ENGINE

SECTION
EXHAUST SYSTEM
EX EX

E
CONTENTS
PRECAUTION ............................................... 2 PERIODIC MAINTENANCE ......................... 4 F

PRECAUTIONS ................................................... 2 EXHAUST SYSTEM ........................................... 4

Removal and Installation ........................................... 2 Inspection ................................................................. 4 G
PREPARATION ............................................ 3 REMOVAL AND INSTALLATION ................ 5
PREPARATION ................................................... 3 EXHAUST SYSTEM ........................................... 5 H
Special Service Tools ................................................ 3 Exploded View .......................................................... 5
Commercial Service Tools ........................................ 3 Removal and Installation .......................................... 5
Inspection ................................................................. 6 I

EX-1
 PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Removal and Installation INFOID:0000000005988494

CAUTION:
• Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance, and shape.
• Perform the operation with the exhaust system fully cooled down because the system will be hot
just after engine stops.
• Be careful not to cut your hand on the heat insulator edge.

EX-2
 PREPARATION
< PREPARATION >
PREPARATION A
PREPARATION
Special Service Tools INFOID:0000000005988495
EX

Tool number
Description C
Tool name
KV10114400 Loosening or tightening heated oxygen sen-
Heated oxygen sensor wrench sor 2
a: For 22 mm (0.87 in) width hexagon nut D

E
S-NT636

Commercial Service Tools INFOID:0000000005988496 F

Tool name Description

G
Power tool Loosening nuts and bolts

I
PBIC0190E

Heated oxygen sensor thread cleaner Reconditioning the exhaust system threads
before installing a new heated oxygen sensor J
(Use with anti-seize lubricant shown below.)
A: J-43897-18 [18 mm (0.71 in) dia.] for zir-
conia heated oxygen sensor
B: J-43897-12 [12 mm (0.47 in) dia.] for tita- K
nia heated oxygen sensor
C: Mating surface shave cylinder
JPBIA0238ZZ D: Flutes
L
Anti-seize lubricant (Permatex 133AR Lubricating heated oxygen sensor thread
or equivalent meeting MIL specifica- cleaner when reconditioning exhaust system
tion MIL-A-907) threads
M

N
AEM489

EX-3
 EXHAUST SYSTEM
< PERIODIC MAINTENANCE >
PERIODIC MAINTENANCE
EXHAUST SYSTEM
Inspection INFOID:0000000005988497

Check exhaust pipes, muffler, and mounting for improper attach-

ment, leakage, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.

SMA211A

EX-4
 EXHAUST SYSTEM
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION A
EXHAUST SYSTEM
Exploded View INFOID:0000000005988498
EX

JPBIA3372GB J

1. Seal bearing 2. Spring 3. Heated oxygen sensor 2

4. Exhaust front tube 5. Seal bearing 6. Mounting bracket
K
7. Center muffler 8. Ring gasket 9. Main muffler
Refer to GI-4, "Components" for symbols in the figure.

Removal and Installation INFOID:0000000005988499

L

REMOVAL
• Disconnect each joint and mounting. M
• Remove heated oxygen sensor 2 with following procedure:
- Using heated oxygen sensor wrench [SST: KV10114400] (A),
removal heated oxygen sensor 2 (1). N

2 : Exhaust front tube

CAUTION: O
Be careful not to damage heated oxygen sensor 2.

JPBIA3468ZZ

INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Always replace seal bearings with new ones when reassembling.

EX-5
 EXHAUST SYSTEM
< REMOVAL AND INSTALLATION >
• Discard any heated oxygen sensor 2 which has been dropped onto a hard surface such as a con-
crete floor. Use a new one.
• Before installing a new heated oxygen sensor 2, clean exhaust system threads using the heated oxy-
gen sensor thread cleaner [commercial service tool: J-43897-18 or J-43897-12] and apply anti-seize
lubricant (commercial service tool).
• Never over torque heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the “MIL” coming on.
• If heat insulator is badly deformed, repair or replace it. If deposits such as mud pile up on the heat
insulator, remove them.
• When installing heat insulator avoid large gaps or interference between heat insulator and each
exhaust pipe.
• Remove deposits from the sealing surface of each connection. Connect them securely to avoid gas
leakage.
• When installing each mounting rubber, use silicon oil to avoid twisting.
• Temporarily tighten mounting nuts and bolts. Check each part for unusual interference and mount-
ing rubber interference, and then tighten them to the specified torque.
• When installing each mounting rubber, avoid twisting or unusual extension in up/down, front/rear
and right/left directions.
Exhaust Manifold to Exhaust Front Tube
1. Securely insert seal bearing (2) into exhaust manifold (1) side in
the direction shown in the figure.

3 : Spring
4 : Nut
5 : Stud bolt
6 : Exhaust front tube
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
JPBIA2372ZZ
2. With spring, tighten nut.
CAUTION:
• Fasten stud bolts to the flange of exhaust manifold side to the specified torque before fastening
mounting nuts.
• Ensure springs are seated correctly on the flange and not sitting on (A).
• Be careful that stud bolt does not interfere with mounting hole of exhaust front tube ( ).
3. After installing, check that stud bolt does not interfere with mounting hole of exhaust front tube.
Exhaust Front Tube to Center Muffler
1. Securely insert seal bearing (2) into exhaust front tube (1) side
in the direction shown in the figure.

3 : Spring
4 : Bolt
5 : Center muffler
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. With spring, tighten bolt. JPBIA2174ZZ
CAUTION:
• Ensure springs are seated correctly on the flange and not sitting on (A).
• Be careful that bolt does not interfere with mounting hole of center muffler ( ).
3. After installing, check that bolt does not interfere with mounting hole of center muffler.
Inspection INFOID:0000000005988500

INSPECTION AFTER INSTALLATION

• Check clearance between tail tube and rear bumper is even.

EX-6
 EXHAUST SYSTEM
< REMOVAL AND INSTALLATION >
• With engine running, check exhaust tube joints for gas leakage and unusual noises.
• Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue A
stress. Improper installation could result in excessive noise and vibration.

EX

EX-7