Date of Issue 2003/09/15
Product HES Office
HES
HES
B 117-03
C REV6
FLANGE NUTS
1. SCOPE
This standard specifies the standard flange nut.
Remarks: The units and numerical values in this standard are specified values in accordance with the
International System of Units (SI), and those in { } are specified values based on customary units.
PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com
2. SHAPE, DIMENSIONS AND FINISH
The shape, dimensions and finish shall conform to Table 1.
Table 1
12.5S Thread
D2
H
30 (apprx.) B
t
Apprx.90
Apprx.120
MD x P
C
D1
30
h
(Apprx.)
a b
1 Max.
1 Max.
Eccentricity of Inclination of bearing Inclination of
bolt hole surface flats
Unit: mm
h t C D1 a-b
DxP H B D2
min. min. min. Apprx. Max.
(4 x 0.7) 5.0 11
3.3 0.9 8 0 8.9 7.8
5 x 0.8 5.5 ±0.15 12 0.3
-0.2 0
6 x 1.0 6.0 4.0 10 11.1 13 9.8
1.2 -0.4
8 x 1.25 7.5 5.0 12 13.5 17 11.5
0.4
10 x 1.25 9.0 6.0 1.5 14 0 15.5 19 13.5
±0.2
-0.25 0
12 x 1.25 11.0 7.0 2.0 17 18.9 24 16.5 0.5
-0.5
Remarks: The 4 x 0.7 flange nut in ( ) should not be used, if possible.
PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com
3. MATERIAL AND MECHANICAL PROPERTIES
The material and mechanical properties for the nuts shall conform to Table 2.
Table 2
Material SWRCH10 to 15R
Proof Load Stress
2
N/mm 784.5{80} Min.
2
{kgf/mm }
(Reference)
80 Min.(*1)
Hardness (HRB)
Note (*1): If hardness is employed as a simplified method, agreement between the supplier and the
purchaser shall be required.
Remarks: SWRCH material shall conform to JIS G 3507 (Carbon steel wire rods for cold heading and
cold forging).
4. SURFACE TREATMENT
The surface treatment for the nuts shall conform to Table 3.
Table 3
Code 0 8 2 7 (*2)
Surface Treatment MFZn2-B MFZn2-C MFCr2 MFZn2-K
Note (*2): The use shall be avoided, if possible.
Remarks: Plating shall conform to HES D 2003 {ELECTROPLATING (FOR CORROSION
PREVENTION, RUST PREVENTION AND DECORATION)}.
5. THREADS
a) Threads of nuts shall conform to HES A 1003 (SCREW THREADS) and accuracy shall be 6H.
b) When plating threads, accuracy of threads before plating shall be 6H.
6. APPEARANCE
Surface roughness shall conform to the specifications of Section 2. In addition, there shall be no cracks,
flaws, burrs, rust or other detrimental defects.
7. INSPECTION
Inspection shall be performed in accordance with JIS B 1181 (Hexagon nuts and hexagon thin nuts).
PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com
8. DESIGNATION AND PART NUMBER
Designation: NUT, FLANGE, D mm
Example: NUT, FLANGE, 6 mm
Part number:
9 4 0 5 0 0 0
D Surface treatment
Remarks: When D has less than the specified digits, add 0 to the head of the numeral code.
Example: D = 6 06
NUT, FLANGE, 6 mm 94050-06080
9. DRAWING INDICATION
When specifying parts covered in this standard, no part drawing is required.
Applicable standards
HES A 1003-03 SCREW THREADS
HES D 2003-03 ELECTROPLATING (FOR CORROSION PREVENTION, RUST PREVENTION
AND DECORATION)
JIS B 1181 : 01 Hexagon nuts and hexagon thin nuts (Amendment)
JIS G 3507 : 91 Carbon steel wire rods for cold heading and cold forging
PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com
Revision Record
Year Rec Issue NewsNo Prep Conf Appvl Remarks
76 EST 76/02/12 76002 Shimazaki Shimane Endo
76 REV1 76/03/15 76004 Shimazaki Shimane Endo
76 REV2 76/09/21 ----- Shimazaki Shimane Endo Rewritten by new drawing method
83 REV3 83/11/17 83016 Goudo Tomino Ota
87 REV4 87/12/02 87024 Tashiro Goudo Katagiri Addition of surface treatment (code)
87 Rewrite 91/08/19 91017 Oooka Goudo Morita Introduction of SI 2nd stage
93 REV5 93/03/08 93003 Tashiro Goudo Morita Change of materials
93 Rewrite 95/03/09 ----- Tanaka Shimada Yamada Data transfer to PC
93 Rewrite 98/06/30 ----- Tashiro Shimada Honda Data transfer to Notes DB
99 Correction 99/08/12 99011 Tomonaga Naya Tomino Correction of errors
03 REV6 03/09/15 03015-36 Okada Tomino Suganuma Change to ISO class
PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com
