ACS800 Crane Drive Control
Drive which lifts your crane Drive which lifts your crane efficiency to new heights efficiency to new heights
www.abb.com/drives&motors
ACS800 Crane Drive Control
Standard, cost effective crane drive with built-in safety and performance
www.abb.com/drives&motors
Software Functions
Control Functions
For optimised performance
Safety Functions
For excellent operational safety
www.abb.com/drives&motors
Control Functions
Control Interface Logic Handling Reference Handling Speed and Torque Control Torque Memory Power Optimisation Limit Switch Supervision Master Follower Speed Correction Speed monitor
www.abb.com/drives&motors
Software hierarchy for ACC
Master Follower
Application macro
99.2
DDCS CH2 communication
Crane
64.1
M/F Control
64.1
Stand alone
64.10
Fieldbus
Stand alone
64.10
Fieldbus
Joystick Step radio Radio FB joystick* Motor Pot. Step joyst.
Joystick Step radio Radio FB joystick* Motor Pot. Step joyst.
www.abb.com/drives&motors
Control Functions: Joystick
Control Interface: Joystick
Zero position + direction contacts Stepped (4 levels) or potentiometer speed reference 0-10V. 4 wire potentiometer with centre connection required
www.abb.com/drives&motors
Control Functions: Pendant
Control Interface:Pendant controller
Direction commands Speed reference given with motor potentiometer function
www.abb.com/drives&motors
Control Functions: Radio Controller
Control Interface:Radio Controller
Hardwired I/O-connection between receiver and drive Analogue reference from receiver +10V Direction commands
Radio Controller
www.abb.com/drives&motors
Control Functions: Fieldbus
Fieldbus Interfaces
Two types of adapters available
DDCS link adapters placed outside the drive CANopen ControlNet DeviceNet Interbus-S Modbus Modbus Plus Profibus Ethernet module for remote control&diagnostics (not a fieldbus) New type of modules placed inside the drive Only profibus available New protocols coming later Advant Module bus needs RDCO-01 adapter
www.abb.com/drives&motors
Control Functions: Logic Handling
Logic Handling & 1
> START Supervises starting and stopping of the drive Makes sure that motor is magnetised before start Takes care of starting sequences in different modes
&
www.abb.com/drives&motors
Control Functions: Reference Handling
Reference Handling
Individual setting of acceleration/deceleration ramp time for both directions Smooth load handling Reduces crane structural loads Optimises load cycle Customises performance
Ref.
t
www.abb.com/drives&motors
Control Functions: Speed&Torque Control
Speed and Torque Control
Ref. + Act. Ensures minimum variation of speed under load Load independent performance Smooth load handling Start and stop times independent of load DTC makes performance outstanding compared to other manufacturers
PID
M
PG
For hoist applications
www.abb.com/drives&motors
Control Functions: Torque memory
Torque Memory
Minimises the risk of load drop on hoist drives Safe load handling without jerks No risk of jamming between load and floor
www.abb.com/drives&motors
Control Functions: Power Optimisation
Power Optimisation
Allowed speed nTmin Ensures maximum hoist speed relative to the load Lowest possible cycle time Optimises the crane capacity Automatic start-up procedure for setting related parameters
nTmax
T min Actual load
Tmax
www.abb.com/drives&motors
Control Functions: Limit Switches
Y
Limit Switch Supervision
To ensure the crane operates within a safe working envelope All necessary logic is in the drive Safe operation with both pre and end limits Motion outbound from limit area can happen with full speed
www.abb.com/drives&motors
Control Functions: Master/Follower
Master Follower
Supply network
~
M
DDCS optocable
~
M
Gear box
Load sharing of two motor drives on the same shaft For motions where requirements are too high for one motor or when redundancy is required Also for application where two motors are coupled through a rigid structure Multiple slaves possible
Output shaft
www.abb.com/drives&motors
Control Functions: Electrical shaft
Electrical Shaft
Supply network
~
M
DDCS optocable
~
M
Automatic correction of position error when used in synchronised operation Adjustable response for position error (P-controller) Pulse encoders must be used Two drives can be connected together
Gear box
Gear box
Synchronized motion
www.abb.com/drives&motors
Safety Functions
Mechanical Brake Control Torque Proving Fast Stop Torque Monitor Fault Handling
www.abb.com/drives&motors
Safety Functions: Brake Control
Mechanical Brake Control
ACS 800 Crane Drive DO DI
Brake Voltage
Brake
Controls opening and closing of the brakes Total control of brake performance Brake fault generated if logic notices discrepancy between control and status Adjustable parameters for different response times Possible to use internal brake feedback
Aux. Contact of the brake
www.abb.com/drives&motors
Safety Functions: Torque proving
Torque Proving
Ensures that the motor is able to produce sufficient torque Checks the cabling and connections
T=?
www.abb.com/drives&motors
Safety Functions: Fast stop
Fast Stop
Stops the hoist as fast as possible when overloaded or when slack rope occurs Mechanical overloads Slack rope Movement is possible with reduced speed in the opposite direction of the fault
!!!
www.abb.com/drives&motors
Safety Functions: Torque Monitoring
Torque Monitor
Reference speed = Actual speed
Supervises the correlation between speed ordered and actual motor speed Prevents starting in wrong direction due to wind Trips the drive if overloaded or mechanical fault occurs Adjustable parameters Allows difference during acceleration/deceleration
www.abb.com/drives&motors
Safety Functions: Fault Handling/logging
Fault Handling/logging
Latest faults saved to fault logger Logger can be read through control panel, drives window, upper controller, ethernet.. Also 2 dataloggers available in ACS 800 to provide more info from fault situation Dataloggers can be triggered also to monitor other events, not just faults
Fault
1 2 3 4
www.abb.com/drives&motors
ACS 800 Crane Drive Control
Ready-to-use with proven modular crane functionality Easy installation and start-up reduces time and cost Smoothen crane operation and shorter cycle times Low maintenance cost and longer mechanical life time Skilled local service engineers for ACS 800 Crane Drive Selected with standard option code +N652
The safe and cost-effective crane drive
www.abb.com/drives&motors
