REPORT

ON

SUB-SOIL INVESTIGATION

FOR

proposed R.C.C BUILDING FOR JNV

at
DALKHOLA.

Client :

Malda Central Division, CPWD, Malda.

Prepared By :

IIT Guwahati.
IIT GUWAHATI SHEET NO.: 1

INTRODUCTION:

Sub-Soil Investigation was carried out at the site of

proposed R.C.C Building for JNV at Dalkhola to find out the
Engineering properties of soil types.

This report consists of details of field investigation and

laboratory analysis along with the rational interpretation
of test results to find out the type of foundation to be
adopted and safe bearing capacity for the same.

All the field investigation and laboratory test were

conducted as per IS Specification.

FIELD INVESTIGATION:

Field investigation at the site consists of vertical

boring in 11 (Eleven) locations up to maximum depth of
30.00m from existing ground level.

LOCATION OF BORE HOLE :

The bore holes were done at different locations as below :

BH No. Location BH No. Location

01 & 02. Type-II.
03 & 06. Type-III. 09. Kitchen/Dining
04 & 05. School Building 10. Girls Dormitory
07 & 08. Boys Dormitory 11. Principal’s qtr

COLLECTION OF SAMPLES:

Disturbed and undisturbed samples were collected and

Standard Penetration Test were done during boring. In
addition to these study in change of strata, ground water
level, visual identification of soil such as colour, nature
and stiffness were recorded during boring.

DISTURBED SAMPLE:

Disturbed samples were collected at different depth and

were properly packed after collection.

UNDISTURBED SAMPLE:

Undisturbed samples could not be collected on soil layer

encountered due to presence of cohesion less soil.

Contd.
IIT GUWAHATI SHEET NO.: 2

STANDARD PENETRATION TEST :

Standard Penetration Test were conducted by using standard

split spoon sampler as per IS specification. A drive weight
assembly of 63.50 Kg drop hammer for free fall of 75 cm is
used. Nos. of blows required to drive the sampler for 1st
15 cm is neglected and blows for next 30 cm is counted and
is expressed as N-value. N-value at the site is found to
vary from 01 to >100. The results of SPT are graphically
shown in the bore hole log enclosed here with.

Details of field investigation are shown in the bore hole

log enclosed here with.

LABORATORY ANALYSIS :

Selected soil samples are analyses in the laboratory.

Following laboratory test were done on soil samples.

1. Natural Moisture content. 2. Specific gravity.

3. Bulk & Dry density. 4. Grain size analysis.
5. Shear test. 6. Atterberg’s limit test.
7. Chemical Test. 8. Consolidation Test.
Moisture content of the soil varies from 14.15% to 29.61%
Specific gravity is in the range of 2.57 to 2.70 Bulk
density varies from 1.65 gm/cc to 2.14 gm/cc while Dry
density varies from 1.29 gm/cc to 1.87 gm/cc, Submerged
density varies from 0.83 gm/cc to 1.17 gm/cc Void ratio is
in the range of 0.428 to 1.00.

Grain size distribution curve shows the nature of soil

deposits. Clay varies from 5.00% to 28.00% Silt varies from
6.00% to 95.00%. Fine sand varies from 10.00% to 100.00%.
Medium sand varies from 8.00% to 18.00%. Coarse sand varies
from 3.00% to 6.00%. Fine Gravel varies from 0.00% to
9.00%.

Liquid limit of the soil varies from 27.90% to 49.10%

Plastic limit varies from NP to 26.75% while Plasticity
Index varies from NP to 22.72%.

Cohesion of the soil varies from 0.00 Kg/Cm2 to 0.21 Kg/Cm2

and angle of internal friction varies from 7 to 36.

Consolidation test cannot be done as the soil is mainly

cohesion less in nature.

Contd.
IIT GUWAHATI SHEET NO.: 3

O1 No. of Chemical Test for soil is conducted on extract of

soil sample collected at site and 01 no. for water sample.
The results of chemical test are as below :

Sl.No. pH Value Chloride ppm Sulphate ppm Carbonates Organic

matter

Results of soil sample

01. 6.70 19.82 23.59 11.62 Nil
Results of water sample
01. 7.00 13.59 21.46 5.04 Nil

Details of laboratory analysis are enclosed in the form of

table & graphs.

DISCUSSION :

From field investigation the soil layer at site are found as

below :

BH. NO. Depth (M) Description

From To

01. 0.00 3.40 Silty clay.

3.40 25.50 Silty sand and sand.

02. 0.00 3.00 Silty clay.

3.00 4.00 Black soil.
4.00 23.50 Silty sand and sand.
23.50 24.00 Sandy clay.
24.00 25.50 Sand.

03. 0.00 3.00 Clayey silt with sand.

3.00 18.00 Silty sand and sand.

04. 0.00 2.90 Silty sand.

2.90 4.00 Silty clay.
4.00 25.50 Silty sand and sand.

05. 0.00 3.00 Silty clay.

3.00 30.00 Silty sand and sand.

06. 0.00 2.00 Silty clay.

2.00 3.20 Sandy clay.
3.20 24.00 Silty sand and sand.

07. 0.00 3.50 Clayey silt with sand.

3.50 21.00 Silty sand and sand.

Contd.
IIT GUWAHATI SHEET NO.: 4

BH. NO. Depth (M) Description

From To

08. 0.00 3.20 Clayey silt with sand.

3.20 28.50 Silty sand and sand.

09. 0.00 4.30 Clayey silt with sand.

4.30 20.80 Silty sand and sand.
20.80 23.50 Clayey silt with sand.
23.50 27.00 Silty sand and sand.

10. 0.00 3.50 Clayey silt with sand.

3.50 25.50 Silty sand and sand.

11. 0.00 3.20 Clayey silt with sand.

3.20 30.00 Silty sand and sand.

Upper layer consists of clayey silt with sand followed by

layer of silty sand and sand up to termination depth of
boring.

FOUNDATION :

From the results obtained it is seen that foundation in the

proposed site should rest at minimum depth of 4.50m below
existing ground level. Under such case normal footing is not
feasible in the site. Here bored cast in situ pile of
suitable dia and minimum length of 12.00m may be adopted. In
the area covered by bore hole no. 02, 09 & 10 minimum length
of pile should be 15.00m below existing ground level.

Foundation depth for different bore hole location are as

below :

BH NO. Minimum depth of Type of foundation

foundation
1, 4, 5, 8, 4.50m Bored cast in situ pile of
& 11 suitable dia and minimum
length of 12.00m below
existing ground level.
2 6.00m -Do- 15.00m
3 & 6 3.00m -Do- 12.00m
7 6.00m -Do- 12.00m
9 & 10 4.50m -Do- 15.00m

Contd.
IIT GUWAHATI SHEET NO.: 5

SAFE BEARING CAPACITY OF SOIL :

Safe bearing capacity of soil for normal footing is not

furnished in the report as the foundation depth goes below
4.50m from existing ground level.

LOAD CARRYING CAPACITY OF PILE :

Load carrying capacity of bored cast in situ pile is

calculated by using the equation :
N
Qu = Ap (½ D۷ N۷ + PD Nq) + Σ Ki=1 PDi tan δ Asi

Where,

Ap = cross-sectional area of pile toe.

D = stem diameter.
۷ = effective unit weight of soil at pile toe .
PD = effective overburden pressure at pile toe.
N۷ and Nq = bearing capacity factors depending upon
the angle of internal friction  at toe.
n
Σi=1 = summation for n layers in which pile is
Installed.
K = coefficient of earth pressure.
PDi = effective overburden pressure for the ith layer
where I varies from 1 to n.
δ = angle of wall friction between pile and soil, in
degrees (may be taken equal to ).
Asi = surface area of pile stem.

Now for 400mm dia and 12.00m length pile carrying capacity is
calculated by using the parameters :

Ap = 0.1256 SM D = 400mm
۷ = 0.96 (Avg) MT/Cm
۷ = 1.01 (Toe) MT/Cm
PD = 7.68 MT/SM
n
Σi =1 = 1 K = 1.5
PDi = 7.68 MT/SM δ = 31º
Nq = 23.00 N۷ = 27.53
Asi = 10.048

Contd.
IIT GUWAHATI SHEET NO.: 6

Now
Qu= 0.1256 (5.361 + 176.64) + 53.976
= 76.86 MT each
Now Safe Load = 30.74 MT each (FOS=2.5)

Load carrying capacity of pile for different dia and length

are as below :

Length (M) Dia mm

400 450 500 600
Load Carrying Capacity MT each

12.00 30.74 35.92 41.40 53.23

13.00 37.58 43.78 50.30 64.58

14.00 59.60 68.70 78.17 98.21

15.00 70.84 81.53 92.55 109.38

OBSERVED N-VALUE

Depth (m) BORE HOLE NO.

01 02 03 04 05 06 07 08 09 10 11

1.50 07 04 06 06 08 06 04 06 04 05 17
2.00 04 -- -- 06 07 04 04 06 07 04 14
2.50 02 -- -- 04 04 02 06 07 09 04 06
3.00 02 02 09 01 05 10 01 07 03 05 01
4.50 10 06 08 10 11 27 07 11 12 24 09
6.00 11 09 07 15 17 15 13 14 11 19 17
7.50 14 10 13 23 20 15 24 15 18 21 18
9.00 16 17 19 32 19 37 21 17 16 22 27
10.50 18 22 18 51 21 20 16 25 26 22 30
12.00 21 15 20 65 20 26 51 28 13 12 35
13.50 24 19 24 75 35 23 33 22 31 35 28
15.00 30 46 43 53 25 21 32 20 33 32 44
16.50 31 43 49 62 40 32 35 31 50 30 39
18.00 35 44 52 99 53 46 46 23 56 36 32
19.50 42 47 46 35 39 35 105 53 66 48
21.00 24 49 97 37 38 156 110 36 125 93
22.50 83 51 171 50 90 53 11 31 90
24.00 78 54 157 68 >200 62 84 79 83
25.50 102 56 >200 73 56 102 195 78
27.00 125 76 150 166
28.50 128 112 172
30.00 123 127

Contd.
IIT GUWAHATI SHEET NO.: 7

CONCLUSION :

From careful study of test results obtained conclusions are

drawn as :

1. Upper layer consists of clayey silt with sand followed

by layer of silty sand and sand up to termination depth
of boring.

2. Foundation in the proposed site should rest at minimum

depth of 4.50m below existing ground level. Under such
case normal footing is not feasible in the site. Here
bored cast in situ pile of suitable dia and minimum
length of 12.00m may be adopted.

Foundation depth for different bore hole location may be

considered from the table of clause discussion.

Load carrying capacity of pile for different dia and

length may be considered from the table of clause
discussion.

Strict supervision is recommended during execution of

piling or stone column work.

Grade beam of suitable dimension should be provided.

3. Seismic co-efficient as per IS Specification should be

considered during design.

Contd.
IIT GUWAHATI SHEET NO.: 8

PHYSICAL PROPERTIES

B.H.No Depth Moisture Specific Bulk Dry Submerged Void

(m) Content Gravity Densi Densi Density Ratio
(%) ty ty gm/cc
gm/cc gm/cc

01. 1.50 23.64 2.59 1.76 1.42 0.87 0.818

3.00 25.71 2.60 1.72 1.37 0.84 0.800
6.00 18.58 2.66 1.75 1.47 0.92 0.802
9.00 17.26 2.67 1.80 1.54 0.96 0.739
12.00 17.45 2.67 1.89 1.61 1.01 0.659
15.00 18.67 2.68 1.96 1.65 1.03 0.623
18.00 17.32 2.68 2.01 1.71 1.07 0.564
21.00 18.59 2.69 1.98 1.67 1.05 0.611
25.50 16.18 2.69 2.08 1.79 1.12 0.503

02. 1.50 24.37 2.59 1.69 1.36 0.83 0.906

3.00 22.15 2.60 1.65 1.35 0.83 0.925
6.00 18.72 2.67 1.69 1.42 0.89 0.876
9.00 17.51 2.67 1.86 1.58 0.99 0.687
12.00 17.26 2.68 1.84 1.57 0.98 0.708
15.00 17.43 2.67 2.03 1.73 1.08 0.544
18.00 15.67 2.68 1.98 1.71 1.07 0.566
21.00 16.23 2.69 2.01 1.73 1.09 0.555
25.50 15.82 2.69 2.03 1.75 1.10 0.535

03. 1.50 24.61 2.63 1.74 1.40 0.86 0.883

3.00 19.87 2.65 1.73 1.44 0.90 0.836
6.00 20.75 2.66 1.70 1.41 0.88 0.889
9.00 17.58 2.67 1.87 1.59 0.99 0.679
12.00 17.36 2.67 1.89 1.61 1.01 0.658
15.00 16.69 2.68 1.96 1.68 1.05 0.595
18.00 15.47 2.68 2.00 1.73 1.08 0.547

04. 1.50 24.25 2.60 1.74 1.40 0.86 0.857

3.00 28.36 2.59 1.73 1.35 0.83 0.922
6.00 17.81 2.67 1.80 1.53 0.95 0.747
9.00 17.54 2.67 1.93 1.64 1.03 0.626
12.00 16.39 2.68 2.011 .73 1.08 0.552
15.00 15.82 2.69 2.03 1.75 1.10 0.535
18.00 15.69 2.69 2.06 1.78 1.12 0.511
21.00 17.38 2.68 2.07 1.76 1.11 0.520
25.50 14.45 2.67 2.14 1.87 1.17 0.428

Contd.
IIT GUWAHATI SHEET NO.: 9

B.H.No Depth Moisture Specific Bulk Dry Submerged Void

(m) Content Gravity Densi Densi Density Ratio
(%) ty ty gm/cc
gm/cc gm/cc

05. 1.50 22.73 2.63 1.72 1.40 0.87 0.877

3.00 23.65 2.64 1.70 1.37 0.85 0.920
6.00 17.21 2.67 1.84 1.57 0.98 0.701
9.00 16.48 2.68 1.85 1.59 0.99 0.687
12.00 15.25 2.67 1.87 1.62 1.01 0.645
15.00 15.81 2.69 1.91 1.65 1.04 0.631
18.00 15.76 2.68 2.02 1.74 1.09 0.536
21.00 17.34 2.68 2.00 1.70 1.07 0.572
24.00 16.15 2.69 2.06 1.77 1.11 0.517
27.00 15.58 2.67 2.11 1.82 1.14 0.462
30.00 14.69 2.69 2.13 1.86 1.17 0.448

06. 1.50 25.82 2.62 1.75 1.39 0.86 0.884

3.00 21.67 2.64 1.76 1.45 0.90 0.825
6.00 18.45 2.66 1.81 1.53 0.95 0.741
9.00 16.53 2.67 1.96 1.68 1.05 0.587
12.00 17.21 2.67 1.91 1.63 1.02 0.638
15.00 18.42 2.67 1.90 1.60 1.00 0.664
18.00 15.63 2.68 2.01 1.74 1.09 0.542
21.00 15.31 2.67 2.07 1.80 1.12 0.487
24.00 14.27 2.67 2.10 1.84 1.15 0.452

07. 1.50 24.38 2.65 1.68 1.35 0.84 0.962

3.00 29.61 2.58 1.67 1.29 0.79 1.00
6.00 18.57 2.66 1.78 1.50 0.94 0.772
9.00 16.82 2.67 1.81 1.55 0.97 0.723
12.00 17.35 2.67 1.98 1.69 1.06 0.682
15.00 18.76 2.68 1.96 1.65 1.03 0.624
18.00 16.42 2.69 1.97 1.69 1.06 0.590
21.00 15.53 2.70 2.06 1.78 1.12 0.514

08. 1.50 25.81 2.63 1.75 1.39 0.86 0.891

3.00 20.76 2.66 1.71 1.41 0.88 0.878
6.00 17.48 2.67 1.79 1.52 0.95 0.752
9.00 16.57 2.67 1.81 1.55 0.97 0.719
12.00 15.73 2.68 1.93 1.67 1.04 0.607
15.00 18.24 2.68 1.91 1.61 1.01 0.659
18.00 17.75 2.70 1.92 1.63 1.03 0.656

Contd.
IIT GUWAHATI SHEET NO.: 10

B.H.No Depth Moisture Specific Bulk Dry Submerged Void

(m) Content Gravity Densi Densi Density Ratio
(%) ty ty gm/cc
gm/cc gm/cc

08. 21.00 15.31 2.69 2.05 1.78 1.12 0.513

24.00 17.64 2.67 2.03 1.73 1.08 0.547
28.50 14.15 2.67 2.06 1.80 1.13 0.479

09. 1.50 26.37 2.59 1.73 1.37 0.84 0.892

3.00 29.21 2.57 1.75 1.35 0.83 0.898
6.00 19.58 2.66 1.76 1.47 0.92 0.807
9.00 17.34 2.67 1.80 1.53 0.96 0.743
12.00 18.48 2.67 1.79 1.51 0.94 0.767
15.00 16.25 2.68 1.96 1.69 1.06 0.589
18.00 17.12 2.69 2.01 1.72 1.08 0.567
21.00 21.75 2.66 2.02 1.66 1.04 0.603
24.00 15.63 2.67 2.06 1.78 1.11 0.499
27.00 14.35 2.68 2.10 1.84 1.15 0.459

10. 1.50 26.57 2.59 1.74 1.37 0.84 0.884

3.00 28.35 2.60 1.78 1.39 0.85 0.875
6.00 17.62 2.67 1.85 1.57 0.98 0.697
9.00 16.83 2.67 1.92 1.64 1.03 0.625
12.00 20.46 2.68 1.87 1.55 0.97 0.726
15.00 17.21 2.67 2.00 1.71 1.07 0.565
18.00 16.68 2.69 2.02 1.73 1.09 0.554
21.00 15.46 2.69 2.10 1.82 1.14 0.479
25.50 14.73 2.67 2.12 1.85 1.15 0.445

11. 1.50 24.61 2.59 1.87 1.50 0.92 0.726

3.00 29.39 2.60 1.75 1.35 0.83 0.922
6.00 18.76 2.67 1.82 1.53 0.96 0.742
9.00 17.45 2.68 1.98 1.69 1.06 0.589
12.00 16.51 2.68 2.01 1.73 1.08 0.553
15.00 16.18 2.68 2.03 1.75 1.09 0.534
18.00 17.37 2.70 2.02 1.72 1.08 0.569
21.00 15.49 2.68 2.06 1.78 1.12 0.502
24.00 15.24 2.69 2.09 1.81 1.14 0.483
27.00 14.63 2.67 2.10 1.83 1.15 0.457
30.00 14.34 2.67 2.11 1.84 1.15 0.447

Contd.
IIT GUWAHATI SHEET NO.: 11

GRAIN SIZE ANALYSIS

B.H. Depth Clay Silt Fine Medium Coarse Fine

No (M) (%) (%) Sand (%) Sand Sand Gravel
(%) (%) (%)

01. 1.50 9.00 74.00 17.00 -- -- --

3.00 11.00 66.00 23.00 -- -- --
6.00 -- 21.00 79.00 -- -- --
9.00 -- -- 100.00 -- -- --
12.00 -- -- 100.00 -- -- --
15.00 -- -- 100.00 -- -- --
18.00 -- -- 100.00 -- -- --
21.00 -- -- 100.00 -- -- --
25.50 -- -- 100.00 -- -- --

02. 1.50 10.00 72.00 18.00 -- -- --

3.00 5.00 95.00 -- -- -- --
6.00 -- 13.00 87.00 -- -- --
9.00 -- -- 100.00 -- -- --
12.00 -- -- 100.00 -- -- --
15.00 -- -- 100.00 -- -- --
18.00 -- -- 83.00 17.00 -- --
21.00 -- -- 100.00 -- -- --
25.50 -- -- 86.00 14.00 -- --

03. 1.50 -- 64.00 36.00 -- -- --

3.00 -- 32.00 68.00 -- -- --
6.00 -- 13.00 87.00 -- -- --
9.00 -- -- 100.00 -- -- --
12.00 -- -- 100.00 -- -- --
15.00 -- -- 100.00 -- -- --
18.00 -- -- 100.00 -- -- --

04. 1.50 5.00 74.00 21.00 -- -- --

3.00 23.00 63.00 14.00 -- -- --
6.00 -- 11.00 89.00 -- -- --
9.00 -- -- 90.00 10.00 -- --
12.00 -- -- 100.00 -- -- --
15.00 -- -- 82.00 18.00 -- --
18.00 -- -- 87.00 13.00 -- --
21.00 -- -- 100.00 -- -- --
25.50 -- -- 100.00 -- -- --

Contd.
IIT GUWAHATI SHEET NO.: 12

B.H. Depth Clay Silt Fine Medium Coarse Fine

No (M) (%) (%) Sand (%) Sand Sand Gravel
(%) (%) (%)

05. 1.50 -- 58.00 42.00 -- -- --

3.00 -- 37.00 63.00 -- -- --
6.00 -- -- 100.00 -- -- --
9.00 -- -- 87.00 13.00 -- --
12.00 -- -- 100.00 -- -- --
15.00 -- -- 90.00 10.00 -- --
18.00 -- -- 100.00 -- -- --
21.00 -- -- 100.00 -- -- --
24.00 -- -- 100.00 -- -- --
27.00 -- -- 100.00 -- -- --
30.00 -- -- 100.00 -- -- --

06. 1.50 -- 71.00 29.00 -- -- --

3.00 -- 32.00 68.00 -- -- --
6.00 -- 11.00 89.00 -- -- --
9.00 -- -- 100.00 -- -- --
12.00 -- -- 100.00 -- -- --
15.00 -- 15.00 85.00 -- -- --
18.00 -- -- 100.00 -- -- --
21.00 -- 10.00 90.00 -- -- --
24.00 -- 17.00 83.00 -- -- --

07. 1.50 -- 52.00 48.00 -- -- --

3.00 23.00 67.00 10.00 -- -- --
6.00 -- 15.00 85.00 -- -- --
9.00 -- -- 100.00 -- -- --
12.00 -- 11.00 89.00 -- -- --
15.00 -- -- 100.00 -- -- --
18.00 -- -- 84.00 16.00 -- --
21.00 -- -- 89.00 11.00 -- --

08. 1.50 -- 53.00 47.00 -- -- --

3.00 -- 21.00 79.00 -- -- --
6.00 -- -- 100.00 -- -- --
9.00 -- -- 100.00 -- -- --
12.00 -- -- 87.00 13.00 -- --
15.00 -- 6.00 85.00 9.00 -- --
18.00 -- -- 86.00 11.00 3.00 --
21.00 -- -- 100.00 -- -- --
24.00 -- 8.00 92.00 -- -- --
28.50 -- 19.00 81.00 -- -- --

Contd.
IIT GUWAHATI SHEET NO.: 13

B.H. Depth Clay Silt Fine Medium Coarse Fine

No (M) (%) (%) Sand (%) Sand Sand Gravel
(%) (%) (%)

09. 1.50 7.00 77.00 16.00 -- -- --

3.00 28.00 72.00 -- -- -- --
6.00 -- -- 100.00 -- -- --
9.00 -- -- 100.00 -- -- --
12.00 -- -- 100.00 -- -- --
15.00 -- -- 100.00 -- -- --
18.00 -- -- 92.00 8.00 -- --
21.00 5.00 39.00 56.00 -- -- --
24.00 -- 16.00 84.00 -- -- --
27.00 -- -- 100.00 -- -- --

10. 1.50 7.00 78.00 15.00 -- -- --

3.00 11.00 69.00 20.00 -- -- --
6.00 -- 11.00 89.00 -- -- --
9.00 -- -- 100.00 -- -- --
12.00 -- -- 100.00 -- -- --
15.00 -- 13.00 87.00 -- -- --
18.00 -- -- 90.00 10.00 -- --
21.00 -- -- 100.00 -- -- --
25.50 -- -- 100.00 -- -- --

11. 1.50 8.00 73.00 19.00 -- -- --

3.00 6.00 69.00 25.00 -- -- --
6.00 -- 11.00 89.00 -- -- --
9.00 -- -- 100.00 -- -- --
12.00 -- -- 100.00 -- -- --
15.00 -- -- 100.00 -- -- --
18.00 -- -- 84.00 10.00 6.00 --
21.00 -- -- 100.00 -- -- --
24.00 -- -- 91.00 -- -- 9.00
27.00 -- 18.00 82.00 -- -- --
30.00 -- 16.00 84.00 -- -- --

Contd.
IIT GUWAHATI SHEET NO.: 14

SHEAR PROPERTIES

B.H. No Depth Porosity. Saturated “C” “”

(M) (%) density gm/cc. Kg/Cm2 Degree

01. 1.50 45.00 1.87 0.23 8

3.00 45.00 1.84 0.10 10
6.00 44.00 1.92 0.12 18
9.00 42.00 1.96 0.04 26
12.00 40.00 2.01 0.00 31
15.00 38.00 2.03 0.00 32
18.00 36.00 2.07 0.00 32.5
21.00 38.00 2.05 0.00 33
25.50 33.00 2.12 0.00 34

02. 1.50 48.00 1.83 0.16 9

3.00 48.00 1.83 0.12 8
6.00 47.00 1.89 0.08 19
9.00 41.00 1.99 0.02 23
12.00 41.00 1.98 0.00 27
15.00 35.00 2.08 0.00 32
18.00 36.00 2.07 0.00 32.5
21.00 36.00 2.09 0.00 33
25.50 35.00 2.10 0.00 33

03. 1.50 47.00 1.86 0.18 14

3.00 46.00 1.90 0.17 19
6.00 47.00 1.88 0.09 20
9.00 40.00 1.99 0.03 26
12.00 40.00 2.01 0.00 30.5
15.00 37.00 2.05 0.00 32
18.00 35.00 2.08 0.00 33

04. 1.50 46.00 1.86 0.18 10

3.00 48.00 1.83 -- --
6.00 43.00 1.95 0.07 23
9.00 38.00 2.03 0.03 30
12.00 36.00 2.08 0.00 33
15.00 36.00 2.10 0.00 33.5
18.00 34.00 2.12 0.00 34
21.00 34.00 2.11 0.00 34
25.50 30.00 2.17 0.00 35

Contd.
IIT GUWAHATI SHEET NO.: 15

B.H. No Depth Porosity. Saturated “C” “”

(M) (%) density gm/cc. Kg/Cm2 Degree

05. 1.50 47.00 1.87 0.21 11

3.00 48.00 1.85 0.18 9
6.00 41.00 1.98 0.04 26
9.00 41.00 1.99 0.00 30
12.00 39.00 2.01 0.00 31
15.00 39.00 2.04 0.00 31.5
18.00 35.00 2.09 0.00 32
21.00 36.00 2.07 0.00 32
24.00 34.00 2.11 0.00 33
27.00 32.00 2.14 0.00 34
30.00 31.00 2.17 0.00 35

06. 1.50 47.00 1.86 0.20 10

3.00 45.00 1.90 0.17 15
6.00 43.00 1.95 0.07 24
9.00 37.00 2.05 0.02 28
12.00 39.00 2.02 0.00 31
15.00 40.00 2.00 0.09 26
18.00 35.00 2.09 0.00 32.5
21.00 33.00 2.12 0.06 33
24.00 31.00 2.15 0.08 35

07. 1.50 49.00 1.84 0.16 8

3.00 50.00 1.79 -- --
6.00 44.00 1.94 0.10 19
9.00 42.00 1.97 0.04 26
12.00 40.00 2.06 0.07 30
15.00 38.00 2.03 0.00 32
18.00 37.00 2.06 0.00 32
21.00 34.00 2.12 0.00 35

08. 1.50 47.00 1.86 0.18 12

3.00 47.00 1.88 0.13 17
6.00 43.00 1.95 0.02 23
9.00 42.00 1.97 0.00 30
12.00 38.00 2.04 0.00 31
15.00 40.00 2.01 0.03 30
18.00 40.00 2.03 0.00 31.5
21.00 34.00 2.12 0.00 34
24.00 35.00 2.08 0.00 32
28.50 32.00 2.13 0.00 34

Contd.
IIT GUWAHATI SHEET NO.: 16

B.H. No Depth Porosity. Saturated “C” “”

(M) (%) density gm/cc. Kg/Cm2 Degree

09. 1.50 47.00 1.84 0.16 8

3.00 47.00 1.83 0.15 7
6.00 45.00 1.92 0.04 18
9.00 43.00 1.96 0.00 23
12.00 43.00 1.94 0.00 25
15.00 37.00 2.06 0.00 32
18.00 36.00 2.08 0.00 32.5
21.00 38.00 2.04 0.18 32
24.00 33.00 2.11 0.10 34
27.00 31.00 2.15 0.00 35

10. 1.50 47.00 1.84 0.18 8

3.00 47.00 1.85 0.17 10
6.00 41.00 1.98 0.03 25
9.00 38.00 2.03 0.00 31
12.00 42.00 1.97 0.08 23
15.00 36.00 2.07 0.00 32
18.00 36.00 2.09 0.00 32
21.00 32.00 2.14 0.00 35
25.50 31.00 2.15 0.00 36

11. 1.50 42.00 1.92 0.21 10

3.00 48.00 1.83 -- --
6.00 43.00 1.96 0.07 25
9.00 37.00 2.06 0.03 31
12.00 36.00 2.08 0.00 32
15.00 35.00 2.09 0.00 32.5
18.00 36.00 2.08 0.00 32
21.00 33.00 2.12 0.00 35
24.00 33.00 2.14 0.00 34
27.00 31.00 2.15 0.10 35.5
30.00 31.00 2.15 0.09 35

Contd.
IIT GUWAHATI SHEET NO.: 17

ATTERBERG’S LIMIT TEST

B.H. No Depth (M) Liquid Limit Plastic Plasticity

(%) Limit (%) Index (%)

01. 1.50 29.50 NP NP

3.00 33.60 24.84 8.76

02. 1.50 31.70 24.58 7.12

3.00 28.60 23.75 4.85

04. 1.50 29.10 NP NP

3.00 42.60 26.75 15.85

07. 3.00 45.20 26.49 18.71

09. 1.50 28.70 NP NP

3.00 49.10 26.38 22.72

10. 1.50 29.20 23.46 5.74

3.00 33.50 24.74 8.76

11. 1.50 31.10 24.35 6.75

3.00 27.90 NP NP

Contd.