PAGE 1 OF 2

TECHNICAL DATA SHEET

REV20221010

2500PC
Polypropylene Impact Copolymer (ICPP) / High Impact Injection Grade

PRODUCT DESCRIPTION
2500PC is a Polypropylene Impact Copolymer (ICPP) with high impact properties and high melt flow
ability. It is specially designed for injection molding processing such as paint pails applications and
other applications that require impact performance.

INDUSTRY PRODUCT FEATURE REGULATION COMPLIANCE

Containers and Pails High Impact Strength FDA US 21 CFR 177.1520
Household & Houseware Parts Good Processability Commission Regulation (EU) No. 10/2011
RoHS Directive 2011/65/EU
REACH Regulation (EC) No. 1907/2006
Halal Certificate

PHYSICAL PROPERTY TEST METHOD UNIT VALUE

Melt Flow Rate (230°C/2.16 kg) ASTM D1238 g/10 min 15

Density (23°C) ASTM D792 g/cm 3 0.90

Mold Shrinkage IRPC % 0.8 - 1.5

MECHANICAL PROPERTY
Tensile Strength at Yield (3.2 mm, 50 mm/min) ASTM D638 MPa 23

Elongation at Yield (3.2 mm, 50 mm/min) ASTM D638 % 6

Flexural Modulus (1% Secant, 3.2 mm, 1.3 mm/min) ASTM D790 MPa 1,130

Izod Notched Impact Strength (3.2 mm, 23°C) ASTM D256 J/m 130
Izod Notched Impact Strength (3.2 mm, -20°C) ASTM D256 J/m 50

HARDNESS PROPERTY
Rockwell Hardness (3.2 mm) ASTM D785 R Scale 87

THERMAL PROPERTY *Unannealed

Heat Distortion Temperature (3.2 mm, 0.455 MPa) ASTM D648 °C 92

2
Conversion (1 MPa = 10.2 kgf/cm | 1 J/m = 0.1 kgf•cm/cm )
Remark: The values presented above are typical laboratory, not to be construed as specifications and may vary within moderate ranges. The applicability or accuracy of this information or the suitability of our products cannot
be guaranteed because users’ conditions of use are beyond our control.

IRPC Public Company Limited | 555/2 Energy Complex, Building B, 6th Floor, Vibhavadi Rangsit Rd., Chatuchak, Bangkok 10900 THAILAND.
HTTPS://POLIMAXX.IRPC.CO.TH TEL : +66(0) 765-7000
 PAGE 2 OF 2

TECHNICAL DATA SHEET

REV20221010

2500PC
Polypropylene Impact Copolymer (ICPP) / High Impact Injection Grade

PROCESSING TECHNIQUE
Cylinder Temperature 190 - 240 °C
Mold Temperature 50 - 80 °C
Injection Pressure 30 - 80 % of maximum pressure
Holding Pressure Relative to injection pressure
Back Pressure 0 - 20% of maximum pressure
Injection Speed Low to medium of maximum pressure
However, the actual processing conditions depend on mold design, power of machine, equipment and other environments.

PRODUCT PACKAGING
25 kg loose bag
25 kg stretch wrap on palletized

750 kg Jumbo bag

For further information, contact IRPC’s Sales repesentative.

STORAGE
The resin should be stored in a dry location with good housekeeping practices during storage, transferring and

handling. Process enclosures and adequate ventilation should be used to avoid excessive dust accumulation. Resin

should be protected from direct sunlight, temperatures above 38°C (100°F) and high atmospheric humidity during

storage. Higher storage temperatures may reduce the storage time. The container should be kept closed to prevent

contamination. For the additional recommended storage conditions, please refer to SDS.

SAFETY
This product is not classified as hazardous material for more information please refer to safety data sheet.

RECYCLING
It is an undisputed fact that the product can be recycled or disposed of without any problem.

DISCLIAMER
The data indicated above are the results of our investigations, knowledge and correspond to the state of the art as of the date of publication and the data refer to the state
of the laws at the date of issue and this information expires after a break in delivery lasting more than 12 months or in case of regulatory changes. This statement is not
intended and should not be construed as specification, warranty or representation of any sort for which IRPC would be legal responsibility. The applicability or the accuracy
of this statement or the suitable of our products cannot be guaranteed because the conditions of use on the part our uses are beyond our control. IRPC gives no guarantees
or makes no warranties which extend beyond the description above herein. Nothing herein shall constitute any implied guaranty or warranty of merchantability or fitness for
a particular purpose. In the case that IRPC's products are used in combination with other materials, no liability can be accepted. When not utilized in combination with any
third-party products, the information included above refers only to our products. Please ask IRPC for a new information if needed. All terms and conditions regarding the
supply of IRPC's products shall be subject to IRPC's Policy, in the case of a dispute, the Company's decision is final and is not subject to any appeal.

IRPC Public Company Limited | 555/2 Energy Complex, Building B, 6th Floor, Vibhavadi Rangsit Rd., Chatuchak, Bangkok 10900 THAILAND.
HTTPS://POLIMAXX.IRPC.CO.TH TEL : +66(0) 765-7000