Series 240

Type 3351 Pneumatic On/off Valve

Application
Tight-closing on/off valve for liquids, gases and vapors
according to DIN or ANSI standards
Valve size DN 15 to 100 · NPS ½ to 4
Pressure rating PN 10 to 40 · Class 150 and 300
Ambient temp. –35 to +100 °C · –30 to +212 °F
Medium temp. –50 to +250 °C · –58 to +482 °F

The Type 3351 Pneumatic Control Valve consists of an on/off

valve and a pneumatic actuator. Optionally, the valve can be
equipped with a bellows seal or insulating section.
Valve body made of:
•• Cast iron
•• Spheroidal graphite iron
•• Cast steel
•• Cast stainless steel

Special features
•• Soft-seated valve plug
•• Leakage class VI according to IEC 60534‑4 or class VI
according to ANSI/FCI 70-2
•• Attachment of solenoid valves and limit switches according
to IEC 60534-6 and NAMUR recommendation. Refer to In-
formation Sheet u T 8350 for more details.

Versions
Fig. 1: Type 3351 Pneumatic On/off Valve
Standard version for pressure rating PN 10 to 40 or
Class 150 and 300, fail-close or fail-open
–– Type 3351 (Fig. 1) · On/off valve with self-adjusting PTFE
V-ring packing · Valve size DN 15 to 100 (NPS ½ to 4)
Medium temperatures from –10 to 220 °C (14 to 428 °F)
–– Type 3351 with bellows seal · On/off valve with bellows
seal and PTFE V-ring packing · Valve size DN 15 to 50
(NPS ½ to 2) · Medium temperatures according to Table 1
–– Type 3351 with insulating section · On/off valve with in-
sulating section and plug stem sealed by a PTFE V-ring
packing · Valve size DN 15 to 50 (NPS ½ to 2) · Medium
temperatures according to Table 1

Further versions
–– Additional handwheel
–– Reinforced spring
–– Higher or lower medium temperatures
–– Higher ambient temperatures

Fig. 2: Type 3351 Pneumatic On/off Valve · Version with hand-

wheel

Associated Information Sheet T 8000-X Edition February 2014

Associated Data Sheets for
pneumatic actuators T 8310-1, T 8310-2 Data Sheet T 8039 EN
Principle of operation
Depending on the type of valve seat and the arrangement of
the valve plug, the valve has two different fail-safe actions
which are used when the pressure acting on the diaphragm is
reduced or when the control signal fails:
–– Fail-close action: the valve is closed upon supply air fail-
ure.
–– Fail-open action: the valve is opened upon supply air fail-
ure.

Direction of flow
The direction of the medium flow in the valve depends on the
process medium and the selected fail-safe action.
For fail-close valves which are used to control gases and va-
pors, the medium must flow in the closing direction (A  B),
except for the DN 100 version, in which the medium must
flow into the plug in the opening direction (B  A).
For control applications with liquids, the medium must flow
into the plug in the opening direction (B  A).
In fail-open valves, all media must flow in the opening direc-
tion (A  B). For versions with the optional handwheel, a fail- A B

close valve can be opened and a fail-open valve can be

closed in the event of supply air failure.

Fig. 4: Type 3351 Pneumatic On/off Valve with handwheel

A B

Fig. 3: Detailed drawing of the insulating section

Fig. 5: Type 3351 Pneumatic On/off Valve · Version with bellows

2 T 8039 EN
Table 1: Technical data
Version DIN ANSI
Spheroidal Cast stainless
Cast iron Cast steel Cast stainless Cast steel
Body material graphite iron steel A351
EN-JL-1040 1.0619 steel 1.4408 A216 WCC
EN-JS-1049 CF8M
Pressure rating PN 10, 16 PN 10, 16, 25 PN 10, 16, 25, 40 Class 150 and 300
Standard DN 15 to 100 NPS ½ to 4
Valve
size Bellows seal/
DN 15 to 50 NPS ½ to 2
insulating section
Connecting flanges Form B according to Form B1 according to
RF
DIN EN 1092-2 DIN EN 1092-1

Temperature ranges in °C (°F) · Permissible operating pressures according to pressure-temperature diagrams (see Information Sheet u T 8000-2)
Ambient temperature –35 to +100 °C (–30 to +212 °F) –35 to +100 °C (–30 to +212 °F)
Medium temperature
–10 to +220 °C (14 to 428 °F) –10 to +220 °C (14 to 428 °F)
(standard)
High-temperature version 2) –10 to +240 °C (14 to 464 °F) 1) –10 to +240 °C (14 to 464 °F) 1) 4)
–29 to +220 °C –50 to +220 °C
–50 to +220 °C
Low-temperature version – (–20 to (–58 to
(–58 to +428 °F) 3) 4)
+428 °F) 4) +428 °F) 3) 4)
Leakage class IEC 60534-4: VI ANSI/FCI 70-2: Class VI
1) With soft-seated special plug and bellows seal or insulating section
2) Higher temperatures (max. 450 °C/84 °F) with metal-seated plug and leakage class IV or V on request
3) Additional impact test certification required between –29 °C (–20 °F) and –50 °C (–58 °F)
4) With bellows seal or insulating section only

Table 2: Materials
Valve DIN ANSI
Spheroidal Cast stainless Cast stainless
Cast iron Cast steel Cast steel
Body graphite iron steel steel A351
EN-JL-1040 1.0619 A216 WCC
EN-JS-1049 1.4408 CF8M
Seat 1.4006 1.4404/1.4571 A182 F6a Cl. 2 316Ti/316L
Plug 1.4404 · Seal made of reinforced PTFE
Body gasket Graphite on metal core
NBR (nitrile butadiene rubber) with fabric reinforcement
Actuator diaphragm
Materials for higher or lower ambient temperatures on request
Standard version

Valve cover Valve cover

Spheroidal Spheroidal
Cast steel 1.4571/1.4404 Cast steel A216 316L welded to
Valve bonnet graphite iron graphite iron
1.0619 welded to WCC bonnet
EN-JS-1049 EN-JS-1049
bonnet 1.0619 A216 WCC

Guide bushing 1.4104 1.4404 1.4104 316L

Packing V-ring packing: PTFE with carbon · Spring: 1.4310
Threaded bushing assembly 1.4404 + Carbon 316L + Carbon
Version with bellows seal or insulating section
Bellows seal/insulating
1.0460 1.4404 A105 316L
section
Cast iron Cast steel Cast steel
Actuator flange
EN-JL-1040 1.0619 A216 WCC
Guide bushing Fiber-reinforced plastic
Bellows seal: Bellows 1.4571 and PTFE/graphite V-ring packing · Spring 1.4310
Seal
Insulating section: PTFE/graphite V-ring packing · Spring 1.4310
Guide nut assembly 1.4404 and fiber-reinforced plastic 316L and fiber-reinforced plastic
Flange of bellows seal or
1.0460 1.4301 A105 304
insulating section

T 8039 EN 3
Table 3: Control pressure and maximum differential pressure · All pressures in bar and psi
Valve size DN 15 20 25 32 40 50 65 80 100
(bellows seal or insulating section up to
NPS ½ ¾ 1 – 1½ 2 2½ 3 4
DN 50/NPS 2)
KVS 6.3 10 14 25 31 40 72 90 170
Flow coefficient
CV 7.5 12 16 – 36 47 84 105 200
Actuator area in cm² 60 186 255 700
Pneumatic actuator
Travel in mm 8 10 12.5 30
Max. supply pressure 6 bar/88 psi
Standard version
Fail-close
Min. control pressure to open the valve at
4 bar/58 psi
Δmax

Vapors, gases A  B 20 bar/290 psi 16 bar/235 psi 10 bar/145 psi 10 bar

Max. perm. differen-
tial pressure Δpmax at Liquids B  A 16 bar/235 psi 10 bar/145 psi 5 bar/73 psi 145 psi

Fail-open

Min. control pressure to close the valve at 4 bar/

4.5 bar/65 psi
Δpmax 58 psi

Max. permissible differential pressure Δpmax

20 bar/290 psi 16 bar/235 psi 10 bar/145 psi
for vapors, gases or liquids

Special version for fail-close version for higher differential pressure Δp

Min. control pressure to open the valve at Δpmax 5.5 bar/80 psi –
Max. permissible differential pressure Δpmax
30 bar/435 psi 20 bar/290 psi 7 bar/102 psi –
for vapors, gases or liquids 1)
1) For direction of flow B  A (see Fig. 4)

Table 4: Dimensions for Type 3351 (see Fig. 6)

DN 15 20 25 32 40 50 65 80 100
Valve
NPS ½ ¾ 1 – 1½ 2 2½ 3 4
PN 10/40 mm 130 150 160 180 200 230 290 310 350
in 7.25 – 8.75 10 10.88 11.75 13.86
Class 150
Length L mm 184 – 222 254 276 298 352
in 7.50 7.63 7.75 – 9.25 10.50 11.50 12.50 14.49
Class 300
mm 191 194 197 – 235 267 292 318 368
Diaphragm ØD mm 150 240 280 390
Control pressure
a G 1/4 G 1/4 G 3/8
connection
Standard version
H1 mm 260 285 328 485
H2 mm 45 72 98 118
H3 1)
mm 380 380 415 565
Version with bellows seal or insulating section
H4 mm 400 415
H2 mm 55 80 –
H3 1) mm 520 535
1) Minimum clearance to remove the actuator; version with handwheel: up to DN 80: +150 mm, DN 100: +210 mm

4 T 8039 EN
Table 5: Weights for Type 3351

DN 15 20 25 32 40 50 65 80 100
Standard version
NPS ½ ¾ 1 – 1½ 2 2½ 3 4
PN 10/40 11 12 12 25 26 29 48 52 70
Weight, approx. kg Class 150 11 12 13 – 23 27 47 52 64
Class 300 12 13 14 – 25 29 50 55 64
Version with bellows seal or insulating section
PN 10/40 16 17 17 33 34 37
Weight, approx. kg Class 150 16 17 18 – 31 35 –
Class 300 17 18 19 – 33 37

Ordering text

Type 3351 Pneumatic On/off Valve

260 Valve size DN/NPS
ØD
ØD Nominal pressure PN/Class
a
Body material According to Table 1
169 Fail-safe position Fail-close or fail-open
a
Control air pressure … bar
H3 H3
Handwheel With/without
H4
Special version Bellows seal/insulating section
High or low-temperature version
H1
Valve accessories Solenoid valve and/or electric or
pneumatic limit switch
A B A B
H2 H2

L L

Type 3351
With handwheel With bellows seal or insulating
section
Fig. 6: Dimensional drawing of Type 3351

T 8039 EN 5
6 T 8039 EN
T 8039 EN 7
Specifications subject to change without notice
2015-04-14 · English

SAMSON AG · MESS- UND REGELTECHNIK

Weismüllerstraße 3 · 60314 Frankfurt am Main, Germany
Phone: +49 69 4009-0 · Fax: +49 69 4009-1507
[email protected] · www.samson.de T 8039 EN