NOVALUX WOOD STAIN 8910
DESCRIPTIONS : Novalux Wood Stain 8910 is a ready to use pigmented
stains intended to accent and highlight grain definition
and the natural beauty of wood products.
RECOMMENDED USES : Used under all sealer and topcoat systems.
ADVANTAGES Ready to use
Clean colors attain rich wood tones
Durable Colors, Excellent Clarity, Good Workability
Free of lead and chromate hazards
TECHNICAL DATA
Colour : Standard Colour
Gloss : Matt
Specific Gravity : 1.05-1.06 kg/I
Solid By Volume : ± 10-43% varies by colour
Recommended DFT : 10-15 microns
Theoretical Coverage : 10-14 m2/l @ 10 micron
Drying Time : Temperature 25°C
Touch Dry 3 min
Hard Dry 10 min
Full Cured : -
Over Coating Interval Temperature 25°C
Minimum -
Maximum -
Flash Point : : 39°C (DIN 53213)
Recommended Surface : Surface Preparation
Preparation All lumber should be stored on the premises in dry
warm rooms to prevent absorption of moisture. The
amount of moisture contained in a piece of wood is
referred to as "moisture content" and is expressed as
a percentage indicating relative weight of the water in
the wood compare to its own dry weight. Wood
expands as it absorbs moisture and shrinks when it
loses it.
The moisture content of wood changes with the level
of moisture or humidity in the air. The Moisture
humidity in the air. The moisture content of wood at the
time it is coated should be approximately 5-8%.
All surfaces should be sanded smooth. Each
subsequent sanding should use a finer grit paper than
the previous. A Typical system would invoice using
100 grits followed by 15, 180 and touch up with 220.
The spread between grit sizes should be close enough
so as not to leave sand scratches from the first
sanding that cannot be removed by the next.
NOVALUX WOOD STAIN 8910
Recommended Surface : All sanding dust must be removed by using either a
Preparation tack rag or a blast of clean air from a spray gun. If any
dirt or greases attaches to the surface before actual
finishing, it must be removed by solvent wiping.
Wood
Must be clean, dry, and finish sanded. Moisture
content should be 6 to 8%.
Cleaning Solvent : Novalux Thinner 896
Applications : Reduction:
Reduction is normally not required. For faster drying,
reduce with toluene or naptha.
Conventional Spray:
Air Pressure .....................30-35 psi
Application as a Wiping Stain
Spray a full wet coat. Remove excess stain by wiping
using a circular motion with a soft cloth. For a deeper
color, allow some of the solvent to flash off up to 15
minutes maximum working time.
For a lighter color, reduce with mineral spirits or wipe
sooner.
If wiping becomes difficult due to dryness of the stain,
rewet with a cloth dipped in stain, the wipe again.
The stain may be applied by brush, dipping, sponge or
cloth.
Sealers or other wood finishing products may be
applied 30 minutes after wiping. For faster drying,
reduce with toluene or naptha.
Storage & Handling : The product should be ideally stored in a cool and well
ventilated place, protected from heat and direct
sunlight. Containers must be kept tightly closed before
and after use. Handle with care.
Packaging : 5 & 20 liter set
Shelf Life : 12 months @25°C
The information and recommendations herein stated to be accurate and reliable under
specific testing conditions. All recommendations or suggestions regarding the use of
such product are made without guarantee, since the conditions of the use are beyond our
control. It Is the responsibility of the customer to satisfy himself that each product is fit for
the purpose for which he intends to use and that the actual conditions of use are suitable.
The company reserves the right to modify from time according to manufacturer
experience and continuous development program.
July-09
