VAITEC HVR User Manual
1 Turn on
1.1 Turn on
Plug the power supply, power supply indicator light will be on and you will hear “DI” sound,
the DVR will turn on after self-test.
Note: pls use the enclosed power supply, in case DVR can’t work normally or broke. For the
power with switch, pls make sure it’s close.
1.2 Shutdown
There are two methods to turn off the DVR. One is soft closedown: Right click to pop-up
menu bar, Click the button marked by the red arrow in the following picture to shutdown
the system; the other is hardware power off: plug off the power supply to shut down the
device.
Note: Recovered after power off, If the device is shut off in improper way when it’s in the
working condition, after reboot, the record information before shut off will be saved and it
will be back to the status before shutoff. Before you change the HDD, pls power off first.
2. Setup wizard
When the DVR boots up, the setup wizard will pop-up, for the first time, the user can follow the
prompt message to configure.
3. Admin password setting:
After the device power on, pls set your password before operation and configuration, system will
follow the corresponding commands according to the user authorization, there’re 2 users as
default, one is admin, and the other is guest. Password is Null for admin.
For your system security, please modify your password after first login, and in the future it won’t
have this prompt message again. After you set the password, pls enter the password to login
Click” Next” to enter P2P cloud service by scan the following QR.
Android, IOS: scan QR to download app.
SN: Find the Device ID
After that, click “Next”, enter into the interface for configuring network.
【DHCP Enable】 Obtain IP address automatically.
【IP Address】 Default: 192.168.1.10
【Subnet Mask】 Default: 255.255.255.0
【Gateway】 Default: 192.168.1.1
If you want to make DVR connect with network, pls make the device’s IP address is in the same
network segment with the router and it should conform to router’s IP rules. It can’t conflict with
other devices IP in the LAN. Or you can also chose “DHCP Enable” to get an IP address
automatically (router should have DHCP service). Click “Save” to finish the whole wizard
configuration.
4. Channel mode
The chancel modes supported by the device can be viewed and configured via 【main menu】>
【system configuration】>【channel management】, there’re several modes: Local (AHD/TVI/CVI):
the number under the resolution is the channel numbers. You can choose the channel number
according to your requirement. The right side is for IP (for example: 4+4= 4 channel analog
channels (AHD/TVI/CVI/CVBS) + 4 channel IP).
Note: High resolution modes can be compatible with lower resolution cameras; lower resolutions
can’t be compatible with higher solutions cameras. For examples: analog channel 4*1080P can
connect with 1080P cameras and also 720P cameras.
5. Coaxial control
Function: set AHD camera’s configuration
Choose the channel with coaxial camera, and then right click main menu to choose to get
coaxial control menu.
Click to enter into camera configuration interface. Use or to switch
between the camera menu. Use or choose the specific parameters, and after
switch to “exit”, click to exit.
Coaxial control menu including: AF Zoom + -； Focus + - ；Iris+ -；UTC control etc..
6. Encode
Go to【main menu】>【Record】>【setup】，Go to encode configuration interface
Main stream is used for local record, playback. Sub-stream is used for remote surveillance, such
as: mobile surveillance. Dual stream technology can make playback and remote surveillance
more smooth and clear.
Note： Different products have different encode resolution options. Both video and audio icon
displayed means record files including video and audio.
7. Record
7.1 hard disk setting
Format when first log in By [main menu]>[ HDD Manage]>[setup]. After formatting, pls set
the hard disk as read-write hard disk via 【read-write hard disk setting】
There is at least one read-write hard disk.
7.2 Record settings
Click [main menu]>[Record]>[Schedule] to set recording
[Channel] Choose the corresponding channel number to set the channel. Choose the all option to
set the entire channels.
[Record Mode] Click when preview to set video status, there’re 3 status: Schedule,
manual or stop.
Schedule: Record according to video type or time section.
Manual: After changing to manual, the corresponding channel will be recorded the whole day 24
hours.
Stop: The corresponding channel will stop recording.
After you choose the configuration mode, you can set the recording type and time section.
[Time section] The recording will start only in the set time range.
[Recording type] set recording type, there’re 4 types: No record , Regular , detection ，
Alarm
Regular: Regular recording is arranged in the setting time section. The video file type is “ ”.
Detect: Trigger the “motion detect”, “video mask”or “video loss” signal, when above alarm
is set as opening recording, the “detection recording” state is on. The video file type is “ ”
Alarm: Trigger the external alarm signal in the set time section, and the alarm is set as opening
recording, the video file type is “ ”.
7.3 Record query and playback
Play the record video in the hard disk: right click menu to get “record playback”, choose
to playback.
Quick playback: Quick play the record in the corresponding time section
Browse playback: browse the corresponding record
Playback by time: It will show the earliest time and the latest time in the hard disk. You can
playback quickly.
Playback by event: browse quickly, choose alarm/motion detection playback
Playback by time bar: Choose the date, and check the corresponding record in the time section.
Multi-channel playback is supported.
Smart playback: choose the date, and skip the video you don’t follow.
Record backup: Choose the storage location, Click to cut to finish cut. Click to
backup. Click detection (read-write or device backup) to choose recording time and channel.
Under the channel, you can check the cut video file’s size. Click start to check the time column.
There will be tick after finishing backup.
Record playback: Double click the files in the list to playback, or playback by time in the time
column.
Playback all channel: Before playback, pls choose all channel and then playback all the channels.
Zoom: Click playing video, drag mouse left to chosen the area, and then move mouse into the
zoom +/- area, right click to exit zoom.
8. Alarm
Take motion detection as example
8.1 Alarm setting (main menu-channel configuration-motion detection)
The functions include: open/close, sensitivity, detection area, defense time, trigger mode.
8.2 Motion detection Linkage setting
Include: (screen prompt, buzzer, trigger channel recording (need to set), snapshoot, alarm
output, trigger PTZ, and some Motion detection Linkage setup need combine with other
function (such as linkage videos recording, send Email), that is how to deal with when it is
generate an alarm. You can copy all the channel setting by chose (Copy) in the right button,
and then save & exit-ok to exit.
9. LAN access
After network is connected, you can login IE browser for remote monitor.
10.1 Open IE browser, enter device IP in address bar. For example: defaut IP is 192.168.1.10,then
enter http://192.168.1.10 into the address bar to connect.
10.2 Enter user name and password, default user name is admin, no password. For safe reason,
please modify the password. After log in successfully, it will pop up the monitoring interface as
below.
Note: when first log in, you need install ActiveX, IE default stop the ActiveX， so please go to
<internet option>--<safe>--<custom level>--<ActiveX>, and enable all ActiveX.
10.Public network access
Cloud technology makes access device in public network easily and conveniently.
10.1 Access by PC
Open IE browser, enter into http://easyweb.zwcloud.wang/login.html to log in Cloud service
network website.
There’re 2 login methods: login by user (App registered user) and login by device’s UID. User
can manage multiple devices simultaneously if you login by users. If you login by device’s UID,
you can only access one device.
10.2 EasyVMS, you can install EasyVMS on PC, use login account to use cloud service.
There’re 2 login methods: login by user (App registered user) and login by device’s UID. User
can manage multiple devices simultaneously if you login by users. If you login by device’s UID,
you can only access one device.
10.3 Access by mobile
Network environment：WIFI, 3G, 4G
Terminal system ：Android, IOS
APP：P2PViewCam / P6SPro
Downloading place：Google play, APP Store.
10.4 Download app locally (easiest way),
Enter main menu-system –network-P2P on the top right corner.
Scan to download App, after that, login by the account, and click “+” on top right corner and scan
UID to get the preview.
