Scribd
Upload
96 views3 pages

HVAC Design Using HAP

Designing purpose need grill sizes with cubic feet per minute

Uploaded by

batthulavishal7842
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
96 views3 pages

HVAC Design Using HAP

Designing purpose need grill sizes with cubic feet per minute

Uploaded by

batthulavishal7842
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Heating, Ventilation & Air Conditioning

(HVAC) Design using HAP


Instructor-Led Online Training
Course Curriculum (Duration: 40 Hrs)

Chapter 1: Introduction to HVAC

 What is HVAC?
 Understanding Sensible Heat, Latent Heat and Enthalpy
 Standards and codes used in HVAC

Chapter 2: Modes of Heat Transfer

 Conduction
 Convection
 Radiation

Chapter 3: Refrigeration Cycles

 Basic Refrigeration System or Vapor Compression Cycle


 Types of Compressors, Condenser, Expansion Valve & Evaporator Coil,
 Temperature TON of Refrigeration
 Commonly used metrics, units and conversions

Chapter 4: Psychometrics

 Psychometrics definition
 Dry Bulb Temperature
 Wet Bulb Temperature
 Dew point Temperature
 Relative Humidity
 Humidity Ratio
 Processes
 Heating
 Cooling
 Cooling and Dehumidification
 Heating and Humidification
 Finding Values Using the Chart (Manually and using software)

1
Chapter 5: Types Air-Conditioning System and Equipment

 Window A/C
 Split A/C
 Ductable Split A/C
 Variable Refrigerant Volume (VRV)/Variable Refrigerant Flow (VRF)
 Ductable Package A/C
 Package Roof Top Units
 Central Plant Chilled Water System

Chapter 6: Comfort Conditions and Cooling Load Calculations

 Comfort Parameters
 Understanding Indoor & Outdoor Design Conditions
 Cooling load calculation methods
 Calculation of U values
 Sources of Heat Gain
 External :
 Heat Gain through Glass/Window
 Heat Gain through Roof/Wall/ Wall Partition gain
 Internal:
 Heat Gain through People, Lights, Electrical Equipments, Motors, Kitchen
Appliances
 Heat gain through Infiltration air
 Heat gain through Ventilation
 ESHF, ADP & Air Flow Rate(CFM) Calculation
 Cooling load calculation manually using E-20 form
 Cooling load calculation using HAP (Hourly Analysis Program)

Chapter 7: Air Distribution System- Ducting and Air Terminals

 Duct-Definition & Terminology


 Types of Ducts, Duct fittings, Dampers, Flexible ducts
 Classification of Duct(Low, Medium & High pressure)
 Selection of Duct Gauges & thickness
 Comparison between different shapes of duct, Duct Fabrication, Insulation &
Installation procedure
 Type of Duct Materials, Calculation of total sheet required for Duct Fabrication &
Estimating duct weight in kgs
 Ducts-Sizing
 Selection of Grills and Diffusers
 Duct designing methods (Manually)
 Velocity reduction method.
 Equal friction Method.
 Static regain method
 Fan selection & ESP calculation.
 Components of Air Distribution System
 Concept of CAV & VAV

2
Chapter 8: Design of Ventilation system

 Fresh Air Handling Unit Designing as per ASHRAE 62.1


 Restaurant/Residence kitchen ventilation system designing as per ASHRAE 90.1
 Non Central and Central Toilet Exhaust Calculations as per ASHRAE 62.1
 Car Parking Ventilation system Designing

Chapter 9: Refrigerants

 Types of refrigerant
 Evaporating & condensing properties of refrigerant
 Refrigerant Pipe sizing methods

Chapter 10: Chilled Water Distribution System

 Chilled water system components


 Various types of Chillers
 Chilled water pipe sizing as per ASHRAE standards
 Typical Installation of Chilled water FCU and AHU
 Valves and accessories used in Chilled water system
 District cooling system

Chapter 11: Pumps Design

 Pump classifications
 Selection of Pump
 Pump Head Calculation

Chapter 12: Cooling Tower

 Types of cooling tower


 Cooling tower water losses
 Cycles of concentration
 Cooling tower selection

Chapter 13: SOFTWARES

 Load calculation using Hourly Analysis Program (HAP)


 Calculation of duct sizes by McQuay Duct sizer
 Calculation of Chilled water pipe sizes by McQuay pipe sizer Software
 Psychometry Software
 Air terminal (Grills, Diffusers, Registers, LBG-Linear Bar Grills, SLSD-Supply
Linear Slot Diffuser) selection by using BETA Program

IFS Academy
Phone: +91-20-2543 0338, Mob. No.: +91-98228 49628, Email: [email protected]
Visit Us At: www.ifsacademy.org

You might also like