Scribd
Upload
359 views2 pages

MDF Data Sheet

Uploaded by

rmbardollo07
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
359 views2 pages

MDF Data Sheet

Uploaded by

rmbardollo07
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

QUALITÄTSMANAGEMENT ISO 9001 Coding TDGR500EN

Revision 00
Page Page 1 of 2

TECHNICAL DATA SHEET

EGGER MDF-ST E1

Recipe: 500
Application: Base particle board for interior fitments (including furniture) for use
in dry conditions.

Board type meets EN 622-5 standard

Mechanical properties
Unit Board thickness
thickness
Board mean values
[mm] >6 - 9 >9 - 12 >12 - 19 >19 - 30 >30 - 40
Density [kg/m3] plant specific

Internal Bond strength EN 319 [N/mm2] >0,72 >0,72 >0,67 >0,67 >0,54

Bending strength EN 310 [N/mm2] >40 >35 >31 >26 >22

Modulus of elasticity EN 310 [N/mm2] >3000 >2800 >2700 >2600 >2400


Swelling in thickness 24h EN 317 [%] <15 <13 < 10 <8 <7
Surface soundness EN 311 [N/mm2] >1,0
Screw withdrawal surface [N] >1080 >1080 > 1080
Screw withdrawal edge [N] >900 >810 >750
Sand content [%] <0,02
Moisture content *1 EN 322 [%] 6±2
Surface absorption [mm] >210
Formaldehyde content *2 EN 120 [mg/100g] E1

General tolerances Unit Board thickness

[mm] >6 - 9 >9 - 12 >12 - 19 >19 - 30 >30 - 40


Length tolerance EN 324 [mm] ±2,0mm/m, maximum ±5,0
Width tolerance EN 324 [mm] ±2,0mm/m, maximum ±5,0
Squareness EN 324 [mm/m] ≤2,0
Edge straightness EN 324 [mm/m] ≤1,5
Thickness tolerance EN 324 [mm] ±0,2 ±0,2 ±0,2 ±0,3 ±0,3
Standard sanding K150

Responsible: PM chipboard/MDF/EUROLIGHT Release date: 30.05.2010


QUALITÄTSMANAGEMENT ISO 9001 Coding TDGR500EN
Revision 00
Page Page 2 of 2

Building physical properties Unit Board thickness


[mm] >6 - 9 >9 - 12 >12 - 19 >19 - 30 >30 - 40
Fire behaviour category
Board thickness < 9 mm class E
Board thickness ≥ 9 mm and
density ≥ 600 kg/m³ in line with EN 13986 D-s2, d0
Water vapour diffusion resistance value EN 13986
µ moist µ dry
Mean density 600 kg/m3 12 20
Mean density 800 kg/m3 20 30
Thermal conductivity EN 13986
Mean density 600 kg/m3 W/(m·K) 0,10
Mean density 800 kg/m3 0,14

Air sound insulation EN 13986


EN 13986 R = 13 x lg(mA) + 14
(mA = board surface weight kg/m²)

Sound absorption EN 13986


Frequency range
250 Hz bis 500 Hz 0,10
1000 Hz bis 2000 Hz 0,20
Biological durability EN 13986
EN 335-3 Harzard category 1
(no earth contact , dry 20o/65% relative humidity)

PCP content EN 13986


EN 13986 [ppm]
<5

*1 On delivery

*2 Formaldehyde content
According to the “Regulation on the Prohibition of Chemicals (ChemVerbotsV)” annex to § 1, clause 3 from 14 th October, 1993 in connection with the publication of the BGA in
the federal health sheet 10/91 (s. 487-489) about “testing method for particleboard”, uncoated MDF board must not exceed a perforator limit value (photometrical) of 8 mg
HCHO/100g over-dry board at moisture content of 6,5 %. The flexible half-years mean value is max. 7 mg HCHO/100g over-dry board.

Provisional note:
This technical data sheet has been carefully drawn up to the best of our knowledge. We accept no liability for any mistakes, errors in standards or printing errors. In addition,
technical modifications can result from the continuous further development, as well as from changes in standards and documents originating from statutory bodies. The
contents of this technical leaflet should therefore not be considered as instructions for use or as legally binding.

Responsible: PM chipboard/MDF/EUROLIGHT Release date: 30.05.2010

You might also like