Scribd
Upload
63 views9 pages

Assignment 2

This document outlines an assignment for an Introduction to Mechanical Engineering course. It contains 25 questions requiring students to determine reactions, shear forces, bending moments, and member forces in beams and trusses subjected to various loads. Students must draw shear force and bending moment diagrams, and find maximum bending moments and locations. The assignment is due on March 5, 2023 and requires solving all questions in the provided order.

Uploaded by

220112034
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
63 views9 pages

Assignment 2

This document outlines an assignment for an Introduction to Mechanical Engineering course. It contains 25 questions requiring students to determine reactions, shear forces, bending moments, and member forces in beams and trusses subjected to various loads. Students must draw shear force and bending moment diagrams, and find maximum bending moments and locations. The assignment is due on March 5, 2023 and requires solving all questions in the provided order.

Uploaded by

220112034
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

ASSIGNMENT NO.

#2
Course: Introduction to Mechanical Engineering
Last Date of submission: March_05_2023
Note: Attempt all the question in the sequence as they are provided here.

1. Determine the reactions at A and B for the beams subjected to the following loads.

(a) (b)

(c) (d)

2. Determine the reactions at A for the cantilever beam subjected to the distributed and
concentrated loads.

3. Determine the reactions at A, B, and D for the pair of beams connected by the ideal
pin at C and subjected to the concentrated and distributed loads.
4. Determine the reactions at A and C for the beam subjected to the combination of point
and distributed loads.

5. Determine the reactions at A and B for the beam subjected to the distributed and
concentrated loads.

6. Determine the force and moment reactions at A for the beam which is subjected to the
distributed load shown below.
7. Draw the shear-force and bending-moment diagrams for the loaded beam and determine
the maximum moment M and its location x from the left end.

8. Determine the shear-force and bending-moment distributions produced in the beam by


the concentrated load. What are the values of the shear force and bending moment at x
= l/2?

9. Determine the shear force Vat a section B between A and C and the bending moment
M at the support A.

10. Determine the shear force V and bending moment M at a section of the loaded beam
200 mm to the right of A.
11. Determine the shear force and bending moment in the beam at a section 2 m to the right
of end A.

12. Draw the shear and moment diagrams for the beam subjected to the concentrated loads.
What are the values of the shear force and bending moment at x = 12 m?

13. Draw the shear and moment diagrams for the cantilever beam with the linear loading.
Find the maximum magnitude of the bending moment M.

14. Plot the shear and moment diagrams for the beam loaded as shown. State the maximum
magnitudes of the shear force and bending moment for the beam.
15. Draw the shear and moment diagrams for the beam loaded as shown. Specify the
maximum bending moment Mmax.

Truss: Method of Joints


16. Determine the force in each member of the loaded truss as a result of the hanging weight
W.

17. Determine the force in each member of the loaded truss.


18. Calculate the forces in members BE and BD of the loaded truss.

19. Determine the force in each member of the loaded truss.

20. Determine the force in each member of the loaded truss.


(a)

(b)

(c)

21. Determine the forces in members BC and BG of the loaded truss.


Truss: Method of Sections
22. Determine the force in member CG.

23. Determine the force in member AE of the loaded truss.


24. Determine the force in member BC of the loaded truss.

25. Determine the forces in members BC and CG.

You might also like