Service Bulletin
Surgical Products Ophtalmology Service-Bulletin Version
No. 532 No. 2.0
Aktion / Action Status Kostenerstattung / Cost Recovery Gültigkeit / Validity
Sofort Hersteller Bis :
Immediate Manufacturer Until (date):
Nächster Besuch VG oder Vertretung Nach:
First Opportunity Agent / Dealer After (date):
Bei Reparatur Kunde Bis Serien-Nr.:
In the event of repair Customer To (ser. No.):
Kundenwunsch Servicekodierung Ab Serien-Nr.:
At customer request Service Coding From (ser. No.):
Zur Information IC Bis auf Widerruf
For Information Only Until further notice
FC Ersetzt Service Bulletin Nr.: 532 V1.0
This bulletin replaces no.: 532 V1.0
Re: IOLMaster
New Camera module available
Table of contents
1. General Information 2
2. Necessary tools / continuative documentation 2
3. Identification / Differentiation 3
4. Adjusting the sensitivity 4
Version 2.0
Service-Bulletin No. 532 IOLMaster 1/5
1. General Information
Due to a focus level shift of the CCD-chip of some CCD-cameras (mostly on the
1493-442 types), this camera has been modified to a camera exchange kit with
different bases. The kit also contains shim rings to cover all know focus-levels of the
previous generations.
See Bulletin 560 for further information.
The kit is fully backward compatible for all IOLMaster generations, containing Digital-
IOL PCBs with camera operating voltage of 9V. It is not compatible if Digital-IOL PCBs
with a camera operating voltage of 8V are used. In this case the related Digital-IOL
PCB must also be exchanged.
See Bulletin 448 for further information.
Note!
The new camera-module needs a different adjustment
voltage – see chapter 4 at page 4 (Adjusting the sensitivity).
2. Necessary tools / continuative documentation
Tools:
─ standard tools
─ calibrated multimeter
─ IOLMaster calculation-spreadsheet
Continuative documentation:
─ IOLMaster service manual (SM-30-4039)
─ IOLMaster service manual (SM-30-4047)
─ Bulletin 560
─ Bulletin 510
─ Bulletin 448
─ Bulletin 305
─ Bulletin 292
Version 2.0
Service-Bulletin No. 532 IOLMaster 2/5
3. Identification / Differentiation
OLD / 8V replaced
Image with „Blooming“ - line
CCD sensitivity voltage = 3.4 V ± 0.5 V
1022-328
focused image in ALM – mode
OLD / 9V replaced
Image with „Blooming“ - line
focused image in ALM – mode
OLD / 9V replaced
Image with NO „Blooming“ - line
CCD sensitivity voltage = 2.9 V ± 0.3 V
focused image in ALM – mode
NEW / 9V (complete kit)
Image with NO „Blooming“ - line
White bases
1677-370
focused image in ALM – mode
Part-No. Description Status Remark
1022-328 CCD camera, complete (old version / 8V) Replaced Unavailable
1308-774 CCD camera, new complete Replaced No longer available
1493-442 CCD camera, 9V / Version 02, complete Replaced No longer available
1677-370 Kit, CCD camera 9V/V03 (white bases) New Available
1297-413 CCD cable 2 Valid Included with camera
Version 2.0
Service-Bulletin No. 532 IOLMaster 3/5
4. Adjusting the sensitivity
Adjust the R75 potentiometer at the Digital-IOL PCB in such a way, that a voltage of
NEW: 2.9V ± 0.3V (OLD: +3.4V ± 0.5V) is present between the GND and the potentiometer
slider contact (middle contact). Use a calibrated multimeter.
2.9 V
Caution!
The operating voltage (8V / 9V) is not adjustable and depends upon
the hardware-version of the Digital-IOL PCB.
The new type of CCD camera module is only compatible with the
9V version of the Digital-IOL PCB. You cannot use the new camera-
module with an 8V version of the Digital-IOL PCB, even if it the
image looks good. In this case the camera is not within
specification, and this may lead to incorrect readings of the image
analysing software, which could influence the KER, ACD and WTW
results.
Note!
See Bulletin 448 regarding further information of 8V / 9V
determination of Digital-IOL PCB.
See Bulletins 292 and 305 regarding further information about
determination version 1 (1031-843) and version 2 (1078-792)
Digital-IOL PCB.
Caution!
After replacement of the camera module it will be necessary to
perform the adjustment of the surrounding field illumination (R86)
and the Keratometer-illumination (R87) potentiometers on the
Digital I/O PCB.
If the IOLMaster is equipped with Software 5.02 or higher, also the
spot-size calibration (50….55) of the Keratometer-spots must be
readjusted.
See Bulletin 510 for the related procedure.
Also a re-calibration of the KER, ACD and WTW might be
necessary if the measurement results (of the test-eye) are not
within the imprinted tolerances.
See service-manual for the related procedures and further
information.
Version 2.0
Service-Bulletin No. 532 IOLMaster 4/5
78M08 Æ +8 V Å version Æ +9 V Å 78M09G
R28 – Laser adj. power (40µW)
R30 – Laser 100% power (400 µW)
Surr. Field illumination – R86
Keratometer illumination – R87
8V 9V
1031-843 Æ Version 1
1078-792 Æ Version 2
The imprinted number on the board itself is NOT
conclusive to determine between version 1 and 2.
Some boards may have the version 1 number
imprinted but are configured as version 2.
Take the number from the sticker as the reference
for either version 1 or 2 identification.
Note!
Please contact us at czm.service@meditec.zeiss.com for any questions
you may have regarding this Bulletin or the procedures described within.
MAG-SF / Wistuba
2008-10-27
Version 2.0
Service-Bulletin No. 532 IOLMaster 5/5
