CHAPTER 7: FLAME CUTTING QUIZ 3
Name Date
Class Instructor Grade
INSTRUCTIONS
Carefully read Chapter 7 in the textbook and answer each question.
MATCHING
In the space provided to the left of Column A, write the letter from Column B that best answers or completes the statement in
Column A.
Column A Column B
o 1. High-pressure valve seats on a regulator that leak result in a creep on the working pressure a use a dry, oil-
gauge. . free rag
i 2. The outlet connection on a regulator is a right-hand_fitting for oxygen. b loose tip
3. How can a regulator adjusting screw be cleaned if it becomes tight and difficult to turn? use . c reverse flow
______
a dry, oil-free rag. . valve
k___ 4. If a torch hose fitting leaks, then the seat should be repaired or replaced. d leaving a film
b 5. A loose tip can cause a torch tip to backfire. . e as low as
. possible
t ___ 6. To stop a flashback, close the oxygen valve on the torch quickly. f oxides
7. The reverse _flow valve is a spring-loaded check valve that closes when gas tries to flow . manufacturer’s
backward through the torch valves. g procedure
8. What do you need to follow to test a flashback arrestor? manufacturer’s procedure. . h numbering
____
. system
s___ 9. Fuel gas hoses must be red and have left-hand threaded fittings. i right-hand
r 10 When hoses are not in use, the gas must be turned off and the pressure bled off. . j fitting
angle
.
11 .
k repaired or
d . A leak-detecting solution must produce a good quantity of bubbles without leaving a film. . replaced
qq 12 Dirty tips can be cleaned using a set of tip cleaners. l actual work
______ .
13 Manifolds must be located 20 ft (6 m) or more from the actual work. . m chalk line
14 Set the manifold line pressure as low as possible, still ensuring that the type of work being n preheat holes
. done at the workstations can be performed satisfactorily. .
To make a hand cut, the torch may be moved by sliding it toward you over your supporting creep
p 15 hand. o
.16 A slight forward torch angle helps the flame preheat the metal. . p sliding
n___ . The proper alignment of the preheat holes will speed up and improve the cut. . tip cleaners
m - 17
18 A chalk line will make a long, straight line on metal and is best used on large jobs. qr bled off
h___ 19 Each welding equipment manufacturer uses its own numbering system to designate the tip s red
. size. .
f___ 20 Some metals release harmful oxides when they are cut. t flashback
. .
CHAPTER 7: FLAME CUTTING QUIZ 5
Name________________________________________________________________Date __________________
Class _________________________Instructor ________________________________________Grade ________
INSTRUCTIONS
Carefully read Chapter 7 in the textbook and answer each question.
IDENTIFICATION
Identify the numbered items on the drawing by writing the letter next to the identifying term in the space provided.
1 _ _ CUTTING OXYGEN
. _
2
. _ CUTTING TIP
_
3 _ CUTTING OXYGEN
. VALVE LEVER
_
4 _
. _ PREHEAT FUEL
j
_
5 _ _ OUTER FLAME
. ENVELOPE
_
6 _ _ CUTTING OXYGEN
. a TUBE
_
7 _ _
. MIXING CHAMBERS
_
8 _
. _ INNER FLAME CONE
g
_
9 _
. _ PREHEAT OXYGEN
e
_
1 _ __OXYGEN CUTTING
0
1 l_ STREAM
1 c __HOSE CONNECTION
.1 _
2 __NEEDLE VALVE
.
CHAPTER 7: FLAME CUTTING QUIZ 6
Name________________________________________________________________Date __________________
Class _________________________Instructor ________________________________________Grade ________
INSTRUCTIONS
Carefully read Chapter 7 in the textbook and answer each question.
IDENTIFICATION
Identify the numbered items on the drawing by writing the letter next to the identifying term in the space provided.
1. j__ HOSE
2. m__ SPRING
3. p__ CYLINDER VALVE
4. g__ WORKING PRESSURE G
5. q__
18. THROUGH
. g__ VALVE
WORKING OF CY GAUGE
PRESSURE
6. f__ SAFETY RELEASE VALVE
19.h . q__ THROUGH VALVE OF CYLINDER TO INPUT OF REGULATOR
7. __ CYLINDER PRESSURE G
20.o . f__ SAFETY RELEASE VALVE
8. __ HIGH-PRESSURE VALVE
21.k . h__ CYLINDER PRESSURE GAUGE
9. __ FLEXIBLE DIAPHRAGM
22. . o__ HIGH-PRESSURE VALVE
10. ___a___ADJUSTING SPRING
k
DES23. . __ FLEXIBLE DIAPHRAGM
24. ___ai___ADJUSTING
11. .___ SPRING DESIGNED FOR PRECISE PRESET
TORCH VALVE
12. ___n___REGULATOR
13. ___c___STEM-TYPE SEAT
MECH
id
25.
14. .___
_________TORCH VALVE
PRECISION
MACHINED Nn
26. .___ ___REGULATOR
15. ___e___BRONZE INLET
27. K.___c___STEM-TYPE SEAT MECHANISM INLET PRESSURE AIDS IN
FILTER
SEALING b
16. ___ ___STAINLESS STEEL
28. .___d___PRECISION MACHINED NOZZLE
DIAPH
e
29.
17. .___
___l ___ADJUSTING
BRONZE INLET FILTER KEEPS OUT DIRT AND FOREIGN
SCREW
MATERIALS
30. .___b___STAINLESS STEEL DIAPHRAGM
31. .___l___ADJUSTING SCREW
