Metal (Oxide) Film

Fusing Resistors, ERQH, C

Metal (Oxide) Film Fusing Resistors

Type: ERQH
(Flame retardant hermetic type)
Type: ERQC
(Flameproof bath-tub type, Axial leads)

■ Features
● Accurate fusing characteristics
● Flameproof construction in a ceramic tube or case
● Hot spot temperature control
The temperature of the resistor surface will not exceed 600 °C (1112 °F)
● Uniform quality, consistent performance and reliability
● High dielectric withstanding voltage
Resistor can withstand up to 1000 V

■ Construction
Flame-retardant, hermetically sealed

ERQ-12H type
Metal (oxide) film Lead wire

Spiraling turns Marking

Ceramic tube

Ceramic core

Fusing glass

End cap
Flame-proof epoxy resin

Sealing washer

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006

– ER109 –
 Metal (Oxide) Film
Fusing Resistors, ERQH, C

■ Explanation of Part Numbers

1 2 3 4 5 6 7 8 9 10 11 12

E R Q 2 C J 1 0 1

Product Code Power Rating Special Feature Resistance Resistance Value Suffix for Packaging and/or
Metal (Oxide) Film at 70°C amb. Hermetic Tolerance The first two digits are Cut & Formed Leads
H
Fusing Resistors 12 0.5 W (0.5 W) J ± 5% significant figures of Nil Std.bulk packing
1 1W Bath-tub K ±10 % resistance and the third V Axial taped & box
C one denotes number of
2 2W Axial leads P P type cut & formed
zeros following.
3 3W P···S type cut &
Decimal point is P···S
expressed by R as 1.5= formed
1R5.

The above example shows a standard bath-tub type Metal (Oxide) Film Fusing Resistors, 2 W power rating, resistance value of 100 액, tolerance of
5 %, and package of standard bulk packing.

■ Ratings
Power Dielectric Resistance
Maximum Resistance Standard Marking T.C.R. Mass
Rating With- Range (액)
Type Overload Tolerance Resistance Method [҂10-6/°C (Weight)
70 °C standing
Voltage (%) Values on Body (ppm/°C)] [g/pc.]
(W) Voltage(V)
min. max.
K (±10) 0.22 0.82 E12
ERQ12H 0.5 3 times of RCWV (1) AC 1000 0.73
J (± 5) 1 3.9 k E24
K (±10) 0.33 0.82 E12
ERQ1C 1 AC 1000 1.1
J (± 5) 1 1 k E24
Stamp ±500
2.5 times of K (±10) 0.33 0.82 E12
ERQ2C 2 AC 1000 2
RCWV J (± 5) 1 1 k E24
K (±10) 0.33 0.82 E12
ERQ3C 5 AC 1000 5.1
J (± 5) 1 3.3 k E24
(1) Rated Continuous Working Voltage (RCWV) shall be determined from RCWV=앀Power Rating҂Resistance Value

Maximum Open Circuit Voltage

Referring to the maximum value of the voltage applied between terminals of the resistor when the resistor is
opened in an electric circuit, it is defined by type and resistance.
Please stay within the specified voltage. (Please refer to ER114 page)

Power Derating Curve 120

–30 °C 70 °C
For resistors operated in ambient temperatures above 100
Rated Load (%)

70 °C, power rating shall be derated in accordance 80

with the figure on the right. 60
C type
40
H type
20
150 °C
0
–60 –40 –20 0 20 40 60 80 100 120 140 160 180 200 220
Ambient Temperature (°C)

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006

– ER110 –
 Metal (Oxide) Film
Fusing Resistors, ERQH, C

■ Explanation of marking

Type 12H Black stamp Type C Red stamp

Symbol Rated power Manufacturing number Rated power, resistance value and Tolerance
1/2W

1 0 8
16액J 3.3액J
712 Q712
Symbol
Tolerance

Resistance value Date code (Year,Month,Week) Code for fuse resistors Date code (Year,Month,Week)

Type ERQ12H
+3
13 –2 (mm)
■ Dimensions in mm (not to scale) fD

Dimensions (mm) fd
Type
L fD k fd A l L l
±1.5 ±1.0 ±3.0 ±0.05
ERQ12H 12.0 5.3 28.5 0.65 —

ERQ1C 13.0±1.0 — 25.0±4.0 0.65±0.05 5.5±1.0 Type ERQC

ERQ2C 18.0±1.0 — 25.0±4.0 0.80±0.05 6.4±1.0 fd

A
ERQ3C 22.0±1.0 — 32.0±4.0 0.80±0.05 9.5±1.0 l L l A

■ Cut & Formed Type

Type “P”
S
L
fD
h1
h2

f0.65±0.05
3 max. 0.8
1.2±0.2

Unit: mm

Part No. L fD S h1 h2
ERQ12H첸첸첸첸P 12.0±1.5 f5.3±1.0 17.5±1.5 5.85±1.50 4.0±1.0

Type “P···S”
S A
A

L
h1
h2

fd
W2
3 max.
W1

Unit: mm
Part No. L S fd A h1 h2 W1 W2
ERQ1C첸P첸첸첸S (1 W) 13.0±1.0 20.0±2.0 0.65±0.10 5.5±1.0 6.0±1.5 4.0±1.0 1.2±0.2 0.8
±1.0 ±2.0 ±0.10 ±1.0 ±1.5 ±1.0
ERQ2C첸P첸첸첸S (2 W) 18.0 25.0 0.80 6.4 5.8 4.0 1.4±0.2 1

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006

– ER111 –
 Metal (Oxide) Film
Fusing Resistors, ERQH, C

■ Axial Taping Specifications

Type ERQ12H

52.0±1.0

10.0±0.5
+3
l1 13 –2 l2

+3
l1 13 –2 Standard quantity

D/2

95±2
(per box) 1000 pcs.

D
6.0±1.0
75 +2 325±3
| l1-l2 | < 2.0 –1

All dimensions are in millimeters

■ Packaging Methods
Please contact the factory for packaging methods. (Type ERQC)

■ Performance Specifications

Characteristics Specifications Test Methods

No specimens which burn with The test fl ame is applied for 15 seconds and
flaming combustion for more than removed for 15 seconds.
Flame-Retardancy
10 seconds after each application The test shall be repeated until resistor has been
of the test flame. subjected to 5 applications of the test flame.

When resistors are tested using the

specified circuit, the resistors shall
Tested on individual specified circuit, using stable
Fusing Characteristics meet the re quire ments spec i fi ed
power supply.
respectively.
(Refer to page ER113)

When resistors are tested using the

specified circuit, the resistors shall
Maximum open
meet the re quire ments specifi ed Tested on individual specified circuit.
circuit voltage
respectively.
(Refer to page ER114)

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006

– ER112 –
 Metal (Oxide) Film
Fusing Resistors, ERQH, C

■ Fusing characteristics for ERQH, C type (unit : sec)

Multiple of the power rating (times)
ERQ12H type
10 12 16 20 25 30 40
0.22 to 0.82 (액) < 30 < 25 < 10
1.0 to 4.3 (액) < 45 < 25 < 20 < 10
4.7 to 16 (액) < 180 < 90 < 45 < 25 < 20 < 10
Resistance value 18 to 47 (액) < 150 < 120 < 60 < 45 < 15 < 10 < 7
51 to 200 (액) < 45 < 25 < 10
220 to 620 (액) < 45 < 30 < 20 < 10
680 to 3.9 k (액) < 180 < 90 < 45 < 25

(unit : sec)
Multiple of the power rating (times)
ERQ1C type
10 12 16 20 25 30
0.33 to 0.91 (액) < 300 < 180 < 40 < 20 < 10
1.0 to 3.9 (액) < 90 < 45 < 15 < 7 < 7
4.3 to 16 (액) < 90 < 60 < 30 < 10 < 7 < 7
Resistance value 18 to 47 (액) < 60 < 30 < 15 < 10 < 7 < 7
51 to 180 (액) < 90 < 20 < 15 < 10
200 to 620 (액) < 60 < 20 < 7 < 7
680 to 1 k (액) < 90 < 60 < 10 < 7 < 7

(unit : sec)
Multiple of the power rating (times)
ERQ2C type
10 12 16 20 25 30
0.33 to 0.91 (액) < 90 < 30 < 15 < 7
1.0 to 3.9 (액) < 90 < 45 < 20 < 15 < 7
4.3 to 30 (액) < 45 < 30 < 10 < 7 < 7
Resistance value 33 to 47 (액) < 45 < 30 < 20 < 10 < 7 < 7
51 to 180 (액) < 120 < 60 < 20 < 10 < 7
200 to 620 (액) < 90 < 30 < 10 < 7 < 7
680 to 1 k (액) < 60 < 30 < 20 < 10 < 7 < 7

(unit : sec)
Multiple of the power rating (times)
ERQ3C type
10 12 16 20 25 30
0.33 to 0.91 (액) < 240 < 90 < 45 < 20
1.0 to 3.9 (액) < 240 < 90 < 20 < 15
4.3 to 20 (액) < 300 < 120 < 60 < 20 < 15 < 15
Resistance value
22 to 91 (액) < 100 < 60 < 30 < 15 < 15 < 15
100 to 200 (액) < 180 < 90 < 30 < 20 < 15
220 to 3.3 k (액) < 90 < 60 < 20 < 15 < 15

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006

– ER113 –
 Metal (Oxide) Film
Fusing Resistors, ERQH, C

■ Maximum open circuit voltage for ERQH, C type

Maximum open circuit voltage

Referring to the maximum value of the voltage applied between terminals of the resistor when the resistor is
opened in an electric circuit, it is defined by type and resistance. Please stay within the specified voltage.
Confirm in actual circuit before use.

ERQH, C type

Testing circuit

ERQ1C type ERQ12H type

1000 1000
Maximum open circuit voltage (V)

Maximum open circuit voltage (V)

100 100

10 10
0.1 1 10 100 1000 10000 0.1 1 10 100 1000 10000
Resistance value (액) Resistance value (액)

ERQ2C type ERQ3C type

1000 1000
Maximum open circuit voltage (V)

Maximum open circuit voltage (V)

100 100

10 10
0.1 1 10 100 1000 10000 0.1 1 10 100 1000 10000
Resistance value (액) Resistance value (액)

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006

– ER114 –
 Metal (Oxide) Film
Fusing Resistors, ERQH, C

Safety Precautions

The following are precautions for individual products. Please also refer to the precautions common to Fixed Resistors
shown on page ER3 of this catalog.

1. Checking the fusing conditions

1) Fusing characteristics differ depending on the type, shape, and resistance. Check the fusing conditions
before selecting the type of Metal (Oxide) Film Fusing Resistors (hereafter called the fusing resistors) to be
used.
2) Use the fusing resistors under the maximum open circuit voltage. Otherwise, arcing may occur when a voltage
much higher than the rated one is applied in the event of an abnormality in the circuit, or when a high voltage
is applied after fusing.
2. Checking for pulse voltage, impact voltage, and transient voltage
Make sure to evaluate and check the fusing resistors mounted on your product if they are to be mounted on
a circuit that generates an impact voltage, or if there is a possibility that the transient phenomenon
(significantly high voltage applied in a short time) may occur or that a pulse voltage with a high peak voltage
may be applied. Make sure to consult our sales staff before using the fusing resistors under special conditions.
3. Conditions of use in a steady state
Make sure that the load conditions have a sufficient allowance for the power derating curve. The characteristics
of the fusing resistors are set by using a constant voltage circuit.

(Data for Reference)

■ Pulse Characteristics (Usual)
PP : Pulse limit power (W)
VP : Pulse limit voltage (V)
Pp (Vp)

t : Pulse continuous time (s)

T : Period (s)
VR : Rated voltage (V)
t P : Rated power (W)
R : Resistance value (액)
T Vp max. : Max. pulse limit voltage (V)

Withstand pulse limit power is calculated by the next

method. Type K Vp max. (V)
PP = K · P · T/t
ERQ12H 0.60 200
VP = 앀 K · P · R · T/t
ERQ1C 0.30 200
Reference to the right about a fixed number of VP max.
ERQ2C 0.25 300
ERQ3C 0.20 300

● T>1(s) 촞 T=1(s)
● T/t>100 촞 T/t=100
● PP<P 촞 P stands for PP
(VP<VR 촞 VR stands for VP)
● Added voltage<Vp max.
● PP or VP is reference value
Conditions : Pulse added time=1000 h
Resistance change=±5 %
Room temperature

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006

– ER115 –
 Metal (Oxide) Film
Fusing Resistors, ERQH, C

■ Fusing Characteristics (Constant Voltage Circuit)

(For fusing specifications, refer to page ER113)
ERQ12H ERQ1C

1액 1액
100 100 액 100 100 액
70 1k액 70 1k액
60 60
50 50
40 40
30 30
Fusing time (s)

Fusing time (s)

20 20

10 10
7 7
6 6
5 5
4 4
3 3
2 2

1 1
0 8 10 12 15 20 25 30 0 8 10 12 15 20 25 30
Multiple of the rated power Multiple of the rated power

ERQ2C ERQ3C
1액 1액
100 100 액 3.3 k 액
70 1k액 200
60
50
40 100
30
Fusing time (s)

20 50

10
Fusing time (s)

7
6
5
4 10
3 7
2 6
5
4
1 3
0 8 10 12 15 20 25 30 2
Multiple of the rated power

1
0 8 10 12 15 20 25 30
Multiple of the rated power

■ Hot Spot Temperature (for Reference)

500
Temperature rise 왕T (K)

400
2CJ680
Measuring point
300

3CJ1R0
200 1CJ680

100

12HJ680

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Multiple of the rated power

Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006

– ER116 –
 Safety Precautions
(Common precautions for Fixed Resistors)

• When using our products, no matter what sort of equipment they might be used for, be sure to make a written
agreement on the specifi cations with us in advance. The design and specifi cations in this catalog are subject
to change without prior notice.
• Do not use the products beyond the specifications described in this catalog.
• This catalog explains the quality and performance of the products as individual components. Before use, check
and evaluate their operations when installed in your products.
• Install the following systems for a failsafe design to ensure safety if these products are to be used in equipment
where a defect in these products may cause the loss of human life or other significant damage, such as damage to
vehicles (au to mo bile, train, vessel), traffi c lights, medical equipment, aerospace equipment, elec tric heating
appliances, combustion/gas equipment, rotating equipment, and disaster/crime prevention equipment.
✽ Systems equipped with a protection circuit and a protection device
✽ Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault

(1) Precautions for use

• These products are designed and manufactured for general and stan dard use in general elec tron ic
equipment (e.g. AV equipment, home electric ap plianc es, offi ce equipment, information and com mu ni cation
equipment)
• These products are not intended for use in the following special conditions. Before using the products, carefully
check the effects on their quality and performance, and determine whether or not they can be used.
1. In liquid, such as water, oil, chemicals, or organic solvent
2. In direct sunlight, outdoors, or in dust
3. In salty air or air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
4. Electric Static Discharge (ESD) Environment
These components are sensitive to static electricity and can be damaged under static shock (ESD).
Please take measures to avoid any of these environments.
Smaller components are more sensitive to ESD environment.
5. Electromagnetic Environment
Avoid any environment where strong electromagnetic waves exist.
6. In an environment where these products cause dew condensation
7. Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin
or other materials
• These products generate Joule heat when energized. Carefully position these products so that their heat will not
affect the other components.
• Carefully position these products so that their temperatures will not exceed the category temperature range due
to the effects of neighboring heat-generating components. Do not mount or place heat-generating components or
inflammables, such as vinyl-coated wires, near these products .
• Note that non- cleaning solder, halogen-based highly active fl ux, or water-soluble fl ux may deteriorate the
performance or reliability of the products.
• Carefully select a fl ux cleaning agent for use after soldering. An unsuitable agent may deteriorate the
performance or reliability. In particular, when using water or a water-soluble cleaning agent, be careful not to leave
water residues. Otherwise, the insulation performance may be deteriorated.

(2) Precautions for storage

The performance of these products, including the solderability, is guaranteed for a year from the date of arrival at your
company, provided that they remain packed as they were when delivered and stored at a temperature of 5 °C to 35 °
C and a relative humidity of 45 % to 85 %.

Even within the above guarantee periods, do not store these products in the following conditions. Otherwise, their
electrical performance and/or solderability may be deteriorated, and the packaging materials (e.g. taping materials)
may be deformed or deteriorated, resulting in mounting failures.
1. In salty air or in air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
2. In direct sunlight

<Package markings>
Package markings include the product number, quantity, and country of origin.
In principle, the country of origin should be indicated in English.

Feb. 2006

– ER3 –