© : Ergonomics of laparoscopic surgery by: Dr/ Adel Fathi lecturer of surgical oncology - OCMU - Egypt (Oncology Center Mansoura University) www.laparoscopicclinic.com www.adelfathi.comMany forces exerted can be measured easily » Too little force is ineffective » Too much force causes damage & inaccuracy » You manage what you measure » You cannot fix what you do not know about www. laparoscopicclinic.com www.adelfathi.comTHE HAWTHORNE EFFECT » Commonly referred to as the observer effect » It has been a well-observed phenomenon that any individual performs a skill better and with more caution whenever he has the knowledge that he is under observation and assessment. This allow the results to be more positive » This constitutes the "Hawthorne effect" which has been found applicable to most scientific assessments of human function and hence an integral knowledge of this aspect is essential for ergonomic purposes. www.laparoscopicclinic.com www.adelfathi.com<7 ivmpopuenon ae » In 1901, when Kelling introduced a visualising scope for the first time in the peritoneum of a dog, it was a landmark in the history of surgery. However, it took another eight decades for a perfected laparoscopic technique to be implemented, when for the first time, » Mouret performed a successful laparoscopic cholecystectomy in 1987. www.laparoscopicclinic.com www.adelfathi.com_Bavmpopuerigy at «In the wake of all advances, come the drawbacks. xLaparoscopy is no exception. The drawbacks are majorly twofold www.laparoscopicclinic.com www.adelfathi.comxin the first scenario, the surgeon experiences the ill effects from the surgery, and secondly, the patient is the victim. www.laparoscopicclinic.com www.adelfathi.com4 ivmpopuenion, ae «There have been multiple reports of carpal tunnel syndrome, eye strain and cervical spondylosis among unsuspecting surgeons performing multiple laparoscopic procedures in high-volume centers. www.laparoscopicclinic.com www.adelfathi.com4" RInmRopUCTION, = xlIn the first decade after the advent of laparoscopy, patients too have been found to be experiencing a lot of inconvenience with greater post-operative pain at port sites and due to other complications of the procedure in some cases. The mistakes leading to these poor outcomes seem to be _ completely avoidable with use of simple application of understanding of the physics and functioning of the whole event. www.laparoscopicclinic.com www.adelfathi.com<7 impopuenon a «Now, we will understand the principle of Ergonomics applicable to the field of laparoscopy as much as any other surgical expertise. www.laparoscopicclinic.com www.adelfathi.comron | or WHAT IS ERGONOMICS ? » The term ergonomics is derived from the Greek words "ergon" meaning work and "nomos" meaning natural laws or arrangement. » Ergonomics is "the scientific study of people at work, in terms of equipment design, workplace layout, the working environment, — safety, productivity, and training". » Ergonomics is based on anatomy, physiology, psychology, and engineering, combined in a systems approach. www.laparoscopicclinic.com www.adelfathi.comGon we WHAT IS ERGONOMICS x In simple words, it is the science to make the setting and surroundings favorable for the laparoscopic surgeon. » The term was formally defined in 1949 and has brought benefit and safety to many areas of human endeavor. www.laparoscopicclinic.com www.adelfathi.comGn a ae WHAT IS ERGONOMICS » The importance of ergonomics in the setting of laparoscopy have shown’ that correct ergonomics can reduce suturing time. » Pressure-related chronic pain among surgeons has been shown to be relieved by the use of ergonomically designed products. www.laparoscopicclinic.com www.adelfathi.comron er scar WHAT IS ERGONOMICS x Hence, it is imperative to understand the applications of ergonomics for all surgeons practicing laparoscopy. «The aim now is to provide a_ basic understanding of the ergonomic challenges facing the laparoscopic surgeon and some simple modifications, which can go a long way in improving their operative practice. www.laparoscopicclinic.com www.adelfathi.comERGONOMIC CHALLENGES DURING LAPAROSCOPY: _ » Differences between open and laparoscopic surgery are the following. Open surgery has a high degree of freedom and surgeons work in line with visual axis. There is a_ three- dimensional direct vision and direct tactile feedback. www.laparoscopicclinic.com www.adelfathi.comLIMITATIONS DURING LAPAROSCOPIC SURGERY: RS ~ Two-dimensional vision « Loss of depth perception to some extent. ~ There is fulcrum effect with tremor enhancement. ~ There are only 4 degrees of freedom. ~ The major limitation is that view is not under control of the surgeon. Decoupling of the visual and motor axes » The loss of tactile sensation which replaced by instruments » Limited viewing spectrum offered ~ Static posture during major part of the procedure which contributes to the inefficiency ~ Separation of the axis of vision and the axis of the physical aspect of the procedure www.laparoscopicclinic.com www.adelfathi.com» The quality and resolution details of the image are not comparable with direct visualisation. «The newer generation 3D visual cameras significantly improved the laparoscopic precision of beginners and _ experienced surgeons. www. laparoscopicclinic.com www.adelfathi.com» The surgeon does not get a chance to directly look at the instruments or his hands and also at the field of surgery at the same time. He has to learn to adapt to the difficulty of combining the two functions into the same-channelled approach in order to manipulate the tissues without direct contact. »« Studies have shown that working in separate coordinate systems decreases _ performance, leading to higher rates of error in the procedure. www.laparoscopicclinic.com www.adelfathi.com» Great concentration and skill is required for performing the complex laparoscopic surgeries. » It has been observed that the operating surgeon assumes a more static posture’ during laparoscopic procedures compared to open approach. These static postures have been demonstrated to be more disabling and harmful than dynamic postures are since muscles and tendons build up lactic acid and toxins when held for prolonged periods in same postures. www.laparoscopicclinic.com www.adelfathi.com» Sensorial ergonomics (manipulations and visualisation) improve precision, dexterity, and confidence, while physical ergonomics provide comfort for surgeon. Together, these two elements of ergonomics increased safety, have better outcome and reduce the stress. www.laparoscopicclinic.com www.adelfathi.comERGONOMICS CONCEPTS IN OT www.laparoscopicclinic.com www.adelfathi.comoy JON- AMERICAN QR EUROPEAN CL» OT east - AMERICAN OR EUROPEAN » A surgeon in two different positions can perform laparoscopic cholecystectomy. One is by standing on the left side of patients (preferred by Americans) and other is by standing between the legs (preferred by Europeans). Both the positions are convenient but some find one more ergonomically better. x» It is usually surgeon's preference or habit of getting adjusted to the position. Though port placement is similar, there is slight change in each position. www.laparoscopicclinic.com www.adelfathi.com( Portaate ae » Height of operating table should be adjusted between 64 and 77 cm above floor level since this discomfort and operative difficulty are lowest when instruments are positioned at elbow height. (0.49 X height of the surgeon in cm) www.laparoscopicclinic.com www.adelfathi.com» Ergonomically, the best view for laparoscopy is with the monitor image at or within 25 optimal degrees below the horizontal plane of the eye. This leads to least neck strain according to the available studies. » Standard LCD monitors placed on a low cart separate from the operating room equipment may be used for best results. It is not advisable to have a "“chin-up" arrangement on the part of the surgeon. x» Monitor placed at a certain distance of 4-8 feet (1.2-2.4 m) away from the surgeon's eye « In operations where surgeons change their ports and positions, the e.g. total colectomy. Second monitor for assistants reduces strain on their neck. www. laparoscopicclinic.com www.adelfathi.comwww.laparoscopicclinic.com www.adelfathi.comCAMERA MAGNIFICATION. » Problems related to depth perception, vision and loss of peripheral visual fields can be reduced by using a 10-15X magnification on the optical system offered by the recording camera and the output to the display. This can make life easier while operating, especially when dealing with minute internal anatomy. www.laparoscopicclinic.com www.adelfathi.comTROCAR PLACEMENTS » There is no uniform consensus about port placements for advanced laparoscopic procedures. The placement of ports is currently dictated by the surgeons' preference based _on individual experience. «To facilitate smooth instrument manipulation along with adequate visualisation during laparoscopy, usually trocars are placed in triangular fashion. This is termed as triangulation (Baseball Diamond Court Concept) . Bi ll Diamon » If this principle is followed the clashing between the instruments can be prevented www.laparoscopicclinic.com www.adelfathi.comRetracting port ~ . Operating of port Umbilicus (Viewing port) www.laparoscopicclinic.com www.adelfathi.com» The target organ should be 15-20 cm from the centre port used for placing the optical trocar. Generally, the two remaining trocars are placed in the same 15-20 cm arc at 5-7 cm on either side of the optical trocars. » This allows the instruments to work at a 60° angle with the target tissue and avoids problems of long handle due to too far or too near placement of ports and the problem of abdominal wall interference. » If necessary, two more retracting ports can be placed in the same arc but more laterally so that instruments do not clash. www.laparoscopicclinic.com www.adelfathi.com» When optical trocar is placed as one of the lateral port trocar, it is called as sectorisation. This is usually done during appendicectomy when 10 mm trocar is placed in subumbilical region as optical trocar. Two other trocars are placed below these trocars laterally. » Sectoring of instruments should be avoided by beginners since it requires a greater degree of understanding and experience of the laparoscopic view and significantly different hand-eye coordination. www.laparoscopicclinic.com www.adelfathi.comUmbilicus (viewing port) Target organ — Operating port Operating port www.laparoscopicclinic.com www.adelfathi.comcage » Another factor that one should consider during trocar placement is that the instrument length is limited. \f trocar is too far from the desired position, then one has to push abdominal wall towards target organ to gain a few centimeters. This not only makes these movements less precise but also causes strain on the fingers and hand muscles. www.laparoscopicclinic.com www.adelfathi.comMANIPULATION ANGLES FOR INSTRUMENTATION www.laparoscopicclinic.com www.adelfathi.com» Manipulation Angie is the angle between two working ports. Ideal manipulation angle is 60°. » Azimuth Angle is the angle between one instrument and the optical axis of the endoscope. Ideal azimuth angle is equal for the active and assisting instruments. » Elevation Angle is the angle between the instrument and the horizontal plane. Ideal elevation angle is 60°. These three angles determine the optimal port placement. www.laparoscopicclinic.com www.adelfathi.compeal ne Veena plane Azimuth Angle Manipulation Angle Elevation Angle www.laparoscopicclinic.com www.adelfathi.com» Manipulation angle ranging from 45° to 75° with equal azimuth angles is recommended. » The 90 manipulation angle had the greatest muscle workload by the deltoid and trapezius of the extracorporeal and intracorporeal limbs and the extracorporeal dominant arm extensor and flexor groups. » Task efficiency was reported be better with equal azimuth angles than with unequal azimuth angles. Achieving equal azimuth angles may be difficult in many practical situations, but in principle, azimuth inequality should be avoided because it degrades task efficiency. www. laparoscopicclinic.com www.adelfathi.com30 degree manipulation angle www. laparoscopicclinic.com www.adelfathi.com60 degree manipulation angle www. laparoscopicclinic.com www.adelfathi.com90 degree manipulation angle www.laparoscopicclinic.com www.adelfathi.com120 degree manipulation angle www. laparoscopicclinic.com www.adelfathi.com» There exists a direct correlation between the manipulation and the elevation angles. With a manipulation angle of 60°, the corresponding optimal elevation angle which yields the optimal quality performance is 60°. » Wide manipulation angles necessitate wide elevation angles for optimal performance and task efficiency. When a 30° manipulation angle is imposed by the anatomy or build of the patient, the elevation angle should be also 30° as this combination carries the shortest execution time. www.laparoscopicclinic.com www.adelfathi.com» The best ergonomic layout for endoscopic surgery consists of a manipulation angle ranging from 45° to 75° with equal azimuth angles and elevation angles equal to manipulation angle www.laparoscopicclinic.com www.adelfathi.comPOSITION OF THE ARM www.laparoscopicclinic.com www.adelfathi.comx The suggested position of arm is slightly abduction, retroversion and rotation inwards at shoulder level. The elbow should be bent at about 90°-120°. x The surgeon has to remember that moving about and _ loosening up his hands intermittently is essential to prevent the buildup of lactic acid and ward off fatigue. www.laparoscopicclinic.com www.adelfathi.comEQUIPMENT RELATED CHALLENGES www.laparoscopicclinic.com www.adelfathi.com» US Food and Drug Administration reporting that probably half of the 1.3 million instrument- related injuries that occur in US hospitals each year could be due to poor instrument design www. laparoscopicclinic.com www.adelfathi.com» The surgeon cannot move his instruments with unlimited degree of freedom. The laparoscopic instruments, which are most commonly in use in our setting at present, offer only 4 degrees of freedom of movement, which are rotation, up/down angulations, left/right angulations, in/out movement. » Wright and Falk, et al. have suggested that an increase in degree of freedom from 4 to 6 increases dexterity by a factor of 1.5 www.laparoscopicclinic.com www.adelfathi.com» Laparoscopic instruments work on _ reduced efficiency. For example, the laparoscopic grasper transmits force with a ratio of only 3:1 from the handle to the tip as compared to 1:3 with the hand-held hemostat. Hence, a laparoscopist has to work six times harder for similar results. » Moreover, these laparoscopic instruments are generally available in one standard size and hence surgeons of all heights, builds, and hand sizes work with same ones and the efficacy suffers somewhere along the way. www.laparoscopicclinic.com www.adelfathi.com| » 3mm instrument... 20 cm - 25cm - 30 cm » 5 mm instrument ....... 30 cm - 36cm - 43 cm » 10 mm instrument ....... 36 cm - 43cm www. laparoscopicclinic.com www.adelfathi.comon een ue ag MATTERN WALLER HANDLES _ » Mattern and Waller have stated that improperly designed shapes of instruments cause strain on functional areas of the hand. They have designed handle that is based on ergonomic criteria. This multifunctional handle is shaped to fit only one hand and like a pistol handle, it rests continuously in the half- closed hand, similar to the "basic position" of the resting hand, between the ring and little fingers, with the thenar performing an encircling grip. The longitudinal axis of the instrument is an extension of the forearm's rotation axis. This allows pronation and supination to be transferred directly to the instrument effector. www.laparoscopicclinic.com www.adelfathi.comPHYSICAL CONSTRAINTS TQ SURGEON RUE TQ INEFFICIENT APPLICATION OF ERGONOMICS www.laparoscopicclinic.com www.adelfathi.com» Neck pain and spondylosis has been observed to be a recurring complaint among surgeons in high-volume centers in the first decade after the advent of minimal access surgery. The same height, at which the video monitor used to be set for surgeons of different heights, was found to be the underlying cause. www.laparoscopicclinic.com www.adelfathi.com» The other physical constraints reported are cervical spondylitis, shoulder pain due to abduction of shoulder (chicken wing scapula) during laparoscopy termed as "laparoscopic shoulder", backache, hand finger joint pain, tenosynovitis, burning eyes, stress exhaustion, and hand muscle injury www.laparoscopicclinic.com www.adelfathi.com» Most common reason for the inability of ergonomics to be applied optimally in the field of laparoscopy could be enumerated as: aCommunication gap between the practitioners of laparoscopy and the designers of the instruments, © The lack of complete awareness among surgeons, “1 Inadequate knowledge of the potential problems for the users in the instruments created by the designers and the contradictory expert advice which reduces the credibility of ergonomics as a science. www. laparoscopicclinic.com www.adelfathi.comEND » Laparoscopic surgery provides patients with less painful surgery but is more demanding for the surgeon. » The increased technological complexity and sometimes poorly adapted equipment have led to increased complaints of surgeon fatigue and discomfort during laparoscopic surgery. » Better ergonomic integration and understanding ergonomics can not only make the life of surgeon comfortable in the operating room but also reduce physical strains on the surgeon. www.laparoscopicclinic.com www.adelfathi.comhank you www.laparoscopicclinic.com www.adelfathi.com