DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

Safety Data Sheet

Copyright,2022, Meguiar's Inc.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing Meguiar's Inc.
products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from Meguiar's Inc., and (2) neither the copy nor the original is resold or otherwise distributed with the intention of
earning a profit thereon.

Document Group: 28-6691-1 Version Number: 3.03

Issue Date: 05/26/22 Supercedes Date: 12/30/19

SECTION 1: Identification
1.1. Product identifier
DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116]

1.2. Recommended use and restrictions on use

Recommended use
Automotive, DA-applied wax

1.3. Supplier’s details

MANUFACTURER: Meguiar's, Inc.
DIVISION: Meguiar's
ADDRESS: 17991 Mitchell South, Irvine, CA 92614, USA
Telephone: 949-752-8000 (Fax: 949-752-5784)

1.4. Emergency telephone number

CHEMTREC 1-800-424-9300 (24 hours)

SECTION 2: Hazard identification

The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200.
This information may be different from the actual product label information for labels regulated by other agencies.

2.1. Hazard classification

Carcinogenicity: Category 2.

2.2. Label elements

Signal word
Warning

Symbols
Health Hazard |

Pictograms

Page 1 of 10
 DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

Hazard Statements
Suspected of causing cancer.

Precautionary Statements
General:
Keep out of reach of children.

Prevention:
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.

Response:
IF exposed or concerned: Get medical advice/attention.

Storage:
Store locked up.

Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.

2.3. Hazards not otherwise classified

Repeated exposure may cause skin dryness or cracking.

1% of the mixture consists of ingredients of unknown acute oral toxicity.

1% of the mixture consists of ingredients of unknown acute dermal toxicity.
1% of the mixture consists of ingredients of unknown acute inhalation toxicity.

SECTION 3: Composition/information on ingredients

Ingredient C.A.S. No. % by Wt
Water 7732-18-5 50 - 70 Trade Secret *
HYDROTREATED HEAVY NAPHTHA 64742-48-9 10 - 20 Trade Secret *
(PETROLEUM)
HYDROTREATED LIGHT PETROLEUM 64742-47-8 5- 10 Trade Secret *
DISTILLATES
Clay Trade Secret* 5 - 10 Trade Secret *
POLY(DIMETHYLSILOXANE) 63148-62-9 1 - 5 Trade Secret *
Synthetic Hydrocarbon Mixture Trade Secret* < 5 Trade Secret *
Titanium Dioxide 13463-67-7 < 0.5 Trade Secret *

*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Page 2 of 10
 DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

Remove person to fresh air. If you are concerned, get medical advice.

Skin Contact:
Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:
No need for first aid is anticipated.

If Swallowed:
Rinse mouth. If you are concerned, get medical advice.

4.2. Most important symptoms and effects, both acute and delayed
No critical symptoms or effects. See Section 11.1, information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required
Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media
In case of fire: Use a carbon dioxide or dry chemical extinguisher to extinguish.

5.2. Special hazards arising from the substance or mixture

Closed containers exposed to heat from fire may build pressure and explode.

Hazardous Decomposition or By-Products

Substance Condition
Hydrocarbons During Combustion
Formaldehyde During Combustion
Carbon monoxide During Combustion
Carbon dioxide During Combustion
Irritant Vapors or Gases During Combustion

5.3. Special protective actions for fire-fighters

Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and
prevent explosive rupture. Wear full protective clothing, including helmet, self-contained, positive pressure or pressure
demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering
for exposed areas of the head.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures
Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation
to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Refer to other sections of this SDS for
information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.

6.2. Environmental precautions

Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or
bodies of water.

6.3. Methods and material for containment and cleaning up

Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible.
Place in a closed container approved for transportation by appropriate authorities. Clean up residue with detergent and
water. Seal the container. Dispose of collected material as soon as possible in accordance with applicable

Page 3 of 10
 DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

local/regional/national/international regulations.

SECTION 7: Handling and storage

7.1. Precautions for safe handling
Do not use in a confined area with minimal air exchange. Keep out of reach of children. Do not handle until all safety
precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin,
or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Avoid release to
the environment. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.) Use personal protective equipment
(gloves, respirators, etc.) as required.

7.2. Conditions for safe storage including any incompatibilities

Store away from heat. Store away from acids. Store away from strong bases. Store away from oxidizing agents.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available
for the component.
Ingredient C.A.S. No. Agency Limit type Additional Comments
Titanium Dioxide 13463-67-7 ACGIH TWA:10 mg/m3 A4: Not class. as human
carcin
Titanium Dioxide 13463-67-7 OSHA TWA(as total dust):15 mg/m3
Kerosine (petroleum) 64742-47-8 ACGIH TWA(as total hydrocarbon A3: Confirmed animal
vapor, non-aerosol):200 carcin., SKIN
mg/m3
ACGIH : American Conference of Governmental Industrial Hygienists
AIHA : American Industrial Hygiene Association
CMRG : Chemical Manufacturer's Recommended Guidelines
OSHA : United States Department of Labor - Occupational Safety and Health Administration
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling

8.2. Exposure controls

8.2.1. Engineering controls

Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure
Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment.

8.2.2. Personal protective equipment (PPE)

Eye/face protection
None required.

Skin/hand protection
Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the
results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the
substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.
Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective
clothing. Note: Nitrile gloves may be worn over polymer laminate gloves to improve dexterity.
Gloves made from the following material(s) are recommended: Polymer laminate

When only incidental contact is anticipated, alternative glove material(s) may be used. If contact with the glove does occur,

Page 4 of 10
DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

remove immediately and replace with a set of new gloves. For incidental contact, gloves made of the following material(s)
may be used:Nitrile Rubber

Respiratory protection

Wear respiratory protection if ventilation is inadequate to prevent overexposure.

An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part
of a full respiratory protection program. Based on the results of the exposure assessment, select from the following
respirator type(s) to reduce inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for particulates

For questions about suitability for a specific application, consult with your respirator manufacturer.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Appearance
Physical state Liquid
Color Blue, Gray

Odor Sweet Odor

Odor threshold No Data Available
pH 7.9 - 8.5
Melting point Not Applicable
Boiling Point 380 ºF
Flash Point >= 200 ºF [Test Method:Pensky-Martens Closed Cup]
[Details:D93-90]
Evaporation rate No Data Available
Flammability (solid, gas) Not Applicable
Flammable Limits(LEL) No Data Available
Flammable Limits(UEL) No Data Available
Vapor Pressure No Data Available
Vapor Density No Data Available
Density 0.91 - 1.01 g/cm3
Specific Gravity 0.91 - 1.01 [Ref Std:WATER=1]
Solubility in Water Moderate
Solubility- non-water No Data Available
Partition coefficient: n-octanol/ water No Data Available
Autoignition temperature No Data Available
Decomposition temperature No Data Available
Viscosity 23,000 centipoise - 33,000 centipoise
Hazardous Air Pollutants 0.00144 lb HAPS/lb solids
Molecular weight No Data Available
Volatile Organic Compounds 15 % weight [Test Method:calculated per CARB title 2]
Percent volatile No Data Available
VOC Less H2O & Exempt Solvents 516 g/l [Test Method:calculated SCAQMD rule 443.1]

SECTION 10: Stability and reactivity

10.1. Reactivity
This material is considered to be non reactive under normal use conditions.

10.2. Chemical stability

Stable.

Page 5 of 10
DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

10.3. Possibility of hazardous reactions

Hazardous polymerization will not occur.

10.4. Conditions to avoid

Temperatures above the boiling point

10.5. Incompatible materials

Strong acids
Strong bases
Strong oxidizing agents

10.6. Hazardous decomposition products

Substance Condition
None known.

Refer to section 5.2 for hazardous decomposition products during combustion.

SECTION 11: Toxicological information

The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.

11.1. Information on Toxicological effects

Signs and Symptoms of Exposure

Based on test data and/or information on the components, this material may produce the following health effects:

Inhalation:
May cause additional health effects (see below).

Skin Contact:
Prolonged or repeated exposure may cause: Dermal Defatting: Signs/symptoms may include localized redness, itching,
drying and cracking of skin.

Eye Contact:
Contact with the eyes during product use is not expected to result in significant irritation.

Ingestion:
No known health effects.

Additional Health Effects:

Carcinogenicity:
Contains a chemical or chemicals which can cause cancer.

Ingredient CAS No. Class Description Regulation

Titanium dioxide 13463-67-7 Grp. 2B: Possible human carc. International Agency for Research on Cancer

Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.

Page 6 of 10
DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

Acute Toxicity
Name Route Species Value
Overall product Dermal No data available; calculated ATE >5,000 mg/kg
Overall product Inhalation- No data available; calculated ATE >50 mg/l
Vapor(4 hr)
Overall product Ingestion No data available; calculated ATE >5,000 mg/kg
HYDROTREATED HEAVY NAPHTHA (PETROLEUM) Inhalation- LC50 estimated to be 20 - 50 mg/l
Vapor
HYDROTREATED HEAVY NAPHTHA (PETROLEUM) Dermal Rabbit LD50 > 5,000 mg/kg
HYDROTREATED HEAVY NAPHTHA (PETROLEUM) Ingestion Rat LD50 > 5,000 mg/kg
Clay Dermal LD50 estimated to be 2,000 - 5,000 mg/kg
Clay Ingestion Rat LD50 > 2,000 mg/kg
HYDROTREATED LIGHT PETROLEUM DISTILLATES Inhalation- Professio LC50 estimated to be 20 - 50 mg/l
Vapor nal
judgeme
nt
HYDROTREATED LIGHT PETROLEUM DISTILLATES Dermal Rabbit LD50 > 5,000 mg/kg
HYDROTREATED LIGHT PETROLEUM DISTILLATES Ingestion Rat LD50 > 5,000 mg/kg
POLY(DIMETHYLSILOXANE) Dermal Rabbit LD50 > 19,400 mg/kg
POLY(DIMETHYLSILOXANE) Ingestion Rat LD50 > 17,000 mg/kg
Titanium Dioxide Dermal Rabbit LD50 > 10,000 mg/kg
Titanium Dioxide Inhalation- Rat LC50 > 6.82 mg/l
Dust/Mist
(4 hours)
Titanium Dioxide Ingestion Rat LD50 > 10,000 mg/kg
ATE = acute toxicity estimate

Skin Corrosion/Irritation
Name Species Value

HYDROTREATED HEAVY NAPHTHA (PETROLEUM) Rabbit Minimal irritation

HYDROTREATED LIGHT PETROLEUM DISTILLATES Rabbit Minimal irritation
POLY(DIMETHYLSILOXANE) Rabbit No significant irritation
Titanium Dioxide Rabbit No significant irritation

Serious Eye Damage/Irritation

Name Species Value

HYDROTREATED HEAVY NAPHTHA (PETROLEUM) Rabbit Mild irritant

HYDROTREATED LIGHT PETROLEUM DISTILLATES Rabbit Mild irritant
POLY(DIMETHYLSILOXANE) Rabbit No significant irritation
Titanium Dioxide Rabbit No significant irritation

Skin Sensitization
Name Species Value
HYDROTREATED HEAVY NAPHTHA (PETROLEUM) Guinea Not classified
pig
HYDROTREATED LIGHT PETROLEUM DISTILLATES Guinea Not classified
pig
Titanium Dioxide Human Not classified
and
animal

Respiratory Sensitization
For the component/components, either no data are currently available or the data are not sufficient for classification.

Germ Cell Mutagenicity

Name Route Value

HYDROTREATED HEAVY NAPHTHA (PETROLEUM) In Vitro Not mutagenic

Page 7 of 10
DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

HYDROTREATED HEAVY NAPHTHA (PETROLEUM) In vivo Not mutagenic

HYDROTREATED LIGHT PETROLEUM DISTILLATES In Vitro Not mutagenic
HYDROTREATED LIGHT PETROLEUM DISTILLATES In vivo Not mutagenic
Titanium Dioxide In Vitro Not mutagenic
Titanium Dioxide In vivo Not mutagenic

Carcinogenicity
Name Route Species Value
HYDROTREATED HEAVY NAPHTHA (PETROLEUM) Not Not Not carcinogenic
Specified available
HYDROTREATED LIGHT PETROLEUM DISTILLATES Not Not Not carcinogenic
Specified available
Titanium Dioxide Ingestion Multiple Not carcinogenic
animal
species
Titanium Dioxide Inhalation Rat Carcinogenic

Reproductive Toxicity

Reproductive and/or Developmental Effects

Name Route Value Species Test Result Exposure
Duration
HYDROTREATED HEAVY NAPHTHA Not Not classified for female reproduction Not NOAEL NA 1 generation
(PETROLEUM) Specified available
HYDROTREATED HEAVY NAPHTHA Not Not classified for male reproduction Not NOAEL NA 28 days
(PETROLEUM) Specified available
HYDROTREATED HEAVY NAPHTHA Not Not classified for development Not NOAEL NA during
(PETROLEUM) Specified applicabl gestation
e
HYDROTREATED LIGHT PETROLEUM Not Not classified for female reproduction Rat NOAEL Not 1 generation
DISTILLATES Specified available
HYDROTREATED LIGHT PETROLEUM Not Not classified for male reproduction Rat NOAEL Not 28 days
DISTILLATES Specified available
HYDROTREATED LIGHT PETROLEUM Not Not classified for development Rat NOAEL Not during
DISTILLATES Specified available gestation

Target Organ(s)

Specific Target Organ Toxicity - single exposure

For the component/components, either no data are currently available or the data are not sufficient for classification.

Specific Target Organ Toxicity - repeated exposure

Name Route Target Organ(s) Value Species Test Result Exposure
Duration
Titanium Dioxide Inhalation respiratory system Some positive data exist, but the Rat LOAEL 0.01 2 years
data are not sufficient for mg/l
classification
Titanium Dioxide Inhalation pulmonary fibrosis Not classified Human NOAEL Not occupational
available exposure

Aspiration Hazard
Name Value
HYDROTREATED HEAVY NAPHTHA (PETROLEUM) Aspiration hazard
HYDROTREATED LIGHT PETROLEUM DISTILLATES Aspiration hazard

Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.

SECTION 12: Ecological information

Ecotoxicological information

Page 8 of 10
 DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material
and/or its components.
Chemical fate information
Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material
and/or its components.

SECTION 13: Disposal considerations

13.1. Disposal methods
Dispose of contents/ container in accordance with the local/regional/national/international regulations.

Dispose of waste product in a permitted industrial waste facility. As a disposal alternative, incinerate in a permitted waste
incineration facility. Proper destruction may require the use of additional fuel during incineration processes. Empty
drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations
classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes
unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the
available treatment and disposal facilities.

SECTION 14: Transport Information

General Transportation Statement: This product does not require classification by DOT, IATA, ICAO or IMDG.

Please contact the emergency numbers listed on the first page of the SDS for Transportation Information for this material.

SECTION 15: Regulatory information

15.1. US Federal Regulations

Contact manufacturer for more information

EPCRA 311/312 Hazard Classifications:

Physical Hazards
Not applicable

Health Hazards
Carcinogenicity
Hazard Not Otherwise Classified (HNOC)

15.2. State Regulations

Contact manufacturer for more information

15.3. Chemical Inventories

The components of this product are in compliance with the chemical notification requirements of TSCA. All required
components of this product are listed on the active portion of the TSCA Inventory.

Contact manufacturer for more information

15.4. International Regulations

Contact manufacturer for more information

This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.

Page 9 of 10
DA Microfiber Finishing Wax (Detailer) D301 [D30101 D30116] 05/26/22

SECTION 16: Other information

NFPA Hazard Classification
Health: 0 Flammability: 1 Instability: 0 Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.

Document Group: 28-6691-1 Version Number: 3.03

Issue Date: 05/26/22 Supercedes Date: 12/30/19

DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. Meguiar's Inc.
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the Meguiar's Inc. product is fit for
a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use
and application of a Meguiar's Inc. product, some of which are uniquely within the user's knowledge and control, it is
essential that the user evaluate the Meguiar's Inc. product to determine whether it is fit for a particular purpose and suitable
for user's method of use or application.

Meguiar's Inc. provides information in electronic form as a service to its customers. Due to the remote possibility that
electronic transfer may have resulted in errors, omissions or alterations in this information, Meguiar's Inc. makes no
representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as
the information in the SDS available directly from Meguiar's Inc.

Meguiar's, Inc. USA SDSs are available at www.Meguiars.com

Page 10 of 10