®
SABIC PP 500P
POLYPROPYLENE HOMOPOLYMER
REGION ASIA
DESCRIPTION
®
SABIC PP 500P is a medium flow, multipurpose grade for extrusion and injection molding applications.
TYPICAL APPLICATIONS
If applied for extrusion 500P shows an excellent stretch ability and is therefore suitable for tapes and strapping, high tenacity yarns and carpet backing. It
can also be used in ropes and twines, woven bags, flexible intermediate bulk containers, geotextiles and concrete reinforcements.
For thermoforming it shows a unique balance between transparency, impact resistance and thickness uniformity.
500P is also suitable for production of injection molded articles e.g. caps and closures and house ware products, where this grade shows a high stiffness,
combined with a fair impact resistance and very good surface hardness.
TYPICAL PROPERTY VALUES Revision 20201207
PROPERTIES TYPICAL VALUES UNITS TEST METHODS
POLYMER PROPERTIES
Melt Flow Rate
at 230°C and 2.16kg 3 g/10 min ASTM D1238
Density
at 23°C 905 kg/m³ ASTM D638
MECHANICAL PROPERTIES
Flexural Modulus (1% Secant) 1500 MPa ASTM D790 A
Izod Impact Strength
notched, at 23°C 25 J/m ASTM D256
Rockwell Hardness, R-Scale 102 - ASTM D785
FILM PROPERTIES
(1)
Tensile Properties
stress at yield 35 MPa ASTM D638
strain at yield 10 % ASTM D638
THERMAL PROPERTIES
Vicat Softening Temperature 152 °C ASTM D1525
(2)
Heat deflection temperature
at 455kPa 100 °C ASTM D648
(1) Based on injection molded specimens.
(2) Flat wise ( testbar 80*10*4mm)
PROCESSING CONDITIONS
Typical processing conditions for 500P are:
Barrel temperature range: 235 - 250°C
HEALTH, SAFETY AND FOOD CONTACT REGULATIONS
Material Safety Data Sheets (MSDS) and Product Safety declarations are available on our Internet site http://www.SABIC.com. For additional specific
© 2020 Copyright by SABIC. All rights reserved
information please contact SABIC local representative.
The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/ medical applications.
This grade material is UL registered under File E111275 (www.ul.com).
QUALITY
(2)
Heat deflection temperature
at 455kPa 100 °C ASTM D648
(1) Based on injection molded specimens.
(2) Flat wise ( testbar 80*10*4mm)
PROCESSING CONDITIONS
Typical processing conditions for 500P are:
Barrel temperature range: 235 - 250°C
HEALTH, SAFETY AND FOOD CONTACT REGULATIONS
Material Safety Data Sheets (MSDS) and Product Safety declarations are available on our Internet site http://www.SABIC.com. For additional specific
information please contact SABIC local representative.
The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/ medical applications.
This grade material is UL registered under File E111275 (www.ul.com).
QUALITY
SABIC Europe is fully certified in accordance with the internationally accepted quality standard ISO9001.
STORAGE AND HANDLING
Polypropylene resin should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably
do not exceed 50°C. SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell
and inadequate product performance. It is advisable to process PP resin within 6 months after delivery.
DISCLAIMER
Any sale by SABIC, its subsidiaries and affiliates (each a “seller”), is made exclusively under seller’s standard conditions of sale (available upon request) unless agreed
otherwise in writing and signed on behalf of the seller. While the information contained herein is given in good faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED,
INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE
PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each customer must determine the suitability of seller
materials for the customer’s particular use through appropriate testing and analysis. No statement by seller concerning a possible use of any product, service or design is
intended, or should be construed, to grant any license under any patent or other intellectual property right.
© 2020 Copyright by SABIC. All rights reserved
