Training Material of MS08PA Chassis

Stam Wu
2014 8 22
2014.8.22

1
 Table of Contents Page
 Interface Introduction…………………………………………………………….……...3
 Main Chip Introduction………………………………………………………….……....4
Introduction 4
 Key Components Introduction ………………………………………….………….….5
 Key Components List………………………………………………………………..…..6
 Signal Flow Diagram……………………………………………………………….…….7
 Power supply flow………………………………………………………………………..8
 I²C Bus Block Diagram……………………………………………………………….…10
 Key test point………………………………………………………………….………...11
 Unit Circuit Analysis and Testing ……………………………………………….……18
18
 Trouble Shooting…………………………………………………………………….......24
 Software update by USB …………………………………………………………….....27
 Software update by Network …………………………………………………………..31
 Enter factory menu method and system reset method……………………………33
 Other question………………………………………………………………………….…35
2
Interface Introduction LED IR and
Cable KEY
Board
Speaker
socket

USB2 0
USB2.0

Lvds socket

Y(AV)/PB
/PR in

Audio in

SPDIF

USB2.0
UART

HDMI3
Power Supply Network Tuner Audio
HDMI1 HDMI2 /MHL
Socket(110V~220V) Port OUT

3
Main Chip Introduction
The MSD6308RT is MStar`s most up-to-date system-on-chip flagship for flat panel
integrated digital television products .Building on the success of MStar’s current
solutions the MSD6308RT hosts the most advanced picture processing engine
solutions, engine,
MStarACEPRO, for all the Experts in various fields of TV video quality tuning to
develop the state-of-the-art TV and DTV system.
High level of integration: The MSD6308RT integrates DTV/multi-media all –purpose
AV decoder ,ISDB-T demodulator, VIF demodulator and Sound/Video processor into
a single
i l d device.
i Thi
This allows
ll the
h overallll BOM to b
be reduced
d d significantly
i ifi l making
ki the
h
MSD6308RT a very cost effective multi-media DTV solution.
Rich Features for High Value Products: The MSD6308RT enables feature-rich
feature rich
products that bring differentiation to the iDTV market. BY the use of AV decoder
capable of decoding a plethora of high definition content with Ethernet . USB 2.0
connectivity and a powerful CPU and advanced graphic engine, an MSD6308RT
based system can provide a high quality networking application and media-center
experience.
i
4
Key Components Introduction
Photo LED
Switch
S i h coupler driver
Transformer
Amplifier

Heat sink
for U175
MOSFET 5VSTB to
3.3VSTB U174
5V to AVDD
Commutate _DDR 1.5V
Capacitor 5VSTB TO 5V U172
Line
5V to 3.3V
Filter
Main IC NAND
UD60
UD90
Y 5V to
12V to 5V
Vcck
Capacitor
p 1 18v
1.18v

Y U401 MHL
Capacitor Current
U201 Limit IC
5V to 3.3V
X
U300
Capacitor Ethernet Filter

Pri.Fuse Line Filter

5
Key Components List
locatio
Part No
No. Component Type / Model
n
13-0B2273-XXB Power IC Power IC U901

13-AO1284-PIB
O 12V tto 5V supply
l IC
C DC-DC
C C UD90

13-AS1117-33B 5V STB to 3.3VSTB LDO DC-DC U175

13 AS1117 33B
13-AS1117-33B 5V to 3
3.3V
3V LDO DC-DC
DC DC U172

13-AZ1117-18BT1 5V to 1.5V LDO DC-DC U174

13-AZ1117-33B 5V to TU_3.3V LDO DC-DC U201

13-FHMT29-4GB memory 4G FLASH U501(CPP)

13-MN6308-RTB MAIN IC MSD6308RT-YQJ U700

13-MP2143-00B 5V to 1.1V DC-DC IC UD60

13 MP3398 AGB
13-MP3398-AGB LED driver IC DC
DC-DC
DC U970

13-RT9728-00B SWITCH IC POWER SWITCH U401

13-TPA311-D2B Amplifier TPA3113D2 U800

6
Signal Flow Diagram

Panel

LVDS
Transimiter
TPA3113D

SPI
DDR FLASH
Y(AV)/PB/PR
MSD6308RT
A di iin
Audio
Key
IR

SPDIF
Audio out
CABLE
Network FAT / FAT-
FAT+ FAT (ATV)
ANATENA
D+ / D-

D+ / D-

RX+/RX-
(ATV/DTV)
HDMI2
HDMI1

HDMI3
USB

USB

7
Power Supply Block Diagram

8
Power Supply Flow

52v

tran
Pow
nsform
wer

9
I²C Bus Block Diagram

HDMI1_SC
L
HDMI1_SD
HDMI1
A
TU1_SC
HDMI2_SC
L TU102
L
HDMI2_SD TU1_SD
HDMI2 MS08PA A Tuner
A

HDMI3_SC
L
HDMI3_SD
HDMI3
A

10
The Block of Power supply

1.AC Input and EMI

Filter
4 2.The main control
5
loop of primary.

((MOSFET,Capacitor
, p
and Transformer)
3.12V Output
2 3 Rectifier Diode
and Capacitor
4.53V Output
1 Rectifier Diode
andd Capacitor
i
5.LED Driver Loop

Attention: The primary of power supply is high voltage, please do not

touchh any component.
11
The Key test point--Power supply

3 1.12V test point

2 2.53V test point

3.LED Voltage
1 test point
p
4 4.GND

12
The Key Test Point of 12V to 5V

12V

12V to 5VSTB

UD90
12V to 5V
Test point
13
The Key Test Point of 5V--1v5

Test point
U174
5V to 1_5V

14
The Key Test Point of 5V—Vcck

UD60

Test point

15
The Key Test Point of 5V--3V3

U172

Test point

16
The Key Test Point of MHL 5V

U401
MHL 5V

17
Unit Circuit Analysis and Testing
a Reset Circuit Analysis and Testing
a.
Reset=3.3V
Normal=0V

Test point

High level is reset.

When 3V3SB comescomes, Because the impedance of D502 is lower than the
impedance of R506，the C503 is fast to saturation, Q501 turns on. TV reset.
Then after a moment,C504 has been charged, pole B of Q501 gets high
level,Q501 turns off, pole C of Q501gets low level. Reset process finishes.
When the TV is standby，the STB_RST from the IO of the main chip MSD6308RT
gives low level, TV will not reset。
When the TV is AC off，the power 12V steps down to 8.3V，The “B” pole of Q502
is 2
2.7V,Q502
7V Q502 turns on on, TV will reset
reset. Reset time is determined by the time of
3.3VSB maintains high level after 12V dropping down.
18
The process of turning on:
Measured the MCU_RESET time is 108ms， the test waveform is below：

Channel 1 3.3VSB, Channel 2 MCU_RESET

19
P
Process off turning
t i off:ff
Measured the MCU_RESET time is 75.6ms,the test Power Reset waveform is below：

Channel 1 is12V, Channel 2 is3.3VSB,Channel 3 is MCU_RESET

20
b. AMP_Mute Circuit

Mute Circuit
K18 of U700 low levelQ801 cuts off, SD HIGHUnmute
K18 of U700 high levelQ801 turns on, SD LOWMute

When 12Vcomes,, it charges

g C835
through R801,Q802 turns on Q801
turns on  SD LOW  Mute
This is POWER ON MUTE.
Mute: SD=3.77V

Unmute:SD=0V

21
C. LVDS Power Supply Circuit

Vc=2.81V

Vb 1 36V
Vb=1.36V

Ve=0.75V

Pin D6 of
U700

PinD6 of U700 high levelQ506 turns on

on, pole c of Q506
low level  Q505 turns on PANEL_VCC=12V
PinD6 of U700 low levelQ506 cuts off, pole c of Q506
high level  Q505 cuts off PANEL_VCC=0V

22
d. Audio Output Circuit

This is CLASS D Amplifier。

PIN 10 is the POWER IIMIT.

Selection of Gain

23
Trouble Shooting

Not start
Check power No Is Power board 3.3V
board STB, 12V normal?

YES Only3.3V Yes

Check if every DC-DC

Shift module has
No Check every
Check if main chip output. Does main IC have DC-DC module
power supply
p pp y or not
Output Pow
Pow-ON,
ON Dim,
Dim
BL-ON Signal to Yes
power board Main IC reset signal
No Check the U700(main IC)
Peripheral components
/ upgrade main software / IIC bus signal
check whether it connect
ground well /
Check UART LOG Crystal work or not

Yes

Replace U501/U700

24
Trouble Shooting

Abnormal Picture

Abnormal picture To check which source Abnormal picture

in some of source has abnormal picture in all source

Check the relevant U700

signal source Check the circuit
Problem between U700 to
circuit.
panel

TV, AV, YPbPr, Check the row-resistor, Check the LVDS

HDMI, VGA Replace cap. and copper of connector and T-con
U700 circuit is OK? board and panel.

Check peripheral
components of U700

25
Trouble Shooting
Abnormal Sound or No Sound

Abnormal sound To check which source

Abnormal sound in all source
source.
in some of source. has abnormal sound.

Check the waveform of P104

P104. Y Check
Check the input Y OK? Speakers.
coupling circuit of
U800. OK? N
Check the
Check the status of IIS. Y status of U800:
N OK?
AMP_VCC,
Check the relevant mute, reset. OK?
N
signal source
circuit. Check the status N Check the output coupling
of U01A: VDD, circuit of U700. OK?
control signal.
Replace
Y U800.
Replace
Replace U700
U800.

26
Software update by USB

A、Normally upgrading：

MS08upgrade.bin ；
1)You need get a update file like: “MS08upgrade.bin”；

2)Directly copy this “MS08upgrade.bin” file into the root directory

of USB disk.

3)Insert USB to TV；

4)Press Remote Control key “MENU” to display main menu；

5)Select “settings” and press “OK” key to enter the settings

submenu；

6)Select “Software Update” and press “OK” key to enter the

S ft
Software Update
U d t submenu；
b

7)Select “By USB” and press “OK” key and the TV set will search
upgrade files
files。
27
8)
If new software found, select “Confirm” and press “OK” key to
Upgrade software
Illustrate as blow:

28
9)The TV set will restart and begin to upgrade software
Illustrate as blow:

29
B、Forcibly
y upgrading：
pg g

1)You need get a update file like: “MS08upgrade.bin”

2)Directly copy this “MS08upgrade.bin” file into the root directory

of USB disk

3)) Disconnect the power cord

4) Insert USB to TV and keep pressing the power key of key

b d and
board d connectt th
the power cord,
d TV will
ill auto
t upgrade
d after
ft 3 3s
Illustrate as blow:

30
Software update by network:

1)Make your TV set connect to network

2) Press Remote Control key “MENU” to display main menu

3)Select
) “settings”
g and p
press “OK” keyy to enter the settings
g submenu

4)Select “Software Update” and press “OK” key to enter the

Software Update
p submenu

5)Select “By network” and press “OK” key to enter the update submenu

6)If new software is detected ,you can update software by selecting “Yes”
and press “OK” key

31
Illustrate as blow:

32
Enter Factory menu method

Follow the below steps to pop-up the Factory Menu in case of

“Factory Hotkey” is disable:
- press Remote
R t C
Control
t l kkey “MENU” to
t display
di l main i menu
- Select “Picture” and press “OK” key to enter the picture submenu
- Select “Contrast” item
- press the subsequence Remote Control keys “9” 9 , “7”
7 , “3”
3 and “5”
5
Press Remote Control key “Return” To pop-up the Factory Menu in
case of “Factory Hotkey” is enable.
The status of “Factory
Factory Hotkey”
Hotkey can be changed in Factory Menu
->Factory Hotkey
Press Remote Control “OK” key to enter the submenu.
Press Remote Control “Menu”
Menu key to go back to the root menumenu.
Press Remote Control “Right” or “Left” key to change the values.
Press Remote Control “OK” key run the function.
Press Remote Control “Exit”
Exit key exit the factory menu.

33
System reset method

Enter Factory Menu

-Select “NVM reset” item
-Press
Press Remote Control key “Right”,
Right , TV will reset system data.
Illustrate as blow:

34
Other question

1、If replaced a new FLASH or FLSAH’s data lossed, how to update online?

This is no way to update online。

2、When the project ID is wrong，how to change it？

There are two ways to change the project ID

ID。First，
First By entering the
factory menu mode to change project ID。Secend，By remote change the
project ID：press Digital key 062598+menu+0**。“0**”is the project ID。
If the project ID is 5
5，you
you should input 005
005.

3、HDCP KEY storage in which IC? How to conduct online upgrade?

HDCP KEY storage in Nand flash。 This is no way to update online , just to
update by USB.
4、User data, project ID, Network ID storage , Mac Address，Device Id in which IC?

storage in Nand flash. This is no way to update online .

35