SIWAREX® CS “Getting started”

Info Status 20.06.2004

Warning and Safety Terms
This product info contains notices that are for your personal safety and to prevent material
damages. These notices are indicated by a warning triangle and are presented as follows
depending on the degree of danger:
Danger
! Means that failure to take the necessary safety precautions will result in death,
serious injury and/or considerable property damage.

Warning
! Means that death, severe injury or extensive damage to equipment can be
caused, if the respective safety measures are not taken.

Caution
! Means that material damage or minor injuries can result if the corresponding
safety precautions are not followed carefully.

Caution
Means that material damage can result if the corresponding safety precautions
are not followed carefully.

Attention
Refers to important information on the product, handling of a product or a
corresponding segment of the documentation to which special attention should be
given.

Qualified Personnel
Commissioning and operation of a device may only be performed by qualified personnel. Qualified personnel, in
regards to the technical safety notices in this product information are persons, who have been assigned with the right to
operation, to ground and to certify devices, systems and power circuits according to the applicable safety standards.
Intended Utilization

Warning
! The device may only be utilized for the applications described in the catalog and the technical
description and only in conjunction with external devices and components that are approved or
recommended by Siemens.
Fault-free and safe operation of the product depend on proper transport, proper storage, assembly,
installation, operation and maintenance.

Brand names / Trademarks

SIWAREX®, SIMATIC®, SIMATIC HMI® and SIMATIC NET® are trade marks of the Siemens
AG. The other designations in this info may be trade marks the use of which by third persons for
their own purposes might infringe proprietor rights.
©
Copyright Siemens AG 2003 All rights reserved Disclaimer
Circulation or duplication of this document, utilization and We have tested the contents of this document for compatibility
disclosure of its contents are not permitted unless explicitly with the hardware and software described. This does not
approved. Offenders will be liable for damages. All rights exclude the possibility of discrepancies, in which case we do
reserved, including rights created by granting of patents or not guarantee the complete compatibility of this document. The
registration of a utility model or design. information in this document is assessed regularly and any
necessary corrections are included in the next revision.
Siemens AG We are grateful for any suggestions for improvement.
Automation & Drives Dept.
SIWAREX Weighing Systems © Siemens AG 2003
A&D PI 14 Subject to change without notice.
Östliche Rheinbrückenstr. 50
D-76187 Karlsruhe

iv SIWAREX FTA
SIWAREX CS

Safety Instructions

Table of Contents

Preface 1
“Getting started” for SIWAREX CS Scope of Delivery 2
Overview 3
Information
Operator Info 4
Configuring 5
Technical Data
6

Accessories
7

Issue 06/2004

SIWAREX FTA v
Contents
1 Preface.................................................................................................................................... 1-1
1.1 PURPOSE OF THE INFORMATION ................................................................................................ 1-1
1.2 PREPARATIONS FOR THE “GETTING STARTED” SOFTWARE ........................................................ 1-1
1.3 REQUIRED BASIC KNOWLEDGE ................................................................................................. 1-1
1.4 FURTHER SUPPORT .................................................................................................................... 1-1
2 Scope of Delivery .................................................................................................................. 2-2
2.1 SYSTEM PREREQUISITES ............................................................................................................ 2-2
3 Overview................................................................................................................................. 3-3
3.1 GENERAL .................................................................................................................................. 3-3
3.2 BENEFITS................................................................................................................................... 3-3
3.3 APPLICATION RANGE ................................................................................................................ 3-3
3.4 STRUCTURE ............................................................................................................................... 3-3
3.5 FUNCTION ................................................................................................................................. 3-4
3.6 COMMISSIONING- AND SERVICE WITH SIWATOOL CS ........................................................... 3-5
4 Operator Info.......................................................................................................................... 4-6
4.1 GENERAL .................................................................................................................................. 4-6
4.2 START SCREEN .......................................................................................................................... 4-6
4.3 SCALE VIEW .............................................................................................................................. 4-6
4.4 MENU ........................................................................................................................................ 4-7
4.5 OPERATING AND MONITORING .................................................................................................. 4-8
4.6 SERVICE SECTION ...................................................................................................................... 4-8
4.7 SCALE PARAMETERS .................................................................................................................4-12
4.8 MEANING OF THE FUNCTION KEYS ..........................................................................................4-13
5 Configuring .......................................................................................................................... 5-15
5.1 COMMAND GROUPS..................................................................................................................5-15
5.2 PROGRAM INSTALLATION IN STEP7.........................................................................................5-15
5.3 COMMAND MANAGER FC30 ....................................................................................................5-15
5.4 CALLING THE SCALE FB...........................................................................................................5-17
5.5 ALARMS ...................................................................................................................................5-18
5.6 CONFIGURING WITH PROTOOL .................................................................................................5-18
5.7 PROGRAM INSTALLATION IN PROTOOL ....................................................................................5-18
5.7.1 Setting up another CPU...................................................................................................5-18
5.7.2 Setting up another TP/OP................................................................................................5-19
6 Technical Data ..................................................................................................................... 6-20
6.1 PROGRAM SCOPE ......................................................................................................................6-20
6.2 CYCLE TIME .............................................................................................................................6-20
7 Accessories and Expansions............................................................................................. 7-21

Images
FIGURE 3-1 PROGRAM STRUCTURE STEP7 FOR SIWAREX CS “GETTING STARTED”.... 3-4
FIGURE 3-2 INITIAL COMMISSIONING WITH SIWATOOL CS ............................................... 3-5
FIGURE 4-1 START SCREEN FOR TOUCH PANEL TP270 ........................................................ 4-7
FIGURE 4-2 SCREEN – MENU FOR SIWAREX CS ..................................................................... 4-7
FIGURE 4-3 SCREEN – OPERATING AND MONITORING ........................................................ 4-8
FIGURE 4-4 SCREEN – SCALE ADJUSTMENT PAGE 1............................................................. 4-9
FIGURE 4-5 SCREEN – SCALE ADJUSTMENT PAGE 2............................................................. 4-9
FIGURE 4-6 SCREEN – SCALE ADJUSTMENT PAGE 3............................................................4-10
FIGURE 4-7 SCREEN – SCALE ADJUSTMENT PAGE 4............................................................4-10
FIGURE 4-8 SCREEN – SCALE ADJUSTMENT PAGE 5............................................................4-11
FIGURE 4-9 SCREEN – READ MODULE DATA .........................................................................4-11
FIGURE 4-10 SCREEN – SETTINGS FOR THE TOUCH PANEL .................................................4-12
FIGURE 4-11 SCREEN – EXTERNAL TARE DEFINITION ..........................................................4-12

vi SIWAREX FTA
SIWAREX CS

FIGURE 4-12 SCREEN – LIMIT VALUE PARAMETER ...............................................................4-13

FIGURE 5-1 CALLING THE FC COMMAND MANAGER..........................................................5-16
FIGURE 5-2 FC COMMAND MANAGER CALL..........................................................................5-16
FIGURE 5-3 CALL PARAMETERS FOR FB SICS_BA ................................................................5-17
FIGURE 5-4 CALL PARAMETERS FOR FB SICS_DR ................................................................5-17
FIGURE 5-5 CALL PARAMETER FOR THE MESSAGE BLOCK FC2 ......................................5-18

Tables
TABLE 6-1 REQUIRED MEMORY ..............................................................................................6-20
TABLE 6-2 CYCLE TIME .............................................................................................................6-20

SIWAREX FTA vii

 Preface

1 Preface

1.1 Purpose of the Information

All of the information required for setting up the system with SIWAREX CS “Getting
started” is in this information.

1.2 Preparations for the “Getting started” software

This demo-software shows the setup work required for the SIWAREX CS in
SIMATIC S7 through a set of examples. This demo-software may be changed,
copied or expanded. Any claims resulting from the use of the demo-software
are excluded.

1.3 Required Basic Knowledge

In order to understand the product information, certain knowledge concerning the

SIMATIC automation technology and SIWARIX CS is required. Weighing
technology knowledge is also an asset.

1.4 Further Support

Do you have any more questions about using the SIWAREX CS ? Then please
contact your Siemens representative in the office or business location that is
responsible for your area or technical support for SIWAREX
Tel.: +49 (0)721 595 2811.
Updated information on SIWAREX weighing technology can be found on the
relevant Internet site.
http://www.siwarex.com

SIWAREX CS 1-1
 Scope of Delivery

2 Scope of Delivery

2.1 System Prerequisites

The project has been created for the following ET 200S – heads:
- CPU head and Touch Panel TP270B (Full version)
- CPU 315-2 DP and High Feature – Head and Touch Panel TP270B (Full
version)
- CPU 315-2 DP and Standard head (Mini-version without data record
communication) and Touch Panel TP270B
- CPU 315-2 DP and Basic head (Mini-version without data record
communication) and Touch Panel TP270B
The project is made up of two parts:
- STEP7 Software for the CPU
- ProTool Software for the Touch Panel TP270B.
Both parts can set up again to be used with other devices:
- STEP7 Software with all CPUs from series S7-300 and S7-400 and a head ET
200S.
- ProTool Software can be converted in the devices TP/OP/MP 170/270/370.
The message system (FC2) is bit-based. This way, incoming messages from
SIWAREX CS are shown to the operator.
The basic equipment is also required for the setup work – the configuration
package SIWAREX CS for SIMATIC S7 (Order number 7MH4910-0AK01). This
configuration package consists of the following:
- SIWATOOL CS Commissioning program for Windows
- Hardware Update for the SIMATIC Manager hardware catalog
- Standard software for operating the SIWAREX CS in SIMATIC S7
- Device manuals in several languages
System prerequisites for using SIWAREX CS “Getting started”:
- SIMATIC STEP7 Version 5.2 and higher
- ProTool Version 6.0 and higher

SIWAREX CS 2-2
Overview

3 Overview

3.1 General

SIWAREX CS (Compact Scale) is a versatile and flexible weighing module, which

can be used wherever static scales are to be used in the ET 200S automation
system or a force measurement is necessary.
The SIWAREX CS function module (FM) can be used in SIMATIC ET 200S and
takes full advantage of all the features of the modern automation system, including
the integrated communication, the diagnostic system and the configuration tools.
The SIWAREX CS “Getting started” software supports you in starting with
application setup. A scale can be controlled by the operator using a control unit
SIMATIC HMI e.g. TP270B. The software is open and provided with commentary,
so that the user can change the software, expand it and easily modify it according
to customer wishes.

3.2 Benefits

SIWAREX CS “Getting started” is characterized by a number of clear advantages:

o Complete solutions for a scale
o Open and prepared for project-specific extensions
o SIWAREX CS – integrated messages through message bits

3.3 Application Range

SIWAREX CS “Getting started” is the optimal solution anywhere that integrating

weighing technology directly into the automation system would be advantageous.
Weighing is then a component of complex processes which are controlled by the
automation system.

3.4 Structure

The project is made up of two parts:

- STEP7 software for the SIMATIC CPU
- ProTool project (integrated in SIMATIC Manager)
A message block is also used. In this way, messages from SIWAREX CS are
displayed to the operator. The messages are created on a bit basis with this

SIWAREX CS 3-3
 message block (FC2). Of course the message system can be integrated into the
customer's message system.

3.5 Function

Weight measurement is run completely from the weighing module as if in

separately constructed weighing electronics. The integration in SIMATIC allows
weight values to be transferred directly into the PLC program. This way, there is
sensible task distribution: the weighing functions are performed in the SIWAREX-
CS module, latching and signal linking is done in the PLC.
SIWAREX CS “Getting started” takes over the tasks of a standardized program in
the SIMATIC S7. In SIWAREX CS “Getting started”, the FB scales are called, the
commands and adjustment values are passed on to the scales corresponding with
the progress of the process and the data from the scales is prepared for the
visualization.

Figure 3-1 Program structure STEP7 for SIWAREX CS “Getting started”

3-4 SIWAREX CS
Overview

3.6 Commissioning- and Service with SIWATOOL CS

SIWATOOL CS is part of the scope of the delivery of the SIWAREX CS

configuration package for SIMATIC S7 (Order number 7MH4910-0AK01). To
perform commissioning, the program must be installed on a PC first. The PC and
SIWAREX FTA are connected by the cable provided as an accessory.
Using the SIWAREX CS “Getting started” program, the adjustment parameters
(data record 3) and limit values (data record 4) can be changed at a later time and
the scale can be also be similarly readjusted later using a Touch Panel like with
SIWATOOL CS.

Figure 3-2 Initial commissioning with SIWATOOL CS

SIWAREX CS 3-5
4 Operator Info

4.1 General

The description for the operator should describe the operation and monitoring of
the weighing installation. The description corresponds with the current status of the
SIWAREX CS “Getting started” software.
The descriptions for individual scale parameters and scale functions can be found
in the SIWAREX CS and are not explained individually in the display of the
individual SIWAREX CS “Getting started” screens.
All of the existing screens are shown in this product info.

4.2 Start Screen

The program starts with the SIMATIC – Configuration screen . The scale view can
be selected from this screen. The start screen can be replaced with another image
such as a customer logo.

4.3 Scale View

The operator of the scale can perform operations and monitoring from the Scale
View image. The weight is displayed In the center of the screen.
The explanation of the function of the buttons is found in chapter: Meaning of the
Function Keys 4.8.

4-6 SIWAREX CS
Operator INFO

Figure 4-1 Start screen for Touch Panel TP270

4.4 Menu
The operator can control and observe from this menu screen or he can select the
service section for commissioning the scale.

Figure 4-2 Screen – Menu for SIWAREX CS

SIWAREX CS 4-7
4.5 Operating and Monitoring

In the scale view screen, the current scale status can be observed. Commands can
be sent to the scale by pressing buttons.

Figure 4-3 Screen – Operating and Monitoring

4.6 Service section

The following screens can be selected from the service section:

- Adjustment (5 screens)
- Read module data (1 screen)
- Settings for language and the Touch Panel

4-8 SIWAREX CS
Operator INFO

Figure 4-4 Screen – Scale adjustment Page 1

Figure 4-5 Screen – Scale adjustment Page 2

SIWAREX CS 4-9
Figure 4-6 Screen – Scale adjustment Page 3

Figure 4-7 Screen – Scale adjustment Page 4

4-10 SIWAREX CS
Operator INFO

Figure 4-8 Screen – Scale adjustment Page 5

Figure 4-9 Screen – Read module data

SIWAREX CS 4-11
Figure 4-10 Screen – Settings for the Touch Panel

4.7 Scale parameters

The tare weight and the limit values can be predefined as weighing parameters for the
SIWAREX CS.

Figure 4-11 Screen – External tare definition

4-12 SIWAREX CS
Operator INFO

Figure 4-12 Screen – Limit value parameter

4.8 Meaning of the Function Keys

The function keys have the following meaning:

View alarm buffer

Reset current alarms

Next page

Previous page

Tare

SIWAREX CS 4-13
 Delete tare weight

Activate preset tare

Take tare weight from the SIMATIC

Show tare weight for 5 sec.

Scale zero setting

Activate 10-fold resolution for 5 sec.

Read appropriate data record out of SIWAREX FTA

Send appropriate data record to SIWAREX FTA

Save data record with limit values (DS4) in flash

Save data record with zero set values (DS26)

Previous screen

4-14 SIWAREX CS
Configuring

5 Configuring

5.1 Command Groups

The SIWAREX CS “Getting started” software is defined for operation with a scale.

5.2 Program installation in STEP7

You can find the SIWAREX CS module in SIMATIC HW catalog in PROFIBUS DP,
ET 200S in the group of function modules.
If you can not find SIWAREX CS in the SIMATIC Manager the SIWAREX CS
module must first be inserted in the HW catalog. Select the function "Install HW
updates" from the „Tools“ menu. Then select „Install from file“. The file for updating
the SIWAREX CS module is located in the UPDATE_FOR_SIMATIC_S7 directory
of the SIWAREX CS configuration package for S7 (Order number 7MH4910-
0AK01). After the update, SIWAREX CS can be found under the FM modules for
ET 200S.
If you are using the same SIMATIC CPU, as in the project, you can simply load the
software from the project into the CPU. The program can be run immediately
afterward.
If you are using a different CPU, the hardware must be planned in the HW_Konfig
first. The current CPU must be deleted and replaced with the new CPU in this
case. When asked whether the program should also be deleted, enter "No".
Then transfer the program modules (FBs, FCs, OBs, DBs but not the SDB) to the
module folder in the new CPU.

5.3 Command Manager FC30

The commands of a scale are controlled by the appropriate function FC30. Using
function FC30 the commands can be executed on the scale by three different job
slots with different priorities.
CMD1 has the highest priority, CMD3 the lowest.
Calling the command manager is done in the OB1 in network 3. The commands
are actuated through various points in the program:
- by the operator at OP/TP with priority 2
- by time OB35 with priority 3
Priority 1 is not occupied.

SIWAREX CS 5-15
 CALL "Fc Execute command"
iCmdInput :="DB_SCALE_CS".i_CMD_INPUT
boCmdEnable :="DB_SCALE_CS".bo_CMD_TRIGGER
boCmdInProgress:="DB_SCALE_CS".bo_CMD_IN_PROGRESS
boCmdFinishedOk:="DB_SCALE_CS".bo_CMD_FINISHED_OK
boCmdErr :="DB_SCALE_CS".bo_CMD_ERR
sCmd_1 :=DB21.DBD24
sCmd_2 :=DB21.DBD28
sCmd_3 :=DB21.DBD32

Figure 5-1 Calling the FC Command Manager

The input variable s_Cmd_1 contains the command code and the control bits for
the command handling.
If FC30 is used as a command manager, the commands may not be transferred
directly to the SIWAREX by calling FB42/FB43, but through structure CMD1,
CMD2, CMD3.

s_CMD1 STRUCT Command input 1

i_CMD1_Code INT 0 Command code

bo_CMD1_Trigger BOOL FALSE Command trigger

bo_CMD1_InProgress BOOL FALSE Command in progress

bo_CMD1_FinishedOk BOOL FALSE Command finished ok

bo_CMD1_FinishedError BOOL FALSE Command finished with error

Figure 5-2 FC Command Manager Call

5-16 SIWAREX CS
Configuring

5.4 Calling the Scale FB

Calling the FB SICS_DR or SICS_BA is done in OB1. The FB is called with the
following parameters:

For the Basic and Standard head, FB SICS_BA is called as follows:

CALL “SICS_BA” , DB42
ADDR :=256
DB_SCALE :=22
CMD_IN :=”DB_SCALE_CS”.i_CMD_INPUT
SEL_PROC_VAL :=”DB_SCALE_CS”.b_SELECT_PROC_VAL
EXT_TARA :=”DB_SCALE_CS”.i_PRESET_TARE
CMD_INPR :=”DB_SCALE_CS”.bo_CMD_IN_PROGRESS
CMD_FOK :=”DB_SCALE_CS”.bo_CMD_FINISHED_OK
CMD_ERR :=”DB_SCALE_CS”.bo_CMD_ERR
CMD_ERR_C :=”DB_SCALE_CS”.b_CMD_ERR_CODE
REF_COUNT :=”DB_SCALE_CS”.b_INFO_REFRESH_COUNT
ACT_SEL_PROC_VAL:=”DB_SCALE_CS”.b_SELECTED_PROC_VAL
PROC_VAL1 :=”DB_SCALE_CS”.i_PROCESS_VALUE
SC_STATUS :=”DB_SCALE_CS”.w_SCALE_STATUS
ERR_MSG_C :=”DB_SCALE_CS”.b_OPR_ERR_MSG
FB_ERR :=”DB_SCALE_CS”.bo_FB_ERR
FB_ERR_C :=”DB_SCALE_CS”.b_FB_ERR_CODE
START_UP :=”DB_SCALE_CS”.bo_START_UP_IN_PROGRESS
CMD_EN :=”DB_SCALE_CS”.bo_CMD_TRIGGER
Figure 5-3 Call Parameters for FB SICS_BA

For the HF and CPU head, FB SICS_DRis called as follows:

CALL "SICS_DR" , DB41
ADDR :=272
DB_SCALE :=21
DB_VECTOR :=20
CMD_IN :=”DB_SCALE_CS”.i_CMD_INPUT
SEL_PROC_VAL :=”DB_SCALE_CS”.b_SELECT_PROC_VAL
EXT_TARA :=”DB_SCALE_CS”.i_PRESET_TARE
CMD_INPR :=”DB_SCALE_CS”.bo_CMD_IN_PROGRESS
CMD_FOK :=”DB_SCALE_CS”.bo_CMD_FINISHED_OK
CMD_ERR :=”DB_SCALE_CS”.bo_CMD_ERR
CMD_ERR_C :=”DB_SCALE_CS”.b_CMD_ERR_CODE
REF_COUNT :=”DB_SCALE_CS”.b_INFO_REFRESH_COUNT
ACT_SEL_PROC_VAL:=”DB_SCALE_CS”.b_SELECTED_PROC_VAL
PROC_VAL1 :=”DB_SCALE_CS”.i_PROCESS_VALUE
SC_STATUS :=”DB_SCALE_CS”.w_SCALE_STATUS
ERR_MSG_C :=”DB_SCALE_CS”.b_OPR_ERR_MSG
FB_ERR :=”DB_SCALE_CS”.bo_FB_ERR
FB_ERR_C :=”DB_SCALE_CS”.b_FB_ERR_CODE
START_UP :=”DB_SCALE_CS”.bo_START_UP_IN_PROGRESS
CMD_EN :=”DB_SCALE_CS”.bo_CMD_TRIGGER
Figure 5-4 Call Parameters for FB SICS_DR

SIWAREX CS 5-17
5.5 Alarms

The scale messages are decoded with the FC2 and converted into a bit message
field. The message texts and help texts (German and English) are integrated in the
control unit.
Of course, the user can delete these program sections and use his own message
system.
CALL FC 2
db_DB_ALARM :=DB100
i_FIRST_DBB :=20
bo_CMD_ERR :="DB_SCALE_CS".bo_CMD_ERR
b_CMD_ERR_CODE :="DB_SCALE_CS".b_CMD_ERR_CODE
b_OPR_ERR_MSG :="DB_SCALE_CS".b_OPR_ERR_MSG
bo_FB_ERR :="DB_SCALE_CS".bo_FB_ERR
b_FB_ERR_CODE :="DB_SCALE_CS".b_FB_ERR_CODE
bo_DEL_BIT_AREA:=M20.0
bo_EDGE_1 :=M20.1
bo_EDGE_2 :=M20.2

Figure 5-5 Call parameter for the message block FC2

5.6 Configuring with ProTool

The software is for setup for showing a scale in TP270B.

The conversion to other SIMATIC HMI devices is possible.
ProTool offers a selection of target devices for the conversion.

5.7 Program installation in ProTool

If you are using the planned CPU and TP270B, the program is ready for operation
immediately after loading into the TP270B (or Start of Runtime in ProTool). When
loading with the MPI interface, use MPI-address=1 for TP270B, MPI-address=2 for
the CPU and address 4 for the PROFIBUS head station.

5.7.1 Setting up another CPU

If you are using another CPU, the project must be integrated into the new
environment.

5-18 SIWAREX CS
Configuring

Select the controller from the Controllers menu in ProTool and link the controller for
the communication with the OP/TP in the Parameter menu.
Then, activate the Restore symbol in the Edit menu.
In the last step, the project must be loaded to the target OP/TP.

5.7.2 Setting up another TP/OP

If another SIMATIC-HMI device is used, the project must be integrated into the new
environment.
After activating the menu for project conversion, you are offered a list of possible
target devices. Select the device from the list and perform the conversion.
The following procedures are handled as they are when using a new CPU – see
Setting up another CPU 5.7.1.

SIWAREX CS 5-19
6 Technical Data

6.1 Program Scope

Memory requirements are shown for the HF or the CPU header.

OB /FB/FC Approx. 5.3 kB

DB Approx. 0.7 kB
Program scope ProTool Approx. 430 kB
Table 6-1 Required memory

6.2 Cycle Time

Cycle time example: Approx. 2 ms

CPU315-2 DP
Table 6-2 Cycle time

6-20 SIWAREX CS
Accessories AND EXPANSIONS

7 Accessories and Expansions

Information on expansion software for SIWAREX “Getting started” can be obtained

through the engineering office in Kaszkin: www.ib-kaszkin.de

SIWAREX CS 7-21