4D-F9

Suitable for ages over 14

Quadcopter operating instructions

English

In order to meet the requirements of the aeronautical radio station's

electromagnetic environment (various of aero models and UAV are not
allowed to fly within the range of 10 km on each side of center line and
20km on both ends of the airport runway and in the) and civil aviation
routes and airlines. Using various models and drones in the no-fly zone
issued by the relevant state departments is prohibited.
 Warning
1. The packaging and instructions contain important information and should be kept.
2. With this aircraft, you are responsible for ensuring that no harm will be caused to the personal and
property of others.
3. Commissioning and installing of aircraft must be strictly in accordance with the operating
instructions, and attention shall be paid to the distance between the aircraft and the user or other
people shall be 2 to 3m to prevent the aircraft from bumping into the head, face and body of
people and causing injury in flying and landing, etc.
4. Our company and distributors are not responsible for any loss and damage, as well as injury to
people caused by improper use or operation.
5. Children should be guided by adults when operating the aircraft. This product is prohibited to be
operated by children under 14 years old.
6. Please follow the instructions or packaging instructions to install and use correctly, and some parts
should be assembled by adults.
7. The product contains small parts, please place it out of the reach of children to prevent the risk of
accidental eating or suffocation.
8. It is strictly forbidden to play on the road or in the place where water is accumulated to avoid
accidents.
9. Please put away the packing materials in time to avoid harm to children.
10. Do not disassemble or modify the aircraft. Disassembly or modification may cause malfunction to
the aircraft.
11. The charging cable needs to be inserted into the designated power supply 5V 2A that is the
same as the product label.
12. The use of other charging cables will cause damage to the battery and may cause unexpected
dangers.
13. The charging cable is not a toy.
14. When charging the rechargeable battery, it must be under the supervision of an adult. When
charging, it must be far away from flammable materials. During charging, the guardian should not
leave the monitoring range.
15. Please do not short circuit or squeeze the battery to avoid explosion.
16. Do not mix different types of lithium batteries.
17. The aircraft uses a rechargeable lithium battery, which needs to be pulled out for charging.
18. Do not short-circuit, decompose or throw the battery into fire; do not put the battery in a place
with high temperature and heat (such as in fire or near electric heating device).
19. The aircraft should be used as far away from other electrical equipment and magnetic objects as
possible, they may cause mutual interference.
20. Please keep a safe distance from the high-speed rotating propeller to avoid the risk of scalp or
cut
21. The motor is a hot part; please do not touch it to avoid burns.
22. LED has laser radiation; please do not give direct light beam to others.
23. Do not use the model near your ears! Misuse may cause hearing damage.
24. The USB charging cable must use the data cable provided by our company to charge the battery,
otherwise it will cause serious damage to the battery and will lead to unexpected danger.
25. To meet the magnetic environment requirements of aeronautical radio stations. During the radio
control order issued by the relevant state departments, the model remote control should be
stopped within the city area as required.
26. Turn off the switch and unplug the battery when the battery of the aircraft is used up, and charge
after 30 minutes of rest, otherwise the battery will be easily damaged.

01
1. List of accessories included:

Aircraft ×1 USB charging Fan blade ×2 Lithium battery ×1 Screwdriver ×1 Operating

cable ×1 Instructions ×1

2. Name of each part of aircraft:

Fan blade clip Battery

Motor
Shell

Fan blade

LED lights

Camera Bottom camera

3. Wind blade installation diagram:

3.1 Unscrew the screw and remove the fan blade.

A1/A2 Note: The fan blade is printed with letters of
A1/A2
A1, A2, B1, and B2, in which, A1 = A2, B1 =
B2, please install it correctly according to the
diagram, otherwise it cannot take off.

02
4. Unfolding steps of the aircraft: (It is in the storage state when it leaves the factory)
1. Unfold the aircraft according to the steps

1 2 3

B1/B2 A1/A2

A1/A2 B1/B2
5 4

5. Lithium battery charging instructions:

1 2

5.1 Buckle the battery lock of the aircraft. 5.2 Remove the battery.

3 Laptop Desktop PC Mobile power USB adapter USB power

socket

5.3 Charging: Insert the USB port of the USB charging cable into the computer USB port (or use
5V 2A power adapter), and connect the other end of the USB charging cable to the battery
socket. When charging, the red indicator on the module battery is on, and when the battery is
fully charged, the red indicator light goes out, which means that the charging is complete.

Warning
It must be charged with the aircraft charging cable provided by the factory, and
other charging cables cannot be used. Be sure to remember to avoid accidents.

03
6. Name of each part of the remote control:

Description of remote
control indicator:

Press the GPS One-key Headless

emergency return mode

Fine adjustment (press and pause button at

hold)/speed gear the same time

Power Indicator Photo / Video (long

press)
Left stick Right stick

Power switch (long press) GPS switch (long

press)
Horizontal calibration (short
press) Geomagnetism Headless mode
(compass) calibration (long One-key return
press for 3s)
One-key take-off / one-key
landing
Normal/GPS button: Press and hold this button for 3s after frequency matching to switch between
normal mode and GPS mode (It is by default GPS mode after starting up, GPS indicator will be on,
and when it enters normal mode, the indicator will be off).
Headless mode button: Press this button once to enter the headless mode, the headless light will
be on; press it again to exit the headless mode, and the headless light will be off.
Return button: Press this button once to return home, and the return light will be on. Press again to
cancel the returning, and the return light will be off.

7. Remote control battery installation:

Battery installation:
7.1 Press the battery cover button with
a screwdriver and remove the
battery cover at the same time.
7.2 According to the polarity
instructions on the battery
Battery cover
compartment, remove the battery
cover on the back and insert a 4X
“AAA” battery (not included).
Note
1. The positive and negative poles and the positive and
AAA battery negative poles of the battery box must be identified when
inserting the battery, and error is not allowed.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries.

Instructions in charging:
● Do not put the charged battery in a place with high temperature and heat, such as an
open flame or an electric heating device, otherwise damage or explosion may occur.
● Do not hit or beat the surface of hard objects with the battery. Warning
● Do not disassemble the battery. When the aircraft is not in flying, disconnect the

● Do not immerse the battery in water, and please store the

battery plug from the power connector of the aircraft
circuit board to prevent the battery from being
damaged.
battery in a dry place.
● Do not leave battery alone when charging.

04
8. APP download and installation instructions:

8.1 Download and install the software

For Google mobile phone, after scanning the code, choose to open and download in the browser

Download on the
4DRC PRO

Google system: Please Apple system: Please scan

scan this QR code to install this QR code to install
8.2 Link description
① Turn on the power of aircraft, enter the (Settings) option (of mobile phone or IPAD), and open the
wireless network; find the device name of "4DRC_6K_GPS " in the wireless network search list and
connect; after connection, exit the setting option.
② Open the software icon "4DRC PRO " in mobile phone to enter the control interface. (Try to stay away
from other signal source environments when flying).

Open "4DRC PRO " software Select Go to enter the

control interface

Select and click "More Features" Enter the function menu

9. APP control interface function introduction:

Satellite signal
Flight status
More features
Return

Takeoff / landing
One-key return
Unlock

Map

Flight distance

05
 Multipoint flight
3D stereo Follow
Reverse the lens Orbit
Unlock
Find the plane
Gesture photo
Speed gear
Music
Touch joystick
Lens switching

Novice mode
Flight distance,
default 30m, (20m-2000m)

Flight altitude,
default 30m, (10m-120m)

Note: After being proficient in flight operation, it is necessary to close the novice mode
and set the flight distance and altitude before the aircraft can fly further!

10. Environmental requirements before flight:

Please choose to fly in an open air environment without rain and snow, where the
wind force is less than 3. Please keep away from the crowd, trees, wires, tall
buildings, airports and signal transmission towers. Do not fly in an indoor environment

06
11. Preparation instructions before flight

11.1 Aircraft frequency matching Turn on the power of

the aircraft and place it on a horizontal surface. At
this time, the aircraft placed on the horizontal
surface will automatically enter the frequency
matching state, and the front blue light and the
rear red light will flash.

11.2 Turn on the WiFi function in the mobile device,

select "4DRC_6K_GPS " in the WiFi list, and
open the APP after it connected successfully.

11.3 Turn on the remote control (default mode): long

press the power switch button (step 1), turn on 2
the power and the indicator flashes; push the 2
throttle lever up to the top (step 2) and then to the 3
bottom (step 3), and thus the frequency matching 1
is successful, the UAV lights change from flashing
to being permanently on.

Warning
It must ensure that the power of the aircraft/remote control is sufficient or
it cannot take off!

11.4 Horizontal calibration operation:

Short press the horizontal calibration button on the remote control, the blue light and red light on
the aircraft will flash quickly. When the blue light and red light on the aircraft are always on, it means
that the calibration is completed, and the remote control will emit a beep (Figure 1).
APP application operation: Click "Set more" icon in the APP interface, and follow the text prompt
steps after entering, and it can also be horizontally calibrated (Figure 2).
Note: In calibration, the aircraft must be placed on a horizontal surface to complete the calibration.

07
 Figure 1

Figure 2

11.5 Geomagnetic calibration operation

Figure 3

1. Long press the 2. Horizontal clockwise rotation - pick 3. Clockwise rotation with the tail of the
geomagnetic calibration up the aircraft horizontally, and aircraft upward - pick up the aircraft
button until the front rotate it clockwise until the front with its nose vertically downward,
blue light and the rear blue light is always on and the rear rotate clockwise until the front blue
red light on the aircraft tail red light flashes slowly, and the light and the rear red light of the
flash slowly. remote control beeps once, which aircraft are always on, and the remote
means the level calibration is control emits a beep, which means
completed. the guide calibration is completed.

APP application operation: In entering the interface of "Setting more", according to the
text prompt and operation steps, you can also guide the calibration (Figure 4).

Figure 4

08
11.6 Star search status (In GPS mode by default)
The remote control is in GPS mode and the GPS light is always on, which means that the
GPS is in the state of star searching. When the red tail light of the aircraft flashes quickly, it
means that the star searching succeeded, and the remote controller will emit a beep. The
aircraft can be unlocked at this time (Figure 5).
Note: The first time of star search needs to wait at least a few minutes, and the search
signal reaches about 10 stars before it can take off.

Description of remote
control indicator:

GPS One-key Headless

return mode

Figure 5

11.7 Start/stop (GPS mode)

Push the left and right joysticks on the remote control outward to unlock, (if the star search
is unsuccessful, it cannot be unlocked and started) (Figure 6). At this time, the aircraft can
take off normally. After taking off, all the indicators of the aircraft are always on.
APP operation: Click "One Key Unlock" icon (Figure 7) in APP control interface, the
one-key unlock function can also be achieved.

Figure 6 Figure 7

11.8 One-key take-off and landing

When unlocking is complete, gently press the “One Key Takeoff/Landing” key on the
remote control (Figure 8), the aircraft will automatically rise to a height of about 1 meter to
maintain a stable flight; when you press this function key gently again, the aircraft will
automatically land slowly.
APP operation: Click "one-key take-off" icon (Figure 9) in APP control interface, the
one-key take-off function can also be achieved; during flight, click this icon again, the
aircraft will automatically land slowly.

09
 Figure 8 Figure 9

11.9 Normal mode

The aircraft enters the normal mode

11.10 Start / stop (common mode needs to be turned on for indoor operation)

Figure 10 Figure 11
1. Long press the GPS button on the 2. Push the left and right joysticks on the remote
remote control, GPS indicator of the remote control outward to unlock (Figure 11)
control will enter normal mode (Figure 10)

Figure 12 Figure 13

3. Then push up the left 4. Or press one key take off button
joysticks (Figure 12) to take off (Figure 13)

10
 Before flying, please perform the following steps in the above order: open (refer
Warning to 11.1) → link to WIFI (refer to 11.2) → remote control to start frequency
matching(refer to 11.3) → horizontal calibration (refer to 11.4) → geomagnetic
calibration (refer to 11.5) → Star search status (in GPS mode by default)
(reference 11.6) → start/stop (GPS mode) (reference 11.7) → takeoff and landing
(refer to 11.8) → normal mode(refer to 11.9) → start/stop (it needs to open the
normal mode for indoor operation) (refer to 11.10)

12. Control method:

APP application operation: Enter the APP control interface and click the "more functions"
icon to open the "joystick on/off" icon, you can see the operation joystick on the interface.
The operation method is as follows:

When the left joystick (throttle) is

pushed up, the rotation rate of the main
blade increases and the aircraft rises.
When the left joystick (throttle) is
pushed down, the rotation rate of the
main blade slows down and the aircraft
descends.

When the left joystick (rudder) is

pushed to the left, the aircraft nose
turns to the left. When the left joystick
(rudder) is pushed to the right and the
nose of the aircraft will turn to the right.

When the right joystick (rudder) is

pushed up, the aircraft moves forward.
When the right joystick (rudder) is
pushed down, the aircraft moves
backward.

When the right joystick (rudder) is

pushed to the right, the aircraft
fuselage deviates to the right.
When the right joystick (rudder) is
pushed to the left, the aircraft fuselage
deviates to the left.

11
 When the aircraft is in 1m from the ground, the aircraft will become unstable due to
Warning
the influence of its own blade vortex, which is called "ground effect response". The
lower the height of the aircraft, the greater the effect of the ground effect response.

13. Introduction to the APP application and remote control function operation:
13.1 Headless mode
The front of the aircraft when the code-matching is turned on is by default the front in
headless mode; if it is necessary to adjust the direction, please turn on the code-matching
again, and short press the remote controller "headless mode" function key (Figure 14).
When exiting, please tap gently press this function key again.
Special prompt: Please make sure the aircraft is aligned with the straight line and let
the gyroscope automatically detect the straight line, and the headless mode of straight
line flight can be realized.

Front Front

Left Right Left Right

Rear Rear
Figure 14

13.2 One key return

Press the one-key return button , the aircraft will return to the place above the geomagnet-
ic calibration position (Figure 15). (The aircraft will automatically rise to a safe altitude when it
is flying below the safe altitude) and then land slowly. If there are obstacles during the landing,
press the one-key return button again to turn off the return operation and avoid by the manual
control joystick, pull down the throttle lever to land.
APP operation: Click the "one-key return" icon (Figure 16) in the APP control interface, you
can also return the aircraft; during the return flight, click this icon again to cancel the return.

Figure 15 Figure 16

12
 Runaway return: When the signal of the remote controller is interrupted for
Warning
about 4s, the aircraft will automatically return to the place where there is a
signal and stop. Low battery return: when the aircraft is in low battery electricity,
it will forcefully return to a place that is 20m above the take-off point. The return
flight cannot be cancelled during the low battery return.
13.3 Speed switching
When the aircraft takes off, it is by default in the low-speed mode (3-geared switching);
gently press the remote control by a "beep" sound for low-speed gear, two "beep" sounds for
medium-speed gear, and three "beep" sounds for high-speed gear (Figure 17)".
APP operation: Click the "More Functions" icon (Figure 18) in the APP control interface, and
the flight speed can also be switched (Figure 19).

Figure 29 Figure 30

Figure 18 Figure 19
Figure 17

13.4 Waypoint flight mode

① In GPS mode, click the "More Functions" icon (Figure 20) in the APP control interface to
enter the multi-point flight (Figure 21). At this time, the interface changes from the image
transmission page to the map page. On the map page, click to set the track range of the
segmented waypoints or continuous waypoints (Figure 22). During the setting, if the track
waypoints are too dense, you can click the delete icon to delete all the waypoints (Figure 23).
② After setting of the waypoint, click the send icon (Figure 24), the aircraft will fly to all
waypoints from the initial point to complete the preset flight trajectory. The direction of the
aircraft can be controlled by the joystick during the flight.

3 4

Figure 20 Figure 21 Figure 22

1 1

2 2

3 4 3 4

Figure 23 Figure 24

13
13.5 Orbital flight mode
In GPS mode, click "More Features" icon in the APP control interface (Figure 25) to enter the
orbit flight mode (Figure 26), the aircraft will automatically orbit in a radius (Figure 27), and
the radius can be adjusted on the APP (Figure 28). At this time, push the right direction
joystick to fly left or right (Figure 29) at the default speed, the orbital speed can be adjusted.
Push the right direction joystick front or rear, the orbit radius can be adjusted, and when the
orbit button is pressed again, the orbit flight will end (Figure 30).

Figure 25 Figure 26 Figure 27

Figure 28 Figure 29 Figure 30

13.6 GPS follow mode

In GPS mode, click the “More Functions” icon (Figure 31) in the APP control interface to
enter the follow (Figure 32). The aircraft will use the distance from the current position to the
operator (mobile phone or IPAD) device as a reference, and move by tracking changes in the
location of mobile devices. In following, lightly press the red icon to cancel the following.

Figure 31 Figure 32

13.7 Gesture recognition

When facing the camera's front lens, click the gesture photo button on the APP, and use any
of the following gestures to trigger the aircraft's photo or camera function.
Special Tip: Please face the lens with the front being at a position about 2-3M away and
in a better light and background environment to perform the gesture recognition.

14
 Yeah gesture photo
In about 3m front of the aircraft lens, make Yeah gesture with one hand in
horizontal position; after the aircraft successfully recognizes the gesture, count
down 3 seconds and take photos.
Palm gesture video-recording
In about 3m front of the aircraft lens, put five fingers together and lift one hand to
horizontal position; after the aircraft successfully recognizes the gesture, it will
start recording. The recording will end when the gesture is re-recognized (the time
difference between the two recognitions shall be greater than 3s).
13.8 MV interface
Click the "filter interface" icon (Figure 33) in the APP control interface, after entering the
filter interface, you can choose to match your favorite filter effect, click the recording icon to
start recording (Figure 34). After the recording is completed, the synthesized short video or
picture will be saved to the media library (Figure 35).
Tips: During the recording process, you can rotate the screen or switch the filter effect,
and you can also turn the joystick on / off to control the direction and altitude of the aircraft.

Figure 33 Figure 34 Figure 35

14. FAQ and solving guidelines:

Question Reason Solution

The aircraft indicator flashes 1. Move the aircraft to an open place and
1. Geomagnetic anomaly
search for stars again
without any response 2. The aircraft has insufficient power
2. Charge the battery
1. Charge the battery
1. Low battery 2.1 Replace the blade
The blades of the aircraft rotate 2.1 Blade deformation
but cannot fly 2.2 The fan blades are printed with letters
2.2 Installation error of AB A and B. For fan blade A or B, replace
propeller the one that is broken
The aircraft vibrates badly Blade deformation Replace the blade

After the impact, start the aircraft 1. Blade deformation 1. Replace the blade
again and it fly uncontrollably 2. Defective motor 2. Replace the motor
After leaving the aircraft for 5-10 seconds,
After the impact, start the aircraft The three-axis acceleration or by the horizontal calibration, it will be ok.
again and it fly uncontrollably sensor loses its balance due to For the steps, please refer to the manual,
impact 11.4 horizontal calibration operation.

15