Data sheet 6ES7132-6BH01-0BA0

SIMATIC ET 200SP, Digital output module, DQ 16x 24V DC/0,5A

Standard, Source output (PNP,P-switching) Packing unit: 1 piece, fits
to BU-type A0, Colour Code CC00, substitute value output, module
diagnostics for: short-circuit to L+ and ground, wire break, supply
voltage

General information
Product type designation DQ 16x24VDC/0.5A ST
Firmware version V0.0
● FW update possible No
usable BaseUnits BU type A0
Color code for module-specific color identification CC00
plate
Product function
● I&M data Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated as of V14
version
● STEP 7 configurable/integrated as of version V5.5 SP3
● PCS 7 configurable/integrated as of version V8.1 SP1
● PROFIBUS as of GSD version/GSD revision One GSD file each, Revision 3 and 5 and higher
● PROFINET as of GSD version/GSD revision GSDML V2.3
Operating mode
● DQ Yes
● DQ with energy-saving function No

6ES7132-6BH01-0BA0 Subject to change without notice

Page 1/4 11/07/2018 © Copyright Siemens
 ● PWM No
● Oversampling No
● MSO No
Redundancy
● Redundancy capability Yes

Supply voltage
Rated value (DC) 24 V
permissible range, lower limit (DC) 19.2 V
permissible range, upper limit (DC) 28.8 V
Reverse polarity protection Yes

Input current
Current consumption, max. 60 mA; without load

Output voltage
Rated value (DC) 24 V

Power loss
Power loss, typ. 1W

Address area
Address space per module
● Address space per module, max. 2 byte; + 2 bytes for QI information

Hardware configuration
Automatic encoding Yes
● Mechanical coding element Yes
Selection of BaseUnit for connection variants
● 1-wire connection BU type A0
● 2-wire connection BU type A0 + Potential isolation module
● 3-wire connection BU type A0 + Potential isolation module
● 4-wire connection BU type A0 + Potential isolation module

Digital outputs
Type of digital output Source output (PNP, current-sourcing)
Number of digital outputs 16
Current-sinking No
Current-sourcing Yes
Short-circuit protection Yes
● Response threshold, typ. 1A
Open-circuit detection Yes
Limitation of inductive shutdown voltage to Typ. L+ (-50 V)
Controlling a digital input Yes
Switching capacity of the outputs
● with resistive load, max. 0.5 A
● on lamp load, max. 5W

6ES7132-6BH01-0BA0 Subject to change without notice

Page 2/4 11/07/2018 © Copyright Siemens
 Load resistance range
● lower limit 48 Ω
● upper limit 12 kΩ
Output current
● for signal "1" rated value 0.5 A
● for signal "0" residual current, max. 0.1 mA
Output delay with resistive load
● "0" to "1", typ. 50 µs
● "1" to "0", typ. 100 µs
Parallel switching of two outputs
● for uprating No
● for redundant control of a load Yes
Switching frequency
● with resistive load, max. 100 Hz
● with inductive load, max. 2 Hz
● on lamp load, max. 10 Hz
Total current of the outputs
● Current per channel, max. 0.5 A
● Current per module, max. 8A
Total current of the outputs (per module)
horizontal installation
— up to 30 °C, max. 8A
— up to 40 °C, max. 8A
— up to 50 °C, max. 6A
— up to 60 °C, max. 4A
vertical installation
— up to 30 °C, max. 8 A; in all other mounting positions
— up to 40 °C, max. 6 A; in all other mounting positions
— up to 50 °C, max. 4 A; in all other mounting positions
Cable length
● shielded, max. 1 000 m
● unshielded, max. 600 m

Isochronous mode
Isochronous operation (application synchronized up No
to terminal)

Interrupts/diagnostics/status information
Diagnostics function Yes
Substitute values connectable Yes
Alarms
● Diagnostic alarm Yes
Diagnostic messages

6ES7132-6BH01-0BA0 Subject to change without notice

Page 3/4 11/07/2018 © Copyright Siemens
 ● Monitoring the supply voltage Yes
● Wire-break Yes; Module-wise
● Short-circuit to M Yes; Module-wise
● Short-circuit to L+ Yes; Module-wise
● Group error Yes
Diagnostics indication LED
● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED
● Channel status display Yes; Green LED
● for channel diagnostics No
● for module diagnostics Yes; green/red DIAG LED

Potential separation
Potential separation channels
● between the channels No
● between the channels and backplane bus Yes

Isolation
Isolation tested with 707 V DC (type test)

Standards, approvals, certificates

Suitable for safety-related tripping of standard Yes; From FS01
modules

Ambient conditions
Ambient temperature during operation
● horizontal installation, min. 0 °C
● horizontal installation, max. 60 °C
● vertical installation, min. 0 °C; in all other mounting positions
● vertical installation, max. 50 °C; in all other mounting positions
Altitude during operation relating to sea level
● Ambient air temperature-barometric pressure- On request: Ambient temperatures lower than 0 °C (without
altitude condensation) and/or installation altitudes greater than 2 000 m

Dimensions
Width 15 mm
Height 73 mm
Depth 58 mm

Weights
Weight, approx. 30 g

last modified: 11/05/2018

6ES7132-6BH01-0BA0 Subject to change without notice

Page 4/4 11/07/2018 © Copyright Siemens