652 Oliver Street

Williamsport, PA. 17701 U.S.A.

SERVICE
Telephone +1 (877) 839-7878 (U.S. and Canada)
Telephone +1 (570) 327-7222 (International)
Fax
Email
+1 (570) 327-7101
[email protected]
INSTRUCTION
www.lycoming.com

DATE: April 8, 2020 Service Instruction No. 1098Q

(Supersedes Service Instruction No. 1098P)
Engineering Aspects are
FAA Approved
SUBJECT: Propeller Flange Bushing Location
MODELS AFFECTED: All Certified Lycoming direct drive engines.
TIME OF COMPLIANCE: At owner’s discretion.
REASON FOR REVISION: Added IO-390-D1A6, -D1B6, -D3A6, -D3B6 engine models to Table 1

NOTICE: Incomplete review of all the information in this document can cause errors. Read the entire
Service Instruction to make sure you have a complete understanding of the requirements.
For correct propeller operation, bushings must be installed in the correct location on the propeller flange.
This Service Instruction is an aide to identify the correct part numbers, dimensions, and respective
installation locations for propeller flange bushings on Lycoming engine models. A checklist is included to
record measurements.
There are two sizes of propeller flange configurations (shown in Figures 1 and 2), each with different
locations for the bushings. Figure 1 shows the smaller propeller flange. Figure 2 shows the larger propeller
flange. The propeller flanges also have different thickness dimensions as shown in Table 1. Table 1 is a list
of engine models, flange thickness for each model, and the propeller flange bushing part numbers that
correspond to each location (A, B, C, D, E, or F); see Figures 1 and 2. As an added reference, Figure 3
shows Dimensions A and B which correspond to bushing part numbers and dimensions shown in Table 2 of
this Service Instruction. For correct indexing, the specified sized bushing in Tables 1 and 2 must be installed
in the respective location on the propeller flange as shown in Figures 1 and 2.
IF THE CORRECT BUSHING IS NOT INSTALLED IN THE SPECIFIED
LOCATION, THE PROPELLER WILL NOT BE INDEXED CORRECTLY AND
EXCESSIVE PROPELLER BLADE STRESSES CAN OCCUR.
To find the correct bushing part number for your propeller flange as follows:
1. Identify whether you have a Type 1 propeller flange (Figure 1) or a Type 2 propeller flange as
follows:
a. Measure from one propeller attaching bushing across the center of the propeller flange to the
opposite bushing.
b. If this measurement is 4-3/8 in. (11.1 cm), you have a Type 1 propeller flange. Use Figure 1 as
your reference for bushing installation locations.
c. If the measurement is 4-3/4 in. (12.0 cm), you have a Type 2 propeller flange. Use Figure 2 as
your reference for bushing installation locations.
ISSUED REVISED PAGE NO. REVISION
MO DAY YEAR MO DAY YEAR
1 of 12 Q
02 07 64 04 08 20
©2019 by Avco Corporation. All Rights Reserved.
Lycoming Engines is a division of Avco Corporation.
 2. Measure and record the features of the crankshaft mounting flange on the checklist at the end of this
Service Instruction.
3. Measure the outside diameter and height of the bushing (Dimensions A and B) in Figure 3. Record
measurements on the checklist at the end of this Service Instruction. Refer to bushing part numbers
that correspond to Dimensions A and B in Table 2. Use a bushing that will give a 0.0005 to 0.0020
in. (0.0127 to 0.0508 mm) tight fit between the bushing and its bore.
4. Refer to Tables 1 and 2 to identify the correct bushing part number by engine model, propeller
flange thickness, and installation location for the corresponding propeller flange in Figure 1 or 2.
5. In Table 1, each bushing location configuration has a reference point (indexed part number)
indicated by a ■.

NOTE: Flanges are viewed from the front of the engine looking aft.
Figure 1 Figure 2
Type 1. Prop. Flange Bushing Location Type 2. Prop. Flange Bushing Location
4-3/8 in. (11.1 cm) diameter 4-3/4 in. (12.0 cm) diameter
NOTE
For O-340-A and O-320 constant speed models incorporating 3/8 in. (9.53 mm) bolts, see the
latest revision of Lycoming Service Bulletin No. 253.

Table 1
Bushing Locations by Engine Model
Flange Bushing Location on
Thickness Fig. Figure
Lycoming Engine Models Type
Ref.
Installation
Bushing P/N
in. mm. Location
O-235-C1B, -C2A, -C2B, -C2C, -F2A, -F2B, -H2C, 0.19 4.8 1 1 A 60814-S
-J2A, -K2A, -K2B, -K2C, -L2A, -L2C, -N2A, B 60814-S
-N2C (Fixed Pitch); C 60814-S
O-235-E2A, -G2A, -P2A (Constant Speed) D 60814-S
E 73757-S ■
F 60814-S

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
2 of 12 Q
02 07 64 04 08 20
 Table 1 (Cont.)
Bushing Locations by Engine Model
Flange Bushing Location on
Thickness Fig. Figure
Lycoming Engine Models Type
Ref.
Installation
in. mm. Bushing P/N
Location
O-235-C1, -C1B (Constant Speed) 0.19 4.8 2 2 A 60814-S ■
B 60814-S
C 60814-S
D 60814-S
E 60814-S
F 60814-S
O-235-C1, -C1B, -C1C, -F1B, -M1 (Fixed Pitch) 0.19 4.8 2 2 A 73757-S ■
B 60814-S
C 60814-S
D 60814-S
E 60814-S
F 60814-S
O-290 Series 0.27 6.8 2 2 A 72067-S ■
B 72067-S
C 72067-S
D 72067-S
E 72067-S
F 72067-S
O-320-A2A, -A2B, -A2C, -A2D, -B2A, -B2B, -B2C, 0.27 6.8 2 2 A 72066-S ■
-D2A, -D2B, -D2C, -D3G, -E2A, -E2B, -E2C, B 72067-S
-E2F -E3D, -E3H; C 72067-S
IO-320-E2A, -E2B; D 72067-S
AEIO-320-E2A, -E2B E 72067-S
F 72067-S
0.38 9.6 2 2 A LW-18921 S ■
B LW-18922-S
C LW-18922-S
D LW-18922-S
E LW-18922-S
F LW-18922-S
O-320-A1A, -A1B, -A3A, -A3B, -A3C, -B1A, -B1B, 0.27 6.8 2 2 A 72065-S ■
-B3A, -B3B, -B3C, -D1A, -D1C, -D1D, -D1F, B 72063-S
-E1A, -E1C, -E1F, -E1J; C 72064-S
O-320-H2AD “76” Series (Constant Speed), -H1CD; D 72063-S
IO-320-D1A, -D1B, -E1A, -E1B; E 72063-S
AEIO-320-D1B, -E1A, -E1B; F 72064-S
AIO-320-A1B, -B1B, -C1B; 0.38 9.6 2 2 A LW-18817-S ■
LIO-320-B1A, -C1A, -D1A B LW-18815-S
C LW-18816-S
D LW-18815-S
E LW-18815-S
F LW-18816-S

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
3 of 12 Q
02 07 64 04 08 20
 Table 1 (Cont.)
Bushing Locations by Engine Model
Flange Bushing Location on
Thickness Fig. Figure
Lycoming Engine Models Type
Ref. Installation
in. mm. Bushing P/N
Location
O-320-D2F, -D2G, -D2J, -E2D, -E2G, -E2H; 0.27 6.8 2 2 A 72065-S ■
IO-320-B2A; B 72063-S
O-320-H2AD “76” Series (Fixed Pitch); C 72063-S
AEIO-320-D2B D 72063-S
E 72063-S
F 72063-S
0.38 9.6 2 2 A LW-18817-S ■
B LW-18815-S
C LW-18815-S
D LW-18815-S
E LW-18815-S
F LW-18815-S
IO-320-B1A, -B1C, -B1D, -C1A, -F1A 0.27 6.8 2 2 A 72065-S ■
B 72064-S
C 72063-S
D 72063-S
E 72064-S
F 72063-S
0.38 9.6 2 2 A LW-18817-S ■
B LW-18816-S
C LW-18815-S
D LW-18815-S
E LW-18816-S
F LW-18815-S
O-360-A1A, -A1AD, -A1B, -A1C, -A1D, -A1F, 0.38 9.6 2 2 A 72062-S
-A1F6, -A1G, -A1G6, -A1G6D, -A1H, -A1K6, B 72062-S
-A1H6, -A1LD, -A2A, -A2D, -A2E, -A2F, -A2G, C 72061-S
-A4D, -A4G, -A4J, -A4JD, -A4K, -A4N, -A4P, D 72062-S
-A5AD, -B1A, -B1B, -B2A, -B2C, -C1A, -C1C, E 72062-S
-C1E, -C1F, -C2A, -C2B, ** -C2C, -C2D, -C2E, F 72060-S ■
-C4F, -C4P, -D2A, -D2B, -D2C, -F1A6, -G1A6; 0.44 11.11 2 2 A 75656-S
O-360-E1AD, -E1A6D “76” Series; B 75656-S
IO-360-A1A, -A1B, -A1B6, -A1B6D, -A1C, -A1C6,
C 72155-S
-A1D, -A1D6, -A1D6D, -A2A, -A2B, -A2C, -B1A,
D 75656-S
-B1B, -B1BD, -B1D, -B1E, -B1F, B1F6, -B1G6,
E 75656-S
-B2E, -B2F6, -C1A, -C1B, -C1C, -C1CD, -C1C6,
-C1D6, -C1E, -C1E6, -C1E6D, -C1F, -C1G6, F 75657-S ■
-D1A, -E1A, -F1A, -L2A, -M1A, -M1B, -N1A;
-P1A
AIO-360-A1A, -A1B, -B1B, -A2A, -A2B;
LIO-360-B1G6
AEIO-360-A1A, -A1B, -A1B6, -A1C, -A1D, -A1E,
-A1E6, -A2A, -A2B, -A2C, -B1B, -B1D, -B1F,
-B1F6, -B2F6, -B1G6, -H1A, -H1B;
** - Not used if wooden propeller is installed
ISSUED REVISED PAGE NO. REVISION
MO DAY YEAR MO DAY YEAR S.I. 1098
4 of 12 Q
02 07 64 04 08 20
 Table 1 (Cont.)
Bushing Locations by Engine Model
Flange Bushing Location on
Thickness Fig. Figure
Lycoming Engine Models Type
Ref. Installation
in. mm. Bushing P/N
Location
TIO-360-E1A6D “76” Series; 0.38 9.6 2 2 A 72062-S
TIO-360-A1B, -A1A6D, -B1A6D, -C1A6D, B 72062-S
-F1A6D; C 72061-S
TO-360-C1A6D; D 72062-S
VO-360-A1A, -A1B, -B1A, -G1A; E 72062-S
IVO-360-A1A; F 72060-S ■
HO-360-A1A, -B1A, -B1B, -C1A; 0.44 11.11 2 2 A 75656-S
HIO-360-A1A, -B1A, -B1B, -C1A, -C1B, -D1A, B 75656-S
-G1A; C 72155-S
LO-360-A1G6D “76” Series; D 75656-S
LO-360-A1H6, -A2D; E 75656-S
LHIO-360-C1A F 75657-S ■
†O-360-C1G; 0.38 9.6 2 2 A 72061-S
O-360-A1P, -A3D6D; B 72062-S
IO-360-C1G, -A3B6, -A3B6D, -J1A6D C 72062-S
D 72061-S
E 72062-S
F 72074-S ■
0.44 11.11 2 2 A 72155-S
B 75656-S
C 75656-S
D 72155-S
E 75656-S
F 79024-S ■
O-360-A3A, -A3AD, -A4A, -A4AD, -A4M; 0.38 9.6 2 2 A 74249-S
IO-360-B2F, -B4A; B 74249-S
AEIO-360-B2F, -B4A C 74249-S
D 74249-S
E 74249-S
F 74248-S ■
0.44 11.11 2 2 A LW-18819-S
B LW-18819-S
C LW-18819-S
D LW-18819-S
E LW-18819-S
F LW-18818-S ■
O-360-J2A 0.44 11.11 2 2 A 01K22155-S
B 01K22155-S
C 01K22155-S
D 01K22155-S
E 01K22155-S
F 01K22156-S ■
† - Re-indexed propeller bushings. Refer to the latest revision of Lycoming Service Instruction No. 1452.

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
5 of 12 Q
02 07 64 04 08 20
 Table 1 (Cont.)
Bushing Locations by Engine Model
Flange Bushing Location on
Thickness Fig. Figure
Lycoming Engine Models Type
Ref. Installation
in. mm. Bushing P/N
Location
O-360-C2C (Wooden Prop.) (Long Bushings) 0.38 9.6 2 2 A 75561-S
B 75561-S
C 75561-S
D 75561-S
E 75561-S
F 75560-S ■
0.44 11.11 2 2 A 01K21700-S
B 01K21700-S
C 01K21700-S
D 01K21700-S
E 01K21700-S
F 01K21699-S ■
IO-360-K2A 0.44 11.11 2 2 A 75656-S
B 75656-S
C 75656-S
D 75656-S
E 75656-S
F 79024-S ■
HIO-360-C1A, -C1B, -E1AD, -E1BD, 0.38 9.6 2 2 A 72061-S
Enstrom (Long Bushings) B 75561-S
C 75561-S
D 72061-S
E 75561-S
F 75560-S ■
0.44 11.11 2 2 A 72155-S
B 01K21700-S
C 01K21700-S
D 72155-S
E 01K21700-S
F 01K21699-S ■
HIO-360-F1AD 0.44 11.11 2 2 A 72061-S
Enstrom (Long Bushings) B 75561-S
C 75561-S
D 72061-S
E 75561-S
F 75560-S ■
LIO-360-M1A 0.44 11.11 2 2 A 75656-S
B 75656-S
C 72155-S
D 75656-S
E 75656-S
F 75657-S ■

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
6 of 12 Q
02 07 64 04 08 20
 Table 1 (Cont.)
Bushing Locations by Engine Model
Flange
Bushing Location on Figure
Thickness Fig.
Lycoming Engine Models Type
Ref. Installation
Bushing P/N
in. mm. Location
LO-360-E1AD, -E1A6D “76” Series; 0.38 9.6 2 2 A 72062-S
LIO-360-C1E6, -C1E6D; B 72061-S
LTO-360-E1A6D “76”Series C 72062-S
D 72062-S
E 72061-S
F 72074-S ■
0.44 11.11 2 2 A 75656-S
B 72155-S
C 75656-S
D 75656-S
E 72155-S
F 79024-S ■
TIO-360-A3B6 0.38 9.6 2 2 A 72062-S
B 72062-S
C 72062-S
D 72062-S
E 72061-S
F 72074-S ■
0.44 11.11 2 2 A 75656-S
B 75656-S
C 75656-S
D 75656-S
E 72155-S
F 79024-S ■
IO-390-A1A6, -A1B6, -C1A6, -C1B6, -D1A6, 0.44 11.11 2 2 A 72155-S
-D1B6 B 75656-S
AEIO-390-A1A6, -A1B6 C 75656-S
D 72155-S
E 75656-S
F 79024-S ■
IO-390-A3A6, -A3B6, -C3A6, -C3B6, -D3A6, 0.44 11.11 2 2 A 75656-S
-D3B6 B 75656-S
AEIO-390-A3A6, -A3B6 C 72155-S
D 75656-S
E 75656-S
F 75657-S ■
HIO-390-A1A 0.44 11.11 2 2 A 72061-S
B 75561-S
C 75561-S
D 72061-S
E 75561-S
F 75560-S ■

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
7 of 12 Q
02 07 64 04 08 20
 Table 1 (Cont.)
Bushing Locations by Engine Model
Flange
Bushing Location on Figure
Thickness Fig.
Lycoming Engine Models Type
Ref. Installation
Bushing P/N
in. mm. Location
O-540-A1A,-A1A5,-A1B5,-A1C5,-A1D,-A1D5, 0.38 9.6 2 2 A 72062-S
-A3D5, -A4A5, -A4B5, -A4D5, -A4E5, -B1A5, B 72062-S
-B1B5, -B2A5, -B2B5, -B2C5, -B4A5, -B4B5, - C 72061-S
E4A5, -E4B5, -E4C5, -F1A5, -F1B5, -G1A5, - D 72062-S
G2A5, -H2A5, -H1B5D, -H2B5D, -J1A5D,- E 72062-S
J2A5D, -J3A5, -J3A5D, -J3C5D, -L3C5D; F 72060-S ■
IO-540-B1C5 (Wide Cyl. Flange), -C1B5, 0.44 11.11 2 2 A 75656-S
-C1C5, -C4B5, -C4B5D, -C4C5, -C4D5, B 75656-S
-C4D5D, -D4A5, -D4B5, -D4C5, -J4A5
C 72155-S
(Standard Cyl. Flange), -T4A5D, -T4B5,
D 75656-S
-T4B5D, -T4C5D, -V4A5, -V4A5D, -W1A5,
-W1A5D, -W3A5D; E 75656-S
IO-540-K1A5, -K1A5D, -K1B5, -K1D5, -K1E5, F 75657-S ■
-K1E5D, -K1G5, -K1G5D, -K1H5, -K1K5,
-L1A5, -L1A5D, -L1C5, -M1A5D, -M1B5,
-M1B5D, -AA1B5, -AB1A5, -AE1A5, -AF1A5
AEIO-540-D4A5, -D4B5, -D4D5, -L1B5,
-L1B5D;
TIO-540-A1A, -A1B, -AA1AD, -AB1AD,
-AB1BD, -AF1A, -AF1B, -AG1A, -AH1A,
-AK1A, -C1A, -C1AD, -E1A, -G1A, -H1A
O-540-A2B; 0.38 9.6 2 2 A 72062-S
IO-540-C2C, -G1C5, -J1A5 (Wide Cyl. Flange), B 72061-S
-K1C5 C 72062-S
D 72062-S
E 72061-S
F 72074-S ■
0.44 11.11 2 2 A 75656-S
B 72155-S
C 75656-S
D 75656-S
E 72155-S
F 79024-S ■
IO-540-A1A5, -B1A5, -B1C5 (Standard Cyl. 0.38 9.6 2 2 A 72062-S
Flange), -E1A5, -E1B5, -G1A5, -G1B5, B 72062-S
-G1D5, -G1E5, -G1F5, -P1A5 C 72062-S
D 72062-S
E 72061-S
F 72074-S ■
0.44 11.11 2 2 A 75656-S
B 75656-S
C 75656-S
D 75656-S
E 72155-S
F 79024-S ■

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
8 of 12 Q
02 07 64 04 08 20
 Table 1 (Cont.)
Bushing Locations by Engine Model
Flange
Bushing Location on Figure
Thickness Fig.
Lycoming Engine Models Type
Ref. Installation
Bushing P/N
in. mm. Location
IO-540-AG1A5, -K1F5D, -K1J5D, -M1A5, -M1C5; 0.44 11.11 2 2 A 75656-S
TIO-540-A2A, -A2B, -A2C, -F2BD, -J2B, -J2BD, B 75656-S
-N2BD, -R2AD, -V2AD; C 72155-S
LTIO-540-F2BD, -J2B, -J2BD, -N2BD, -R2AD, D 75656-S
-V2AD E 75656-S
TEO-540-A1A, -C1A F 79024-S ■
IO-540-AA1A5, -K1C5, -K1F5, -K1J5, -S1A5; 0.44 11.11 2 2 A 75656-S
TIO-540-U2A, -W2A, -AE2A; B 75656-S
LTIO-540-U2A C 75656-S
D 75656-S
E 72155-S
F 79024-S ■
IO-540-M2A5D 0.44 11.11 2 2 A 72155-S
B 72155-S
C 72155-S
D 72155-S
E 72155-S
F 75657-S ■
IO-540-K2A5 0.44 11.11 2 2 A 72156-S
B 72156-S
C 75656-S
D 72156-S
E 72156-S
F 75657-S ■
IO-540-N1A5, -N1A5D, -R1A5, -R1A5D 0.44 11.11 2 2 A 72155-S
B 75656-S
C 75656-S
D 72155-S
E 75656-S
F 79024-S ■
IO-540-AC1A5; 0.44 11.11 2 2 A 75656-S
TIO-540-AJ1A B 75656-S
C 75656-S
D 75656-S
E 75656-S
F 75657-S ■
TIO-540-S1AD 0.44 11.11 2 2 A 75656-S
B 72155-S
C 75656-S
D 75656-S
E 72155-S
F 79024-S ■

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
9 of 12 Q
02 07 64 04 08 20
 Table 1 (Cont.)
Bushing Locations by Engine Model
Flange
Bushing Location on Figure
Thickness Fig.
Lycoming Engine Models Type
Ref. Installation
mm. Bushing P/N
in. Location
TIO-541-E1A4, -E1B4, -E1C4 0.44 11.11 2 2 A 72156-S
B 72156-S
C 72155-S
D 72156-S
E 72156-S
F 73811-S ■
TIO-541-A1A; 0.44 11.11 2 2 A 75656-S
AEIO-580-B1A; B 75656-S
IO-580-B1A C 72155-S
D 75656-S
E 75656-S
F 75657-S ■
IO-720-A1A, -A1B, -B1B, -B1BD, -C1B, -D1B, 0.44 11.11 2 2 A 72156-S
-D1BD, -D1C, -D1CD B 72156-S
C 72156-S
D 72156-S
E 72155-S
F 73811-S ■
** - Not used if wooden propeller is installed
† - Re-indexed propeller bushings. Refer to the latest edition of Lycoming Service Instruction No. 1452.

Table 2
Bushing Part Numbers and Dimension
Prop. Bolt Dimension Dimension
Bushing Thread Size A B
Part No.
in. mm in. Mm in. mm
60814-S 3/8 9.53 0.6255-0.6260 15.8877-15.9004 0.95 24.13
72060-S 1/2 12.7 0.7818-0.7823 19.8577-19.8704 0.59 14.99
72061-S 1/2 12.7 0.7505-0.7510 19.0627-19.0754 0.59 14.99
72062-S 1/2 12.7 0.7505-0.7510 19.0627-19.0754 0.78 19.81
72063-S 7/16 11.11 0.6255-0.6260 15.8877-15.9004 0.90 22.86
72064-S 7/16 11.11 0.6255-0.6260 15.8877-15.9004 0.48 12.19
72065-S 7/16 11.11 0.6725-0.6730 17.0815-17.0942 0.90 22.86
72066-S 3/8 9.53 0.6725-0.6730 17.0815-17.0942 1.02 25.91
72067-S 3/8 9.53 0.6255-0.6260 15.8877-15.9004 1.02 25.91
72074-S 1/2 12.7 0.7818-0.7823 19.8577-19.8704 0.78 19.81
72155-S 1/2 12.7 0.7505-0.7510 19.0627-19.0754 0.65 16.51

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
10 of 12 Q
02 07 64 04 08 20
 Table 2 (Cont.)
Bushing Part Numbers and Dimension
Prop. Bolt Dimension Dimension
Bushing
Thread Size A B
Part No.
in. mm in. Mm in. mm
72156-S 1/2 12.7 0.7505-0.7510 19.0627-19.0754 0.97 24.64
73757-S 3/8 9.53 0.6725-0.6730 17.0815-17.0942 0.95 24.13
73811-S 1/2 12.7 0.7818-0.7823 19.8577-19.8704 0.97 24.64
74248-S 1/2 12.7 0.7818-0.7823 19.8577-19.8704 0.98 24.89
74249-S 1/2 12.7 0.7505-0.7510 19.0627-19.0754 0.98 24.89
75560-S 1/2 12.7 0.7818-0.7823 19.8577-19.8704 1.63 41.40
75561-S 1/2 12.7 0.7505-0.7510 19.0627-19.0754 1.63 41.40
75656-S 1/2 12.7 0.7505-0.7510 19.0627-19.0754 0.84 21.33
75657-S 1/2 12.7 0.7818-0.7823 19.8577-19.8704 0.65 16.51
79024-S 1/2 12.7 0.7818-0.7823 19.8577-19.8704 0.84 21.33
LW-18815-S 7/16 11.11 0.6255-0.6260 15.8877-15.9004 1.01 25.65
LW-18816-S 7/16 11.11 0.6255-0.6260 15.8877-15.9004 0.59 14.99
LW-18817-S 7/16 11.11 0.6725-0.6730 17.0815-17.0942 1.01 25.65
LW-18818-S 1/2 12.7 0.7818-0.7823 19.8577-19.8704 1.04 26.41
LW-18819-S 1/2 12.7 0.7505-0.7510 19.0627-19.0754 1.04 26.41
LW-18921-S 3/8 9.53 0.6725-0.6730 17.0815-17.0942 1.13 28.70
LW-18922-S 3/8 9.53 0.6255-0.6260 15.8877-15.9004 1.13 28.70
01K21699-S 1/2 12.7 0.7818-0.7823 19.8577-19.8704 1.69 42.92
01K21700-S 1/2 12.7 0.7505-0.7510 19.0627-19.0754 1.69 42.92
01K22155-S 3/8 9.53 0.7505-0.7510 19.0627-19.0754 1.19 30.22
01K22156-S 3/8 9.53 0.7818-0.7823 19.8577-19.8704 1.19 30.22
NOTICE: Tool No. ST-115 is used to remove and replace all propeller flange bushings.

NOTICE: Service replacements for all flange bushings are available in

the following oversizes.

P05 P10 P15 P20

.005 in .010 in. .015 in. .020 in.

Figure 3
Bushing Dimensions A and B

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
11 of 12 Q
02 07 64 04 08 20
 Crankshaft Mounting Flange Measurements Checklist
Engine Model Date Crankshaft Flange P/N

Parameter to Measure Measurement Corrective Action

Thickness of the crankshaft

mounting flange

Diameter of each bushing

hole on the crankshaft
mounting flange

Depth of each bushing hole on

the crankshaft mounting
flange (could be equal or not
equal to the thickness of the
flange)

Propeller Flange Bushing Measurements Checklist

Outside Diameter of
Height of the Bushing
Propeller the Bushing
Installation (Dimension B
Flange (Dimension A Corrective Action
Location Figure 3)
Bushing P/N Figure 3)
Refer to Table 2
Refer to Table 2
A

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR S.I. 1098
12 of 12 Q
02 07 64 04 08 20