OWNER'S MANUAL

PLEASE READ CAREFULLY BEFORE USING AND KEEP WELL.

7" DIGITAL WATERPROOF LCD MONITOR

FOR HEAVY DUTY INDUSTRY

Model: ECL-750WP
Design and Specifications are subject to change without notice.
r OWNER'S RECORD

Model No. ECL-750WP

Serial No.

WARNING

No!

2
r SUGGESTIONS

7" DIGITAL WATERPROOF LCD MONITOR

FOR HEAVY DUTY INDUSTRY

1 Safety
- Use only DC 10V ~ DC 32V.
- In case that dust or liquid was soaked into the case, please turn off
power and consult an experienced technician before using.

2 Installation
- Do not install the unit in an extremely hot or humid place
(radiator, air duct, etc.) or in a place subject to direct sunlight,
excessive dust, mechanical vibration or shock.
- If your vehicle has been parked in direct sun light resulting in
a considerable rise in temperature inside the vehicle, allow the unit
to cool off before operating.

3 General cleaning information

- Clean the unit with a slightly damp soft cloth.
Use a mild household detergent.
Never use strong solvents such as thinner or benzine as they
might damage the finish of the unit.

3
r FEATURES
- Water Resistance (IP68)
- 7" Digital LCD Wide Panel
- Auto NTSC/PAL Detection
- Auto DAY/NIGHT Detection
- Vandal Resistance (Al Housing)
- Parking Distance Marker Setting Available
- Capacitive Touch Key
- Support Multi-Functional Camera (CAM1 &CAM2):
Normal/Shutter/Tilt

r PACKAGE CONTENTS
Please check that you have the correct contents before using this product.
If any items are missing, please contact your dealer.

(SCREW TYPE)

OR

(RAIL TYPE)
ECL-750WP MONITOR SUNVISOR STAND BRACKET
OPTIONAL

OWNER'S MANUAL
PLEASE READ CAREFULLY BEFORE USING AND KEEP WELL.

MULTI CONTROL BOX

FOR REAR VISION MONITOR

or
CA1

CA2
CA1

CA2

Model: ECL-750WP

4P IP TYPE 4P DIN TYPE

Design and Specifications are subject to change without notice.

CAMERA CONNECTOR CAMERA CONNECTOR

INSTRUCTION
POWER CORD SCREW KITS MANUAL

4
r OPERATIONS

4
1 POWER
5
2 SELECT

3 MENU
6
4 UP

5 DOWN

6 DAY/NIGHT SENSOR
(CDS)

1 POWER
Touch to turn the monitor on.

Touch to turn the monitor off.

2 NOTE Monitor start mode will follow “AUTO POWER SETTING”

2 SELECT

Touch SEL to select CAMERA.

SEL
Touch SEL to select the option in SET UP MENU.

3 MENU

Use MENU to enter Display Menu(Short key) and

Main Menu(Long key).
Touch once to enter menu mode.
MENU Touch again to exit from menu mode.
Selectable OSD Menu Disappears within 7 sec if there’s
no new button pressed.
Touch menu button over 2 sec to go back to main menu
from submenu.

5
r OPERATIONS

4 UP 5 DOWN

While in Menu mode and navigate though

the available menu options.
Touch to adjust Bright, Contrast, Color, Tint
Volume and other setting values.

6 DAY/NIGHT SENSOR (CDS)

Automatic Brightness Control

The brightness of the monitor is adjusted automatically
with the CDS accordingly to the circumstance.

6
r OPERATIONS

. DISPLAY MENU

MENU SEL SEL

MENU UP / DN SELECT UP / DN SELECT

Short Key
DN Option setting
(more than 0.5 sec)

DISPLAY MENU BRIGHT 30

(0~60)
BRIGHT 30
CONTRAST 30
COLOR 30 CONTRAST 30
TINT 30 (0~60)

COLOR 30
(0~60)

PAL MODE NTSC MODE

TINT 30
(0~60)

* TINT menu is displayed in NTSC only.

2 NOTE User can adjust Display setting value for CAM1 and CAM2
channel separately.

7
r OPERATIONS

. SETUP MENU
Touch M E N U b u t t o n f o r a w h i l e (over 2 sec) to enter MAIN MENU.
Selectable OSD MENU disappears within 7 sec if there is no new button pressed.

A
MAIN MENU
MENU SEL 1. CAMERA SETTING
2. TRIGGER SETTING
MENU UP / DN SELECT 3. AUTO SCAN SETTING
lo n g k ey 4. DAY/NIGHT SETTING
(more th a n 2 sec) up / down shifting option setting 5. ADVANCED MENU

1 CAMERA SETTING
NOR/MIR : [MIRROR;NORMAL]
1. CAMERA SETTING
UP/DOWN : [UP;DOWN]
C A M 1 NOR/MIR : [MIRROR;NORMAL]
NAME : [CAM1 ]
C A M 2 UP/DOWN : [U P ; D O W N ]
NAME:[CAM1 ] CAM1,CAM2 UP / DN
A
SORT:[NORMAL;SHUTTER;
TILT.AT;TILT.MT]
SEL SEL SEL MENU
Camera’s mirror/normal image can be SELECT UP / DN SELECT UP / DN SELECT MENU
changed (CAM1/CAM2 separate control).
selecting shifting option setting name setting shifting exit
Camera’s up/down image can be
SORT:[NORMAL;SHUTTER;TILT.AT;TILT.MT]
changed (CAM1/CAM2 separate control).
Different types of camera CAM1,CAM2 UP / DN
A
(Normal/Shutter/Tilt) can be connected to
CAM1/CAM2.
SEL SEL MENU
Each camera can be named and the
SELECT UP / DN SELECT MENU
selected camera name is displayed
via OSD. selecting shifting option setting exit

2 NOTE Select camera type between NORMAL, SHUTTER,

TILT AUTOMATIC or TILT MANUAL.
How to control TILT MANUAL:
Select “TILT.MT”. Get out from MENU.
Press MENU key two times and you can see below OSD.
TILT CONTROL:
Press key for TILT UP.
Press key for TILT DOWN.

8
r OPERATIONS

2 TRIGGER SETTING
SOURCE:[CAM1;CAM2;SKIP]
2. TRIGGER SETTING
Trigger1,Trigger2
A UP / DN
TRIGGER1 SOURCE:[CAM1;CAM2;
SKIP]
TRIGGER2
DELAY:[0~20sec]
SEL SEL MENU
MARKER:[TYPE1;OFF]
SELECT SELECT MENU
MARKER SETTING
selecting option setting exit
User can use 2 triggers and each trigger source(CAM1;CAM2;SKIP) can be selected.
When the trigger is activated, the selected source’s image is displayed.

2 NOTE Priority of trigger when triggers are engaged at the same time:Trigger1>Trigger2
DELAY:[0~20SEC]

Each trigger's delay time is adjustable from 0 sec to 20 sec.

Trigger1,Trigger2
2 NOTE Delay time setting is only
available with SELECT
SEL .
A UP / DN

If one camera is activated

by an intermittent signal MENU
SEL SEL
( e.g. from an indicator light’s )
SELECT UP / DN SELECT MENU
the delay must be activated to
selecting shifting option setting exit
prevent the picture from flickering.

MARKER:[TYPE1;OFF]
TYPE1
Trigger1, Trigger2
A UP / DN
LEFT-RIGHT UP-DOWN WIDTH

SEL SEL MENU

LEFT-RIGHT UP-DOWN WIDTH
SELECT UP / DN SELECT MENU
selecting shifting option setting exit

MARKER SETTING LEFT-RIGHT UP-DOWN

TYPE1
A

SEL SEL SEL MENU

SELECT UP / DN SELECT UP / DN SELECT UP / DN MENU

selecting shifting selecting shifting option setting selecting exit

2 NOTE If “MARKER”is set as”OFF”,

Parking aid marker is not displayed when the reverse gear is engaged.

9
r OPERATIONS

3 AUTO SCAN SETTING

3. AUTO SCAN SETTING AUTO SCAN:[ON;OFF]

AUTO SCAN:[ON;OFF] A
CAM1 DELAY:[0~20sec]
CAM2 DELAY:[0~20sec]
SEL MENU
UP / DN SELECT MENU
CAM1 DELAY
shifting option setting exit
CAM2 DELAY

SEL SEL MENU

UP / DN SELECT UP / DN SELECT MENU
shifting option setting shifting option setting exit

2 NOTE Auto scanning time of each camera can be adjusted from 0 sec to 20 sec.
Auto scan delay time setting is only available with SELECT
SEL .
To give a pause while scanning, press SELECT
SEL
.
When user select “ 0 sec ”for one channel, monitor skip scanning the channel.

4 DAY/NIGHT SETTING
4. DAY/NIGHT SETTING SENSOR:[ON;OFF]

SENSOR: [ON;OFF] A
SENSITIVITY:[0~60]
NIGHT BRIGHT:[0~60]
SEL MENU
UP / DN SELECT MENU
SENSITIVITY:[0~60]
shifting option setting exit
NIGHT BRIGHT:[0~60]
A

SEL SEL MENU

UP / DN SELECT UP / DN SELECT MENU User can set the level of “Day/Night sensor
shifting option setting shifting option setting exit sensitivity” and “night bright”.

10
r OPERATIONS

5 ADVANCED MENU
6. ADVANCED MENU AUTO POWER:[OFF;ON;AUTO]
A
AUTO POWER:
[OFF;ON;AUTO]
FACTORY RESET
SEL MENU
UP / DN SELECT MENU

FACTORY RESET shifting option setting exit

SEL
UP / DN SELECT

shifting option setting

2 NOTE “AUTO” Setting: Monitor keeps the last setting in memory:

Monitor will start up “Power-on” mode or “Stand- by”mode according
to its last mode before the ignition key off.
“OFF” Setting: Monitor keeps “Stand- by”setting regardless of the last mode
before the ignition key off.
“ON” setting: Monitor will be turned on automatically when ignition key on
regardless of the last mode of the monitor before the ignition key off.

11
r INSTALLATION
1 DASH BOARD SCREW MONITOR

1-1. STAND BRACKET(SCREW FIXING TYPE)

1-2. STAND BRACKET(RAIL TYPE)

2 SUNVISOR MONITOR

12
r SYSTEM CONNECTIONS

POWER/TRIGGER WIRE FUNCTIONS

REF # WIRE COLOR DESCRIPTION

1 WHITE TRIGGER2
2 GREEN TRIGGER1
3 BLACK GROUND
4 RED POWER IN DC (10 to 32V)

FUSE
CA1

CA2

4P DIN TYPE CAMERA CONNECTOR 4P IP TYPE CAMERA CONNECTOR

CA1 CA2 CA1 CA2

OR

CAMERA (Not supplied)

* Normal / Tilt / Shutter camera

13
r SPECIFICATIONS

Model: ECL-750WP
Power Input DC 10V~32V
Power Consumption Max. 12Watt
Video System NTSC / PAL compatible
Panel 7" Digital
Resolution 800 (H) X3(RGB) X 480 (V) pixels
Format 16:9 wide
Display Mode Single
Camera input(2CH) Mini 4P DIN CONNECTOR or 4P IP CONNECTOR , 1Vp-p 75Ω
Operating Temp. -30℃ ~ +75℃ ( -22℉ ~ 167℉)
Storage Temp. -40℃ ~ +85℃ ( -40℉ ~ 185℉)
Vibration 6G
I.P Factor IP 68
OSD Control Day & Night Sensor
Bright, Contrast, Color, Tint
Mirror/Normal, Day/Night Mode/Scale
*Individual Control per Channel available
Dimension 194(W) X 124(D) X 30(H) mm
7.6(W) X 4.8(D) X 1.1(H) inch
Weight Approx. 730g
Supplied acc’y Power Cord (1)
Screw Kit (1)
Stand Bracket (1)
Sun Visor (1)
Instruction Manual (1)

14
THIS SYMBOL MEANS DO NOT DISPOSE OF
AS MUNICIPAL WASTE.
RE-USE OR RECYCLE WHEREVER POSSIBLE.
ELECTRICAL / ELECTRONIC COMPONENTS MAY
CONTAIN SUBSTANCES WHICH ARE HARMFUL TO
THE ENVIRONMENT.
FOR ENVIRONMENTALLY SOUND METHODS OF
DISPOSAL, PLEASE CONTACT YOUR LOCAL
GOVERNMENT AUTHORITY.

15
 Part no. 6MNEL750WP-00
printed in korea
16