All manuals and user guides at all-guides.

com

SP200 Series
A, B type

HOME-USE SEWING MACHINE

INSTRUCTION

m
MANUAL
instructions. .co
•• Read this manual carefully before use and always follow the

•• Keep the manual in a convenient place for easy reference.

es
•• If you give the sewing machine to someone else, also give
them this instruction manual.
uid
-g
all
 All manuals and user guides at all-guides.com

Contents
1 Before use (Be sure to read this section before use)
•• Important safety instructions. ............................................ 3
•• How to change the power plug.......................................... 5
•• Part names........................................................................ 6
•• Part names and their functions.......................................... 8
•• Quick adviser................................................................... 10
•• How to operate foot controller......................................... 11

2 Sewing preparations
•• Connecting the power. .................................................... 12
•• Installation of battery for winding the lower thread.......... 13
•• Winding the lower thread................................................. 14
•• Threading the lower thread. ............................................ 16
•• Threading the upper thread............................................. 18
•• Using the needle threader............................................... 20
•• Pulling up the lower thread.............................................. 22
•• Application of each stitch pattern. ................................... 23
•• Changing the presser foot............................................... 26
•• Changing the needle....................................................... 28
•• Relationship between the needle, thread and fabric, and
adjusting the thread tension............................................ 29

3 Sewing
•• Straight stitching and reverse sewing.............................. 30
•• Zigzag sewing. ................................................................ 34
•• Adjusting thread tension.................................................. 35
•• Buttonhole sewing........................................................... 36
•• Overcasting..................................................................... 39
•• Zipper insertion................................................................ 40
•• Blind hem stitching.......................................................... 42

4 Maintenance
•• Feed dog and hook maintenance.................................... 44
•• Changing light bulb.......................................................... 48
•• Servicing double-insulated products (230V-240V).......... 49
•• Notice about the incandescent lamp............................... 49
•• Safety precaution about the battery. ............................... 49
•• Troubleshooting............................................................... 50

5 Others
•• Recycling......................................................................... 53
•• Specifications.................................................................. 54

2
 All manuals and user guides at all-guides.com

1 Before use (Be sure to read this section before use)

Important safety instructions
1
These safety instructions are designed to prevent danger or damage arising from the

Before use (Be sure to read this section before use)

incorrect operation of the machine. Read carefully and always follow the instructions.

Explanation of “ Warning” and “ Caution”

An incorrect operation could result in death or serious injury.

Warning
An incorrect operation could result in an injury or damage to
Caution the machine.

Symbol explanation

Do not touch. Prohibited actions

Remove the power plug from

Required actions the outlet.

Warning

Use an AC 220 to 240 V power source.

Not doing so could cause an electric shock or a fire.

Do not damage the power cord, modify it, bend it excessively, jerk it or
twist it.
Doing so could cause an electric shock or a fire.
If the power cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or its service agent.

Do not use outdoors.

Doing so could cause an electric shock or a fire.

Do not operate where aerosol (spray) products are being used or where
oxygen is being administered.
Doing so could cause a fire.

Do not repair, disassemble or modify except what is mentioned in the

instruction manual.
Doing so could cause an electric shock, a fire or an injury.

3
 All manuals and user guides at all-guides.com

Caution

Be sure to close the bobbin case cover before operating the sewing machine.
Not doing so could cause an injury.

When the machine is not in use it should be stored safely, not on the floor
as protruding parts could cause injury if a person fell on the machine.
Not doing so could cause an injury.
Before changing the needle or threading the lower thread or upper thread,
use the main power switch to turn off the sewing machine.
Not doing so could cause an injury.

Do not look away from the needle while operating the sewing machine.
If the needle breaks it could cause an injury.

Do not touch moving parts such as the needle, take-up lever or handwheel.
Doing so could cause an injury.

Do not place your hand or fingers under the needle.

Doing so could cause an injury.

Do not use when young children are near the machine.

Children shall not play with the machine as they could touch the needle and be
injured.

When leaving the sewing machine after using it, use the main power switch
to turn off the sewing machine, and then remove the power plug from the
outlet.
Not doing so could cause an injury.

Before using the sewing machine make sure that the presser foot holder
clamp screw, needle clamp screw and needle plate screw are firmly tightened,
and that the presser foot is properly set in the presser foot holder.
Not doing so could cause an injury.

Do not perform the following actions.

Doing so could cause an injury.
•• Sewing without lowering the presser foot.
•• Sewing while the needle is incorrectly installed.
•• Using a bent needle.
•• Sewing while jerking the fabric.
•• Moving the pattern selection dial while sewing.

4
 All manuals and user guides at all-guides.com

Caution

Do not operate on an unstable surface such as a sofa or a bed.

If the sewing machine falls down, it could cause an injury or damages to the machine.
1
Do not drop or insert any foreign objects into any openings such as

Before use (Be sure to read this section before use)

opening space when you remove the face cover and / or the outer casing
space of bobbin case.
Doing so could cause an injury or damages to the machine.

The machine can be used by, children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge,
only if they are supervised or have been given proper instructions concerning use of the
machine in a safe way and fully understand the hazards involved.

UK ONLY IMPORTANT PLEASE READ CAREFULLY

How to change the power plug

Warning

When you change the power plug or cord, do not repair, disassemble or
modify except at the authorised dealer or service centre.
Doing so could cause an electric shock or a fire

If for any reason the power plug for this product is removed it should be
immediately disposed of safety and not stored anywhere where it could be
inadvertently used again.
Doing so could cause an electric shock or a fire

The wires in this mains lead are coloured in accordance with the following code:
BLUE-NEUTRAL BROWN-LIVE ( OR ACTIVE )
As the colours of the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug - PROCEED AS FOLLOWS:
The earth plug pin is unnecessary. As the machine is designed under double insulation
structure, the earth wire is removed from the machine. The wire coloured BROWN must
be connected to the terminal marked L or A or coloured RED. The wire coloured BLUE
must be connected to the terminal marked N or coloured BLACK. Neither core is to be
connected to the earth terminal of a three-pin plug.

5
 All manuals and user guides at all-guides.com

Part names

Upper thread tension dial

Thread guide
Spool pin
Presser foot pressure
adjustment knob Quick adviser

m
** Equipped only with
model XXX34 Stitch length dial

Take-up lever

.co
Pattern selection dial
Light bulb

Face cover Reverse sewing lever

es
Needle threader

Extension table
(Accessory Box)
uid

Needle clamp screw

Needle thread guide

Needle plate
Presser foot holder
-g

Presser foot holder

clamp screw
Feed dog
all

Presser foot

Bobbin case
Bobbin case cover

6
 All manuals and user guides at all-guides.com

1
Thread winding spindle

Before use (Be sure to read this section before use)

Thread winding Hollow for carrying
switch
( Insert your hand into the hollow
when carrying sewing machine )
Presser foot lever

Handwheel Thread cutter

Battery
holder

Main power
switch
Drop feed lever
** Equipped only with
Terminal box model XXX34
Buttonhole
adjustment screw
Model label

Foot controller

7
 All manuals and user guides at all-guides.com

Part names and their functions

The various parts of the sewing machine have the functions described below.

Presser foot pressure adjustment knob

** Equipped only with model XXX34
•• By turning this knob, the amount of pressure applied by the
presser foot can be adjusted.
•• Turning the knob toward “–” reduces the amount of pressure
applied by the presser foot.
•• For best results when sewing stretch or thin fabrics, slightly
reduce the pressure.
•• Normally, sew with the knob set to “3”.
Drop feed lever
** Equipped only with model XXX34
•• Lower the feed dog when doing free
motion sewing e.g. free motion
embroidery or quilting.
•• During normal sewing, move the lever to
the right to raise the feed dog.
•• When doing free motion sewing, move
the drop feed lever to the left to lower the
Extension table feed dog.
(Accessory Box)
•• Pull out the extension table
(accessory box) in the
direction of the arrow.

Presser foot lever

•• When sewing, lower the presser foot lever to lower the
presser foot. (Position 1)
•• When inserting fabric, lift up the presser foot lever to raise
the presser foot. (Position 2)
•• The presser foot can be raised even higher by raising the
presser foot lever to position 3. Since the presser foot
lever does not remain in this position, hold it in place when
inserting the fabric. This position is useful when sewing
thick fabric.
8
 All manuals and user guides at all-guides.com

Handwheel
•• Use the handwheel to manually raise and lower the needle.

Note:
Always turn the handwheel towards yourself (in the
1
direction of the arrow).
If the handwheel is turned in the opposite direction,

Before use (Be sure to read this section before use)

the thread may become tangled.

For operating details,

refer to pages 23 - 25.
Pattern selection dial and
stitch length dial
Stitch length dial
Turn the dial to adjust the stitch length. Short Long
If a larger number is aligned with the mark above the
dial, the stitch length becomes longer. If a smaller
number is aligned with the mark above the dial, the
stitch length becomes shorter.
Mark above dial

Longer Shorter Longer Shorter

Model XXX34 Model XXX26

Pattern selection dial

Turn the dial until the desired pattern is aligned with the mark above the
dial.
To sew patterns A to K, turn the dial until is aligned with the mark
above the dial.
To sew patterns L to S, turn the dial until is aligned with the mark
above the dial.

Reverse sewing lever

•• Press down the reverse lever, when sewing in
reverse.
•• Remove your finger from the reverse sewing
lever to return to forward direction sewing.
9
 All manuals and user guides at all-guides.com

Quick adviser
The quick adviser (under the lid on the sewing machine) provides various descriptions
such as basic machine operations.

zz Accessing the quick adviser

Flip up the lid to open it.

Quick adviser
(Stored inside)

10
 All manuals and user guides at all-guides.com

How to operate foot controller

Caution
Be sure to use the main power switch to turn off the sewing machine 1
before connecting the foot controller.
Not doing so could cause an injury.

Before use (Be sure to read this section before use)

„„Operation

m
1 Press the “” side of 2 Insert the power cord connector into
the main power switch the terminal box on the machine.
to turn off the sewing
machine.
Main power switch

.co Connector
es
Press the “|” side Step on the foot controller
of the main power to operate the sewing
switch to turn on machine.
the sewing machine.
The more you press the
uid

Main power switch foot controller, the faster

the machine runs.
Foot
controller
Release the foot controller
to stop the machine.
-g
all

11
 All manuals and user guides at all-guides.com

2 Sewing preparations
Connecting the power
Warning
Do not touch the power plug with wet hands.
Doing so could cause an electric shock.

Hold the power plug, to remove or insert into the power outlet.
Not doing so could damage the cord and cause an electric shock, fire or
injury.

Caution
Before plugging in the power cord, use the main power switch to
turn off the sewing machine.
Not doing so could cause an injury.

1 Prepare the foot controller.

Insert the power cord connector
2 into the terminal box.
Insert the power plug into the outlet.

Power plug
Foot controller Terminal box

Connector

Main power switch Press the “|” side (power on) of the
main power switch.
The power is turned on.
ON

OFF

12
 All manuals and user guides at all-guides.com

Installation of battery for winding the lower thread

A battery is supplied as one of the accessories.
Before winding the lower thread, install it in the battery
holder on back of sewing machine.

Caution
When the machine is not used for an
2
extended period, remove the battery.

Sewing preparations
Battery holder

1 Pull the battery holder cover out as

the arrow.

Battery holder cover

2 Install the battery while confirming

polarity of it.
Attach battery holder cover.

Note:
Refer to page 49 when purchasing
or changing batteries.
(Alkaline 1.5 V, Mignon/AA/LR6)

Make sure that the thread winding

spindle rotates by turning the thread
winding switch on by pushing in the
direction of arrow.

Note:
Thread winding spindle rotates while
pushing the switch to the left.
Thread winding switch

13
 All manuals and user guides at all-guides.com

Note:
Winding the lower thread Prepare a
specially
designed bobbin.

1 Turn off the 2 Pull up the spool pin.

sewing machine. Position the spool of thread and the spool
cap on to the spool pin.
Start

Main power switch

Note
A felt was originally put on to the spool
pin.

Complete
Thread guide ( )
8 To stop winding, release the thread winding
switch to the right.

Note
Do not wind excessively,
it causes sewing malfunction.

Remove the bobbin from the spindle. Cut the

thread.

right wrong

7 Push the thread winding

switch to the left again.
Wind the thread to the amount
you need.
6 Cut extra thread above
the bobbin hole.

** Cut the thread so that no

excess extends from the
bobbin hole.

14
 All manuals and user guides at all-guides.com

Caution
While the bobbin is being wound, do not touch the thread winding
spindle or the handwheel.
Doing so could cause an injury.

Pull the thread from the thread

Spool cap
spool, and then hold it with
Spool of thread one hand while passing it
around the thread guide with
2
Felt the other hand, as shown.
Thread guide

Sewing preparations
Spool pin

Spool pin ( 2 )

Thread winding switch

( 7 8 ) Pass the thread end through
the hole in the bobbin as
shown.
Place the bobbin on the
Thread winding spindle thread winding spindle so the
( 6 8 ) groove aligns with the shaft
projection.
Main power Thread
switch ( 1 ) Hole
Groove
Bobbin
Thread
winding
spindle Shaft
projection

1 Hold the thread end and push the thread

winding switch to the left and start winding.
2 After winding a little, release the thread
winding switch to the right and stop winding.
Note
While pushing the winding switch to the
left, thread winding spindle rotates.

15
 All manuals and user guides at all-guides.com

Threading the lower thread

Open the bobbin case cover, and insert the bobbin into the bobbin case.
If the bobbin is incorrectly inserted into the bobbin case, the stitching will not be sewn
correctly.

1 Turn off the sewing machine. Main power switch

m
2 Pull the bobbin case cover
towards yourself. .co
es
uid

Bobbin case
cover
-g

Insert the bobbin so that it rotates

counterclockwise.

Bobbin Thread unwinding direction

all

Counterclockwise Clockwise

Bobbin case Check the orientation of the bobbin.

16
 All manuals and user guides at all-guides.com

Pass the thread through A, then B, and then pull the thread to
the rear, as shown below.

B 2

Sewing preparations
A

Pull out about 15 cm of thread to

the rear.

15 cm

6 Fit the projections on the bobbin case cover into the race
retainer grooves, and then push the bobbin case cover closed.

Groove
Projection

Bobbin case
Bobbin case cover
cover

17
 All manuals and user guides at all-guides.com

Threading the upper thread

1 Turn off the 2 Raise the presser foot lever.

sewing machine.

Main power switch

Start

Presser foot lever

Thread guide ( )
Complete

9 Pass the thread through

the presser foot, and then
pull out about 15 cm of Take-up lever
thread to the rear. ( 6 )

Needle thread guide ( 7 )

Eye of needle ( 8 )
Presser foot ( 9 )
15 cm
Presser foot
lever ( 2 )

8 From the front, 7 Pass the thread through the needle thread guide.
pass the thread Needle thread guide
through the eye
of the needle.
** When using
the needle
threader, Needle
refer to thread guide
page 20.
The thread can easily be passed through the
needle thread guide by holding the thread in
Eye of needle your left hand, then feeding the thread with your
right hand, as shown.

18
 All manuals and user guides at all-guides.com

Turn the handwheel towards Pull up the spool pin.

yourself to raise the take-up Position the spool of
lever. thread and the spool cap
Handwheel Take-up lever on to the spool pin.
Spool cap 2
Spool of thread

Sewing preparations
Felt
Spool
pin

Spool pin ( ) 1 Pull the thread from

the thread spool, and
hold it with one hand.
Handwheel ( )
2 Pass the thread
around the thread
guide with the other
hand, as shown.
Main power switch
( 1 ) Thread guide

6 3 Pull the thread Check that the Pass the thread in The thread
down along the take-up lever the order shown. should be taut
groove, and then is correctly (3 through 5) and secure.
pull it back up. threaded.
4 Pass the thread
through the take-
up lever from the
right.
5 Pull the thread
down along the
Take-up
groove.
lever

19
 All manuals and user guides at all-guides.com

Using the needle threader

Caution
Before using the needle threader, use the main power switch to turn
off the sewing machine.
Not doing so could cause an injury.

** Use sewing machine needles No. 11/75 to 16/100 with the needle threader.
(Needle No 14/90 is included when the sewing machine is purchased.)
The needle cannot be threaded if the thread is too thick for the needle. For details
on possible needle and thread combinations, refer to “Relationship between the
needle, thread and fabric, and adjusting the thread tension” on page 29.
zz Preparing to use the needle threader
1 Turn the handwheel towards 2 Turn the pattern selection dial
yourself until the needle is in to “6” (straight stitch).
its highest position.
** Otherwise, the needle threader
** If the needle is not in its may not operate correctly and
highest position, the needle the needle may not be threaded.
cannot be threaded. 6

Pattern selection
dial

Raise the presser foot lever. Check that the thread has
been passed through the
needle thread guide.

Needle thread
Presser foot lever guide

zz Understanding the needle threader mechanism

1Lower
The hook is within the guide.
The hook passes through
the needle, catches the
Needle thread, then pulls the thread
through the needle.
2Turn Guide Hook
20
 All manuals and user guides at all-guides.com

zz Using the needle threader

1 While fully lowering the needle
threader lever, hook the thread
on the guide as shown in the
diagram.
Needle threader
lever

Guide
2

Sewing preparations
2 Fully turn the needle threader
lever to the rear, and pull the

.co
thread through the needle
threader slot.

Needle threader slot

es
1 Slowly return the needle threader
lever towards yourself as much
as possible.
uid

2 Check that the thread has passed

through the eye of the needle.
3 Release the needle threader lever
while releasing the end of the
thread.
** If the needle is not threaded, check
-g

that the needle has been raised to its

highest position, and then repeat the
procedure starting with step 1 .
all

Pull the thread loop that formed behind the needle, and then pull about
15 cm of thread to the rear.

15 cm

21
 All manuals and user guides at all-guides.com

Pulling up the lower thread

1 Raise the presser

foot lever. Loosely Do not pull the
hold the upper thread taut.
thread with your
left hand, and then
turn the handwheel
towards yourself
one full turn.

2 Lightly pull the upper thread with

your left hand to pull up the lower
thread.

Pull out the lower thread to the front.

Align both threads, pass them

through the groove (arrow) and
Presser
under the presser foot, and then foot
pull out about 15 cm of thread to
the rear. 15 cm

22
 All manuals and user guides at all-guides.com

Application of each stitch pattern

Caution
Before turning the pattern selection dial, use the main power switch
to turn off the sewing machine.
Not doing so could cause an injury.
Do not turn the pattern selection dial while the needle is lowered.
Doing so could break the needle and cause an injury. 2
Turn the handwheel towards yourself to raise the needle to its highest position;
otherwise, the pattern and stitch length may not be correctly adjusted.

Sewing preparations
„„When sewing patterns 1 to 15
Mark above dial

The length The length

becomes becomes
longer shorter
Turn the dial until the desired pattern
1 aligns with the mark above the dial.
Turn the stitch length dial until the desired
2 stitch length aligns with the mark above
the dial.
** The stitch length can be set between 0 and 4. Stitch
Since the recommended range differs depending Pattern
length dial
on the pattern, refer to the following table. selection dial

Pattern Stitch length dial Pattern Stitch length dial

selection Application (recommended Presser foot selection Application (recommended Presser foot
dial No. setting) dial No. setting)
Buttonhole 10 Mending stitch
0-4 foot 0-4
Buttonhole Thin fabric
(0.4~1) (1~2)
overcasting

11
5 Zigzag sewing Decorative stitch 0-4
Straight stitch 0-4 Overcasting (1~2)
foot
(left side) (1~4)

12 Zigzag sewing
Straight stitch 0-4 0-4
(center) (1~4) Decorative stitch foot
6 (1~2)
Zipper foot
0-4 13
Zipper insertion
(2~4) 0-4
Decorative stitch
(1~2)
Blind stitch
7 foot * 14
0-4 Zigzag stitch 0-4
Blind hem stitch
(1~2) (medium) (0.5~2)

Zigzag sewing Zigzag stitch (large) 0-4

8 foot Overcasting (1~4)
0-4 15
Decorative stitch Overcasting
(1~4)
foot *
0-4
Overcasting
(1~4)
Blind stitch
9 foot *
Stretch fabric blind 0-4
hem stitch (1~2) ** Included only with model XXX34.
The zigzag sewing foot can also be used for 7, 9, 15.

23
 All manuals and user guides at all-guides.com

Caution
Before turning the pattern selection dial, use the main power switch
to turn off the sewing machine.
Not doing so could cause an injury.

„„When sewing patterns A to K

Mark above dial

Turn the dial until the desired
1 pattern aligns with the mark Stitch length dial
Mark above dial
above the dial.
Turn the stitch length dial
2 until aligns with the mark
above the dial.
** The stitch length is fixed at 3 mm and
cannot be adjusted.
Pattern Turn to the left
selection dial

Pattern Stitch length dial Pattern Stitch length dial

selection Application (recommended Presser foot selection Application (recommended Presser foot
dial No. setting) dial No. setting)

A G
Reinforced straight
stitch Decorative stitch
(left side) Overlock

B H
Reinforced straight
stitch Decorative stitch
(center) Overlock

Zigzag sewing
C I foot
Decorative stitch
Double overlock Zigzag sewing Decorative stitch
foot

D J
Reinforced
Decorative stitch zigzag stitch
(medium)

E K
Reinforced
Decorative stitch zigzag stitch
(large)

F
Decorative stitch

24
 All manuals and user guides at all-guides.com

Caution
Do not turn the pattern selection dial while the needle is lowered.
Doing so could break the needle and cause an injury.

„„When sewing patterns L to S

** Stitches L through S can be sewn only with model XXX34.
2

Sewing preparations
Mark above dial
Turn the dial until the desired
1 pattern aligns with the mark Stitch length dial
Mark above dial
above the dial. Pattern
selection
dial
Turn the stitch length dial
2 until aligns with the mark
above the dial.
** The stitch length is fixed at 3 mm
and cannot be adjusted.
Turn to the left

Stitch length Stitch length

Pattern Pattern
dial dial
selection Application Presser foot selection Application Presser foot
(recommended (recommended
dial No. dial No.
setting) setting)
L R
Decorative stitch Decorative stitch Zigzag sewing
foot

M S
Decorative stitch Decorative stitch

N
Fagoting Zigzag sewing
foot

O
Appliqué

P
Appliqué

Q
Decorative stitch

25
 All manuals and user guides at all-guides.com

Changing the presser foot

Caution
Before changing the presser foot, use the main power switch to turn
off the sewing machine.
Not doing so could cause an injury.

zz Removal

m
1 Raise the presser foot lever. 2 Turn the handwheel towards
yourself to raise the needle.

.co Note:
Never turn in the wrong direction.

Handwheel
es
Presser foot lever
uid

Press the presser foot holder lever in

-g

the direction of the arrow to release

the presser foot.
all

Presser foot
holder lever

Presser foot

26
 All manuals and user guides at all-guides.com

zz Installation
1 Position the presser foot pin
directly below the groove in the
presser foot holder.
Presser foot
holder

2
Groove

Sewing preparations
Presser foot pin

2 Lower the presser foot lever to

Presser foot lever
secure the presser foot.

Tip
In order to avoid losing the presser foot, we recommend storing the machine when it is
not being used with the needle and the presser foot lowered.

27
 All manuals and user guides at all-guides.com

Changing the needle

Caution
Before changing the needle, use the main power switch to turn off the
sewing machine.
Not doing so could cause an injury.
Broken needles are dangerous. Be sure to dispose of them in a safe
place away from children.
Not doing so could cause an injury.

1 Turn the handwheel towards yourself to

Screw driver for
raise the point of the needle higher than the
needle plate. the needle plate

2 Hold the needle in one hand, loosen the

needle clamp screw with the screw driver for
the needle plate, and remove the needle.

Note: Needle clamp

Do not remove the needle clamp screw. screw
Loosen the needle clamp screw to remove
the needle.

Face the flat surface of the Flat surface

needle to the rear and insert until
it makes contact with the pin.
Firmly tighten the needle clamp Pin
screw with the screw driver for
the needle plate.

zz Correct needle selection

If a faulty needle is used, not only could it impair the sewing performance, but it could
also damage the needle plate or hook, or break the needle.
Good needle ** Incorrect stitching or thread breaking, try replacing the
needle.

ÍFaulty needle

The entire needle is The point of the needle The point of the needle
bent is crushed / worn away is bent
28
 All manuals and user guides at all-guides.com

Relationship between the needle,

thread and fabric, and adjusting the
thread tension
The quality of the sewing finish will improve if the needle and thread are changed to
match the type of fabric. Follow the directions in the table below.
2
Thin fabrics Normal fabrics Thick fabrics
Relationship between the needle,

Sewing preparations
No. 11/75 No. 14/90 No. 16/100
Needle
thread and fabric

Polyester No. 50 to Polyester No. 30 to

Polyester No. 90
No. 60 No. 50
Cotton No. 80 to No. 120
Cotton No. 60 to No. 80 Cotton No. 40 to No. 50
Silk No. 80
Thread Silk No. 50 to No. 80 Silk No. 50
Normal front cloth Curtains
Normal back cloth
Broad Denim
Quipler
Soft denim Quilting
Georgette
Satin Fleece
Lawn
Fabric Pile Tweed
Lace, etc.
Gingham, etc. Felt, etc.
Reference thread tension

-3 -1 +1

-2 +2
+1 +3
-1
Upper +2 +4

thread -1 ~ -3 +1 ~ +3
tension
dial

• Use a ball point needle for the sewing alignment of stretch fabric.
• Please purchase any needles not included as accessories, after checking they are
specified as home-use sewing machine needles.
• Use the same kind of threads for upper/lower thread.
• The bigger the needle number is , the thicker the needle is, the bigger the thread
number is, the thinner the thread is.
• Normally, sew with the upper thread tension dial set to “ ”.

29
 All manuals and user guides at all-guides.com

3 Sewing
Straight stitching and reverse sewing
Caution
Do not pull the fabric excessively while sewing.
Doing so could break the needle and cause an injury.

zz Straight stitch
1 Turn the handwheel towards yourself to raise the needle.

Turn the pattern selection dial to choose the pattern.

2 Set the stitch length dial between “1” and “4”.

1~4
Zigzag sewing foot
(Originally attached to
the sewing machine)
5 6

(For details on changing the presser foot,

refer to “Changing the presser foot” on page 26.)
1
Position the fabric and lower the presser
foot lever.
Step on the foot controller to begin sewing.

z1z End of sewing

After sewing, turn handwheel towards

yourself until the needle is in the highest
position.
Raise the presser foot and pull out the fabric
to the rear.

30
 All manuals and user guides at all-guides.com

zz Thread cutter

Line up the two threads, and cut Thread cutter

them with the thread cutter on the
presser bar.

m
3

.co
zz Reverse sewing
Reverse sewing is performed at the beginning and the end of sewing to prevent the

Sewing
thread from unraveling.

Reverse sewing is performed while

es
pressing down the reverse sewing
lever.

• Stitch 1 cm from the edge of the

fabric to prevent unraveling at the
uid

start of sewing.
• Sew 3 to 4 reverse stitches at the
end of sewing.
Note:
Remove your finger from the
reverse sewing lever to return to Reverse sewing
-g

forward direction sewing. lever

all

31
 All manuals and user guides at all-guides.com

zz Sewing thick fabric

When sewing over thick fabric, the
presser foot may tilt and be unable to
feed through the fabric.

Place fabric or thick paper of the

same thickness as the fabric you
wish to sew under the presser foot.
This will enable smooth sewing.

Fabric or thick Sewing fabric

paper

zz Sewing thin fabric

When sewing thin fabric, sometimes
fabric puckers or is not fed
correctly.
At that time, sewing is easier if
tissue paper is placed under the
fabric. Tissue paper
After sewing remove the paper
carefully.

zz Sewing hard-to-feed fabric

When sewing hard-to-feed fabric,
such as leather, use the roller foot.
** The roller foot is only included with
model XXX34.

32
 All manuals and user guides at all-guides.com

zz Sewing tube-shaped fabrics

1
1 Pull out the extension table
(accessory box) in the direction of the
arrow.

3
1

Sewing
2 Sew tube-shaped fabrics such as
trousers or sleeves, by pulling them
over the machine free arm as shown
in the diragram.

33
 All manuals and user guides at all-guides.com

Zigzag sewing
There are various zigzag applications, such as applique and overcasting.
1
1 Turn the handwheel towards yourself to raise the needle.

2 Turn the pattern selection dial to choose the pattern.

Set the stitch length dial between “0.5” and “4”.

0.5~4
Zigzag sewing foot
(Originally attached to
the sewing machine)
14 15

2.5 5.0 mm

(For details on changing the presser foot, refer to “Changing the presser
foot” on page 26.)

1
Position the fabric and lower the presser
foot.
Step on the foot controller to begin
sewing.

34
 All manuals and user guides at all-guides.com

Adjusting thread tension

zz Adjustment method for upper thread tension

Straight stitch

Upper thread is tight

Wrong • Upper thread is tight

side

Right side 3

Sewing
Upper thread is loose
Lower the upper thread tension.
Wrong
side

Right side

• Upper thread is loose

Zigzag sewing

Upper thread is tight

Right side

Increase the upper thread tension.

Wrong
side
Note:
If the tension does not change even when you
Upper thread is loose
adjust the upper thread tension, thread the
Right side upper thread and lower thread again.

Wrong
side

35
 All manuals and user guides at all-guides.com

Buttonhole sewing
Buttonhole sewing to match the size of the button is possible.
For stretch fabric or thin fabric, it is recommended to use a stabilizer for a better
buttonhole finish.

Caution
Before changing the presser foot, use the main power switch to turn
off the sewing machine.

m
Not doing so could cause an injury.
1
1 Change to the buttonhole foot.

.co
Set the stitch length dial between “0.4” and “1”.

0.4~1

Buttonhole foot 1 2 3 4
es
uid

(For details on changing the presser foot, refer to “Changing the presser
foot” on page 26.)
1
2 Set the buttonhole size and Center line
-g

mark lines on the fabric. 3 mm

Buttonhole
size

Start line of
all

sewing

Button thickness
(Button diameter+button thickness+3mm)
1
Align the buttonhole foot Division line
division line closest to you
with the guide line, and lower
the presser foot to the start Start line of sewing
line of sewing on the fabric.
Guide line
Center line
36
 All manuals and user guides at all-guides.com

Raise the needle to the highest

position, set the pattern dial to “1”,
sew the left side and stop at the line
marked on the fabric.

Raise the needle to the highest

position, set the pattern dial to “2”,
and sew 5 to 6 bar-tack stitches. 3
“2” and “4” on the pattern selection
dial use the same dial position.

Sewing
6 Raise the needle to the highest
position, set the pattern dial to “3”,
sew the right side and stop at the line
marked on the fabric.

7 Raise the needle to the highest

position, set the pattern dial to “4”,
and sew 5 to 6 bar-tack stitches.

37
 All manuals and user guides at all-guides.com

Caution
When using the buttonhole cutter to cut the buttonholes, do not hold
the fabric in front of the cutter.
Doing so could cause an injury to your hand.

8 Use the buttonhole cutter to cut the

center, making sure not to cut the
stitches.
Buttonhole
Note: cutter
If a marking pin is put in the bar-
tack area it helps to prevent cutting
the bar-tack with the buttonhole
cutter.

zz Adjustment of buttonhole balance

• Use the buttonhole adjustment
screw to adjust the balance between
the stitches (rear side).
• Adjust by turning with the - screw
driver of your own.
• Don’t turn the screw more than 90°.
Note:
The original position of buttonhole Buttonhole
adjustment screw may vary adjustment
according to the model of machine. screw

If the stitches are loose on the right If the stitches are loose on the left
side of the buttonhole, turn slightly side of the buttonhole, turn slightly
in the “-” direction. in the “+” direction.

38
 All manuals and user guides at all-guides.com

Overcasting
This is a sewing method that prevents unraveling at the edge of the fabric.

Caution
Before changing the presser foot, use the main power switch to turn
off the sewing machine.
Not doing so could cause an injury.

1 Change to the zigzag sewing foot or the overcasting foot.

Set the stitch length dial between “1” and “4”.

Note: 3
Select pattern No.10 when sewing thin fabric.

Sewing
Zigzag sewing foot
1~4

10 15
Overcasting foot

**The overcasting foot is only

included with model
XXX34.

(For details on changing the presser foot, refer to “Changing the presser
foot” on page 26.)

z8
z When using the zigzag sewing foot

2 Position the fabric so that the

Right needle entry
needle extends slightly off the
point
edge of the fabric when the
needle moves to the right.

z8
z When using the overcasting foot

2 Sew with the edge of the fabric

against the guide on the foot.

Guide

Caution
Do not use stitch number 10 with the overcasting foot.
Doing so may cause the needle to hit the presser foot and break or cause
injuries.
39
 All manuals and user guides at all-guides.com

Zipper insertion
Caution
Before changing the presser foot, use the main power switch to turn
off the sewing machine.
Not doing so could cause an injury.

1 Change to the zipper foot.

Set the stitch length dial between “2” and “4”.
2~4

Zipper foot
6

(For details on changing the presser foot, refer to “Changing the presser
foot” on page 26.)

z8z Sewing the left side of the zipper

2 Set the right side pin of the
zipper foot to the presser foot Right side pin
holder.
Needle entry
point

Align the zipper and the fabric,

and tack. Tack

8
Position the fabric so that the
zipper is on the right side of the
presser foot.
Zipper

40
 All manuals and user guides at all-guides.com

8
Sew until just before the presser foot
makes contact with the slider, and
then stop the sewing machine.
Slider

m
6 Turn the handwheel towards yourself
to lower the needle into the fabric.
3
7 Raise the presser foot.

.co

Sewing
Move the slider to the rear of the Slider
8 presser foot, and finish the sewing.
es
z8z Sewing the right side of the zipper
9 Release the presser foot and set to
uid

the left side pin.

Sew the right side of the zipper using
the same procedures as for the left
side.

Note:
-g

Sewing in the same direction as the

left side will help prevent sewing
misalignment.
all

41
 All manuals and user guides at all-guides.com

Blind hem stitching

In this sewing method the stitch cannot be seen on the front of the fabric.
Caution
Before changing the presser foot, use the main power switch to turn
off the sewing machine.
Not doing so could cause an injury.
8
1 Change to the zigzag sewing foot or the blind stitch foot.
Set the stitch length dial between “1” and “2”.

Zigzag sewing foot 1~2

7 9
Blind stitch foot

** The blind stitch foot

is only included with
model XXX34.

(For details on changing the presser foot, refer to “Changing the presser
foot” on page 26.)

2 Sew overcasting along the edge of the fabric, and then fold the fabric as shown.
** Tack or iron a crease 6 to 8 mm from the edge of the fabric.
6 - 8 mm

Wrong Right Wrong Right

side side side side

Overcasting Tacking or crease

At the tacking or the crease Fold

(tacking or crease)
that was ironed, fold back the
fabric so that wrong side faces Wrong side
upward. Overcasting

Turn the handwheel towards yourself

Needle on the left side
until the needle is on the left side.

42
 All manuals and user guides at all-guides.com

Position the fabric so that the needle slightly catches the fold.
Zigzag sewing foot Blind stitch foot
Fold
Fold
Needle on Needle on
the left side the left side

zz When using the zigzag sewing foot

3
6 Lower the presser foot, and start sewing.
The part of the stitch that catches the fold
will be visible from the right side of the

Sewing
fabric. Sew evenly so that the stitching is
not too large or too small.
Fold

zz When using the blind stitch foot

6 Lower the presser foot, adjust the screw
so that the fold aligns with the guide, and
Adjusting
screw
then sew with the fold against the guide.
Fold
Wrong
side

Guide

7 After sewing, pull out the tacking, and fold out the fabric.

„„Balanced stitches „„Troubleshooting

Small stitches evenly Needle catches too Needle does not
located on right side. much on the fold catch on the fold
Wrong Right Wrong Right Wrong Right
side side side side side side

(When unfolded) Large stitches on right side. The blind hem stitches
do not come through
43
 All manuals and user guides at all-guides.com

4 Maintenance
Cleaning and maintenance must not be made by children without proper supervision.

Feed dog and hook maintenance

If the sewing machine makes a loud noise or rotates slowly, there could be thread waste
or dust in the hook or feed dog. Perform maintenance on the hook and the feed dog.

Caution
Before cleaning the hook, use the main power switch to turn off the
sewing machine, and then remove the power plug from the outlet.
Not doing so could cause an injury.

Attention
Do not use detergent, bleach, benzine, or thinner chemical cloths.
Doing so could cause discoloration or cracking.

z8z Cleaning the feed dog and hook

1 Remove the presser foot and the needle.
Turn the pattern selection dial to “6”, and then turn the handwheel
towards yourself to raise the feed dog.

Handwheel

Pattern selection dial Feed dog

44
 All manuals and user guides at all-guides.com

2 Use the screwdriver for

the needle plate to loosen
Lift up the bobbin case so that part c
is moved past part d, as shown.
the screws in the needle
plate, and then remove the
needle plate.

c d

Pull out the bobbin case in the

direction of the arrow to remove it.

Note:

4
Do not pull with excessive force,
otherwise the bobbin case may be
scratched.

** If the bobbin case cannot be pulled out,

Maintenance
repeat the procedure starting with step
.

Remove any lint or dust from the

feed dog and hook, and then wipe
them with a soft cloth.
A vacuum cleaner can be used to
remove lint and dust.

Feed dog

Hook

45
 All manuals and user guides at all-guides.com

zz Attaching the Bobbin Case

1 Position the bobbin case so 2 With the bobbin case tilted to

that part a on the bobbin case the left, insert the left side of
is below part b on the sewing the bobbin case into the hook,
machine. as shown.
b Left side of
bobbin case

m
a

.co
Insert the right side of the bobbin
case into the hook so that part c on
es
the bobbin case is to the left of part d
on the sewing machine.
Right side of
c d bobbin case
uid

Make sure that the bobbin case is fully installed in the hook.
Edge of hook
Make sure that
the bobbin case
-g

moves slightly in
the direction of
the arrow.
c d
all

<When correctly installed> <When incorrectly installed>

• The entire bobbin case fits into the • The right side of the bobbin case
hook so that the edge of the hook is covers the edge of the hook and
visible. the bobbin case is tilted.
• Part c on the bobbin case is to the left
of part d on the sewing machine.
Note:
Carefully check the bobbin case since it may be incorrectly installed
even though part c of the bobbin case is to the left of part d on the
machine, as shown in the above diagram on the right.

46
 All manuals and user guides at all-guides.com

Attach the needle plate with red mark

a on the bobbin case positioned as
shown in the diagram.

6 1 Tighten the needle plate screws.

2 Attach the presser foot and insert the
needle.
3 Check that the needle correctly enters the
hole in the needle plate. 4
** If the bobbin case is not installed correctly,

Maintenance
the handwheel does not turn smoothly. If this
occurs, remove the needle plate and bobbin
case, and attach them again.

47
 All manuals and user guides at all-guides.com

Changing light bulb

Warning
Before changing the light bulb, use the main power switch to turn off
the sewing machine, remove the power plug from the outlet, and then
wait until the bulb cools.
Not doing so could cause a burn or electric shock.

8
1 Loosen the screw with a
Screw
+ screw driver of your
own, and take off the face
cover in the direction of
the arrow.

Face cover

8
2 Turn the light bulb
counterclockwise as the arrow in
the diagram and remove.

Turn the new light bulb clockwise

to install.

Note:
Use a light bulb with a maximum
power of 15 W.

Always reinstall the face cover after

replacing the light bulb.

48
 All manuals and user guides at all-guides.com

Servicing double-insulated products

(230V-240V)
In a double-insulated product, two systems of insulation are provided instead of
grounding. No grounding means are provided on a double-insulated product nor should
a means for grounding be added to the product. Servicing a double-insulated product
requires extreme care and should only be done by qualified service personnel with
knowledge of the system under his or her responsibility. Replacement parts for a double-
insulated product must be identical to those parts in the product. The symbol is marked
on the double-insulated product.

Notice about the incandescent lamp

The incandescent lamp fitted to our product is not suitable for household lighting and is
specifically designed for the lighting of the sewing machine sewing area. 4

Maintenance
Safety precaution about the battery
Warning
If the alkaline solution from the battery should get in the eyes or come
into contact with the skin or clothes, rinse with a large quantity of
clean water and consult a doctor immediately.
Not doing so could cause an injury.

Caution
1. Do not short-circuit, disassemble, heat, recharge, deform, dispose
of in fire.
2. Do not insert batteries in reverse polarity.
3. Do not expose batteries to strong impact by dropping or throwing
the batteries.
Doing so could cause a leakage of alkaline solution.

49
 All manuals and user guides at all-guides.com

Troubleshooting
What is the problem? Check the following possibilities before contacting the service
center for repair.

Trouble Cause Countermeasure Page

The power plug is not Connect the power plug
12
inserted correctly
Machine The main power switch has
Turn on the sewing machine 12
does not been turned off
work Thread is tangled in the
hook, or there is a broken Clean the hook 44
needle in the hook
Machine very
There is lint or fluff in the Remove the lint or fluff from
noisy & very 44
hook or feed dog the hook or feed dog
slow
Needle incorrectly inserted
Insert the needle correctly 28
into the machine
The needle clamp screw is
Firmly tighten the screw 28
loose
Needle
The needle is too fine for the Use the appropriate size
keeps 29
fabric needle for the fabric
breaking
The upper thread tension is
Loosen the upper tension 35
too tight
The bobbin case is not in the Put the bobbin case in the
46
correct position correct position
Machine is incorrectly
Rethread the sewing machine 16-19
threaded
The thread is tangled in the Remove the thread tangle and
44
bobbin case or hook clean the feed dog and hook
The upper thread tension is
Upper thread too tight Loosen the upper tension 35
keeps
Breaking The needle is bent or the
Insert a new needle 28
needle point is burred
The needle is incorrectly
Insert the needle correctly 28
inserted
The thread is a poor quality Use a good quality,
―
thread recommended thread
Lower
Lower thread is incorrectly
thread keeps Rethread the bobbin case 16, 17
threaded
breaking

50
 All manuals and user guides at all-guides.com

Trouble Cause Countermeasure Page

Remove any lint and fluff from
The feed dog is dirty 44
the feed dog
Pattern selection dial set to
Reset the stitch selection dial
a buttonhole number – “2” 23
to the desired stitch
or “4”.
Fabric not
feeding The feed dog is lowered Raise the feed dog 8
through the The stitch length dial is set
machine Adjust the stitch length dial 23-25
to “0”

m
Adjust the stitch length dial to
The stitch length is too short 23-25
an appropriate setting
The presser foot pressure is Increase the presser foot
8
too light pressure

.co
The needle is incorrectly
Insert the needle correctly 28
inserted
The needle is bent Use a straight needle 28
Missed
stitches Needle and thread not
suitable for the fabric
Use the correct needle and
thread for the fabric
29 4
es
Rethread the upper thread
Incorrect upper threading 18, 19
correctly

Maintenance
The tension of the upper
Adjust the thread tension 35
thread is too tight
The machine is incorrectly
uid

The fabric Rethread the machine 16-19

threaded
wrinkles /
Needle is too thick for the Use a finer needle to suit the
puckers 29
fabric fabric
The needle is burred Insert a new needle 28
Stretch fabric is being sewn Use the ball point needle 29
-g

Incorrect bobbin threading Rethread the bobbin correctly 16, 17

Lower thread
The tension of the upper
showing on Adjust the thread tension 35
thread is too tight
the top of the
Incorrect plastic bobbin used Only use the designated
all

fabric 14
or a metal bobbin is used TOYOTA bobbin
Upper thread The tension of the upper
Adjust the thread tension 35
showing on thread is too loose
the under Incorrect upper threading
side of the Rethread the upper thread
(not threaded through the 18, 19
fabric correctly
thread guide)

51
 All manuals and user guides at all-guides.com

Trouble Cause Countermeasure Page

The stitch length dial is not
Set the stitch length dial to the
set to setting “A – K” or “L – 23-25
Unable to appropriate setting
S”
sew stretch
stitches The stitch length dial and the Select the same setting on
stitch pattern selection dial the stitch length dial and the 23-25
settings do not correspond pattern selection dial
The needle position is too Turn the handwheel so that the
20
low line is at the top
The needle Needle no. 9/65 is being Use needle sizes 11/75 to
cannot be 29
used 16/100
threaded with
Needle incorrectly inserted Insert the needle correctly 28
the needle
threader The needle is bent Use a straight needle 28
Threading of the needle Rethread the needle thread
18
thread guide incorrect guide correctly

If the above treatments do not solve the problem, contact the service center as
described in your warranty.
When calling for service, please note the MODEL and SERIES that are inscribed on the
back of your sewing machine.

SP200 SERIES / SERIE MODEL / MODELE

Manufacturer/ : ZHEJIANG AISIN ELITE

Fabricant MACHINERY & ELECTRIC
CO., LTD.P.R.C.
Importer/ :
Importateur
Designed and engineered by
AISIN SEIKI JAPAN

MADE IN P. R. C. / FABRIQUE A P.R.C.

52
 All manuals and user guides at all-guides.com

5 Others
Recycling
DO NOT THROW AWAY!

EU ONLY
We are committed to the protection of the environment. We strive to minimize the
environmental impact of our products by continuously improving product design and our
manufacturing methods.

At end of life please dispose of this product in an environmentally responsible way.

The crossed-out wheelie bin symbol featured above and on the product’s data-
plate means that this product falls under the scope of the E.U. “Waste Electrical
and Electronic Equipment” (WEEE) directive and “Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic Equipment” (ROHS) directive and
should not be disposed of with your household waste. At end of life, you must ensure
that this product is disposed of in accordance with national and local legislation and that
it is sorted as Category 2 “Small Domestic Appliances” WEEE. You may be liable under
local and national laws for improper disposal of this product. Please consult the web, or
a competent national or local body, for the return and collections systems available to
you and the locations of your nearest recycling points. If you purchase a new product
direct from us we will take your old product back, irrespective of the brand, if it is a like
5
for like sale.

Others
As an individual you can make a positive impact on reuse, recycling and other forms
of recovery of WEEE. This will reduce use of landfill and minimize the environmental
impact of the products you use.

Hazardous substances in electronic and electrical products can have a harmful impact
on human health and on the environment.

53
 All manuals and user guides at all-guides.com

Specifications

SP200 Series
Model XXX26/XXX34
Hook type Horizontal
Needle Home-use sewing machine needle
(HA-1)
Bobbin TOYOTA-exclusive plastic bobbin
Maximum stitch length 4 mm
Maximum stitch width 5 mm
Straight stitch needle position Center needle position, left needle
position
Sewing machine weight 5.0 kg
(main unit)
Sewing machine size Width: 412 mm
Depth: 192 mm
Height: 292 mm
Rated voltage 220 - 240V
Rated frequency 50 Hz
Rated power consumption 65 W
Light bulb 15 W
Battery Alkaline 1.5 V, Mignon/AA/LR6

54
 All manuals and user guides at all-guides.com

EU ONLY
Imported by / Importé par :

Web: www.home-sewing.com
Head Office Avenue de l’Industrie 21, Parc Industriel, 1420 Braine-L’Alleud BELGIUM
TEL: +32 (0) 2 387 1817 FAX: +32 (0) 2 387 1995
UK Branch Unit 4, Swan Business Park, Sandpit Road, Dartford, Kent, DA1 5ED UK.
TEL: +44 (0) 1322 291137 FAX: +44 (0) 1322 279214
France Branch 70 chemin de la chapelle Saint Antoine 95300 Ennery, France
TEL: +33 (0) 1 34 30 25 00 FAX: +33 (0) 1 34 30 25 01
Holland Branch Energieweg 14, 2382 NJ Zoeterwoude (Rijndijk), THE NETHERLANDS
TEL: +31 (0) 71 5410251 FAX: +31 (0) 71 5413707
Austria Branch Donaufelder Straße 101/5/1, A-1210 Wien, AUSTRIA
TEL: +43 (0) 1 812 06 33 FAX: +43 (0) 1 812 06 33-11