”

Step 2 Choose Manufacturer:

select “Pump type” and “Pump model”

Step 3 Choose nr° of poles of “Electric motors”:

select “Electric motors type” and “Electric motors size”

Step 4 Choose Coupling material

Introduction 12
Selection Software BELL-HOUSING & COUPLING SIZING

Step 5 Push “CLICK HERE TO PROCEED”, then choose best solution for your application.

Step 6 Push “PREVIEW” to download the reports.

Step 7
Download PDF
Datasheet and “DXF Drawing” of your selection

194
A
Questo documento e' di proprieta' della MP filtri S.p.A. - Senza autorizzazione scritta della stessa non potra' essere utilizzato per la costruzione dell'oggetto rappresentato ne venire conunicato a terzi . La societa' proprietaria tutela i propri diritti a rigore di legge .
All proprietary rights reserved by MP filtri S.p.A. - This drawing shall not be reproduced, or in any way utilized, for the manufacture of the component or unit herein illustrated and must not be released to other parties, without written consent . Any infringement will be legally pursued .

31
Nr. 4 holes M16

Nr.2 holes M12

109 26 45
Ø25 - Ch.8

54,5
Ø 4 2 - C h. 12

8 M
Ø350

Ø250

Ø100

Sec. A-A

Ø140 A

Ø 300
Prodotto/Product Disegnato/Drawn. Data/Date Per errori ammissibili di quote

AKMM05Z0007
senza tolleranze e per altre
20/02/2017 prescrizioni generali vedi
Complete kit for: Materiale/Material
Controllato/Checked Data/Date UNI EN 22768-1/1996 - f

-IEC Electric Motor Size 160 Peso/Weight Q.tà/Qty

For the permissible errors on the
dimensions without tollerance and

-Pump Bosch Rexroth A10VSO45 shaft P C.a. 7Kg

for other general specifications .
See UNI EN 22768-1/1996 - f

Scala/Scale
B.O.M. 1:2
ITEM QTY CODE DESCRIPTION Trattamento/Treatment

A 1 LMC350AFSU072 Monobloc Bellhousing

Revisioni/Modification

Denominazione/Description N° Disegno/Drawing No. REV.

1
FORMAT
B 1 EGE5 Spider Tav./Sht.

C 1 SGEA51D02045FG Motor Half Coupling

Complete Kit A3 di/of 1
Norma di collaudo/Tested std. Dis.grezzo/Raw Componente/Component Sostituisce/Supersedes
D 1 SGEA51M07109FG Pump Half Coupling

You can’t find the pump on the system?

Insert pump’s dimension on the section

“INSERT PUMP” and follow the instructions
to achieve the couplings components code

13 Introduction
GENERAL INFORMATION NOISE

Noise is a particularly pervasive problem so much so that there have been statutory regulations in place now for some years, designed to limit harmful
occupational exposure.
Many of the machines used in industry today are equipped with oil-hydraulic systems, which happen to be a major source of noise.

1 THEORY AND DEFINITION OF NOISE 2 SOUND

From a health and hygiene standpoint, noise can be defined as an unpleasant Technically considered, certain elements must be present simultaneously
and undesirable sound, or an unpleasant and annoying or intolerable auditory for acoustic phenomena to occur:
sensation (noise being any sound phenomena that may be accompanied by
sensations of disturbance and pain). By definition, acoustic phenomena are - Sound source
oscillatory in character, propagated in a flexible medium and causing pressure - Transmission medium
variations at the points, and the areas adjacent to those points, through which - Receive
they pass.
The electric motor and the pump, together with the drive coupling, are the
SOURCE OF THE NOISE. The Bell-housing is the noise transmission MEDIUM.
Depending on whether the monobloc bell-housing is a rigid or low noise type,
there will be variations in the flexible properties of the transmission medium.
The acoustic phenomena are dissimilar in the two cases, given the differences in
pressure variation and particle displacement.

MOTOR AND PUMP UNIT

BELL-HOUSING

ELECTRIC MOTOR
PUMP

RECEIVER
- Human ear
- Sound level meter

Bell-Housing 46
 ASSEMBLY OF MOTOR AND PUMP UNIT

Low noise bell-housing will help to attenuate the transmission of vibrations and the emission of noise generated by the system.
Self-evidently, however, the mere adoption of a low noise bell-housing will achieve little unless the motor and pump are correctly installed on the machine
or on the tank of the hydraulic power unit.

Should be followed in order to achieve best possible results and correct installation:

1 MOTOR AND PUMP UNIT MOUNTED 2 MOTOR AND PUMP UNIT MOUNTED
HORIZONTALLY ON OIL TANK LID HORIZONTALLY ON MACHINE
- The suction pipe attached to the pump must be rigid and fitted using a resilient - As a matter of good practice, the oil tank and motor-pump unit should be
bulkhead flange of the FTA series, which helps to cushion the vibrations mounted on a single supporting frame of strength sufficient to support the load.
propagated between the pipe and the tank lid.
If pipes need to be bent, the radius of curvature must be at least 3 times the - If the hydraulic system is fitted with a side-mounted filter, the suction pipeline
pipe diameter. to the pump must be flexible and long enough to include bends with the
Do not use elbow fittings, as these will significantly increase pressure losses. minimum radius of curvature recommended by the manufacturer.

- The pressure pipeline of the pump must be flexible and long enough to - If the suction filter is not side mounted, the pipeline should be rigid and
include bends with the minimum radius of curvature recommended by the installed in conjunction with a compensating coupling.
manufacturer for the specified operating pressure.
- The pressure pipeline of the pump must be flexible, and long enough to include
- The return pipeline running from the service to the filter must be flexible. bends with the minimum radius of curvature recommended by the manufacturer
Where oil is returned directly to the tank of the hydraulic power unit through for the specified operating pressure.
a rigid pipe, it is advisable to use a resilient bulkhead flange of the FTR series,
which helps to cushion the vibrations propagated between the pipe and - The return pipeline running from the service to the filter must be flexible.
the tank lid. Where oil is returned directly to the tank of the hydraulic power unit through
a rigid pipe, it is advisable to use a resilient bulkhead flange of the FTR series,
- Anti-vibration devices (resilient mounts or damping rods) must be located which helps to cushion the vibrations propagated between the pipe
under the feet of the electric motor or the PDM foot brackets, depending on and the tank lid.
the mounting position of the motor.
- Anti-vibration devices (resilient mounts or damping rods) must be located
- The lids of hydraulic oil tanks must be sturdy enough to support the load under the feet of the electric motor or the PDM foot brackets, depending
they carry. on the mounting position of the motor.

FINAL CONSIDERATION
For best results, in any event, the motor-and-pump unit should be incorporated into the hydraulic system in such a way that no one component is rigidly associated
with another, resulting in the propagation of vibration, and consequently noise.

RECOMMENDED TIGHTENING TORQUES FOR MOTOR/PUMP FIXING ON THE BELL-HOUSING

M6 10 N∙m M16 205 N∙m
M8 15 N∙m M18 280 N∙m
M10 50 N∙m M20 400 N∙m
M12 84 N∙m M22 530 N∙m
M14 135 N∙m M24 690 N∙m

Note: The above guidelines are indicative only and subordinate to the solutions adopted ultimately by design engineers.

47 Bell-Housing
GENERAL INFORMATION PUMP INTERFACE CODES

Spigot hole D Nr. holes Code Type

[mm] PCD
Valid configuration
for bell-housing up to ø400 40 72.00 M8 2 191 -
88.90 M8 4 096 -
45.2 120
71.80 M8 4 -
80.00 M8 2 052 ISO3019-2-50-B2
93.00 M10 2 053 -
Bell-housing with nr. 2 holes
50 60.00 M5 4 280 -
at pump interface, aligned
PCD

with through holes at motor 63.00 ø7 4 057 -

interface. 93.00 M8 2 287 -
50.8 82.50 M8 2 050 SAE A-A 50-2
Spigot

56 76.00 M6 4 234 -
hole

57.15 106.40 ø11 2 212 -

74.00 M10 4 098 -
60 98.50 M6 4 147 -
75.00 M6 4 227 -
62.7 157.20 M12 4 231 -
100.00 M8 2 042 ISO3019-2-63-B2
125.00 M6 4 043 -
Bell-housing with nr. 4 holes at 85.00 M8 4 044 -
PCD

pump interface, aligned with 80.00 M8 2 051 -

63
thread holes at motor interface. 80.00 ø8,5 4 058 -
100.00 M10 2 062 -
168
Spigot

85.00 M8 4 ISO3019-2-63-B4
hole

90.00 M8 4 271 -
65 90.00 M8 4 073 -
70 84.00 ø7 4 289 -
Valid configuration for bell-housing 71.8 88.90 M10 4 047 -
from ø450 to ø660 75 102.00 M10 4 139 -
100.00 M8 4 024 ISO3019-2-80-B4
103.20 M8 2 045 ISO3019-2-80-B2
100.00 ø11 4 059 -
100.00 M10 2 061 -
110.00 M10 2 063 -
140.00 M10 2 064 -
115.00 M10 2 065 -
Bell-housing with nr. 2 holes
100.00 M10 4 067 -
at pump interface + 22.5°
PCD

80
compared to through holes at 106.40 M10 2 083 -
motor interface. 130.00 M8 4 087 -
100.00 ø8,5 4 093 -
Spigot
hole

113.00 M12 4 104 -

95.00 M8 4 169 -
103.00 M8 4 242 -
110.00 M10 4 272 -
106.40 M10 2 060 SAE A 82-2
105.00 M10 4 097 -
82.55 106.40 M8 2 254 -
146.00 M12 2 260 -
110.00 M10 2 284 -
Bell-housing with nr. 4 holes 85 106.40 M10 2 066 -
at pump interface + 22.5° 112.00 M8 2 134 -
PCD

compared to thread holes at 105.00 M8 4 156 -

motor interface. 90
118.00 ø9 2 163 -
112.00 ø9 2 164 -
Spigot
hole

140.00 M8 4 088 -
92
145.00 M10 4 089 -
“-”: configuration out of ISO & SAE Standard

Bell-Housing 48
PUMP INTERFACE CODES GENERAL INFORMATION

Spigot hole D Nr. holes Code Type Spigot hole D Nr. holes Code Type
[mm] PCD [mm] PCD
115.00 M8 4 137 - 130 165.00 M10 4 253 -
95
127.00 M10 4 131 - 160.00 M10 4 151 -
135
98.4 125.00 ø11 4 128 - 175.40 M12 4 220 -
125.00 M10 2 023 ISO3019-2-100-B4 180.00 M14 4 077 ISO3019-2-140-B4
125.00 M10 4 025 ISO3019-2-100-B2 180.00 M12 2 081 -
125.00 ø11 4 031 - 165.00 M10 4 157 -
140
125.00 M5 4 032 - 200.00 M16 4 176 ISO3019-2-140-B2
190.00 ø15 4 038 - 165.00 ø11 4 223 -
125.00 ø13 4 041 - 180.00 M16 2 232 -
100 125.00 M12 2 071 - 150 185.00 M16 4 069 -
140.00 M12 2 072 - 228.60 M16 4 022 -
146.00 M12 2 075 - 228.60 M18 2 090 -
126.00 M10 2 106 - 228.60 M18 4 108 -
120.00 M8 4 122 - 152.4 217.50 ø17 4 118 -
160.00 M10 4 141 - 228.60 M20 2 166 SAE D 152-2
150.00 M10 4 150 - 228.60 M20 4 192 SAE D 152 -4
161.50 M12 4 029 - 190.50 M8 4 207 -
146.00 M12 2 070 SAE B 101-2 200.00 M16 4 027 ISO3019 - 2 -160 B4
101.6 127.00 M12 4 125 - 200.00 ø17 4 035 -
146.00 M10 2 159 - 200.00 M16 2 091 -
127.00 M10 4 224 - 224.00 M20 2 092 ISO3019 - 2 -160 B2
105 146.00 M12 2 076 - 160 200.00 M12 2 107 -
175.00 M10 4 110 - 230.00 M22 4 111 -
130.00 M8 4 154 - 185.00 M12 4 152 -
110 200.00 M10 4 202 - 224.00 M16 4 184 -
135.00 M10 4 219 - 230.00 ø22 4 228 -
145.00 M12 4 273 - 162 188.00 M12 4 263 -
140.00 M12 2 074 - 317.35 M20 4 143 SAE E 165 - 4
112 140.00 M10 2 138 - 317.35 M24 2 145 SAE E 165 - 2
165.1
130.00 M10 4 264 - 229.00 M20 4 201 -
115 180.00 M12 4 198 - 317.35 M18 4 204 -
116 160.00 M14 2 084 - 200.00 M12 4 153 -
175
210.00 M16 2 094 - 230.00 M18 2 185 -
120 145.00 M10 4 155 - 350.00 M24 4 146 SAE F 177 - 4
150.00 ø13 4 267 - 177.8 216.00 M12 4 222 -
160.00 M12 4 026 ISO3019-2-125-B4 350.00 M24 2 203 SAE F 177 - 2
160.00 ø13 4 033 - 216.00 ø13 4 055 -
160.00 M12 2 079 - 216.00 M16 4 078 -
180.00 M16 2 082 ISO3019-2-125-B2 224.00 M16 4 112 ISO3019 - 2 -180 B4
180
155.00 M10 4 102 - 216.00 M12 4 132 -
125 160.00 ø17 4 113 - 215.00 M22 4 148 -
200.00 M12 4 114 - 230.00 M22 4 226 -
181.20 M16 2 136 - 250.00 M20 4 028 ISO3019 - 2 -200 B4
200.00 M16 4 200 - 250.00 ø22 4 095 -
200
180.00 ø20 4 215 - 280.00 M24 2 117 -
170.00 ø18 4 237 - 230.50 M12 4 214 -
161.50 M12 4 021 - 203.2 254.00 M14 4 210 -
127 181.20 M16 2 080 SAE C 127-2 205 240.00 M16 4 133 -
161.50 M14 4 140 - 280.00 M20 4 144 ISO3019 - 2 -224 B4
224
165.00 ø11 4 054 - 280.00 ø22 4 205 -
150.00 M12 4 068 - 310.00 M24 4 238 -
250
130 181.20 M16 2 085 - 315.00 M20 4 282 ISO3019 - 2 -250 B4
165.00 M12 4 124 - 355.00 M16 4 233 -
275
165.00 M14 4 135 - 355.00 ø18 4 281 -
“-”: configuration out of ISO & SAE Standard “-”: configuration out of ISO & SAE Standard

49 Bell-Housing
Bell-Housing 50
 Bell-Housing

LMG series
IEC electric motor range from size 63 up to size 225

51 Bell-Housing
LMG GENERAL INFORMATION

Technical data

Bell-Housing - IEC electric motor range from size 63 up to size 225

Materials Temperature
- Bell-housing: Pressure die casting Aluminium From -30 °C to +80 °C
- Center ring: Galvanized Steel
- Gasket: Special paper - Guarnital

Note
Compatibility with fluids For temperatures outside this range, contact
MP Filtri Technical and Sales Department
Modular bell-housing components compatible for use with:
- Mineral oils types HH-LL-HM-HR-HV-HC, to ISO 6743/4 standard
- Water based emulsions types HFAE-HFAS, to ISO 6743/4 standard
- Water glycol type HFC, to ISO 6743/4 standard: ask for anodized version

Special Applications
Any applications not covered by the normal indications
contained in this catalogue must be evaluated and approved
by MP Filtri Technical and Sales Department

IEC Electric motors

Bell-Housing European standard size German standard size IEC Motors
size 0.5 1 2 3 3.5 4 ZB ZF ZG size
LMG140 IEC 63 ø 140 - ø 11x23
LMG160 IEC 71 ø 160 - ø 14x30
LMG200 IEC 80 ø 200 - ø 19x40
LMG200 IEC 90 ø 200 - ø 24x50
LMG250 IEC 110 ø 250 - ø 28x60
LMG250 IEC 112 ø 250 - ø 28x60
LMG300 IEC 132 ø 300 - ø 38x80
LMG351 IEC 160 ø 350 - ø 42x110
LMG351 IEC 180 ø 350 - ø 48x110
LMG400 IEC 200 ø 400 - ø 55x110
LMG450 IEC 225 ø 450 - ø 60x140

Note: For specific information see pages 58 ÷ 60 “Table of Combination”

Bell-Housing 52
VERSIONS LMG

LMG *** 4S LMG *** 4E

Without centre ring allowing removal of half-coupling (which as a rule With centre ring allowing removal of half-coupling (which as a rule is
is keyed permanently to the pump shaft); motor mounting flange drilled keyed permanently to the pump shaft), motor mounting flange drilled
with 4 clearance holes + 4 threaded holes. with 4 clearance holes + 4 threaded holes.
Used normally for vertically mounted motor and pump units with pump Normally used for motor and pump units mounted horizontally on the
submerged in the oil tank. tank lid or on the machine for maximum ease of maintenance.
With this type of mounting, in effect, the hydraulic pump can be
removed without removing the motor.
The half-coupling mounted to the shaft passes through the spigot hole.

LMG *** 8S LMG *** 8E

Without centre ring allowing removal of half-coupling (which as a rule With centre ring allowing removal of half-coupling (which as a rule is
is keyed permanently to the pump shaft), motor mounting flange drilled keyed permanently to the pump shaft), motor mounting flange drilled
with 8 clearance holes. Used normally for vertically mounted motor and with 8 clearance holes.
pump units with pump submerged in the oil tank, allows greater Normally used for motor and pump units mounted horizontally on the
flexibility for directional positioning of the hydraulic pump inside the tank lid or on the machine, offers maximum ease of maintenance and
tank, according to constructional requirements. enables directional positioning of the pump.
With this type of mounting, in effect, the hydraulic pump can be removed
without removing the motor.
The half-coupling mounted to the shaft passes through the spigot hole.

53 Bell-Housing
LMG
Designation & Ordering code

COMPLETE KIT (BELL-HOUSING & COUPLINGS)

Motors identification code Configuration example: AKA02 FS200 Z 4E
Size Size Size
02 63 B3-B5 13 180 B3-B5 44 71 B14
03 71 B3-B5 16 200 B3-B5 45 80 B14
04 80 B3-B5 18 225 B3-B5 46 90 B14
05 90 B3-B5 20 250 B3-B5 48 100/112 B14
07 100/112 B3-B5 22 280 B3-B5
11 132 B3-B5 26 315 B3-B5
12 160 B3-B5 43 63 B14
Pump flange identification code
FS200 See page 55
Product revision code
Z
Versions
4S 4 through holes + 4 threaded holes, motor interface without coupling removal ring
4E 4 through holes + 4 threaded holes, motor interface with coupling removal ring
8S 8 through holes, motor interface without coupling removal ring
8E 8 through holes, motor interface with coupling removal ring

BELL-HOUSING LMG
Bell-Housing series and size Configuration example: LMG140 M FS200 4E DI
LMG140 LMG250 LMG450
LMG141 LMG251 LMG550
LMG160 LMG300 LMG660
LMG161 LMG350
LMG200 LMG351
LMG201 LMG400
Product revision code
M
Pump flange identification code
FS200 See page 55
Versions
4S 4 through holes + 4 threaded holes, motor interface without coupling removal ring
4E 4 through holes + 4 threaded holes, motor interface with coupling removal ring
8S 8 through holes, motor interface without coupling removal ring
8E 8 through holes, motor interface with coupling removal ring
Options
DI Drain hole + inspection hole
AN Black anodized finish
SA Motor interface with clearance holes
Pxx Customer specification

COUPLING KIT
Motors identification code Configuration example: AKG02 FS200 Z
Size Size
02 63 B3-B5 13 180 B3-B5
03 71 B3-B5 43 63 B14
04 80 B3-B5 44 71 B14
05 90 B3-B5 45 80 B14
07 100/112 B3-B5 46 90 B14
11 132 B3-B5 48 100/112 B14
12 160 B3-B5
Pumps flange identification code
FS200 See page 55
Product revision code
Z
Note:
- Bell-Housings with DI options are supplied complete with threaded closure plug.
- Bell-Housing with 4E/8E version are supplied with center ring mounted.
- For product range codes see pages 58 ÷ 60
Bell-Housing 54
 LMG
Dimensions

Spigot
hole Hole

Key
d

Designation of pump flange and shaft

Pump Spigot Dimensions Pump flange Shaft Pump half-coupling
group hole A B C Hole code d Key type code
22.0 25.5 66.0 - M6 FS05M 6.0 2.0 parallel FS05M
05
22.0 25.5 66.0 - M6 FS05C 7.0 2.0 parallel FS05C
25.4 26.2 72.0 52.0 M6 FS100 9.7 2.4 tapered 1:8 FS100
1 30.0 24.5 73.0 56.0 M6 FS1M0 12.0 3.0 parallel FS1C0
30.0 24.5 73.0 56.0 M6 FS1M0 13.9 3.0 tapered 1:8 FS1M0
2 36.5 32.5 96.0 71.5 M8 FS200 17.2 3.2 - 4 tapered 1:8 FS200
50.8 43.0 128.0 98.5 M8 FS25T 22.2 4.0 tapered 1:8 FS300
50.8 42.0 128.0 98.5 M10 FS300 22.2 4.0 tapered 1:8 FS300
3
50.8 43.0 128.0 98.5 M10 FS3M0 22.2 4.0 tapered 1:8 FS300
50.8 45.0 137.0 98.5 M10 FS3T0 22.2 4.0 tapered 1:8 FS300
60.0 48.5 148.0 127.0 M12 FS35M 25.6 4.76 - 5.0 tapered 1:8 FS350
3.5
60.3 49.5 149.5 114.3 M10 FS350 25.6 4.76 - 5.0 tapered 1:8 FS350
63.5 65.0 196.0 142.8 M12 FS4M0 33.3 6.35 - 7.0 tapered 1:8 FS400
4
63.5 64.3 188.0 143.0 M12 FS400 33.3 6.35 - 7.0 tapered 1:8 FS400
32.0 10.3 40.0 40.0 M8 FSZBR 9.8 2.0 tapered 1:5 FSZBR
Bosch 80.0 34.5 100.0 72.0 M8 FSZFR 16.9 3.0 tapered 1:5 FSZFR
105.0 48.0 145.0 102.0 M10 FSZGR 25.2 5.0 tapered 1:5 FSZGR

55 Bell-Housing
LMG
Dimensions

Inspection Hole 0.15

Plastic threaded plug mounted
(protection according Motor Motor
to DIN EN 292 part 2) size size
“Safety of machines” Pump Pump
size size

Drain Hole Nr.4xF

(on request)
Nr.4xP

(*) Shape valid for LMG 251

Bell-housing
IEC - Electric motors Bell-housing Dimensions [mm] On request Weight
Motor size Shaft end [d x l] code D1 D2 D3 D4 H1 H2 F P H3 D6 [kg]
63 - B14 11x23 LMG090 60 75 90 63 60 7 - 6 40 1/2” 0.30
71 - B14 14x30 LMG105 70 85 105 74 67 8 - 7 40 1/2” 0.35
80 - B14 19x14 LMG120 80 100 120 84 87 9 - 7 45 1/2” 0.40
63 - B3/B5 11x23 LMG140 95 115 140 100 60 13 M8 9 40 1/2” 0.35
63 - B3/B5 11x23 LMG141 95 115 140 100 95 13 M8 9 50 1/2” 0.40
71 - B3/B5 14x30 LMG160 110 130 160 110 70 15 M8 9 40 1/2” 0.44
71 - B3/B5 14x30 LMG161 110 130 160 110 105 15 M8 9 50 1/2” 0.50
80 - B3/B5 19x14 LMG200 130 165 200 135 87 18 M10 11 45 3/4” 0.68
90 - B3/B5 24x50 LMG201 130 165 200 135 95 18 M10 11 50 3/4” 0.80
100-112 - B3/B5 28x60 LMG250 180 215 250 185 105 22 M12 14 70 3/4” 1.16
100-112 - B3/B5 28x60 LMG251 (*) 180 215 250 185 126 22 M12 14 70 3/4” 1.80

Bell-Housing 56
 LMG
Dimensions

Inspection Hole
Plastic threaded plug mounted
(protection according
to DIN EN 292 part 2)
“Safety of machines”

ø10

Drain Hole Nr.4xF

(on request)
Nr.4xP

Bell-housing
IEC - Electric motors Bell-housing Dimensions [mm] On request Weight
Motor size Shaft end [d x l] code D1 D2 D3 D4 H1 H2 F P H3 D6 [kg]
132 38x80 LMG300 230 265 300 235 145 23 M12 14 80 1” 2.55
160 42x110 LMG351 250 300 350 255 179 31 M16 18 100 1” 4.90
180 48x110 LMG351 250 300 350 255 179 31 M16 18 100 1” 4.90

57 Bell-Housing
LMG TABLE OF COMBINATION

IEC Motors B3/5 - standard gear pump

IEC - Electric motors Pump Components
Motor Shaft end identification Bell-Housing Motor half-coupling Spider Pump half-coupling Complete Complete
size [d x l] code code code code code kit code coupling kit code
FS05M LMG140MFS05M4S SGEA01FS05M AKA02FS05MZ4S AKG02FS05MZ
FS05C LMG140MFS05M4S SGEA01FS05C AKA02FS05CZ4S AKG02FS05CZ
FS100 LMG140MFS1004S/4E SGEA01FS100 AKA02FS100Z4S/4E AKG02FS100Z
63 11x23 SGEA01M01019FG EGE 0
FS1C0 LMG140MFS1M04S/4E SGEA01FS1CO AKA02FS1C0Z4S/4E AKG02FS1C0Z
FS1M0 LMG140MFS1M04S/4E SGEA01FS1MO AKA02FS1M0Z4S/4E AKG02FS1M0Z
FSZBR LMG140MFSZBR4S SGEA01FSZBR AKA02FSZBRZ4S AKG02FSZBRZ
FS05M LMG160MFS05M4S SGEA01FS05M AKA03FS05MZ4S AKG03FS05MZ
FS05C LMG160MFS05M4S SGEA01FS05C AKA03FS05CZ4S AKG03FS05CZ
FS100 LMG160MFS1004S/4E SGEA01FS100 AKA03FS100Z4S/4E AKG03FS100Z
71 14x30 SGEA01M02028FG EGE 0
FS1C0 LMG160MFS1M04S/4E SGEA01FS1C0 AKA03FS1C0Z4S/4E AKG03FS1C0Z
FS1M0 LMG160MFS1M04S/4E SGEA01FS1M0 AKA03FS1M0Z4S/4E AKG03FS1M0Z
FSZBR LMG160MFSZBR4S SGEA01FSZBR AKA03FSZBRZ4S AKG03FSZBRZ
FS05M LMG200MFS05M4S SGEA01FS05M AKA04FS05MZ4S AKG04FS05MZ
FS05C LMG200MFS05M4S SGEA01FS05C AKA04FS05CZ4S AKG04FS05CZ
FS100 LMG200MFS1004S/4E SGEA01FS100 AKA04FS100Z4S/4E AKG04FS100Z
SGEA01M03048FG EGE 0
FS1C0 LMG200MFS1M04S/4E SGEA01FS1C0 AKA04FS1C0Z4S/4E AKG04FS1C0Z
80 19x40
FS1M0 LMG200MFS1M04S/4E SGEA01FS1M0 AKA04FS1M0Z4S/4E AKG04FS1M0Z
FSZBR LMG200MFSZBR4S SGEA01FSZBR AKA04FSZBRZ4S AKG04FSZBRZ
FS200 LMG201MFS2004S/4E SGEA21FS200 AKA04FS200Z4S/4E AKG04FS200Z
SGEA21M03048FG EGE 2
FSZFR LMG201MFSZFR4S SGEA21FSZFR AKA04FSZFRZ4S AKG04FSZFRZ
FS05M LMG200MFS05M4S SGEA01FS05M AKA05FS05MZ4S AKG05FS05MZ
FS05C LMG200MFS05M4S SGEA01FS05C AKA05FS05CZ4S AKG05FS05CZ
FS100 LMG200MFS1004S/4E SGEA01FS100 AKA05FS100Z4S/4E AKG05FS100Z
SGEA01M04048FG EGE 0
90 24x50 FS1C0 LMG200MFS1M04S/4E SGEA01FS1C0 AKA05FS1C0Z4S/4E AKG05FS1C0Z
FS1M0 LMG200MFS1M04S/4E SGEA01FS1M0 AKA05FS1M0Z4S/4E AKG05FS1M0Z
FSZBR LMG200MFSZBR4S SGEA01FSZBR AKA05FSZBRZ4S AKG05FSZBRZ
FS200 LMG201MFS2004S/4E SGEA21FS200 AKA05FS200Z4S/4E AKG05FS200Z
SGEA21M04048FG EGE 2
FSZFR LMG201MFSZFR4S SGEA21FSZFR AKA05FSZFRZ4S AKG05FSZFRZ
FS100 LMG250MFS1004S SGEA21FS100 AKA07FS100Z4S AKG07FS100Z
FS1C0 LMG250MFS1M04S SGEA21FS1C0 AKA07FS1C0Z4S AKG07FS1C0Z
FS1M0 LMG250MFS1M04S SGEA21FS1M0 AKA07FS1M0Z4S AKG07FS1M0Z
FSZBR LMG250MFSZBR4S SGEA21FSZBR AKA07FSZBRZ4S AKG07FSZBRZ
100 FS200 LMG250MFS2004S/4E SGEA21FS200 AKA07FS200Z4S/4E AKG07FS200Z
28x60 SGEA21M05055FG EGE 2
112 FSZFR LMG250MFSZFR4S SGEA21FSZFR AKA07FSZFRZ4S AKG07FSZFRZ
FS25T LMG251MFS25T4E SGEA21FS300 AKA07FS25TZ4E AKG07FS300Z
FS300 LMG251MFS3004E SGEA21FS300 AKA07FS300Z4E AKG07FS300Z
FS3M0 LMG251MFS3M04E SGEA21FS300 AKA07FS3M0Z4E AKG07FS300Z
FS3T0 LMG251MFS3T04E SGEA21FS300 AKA07FS3T0Z4E AKG07FS300Z
FS100 LMG300MFS1004S SGEA31FS100 AKA11FS100Z4S AKG11FS100Z
FS1C0 LMG300MFS1M04S SGEA31FS1C0 AKA11FS1C0Z4S AKG11FS1C0Z
FS1M0 LMG300MFS1M04S SGEA31FS1M0 AKA11FS1M0Z4S AKG11FS1M0Z
FSZGR LMG300MFSZGR4S SGEA31FSZGR AKA11FSZGRZ4S AKG11FSZGRZ
FS200 LMG300MFS2004S/4E SGEA31FS200 AKA11FS200Z4S/4E AKG11FS200Z
FSZFR LMG300MFSZFR4S SGEA31M06077FG EGE 3 SGEA31FSZFR AKA11FSZFRZ4S AKG11FSZFRZ
132 38x80
FS25T LMG300MFS25T4S/4E SGEA31FS300 AKA11FS25TZ4S/4E AKG11FS300Z
FS300 LMG300MFS3004S/4E SGEA31FS300 AKA11FS300Z4S/4E AKG11FS300Z
FS3M0 LMG300MFS3M04S/4E SGEA31FS300 AKA11FS3M0Z4S/4E AKG11FS300Z
FS3T0 LMG300MFS3T04S/4E SGEA31FS300 AKA11FS3T0Z4S/4E AKG11FS300Z
FS35M LMG300MFS35M4S/4E SGEA31FS350 AKA11FS35MZ4S/4E AKG11FS350Z
FS350 LMG300MFS3504S/4E SGEA31FS350 AKA11FS350Z4S/4E AKG11FS350Z

Note:
- For bell-housing dimensions see pages 56-57.
- For coupling dimensions see “Half-couplings” section on pages 26-27.

Bell-Housing 58
TABLE OF COMBINATION LMG
IEC Motors B3/5 - standard gear pump
IEC - Electric motors Pump Components
Motor Shaft end identification Bell-Housing Motor half-coupling Spider Pump half-coupling Complete Complete
size [d x l] code code code code code kit code coupling kit code
FSZGR LMG351MFSZGR4S SGEA51FSZGR AKA12FSZGRZ4S AKG12FSZGRZ
FS200 LMG351MFS2004S SGEA51FS200 AKA12FS200Z4S AKG12FS200Z
FSZFR LMG351MFSZFR4S SGEA51FSZFR AKA12FSZFRZ4S AKG12FSZFRZ
FS25T LMG351MFS25T4S/4E SGEA51FS300 AKA12FS25TZ4S/4E AKG12FS300Z
160 42x110 FS300 LMG351MFS3004S/4E SGEA51M07109FG EGE 5 SGEA51FS300 AKA12FS300Z4S/4E AKG12FS300Z
FS3M0 LMG351MFS3M04S/4E SGEA51FS300 AKA12FS3M0Z4S/4E AKG12FS300Z
FS3T0 LMG351MFS3T04S/4E SGEA51FS300 AKA12FS3T0Z4S/4E AKG12FS300Z
FS35M LMG351MFS35M4S/4E SGEA51FS350 AKA12FS35MZ4S/4E AKG12FS350Z
FS350 LMG351MFS3504S/4E SGEA51FS350 AKA12FS3504ZS/4E AKG12FS350Z
FSZGR LMG351MFSZGR4S SGEA51FSZGR AKA13FSZGRZ4S AKG13FSZGRZ
FS200 LMG351MFS2004S SGEA51FS200 AKA13FS200Z4S AKG13FS200Z
FSZFR LMG351MFSZFR4S SGEA51FSZFR AKA13FSZFRZ4S AKG13FSZFRZ
FS25T LMG351MFS25T4S/4E SGEA51FS300 AKA13FS25TZ4S/4E AKG13FS300Z
180 48x110 FS300 LMG351MFS3004S/4E SGEA51M08109FG EGE 5 SGEA51FS300 AKA13FS300Z4S/4E AKG13FS300Z
FS3M0 LMG351MFS3M04S/4E SGEA51FS300 AKA13FS3M0Z4S/4E AKG13FS300Z
FS3T0 LMG351MFS3T04S/4E SGEA51FS300 AKA13FS3T04ZS/4E AKG13FS300Z
FS35M LMG351MFS35M4S/4E SGEA51FS350 AKA13FS35MZ4S/4E AKG13FS350Z
FS350 LMG351MFS3504S/4E SGEA51FS350 AKA13FS350Z4S/4E AKG13FS350Z
FS200 LMG400MFS2004E SGEA51FS200 AKA16FS200Z4S AKG16FS200Z
FS300 LMG400MFS3004E SGEA51FS300 AKA16FS300Z4E AKG16FS300Z
FS3M0 LMG400MFS3M04E SGEA51FS300 AKA16FS3M0Z4E AKG16FS300Z
200 55x110 FS35M LMG400MFS35M4E SGEA51M09109FG EGE 5 SGEA51FS350 AKA16FS35MZ4E AKG16FS350Z
FS350 LMG400MFS3504E SGEA51FS350 AKA16FS350Z4E AKG16FS350Z
FSZFR LMG400MFSZFR4S SGEA51FSZFR AKA16FSZFRZ4E AKG16FSZFRZ
FSZGR LMG400MFSZGR4S SGEA51FSZGR AKA16FSZGRZ4E AKG16FSZGRZ
FS300 LMG450MFS3004E SGEG60FS300 AKA18FS300Z4E AKG18FS300Z
FS3MO LMG450MFS3MO4E SGEG60FS300 AKA18FS3M0Z4E AKG18FS300Z
225 60x140 FS35M LMG450MFS35M4E SGEG60M10110 EGE 6 SGEG60FS350 AKA18FS35MZ4E AKG18FS350Z
FS350 LMG450MFS3504E SGEG60FS350 AKA18FS350Z4E AKG18FS350Z
FSZGR LMG450MFSZGR4S SGEG60FSZGR AKA18FSZGRZ4E AKG18FSZGRZ
FS300 LMG550MFS3004E SGEG60FS300 AKA20FS300Z4E AKG20FS300Z
FS3MO LMG550MFS3MO4E SGEG60FS300 AKA20FS3M0Z4E AKG20FS300Z
250 65x140 FS35M LMG550MFS35M4E SGEG60M11140 EGE 6 SGEG60FS350 AKA20FS35MZ4E AKG20FS350Z
FS350 LMG550MFS3504E SGEG60FS350 AKA20FS350Z4E AKG20FS350Z
FSZGR LMG550MFSZGR4S SGEG60FSZGR AKA20FSZGRZ4E AKG20FSZGRZ
FS300 LMG550MFS3004E SGEG80FS300 AKA22FS300Z4E AKG22FS300Z
FS3MO LMG550MFS3MO4E SGEG80FS300 AKA22FS3M0Z4E AKG22FS300Z
280 75x140 FS35M LMG550MFS35M4E SGEG80M12140 EGE 8 SGEG80FS350 AKA22FS35MZ4E AKG22FS350Z
FS350 LMG550MFS3504E SGEG80FS350 AKA22FS350Z4E AKG22FS350Z
FSZGR LMG550MFSZGR4S SGEG80FSZGR AKA22FSZGRZ4E AKG22FSZGRZ
FS300 LMG660MFS3004E SGEG80FS300 AKA26FS300Z4E AKG26FS300Z
FS3MO LMG660MFS3MO4E SGEG80FS300 AKA26FS3M0Z4E AKG26FS300Z
315 80x170 FS35M LMG660MFS35M4E SGEG80M13170 EGE 8 SGEG80FS350 AKA26FS35MZ4E AKG26FS350Z
FS350 LMG660MFS3504E SGEG80FS350 AKA26FS350Z4E AKG26FS350Z
FSZGR LMG660MFSZGR4S SGEG80FSZGR AKA26FSZGRZ4E AKG26FSZGRZ

Note:
- For bell-housing dimensions see pages 56-57.
- For coupling dimensions see “Half-couplings” section on pages 26-27.

59 Bell-Housing
LMG TABLE OF COMBINATION

IEC Electric motors B14 mounting

IEC - Electric motors Pump Components
Motor Shaft end identification Bell-Housing Motor half-coupling Spider Pump half-coupling Complete Complete
size [d x l] code code code code code kit code coupling kit code
FS05M LMG090MFS05M4E SGEA00FS05M AKA43FS05MZ4E AKG43FS05MZ
FS05C LMG090MFS05M4E SGEA01FS05C AKA43FS05CZ4E AKG43FS05CZ
63 11x23 FS100 LMG090MFS1004E SGEA01FS100 AKA43FS100Z4E AKG43FS100Z
SGEA01M01021FG EGE0
FS1C0 LMG090MFS1M04E SGEA01FS1C0 AKA43FS1C0Z4E AKG43FS1C0Z
FS1M0 LMG090MFS1M04E SGEA01FS1M0 AKA43FS1M0Z4E AKG43FS1M0Z
FSZBR LMG090MFSZBR4E SGEA01FSZBR AKA43FSZBRZ4E AKG43FSZBRZ
FS05M LMG105MFS05M4E SGEA01FS05M AKA44FS05MZ4E AKG44FS05MZ
FS05C LMG105MFS05M4E SGEA01FS05C AKA44FS05CZ4E AKG44FS05CZ
71 14x30 FS100 LMG105MFS1004E SGEA01FS100 AKA44FS100Z4E AKG44FS100Z
SGEA01M02028FG EGE 0
FS1C0 LMG105MFS1C04E SGEA01FS1C0 AKA44FS1C0Z4E AKG44FS1C0Z
FS1M0 LMG105MFS1M04E SGEA01FS1M0 AKA44FS1M0Z4E AKG44FS1M0Z
FSZBR LMG105MFSZBR4E SGEA01FSZBR AKA44FSZBRZ4E AKG44FSZBRZ
FS05M LMG120MFS05M4E SGEA01FS05M AKA45FS05MZ4E AKG45FS05MZ
FS05C LMG120MFS05M4E SGEA01FS05C AKA45FS05CZ4E AKG45FS05CZ
FS100 LMG120MFS1004E SGEA01FS100 AKA45FS100Z4E AKG45FS100Z
SGEA01M03048FG EGE 0
80 19x40 FS1C0 LMG120MFS1M04E SGEA01FS1C0 AKA45FS1C0Z4E AKG45FS1C0Z
FS1M0 LMG120MFS1M04E SGEA01FS1M0 AKA45FS1M0Z4E AKG45FS1M0Z
FSZBR LMG120MFSZBR4S SGEA01FSZBR AKA45FSZBRZ4E AKG45FSZBRZ
FS200 LMG121MFS2004E SGEA21FS200 AKA45FS200Z4E AKG45FS200Z
SGEA21M03048FG EGE 2
FSZFR LMG121MFSZFR4S SGEA21FSZFR AKA45FSZFRZ4S AKG45FSZFRZ
FS05M LMG141MFS05M4S SGEA01FS05M AKA46FS05MZ4E AKG46FS05MZ
FS05C LMG141MFS05M4S SGEA01FS05C AKA46FS05CZ4E AKG46FS05CZ
FS100 LMG141MFS1004S/4E SGEA01FS100 AKA46FS100Z4E AKG46FS100Z
SGEA01M04048FG EGE 0
90 24x50 FS1C0 LMG141MFS1M04S/4E SGEA01FS1C0 AKA46FS1C0Z4E AKG46FS1C0Z
FS1M0 LMG141MFS1M04S/4E SGEA01FS1M0 AKA46FS1M0Z4E AKG46FS1M0Z
FSZBR LMG141MFSZBR4S SGEA01FSZBR AKA46FSZBRZ4E AKG46FSZBRZ
FS200 LMG141MFS2004S/4E SGEA21FS200 AKA46FS200Z4E AKG46FS200Z
SGEA21M04048FG EGE 2
FSZFR LMG141MFSZFR4S SGEA21FSZFR AKA46FSZFRZ4S AKG46FSZFRZ
FS05M LMG161MFS05M4S SGEA21FS05M AKA48FS05MZ4E AKG48FS05MZ
FS05C LMG161MFS05M4S SGEA21FS05C AKA48FS05CZ4E AKG48FS05CZ
FS100 LMG161MFS1004S SGEA21FS100 AKA48FS100Z4E AKG48FS100Z
100 FS1C0 LMG161MFS1M04S SGEA21FS1C0 AKA48FS1C0Z4E AKG48FS1C0Z
28x60 SGEA21M05055FG EGE 2
112 FS1M0 LMG161MFS1M04S SGEA21FS1M0 AKA48FS1M0Z4E AKG48FS1M0Z
FSZBR LMG161MFSZBR4S SGEA21FSZBR AKA48FSZBRZ4E AKG48FSZBRZ
FS200 LMG161MFS2004S/4E SGEA21FS200 AKA48FS200Z4E AKG48FS200Z
FSZFR LMG161MFSZFR4S SGEA21FSZFR AKA48FSZFRZ4S AKG48FSZFRZ

Note:
- For bell-housing dimensions see pages 56-57.
- For coupling dimensions see “Half-couplings” section on pages 26-27.

Bell-Housing 60
ACCESSORIES LMG
Dimensions
CENTER RING
Center ring Dimensions [mm]
code D1 D2 Thk.
ANC01FS100 50 25.4 1.0
ANC01FS1M0 50 30.0 1.0
ANC02FS200 72 36.5 2.0
ANC03FS200 88 36.5 2.0
ANC03FS300 88 50.8 2.5
ANC03FS350 88 60.3 2.5
ANC04FS300 115 50.8 3.5
ANC04FS350 115 60.3 3.5
ANCA001 42 22.0 1.0
ANCD005 85 50.8 2.5

Thk.

Center ring Bell-Housing size

code LMG090 LMG105 LMG120 LMG140 LMG160 LMG200 LMG250 LMG300 LMG350 LMG400 LMG450
ANC01FS100
ANC01FSM0
ANC02FS200
ANC03FS200
ANC03FS300
ANC03FS350
ANC04FS200
ANC04FS300
ANC04FS350
ANCA001
ANCD005

GASKET
Spigot
Hole Thk. hole Hole Thk.

Motor side gasket Pump side gasket

Bell-housing Seals Dimensions [mm] Pump identification Seals Dimensions [mm]
size code D1 D2 D3 Thk. Hole code code PD A B C H L Thk. Hole
LMG 120 GUM P 120 84 100 120 1 7 FS05M GUP P001 22.0 25.6 66 - 80 48 1 6.5
LMG 140 GUM P 140 96 115 140 1 9 FS100 GUP P002 25.4 26.6 72 52.4 87 67 1 6.5
LMG 160 GUM P 160 110 130 160 1 9 FS1M0 GUP P003 30.0 24.5 73 56.0 85 68 1 6.5
LMG 200 GUM P 200 145 165 200 1 11 FS200 GUP P004 36.5 32.5 96 71.5 112 88 1 8.5
LMG 250 GUM P 250 190 215 250 1 14 FS300 GUP P005 50.8 43.0 128 98.5 148 118 1 10.5
LMG 300 GUM P 300 234 265 300 1 14 FSZBR GUP P013 32.0 10.35 40 40.0 75 62 1 8.5
LMG 350 GUM P 350 260 300 350 1 18 FSZFR GUP P014 80.0 34.5 100 72.0 118 90 1 9.0

61 Bell-Housing