PRODUCT DATA SHEET
Sikafloor® CureHard LI
Lithium silicate liquid hardener and densifier
DESCRIPTION The product is used for:
▪ Warehouses
Sikafloor® CureHard LI is a water-based lithium silicate ▪ Industrial buildings
blend for hardening and densifying of fresh and ▪ Storage areas
hardened power trowelled or polished concrete sur- ▪ Retail areas
faces. It is less prone to the formation of persistent ef- ▪ Car park decks
florescence in cases of over dosage compared to simil- ▪ Service facilities
ar products based on sodium or potassium silicate. It ▪ Aircraft hangars
improves surface performance and resists the harmful
effects of traffic wear and weathering. CHARACTERISTICS / ADVANTAGES
Once applied to a concrete surface Sikafloor® Cure-
Hard LI penetrates the concrete texture and is initiat- ▪ Improves performance, dust reduction and abrasion
ing a chemical reaction and subsequent crystallization resistance of new or old concrete.
of reaction products which result in filling of the con- ▪ Sealing and impregnation of concrete surface.
crete surface pores. ▪ Easy, one step application. No scrubbing. No flush-
ing.
USES ▪ Reduced appearance of efflorescence, compared to
crystalline sodium or potassium based hardeners.
Sikafloor® CureHard LI may only be used by experi- ▪ No enhancement effect on the floor colour.
enced professionals. ▪ Gives the concrete surface silk gloss appearance.
▪ High gloss of the surface after each regular cleaning.
▪ Horizontal old or new concrete surfaces, where a ▪ Breathable and UV stable. Will not yellow, discolour,
hard surface with light to moderate abrasion resist- peel or flake.
ance is required.
▪ Suitable for interior or exterior applications APPROVALS / STANDARDS
▪ Dust-proofing of prefabricated concrete elements.
▪ The Product may only be used by experienced pro- ▪ CE marking and declaration of performance based on
fessionals. EN 1504-2:2004 Products and systems for the pro-
tection and repair of concrete structures — Surface
protection systems for concrete — Impregnation
PRODUCT INFORMATION
Product Declaration EN 1504- 2 : Suitable for protection against ingress (Principle 1, method 1.2
of EN 1504-9) : Suitable for physical resistance (Principle 5, method 5.2 of
EN 1504-9).
Chemical Base Lithium silicate
Packaging 25 L container, 200 L drum
Shelf Life 12 months from date of production
Product Data Sheet
Sikafloor® CureHard LI
May 2022, Version 02.01
020815010110000007
1/5
Storage Conditions The product must be stored in original, unopened and undamaged sealed
packaging in dry conditions at temperatures between +5 °C and +30 °C. Al-
ways refer to packaging.
Refer to current Safety Data Sheet for information on safe handling and
storage.
Appearance / Colour Clear liquid
Density (1160 ± 58) kg/m3 (EN ISO 2811-1)
Solid content by weight (14.5 ± 1.5) % (EN ISO 2811-1)
TECHNICAL INFORMATION
Abrasion Resistance 290 mg (H22 / 1000 g / 1000 cycles) (EN ISO 5470-
78 % increase in abrasion resistance compared to untreated 1)
sample.
(C(0,70) concrete according to EN 1766)
Resistance to Impact 60 Nm (class III: ≥ 20 Nm) (EN ISO 6272-1)
sample MC(0,40 concrete according to EN 1766
Tensile Adhesion Strength 4.4 N/mm2 (EN 1542)
sample C(0,70 concrete according to EN 1766
Penetration Depth 6 mm (EN 1504-2)
sample C(0,70 concrete according to EN 1766
Water Absorption w = 0.03 kg·m-2·h-0.5 (EN 1062-3)
(on a substrate w > 1 kg·m-2.h-0.5)
SYSTEM INFORMATION
System Structure Hardener / densifier 1–2 coats
APPLICATION INFORMATION
Consumption ~0.05–0.10 L/m2 (~10–20 m²/L) on power trowelled concrete
Consumption data is theoretical and does not allow for any additional ma-
terial due to surface porosity, surface profile, variations in level, wastage
or any other variations. Apply product to a test area to calculate the exact
consumption for the specific substrate conditions and proposed applica-
tion equipment.
Ambient Air Temperature Hot weather conditions
In hot weather (above +25 °C) store the Product in a cool place prior to
use.
Cold weather conditions
In low temperatures (below +10 °C) the Product may thicken and be diffi-
cult to spray.
Maximum +40 °C
Minimum +2 °C
Relative Air Humidity < 100 %
Substrate Temperature Maximum +35 °C
Minimum +5 °C
Substrate Moisture Content May be applied on fresh concrete after powertroweling, optically matt dry
surface. The Product can also be applied to fully cured and set concrete
with a matt dry surface, no standing water or puddles.
Product Data Sheet
Sikafloor® CureHard LI
May 2022, Version 02.01
020815010110000007
2/5
Waiting Time / Overcoating Where two applications are required to ensure maximum densification the
second application should be installed after the first one is dry. Allow pre-
vious application surface to become dry and tack free before applying ad-
ditional application.
Temperature Waiting time
+25 °C ~ 1.5 hours
+20 °C ~ 2 hours
+10 °C ~ 3 hours
+5 °C ~ 3.5 hours
Times are approximate and will be affected by changing ambient condi-
tions, particularly temperature and relative humidity.
Drying Time Touch-dry, at 20 °C 2 hours
Applied Product Ready for Use Temperature Fully serviceable Full sealing and harden-
ing effect
+30 °C ~2 hours
+20 °C ~3 hours ~7 days
+10 °C ~4.5 hours
Times are approximate and will be affected by changing ambient condi-
tions, particularly temperature and relative humidity.
BASIS OF PRODUCT DATA APPLICATION INSTRUCTIONS
All technical data in this document are based on labor-
atory tests. Actual measured data may vary due to cir- SUBSTRATE QUALITY
cumstances beyond our control.
IMPORTANT
Existing membranes
LIMITATIONS Do not use on substrates treated previously with cur-
ing agents, membrane forming sealers or asphalt until
▪ Sikafloor® CureHard LI must be treated mechanically these layers have been completely removed.
(from light to heavy shot blasting depending on the Apply the Product on a small area of each surface to
depth of the penetration) prior to the application of confirm suitability, coverage rate and desired results
a coating system. before beginning the full application. Test with the
▪ Immediately wash over-spray from glass, aluminium
same equipment, surface preparation and application
or highly polished surfaces with water to avoid etch-
procedures planned for general application.
ing of surfaces.
▪ Performance enhancement of the substrates can EXISTING, CURED CONCRETE
vary greatly depending on the age, cement content, Surfaces must be sound, open textured, clean, free
humidity content, porosity and penetration of the from frost, laitance, surface water, oils, grease, coat-
product into the substrate. ings, all loosely adhering particles and other surface
▪ Sikafloor® CureHard LI will increase abrasion resist- contaminants. Any residue of curing agents must be
ance compared to untreated concrete of the same completely removed from all surfaces before applica-
type, however Sikafloor® CureHard LI cannot com- tion of the Product. If in doubt apply a test area first.
pensate performance of a poor substrate made with NEW CONCRETE
low cement content. It is not recommended to apply Allow new concrete to cure for a minimum of 72
on substrates which are lightweight, extremely por- hours. For the best results with new concrete floors
ous or have worn (aggregate exposed) surfaces. wait for 7 days after placement or until after cement
▪ Sikafloor® CureHard LI will not hide serious staining has sufficiently hydrated prior to treatment with the
or excessive wear. Product. After the curing period has elapsed, treat
new concrete surfaces as described for Existing, Cured
ECOLOGY HEALTH AND SAFETY Concrete.
FRESHLY PLACED, UNCURED STEEL-TROWELLED CON-
For information and advice on the safe handling, stor- CRETE
age and disposal of chemical products, users shall Surface must be matt dry and of sufficient strength to
refer to the most recent Safety Data Sheet (SDS) con- withstand finishing operations. Clean concrete of any
taining physical, ecological, toxicological and other dirt, residue or debris.
safety-related data.
Product Data Sheet
Sikafloor® CureHard LI
May 2022, Version 02.01
020815010110000007
3/5
SUBSTRATE PREPARATION ately apply more product. Surface should remain wet
for 5–10 minutes.
FRESH CONCRETE: 4. Allow treated surfaces to dry.
The concrete must be prepared by power or manual 5. Immediately initiate the specified curing procedure.
floating/tamping techniques. 6. When curing is complete, use an automatic floor
HARDENED / OLD CONCRETE: scrubber equipped with cleaning pads or brushes ap-
The substrate must be prepared by high pressure wa- propriate for removal of accumulated derbis and sur-
ter cleaning or by ride-on cleaning machines. Allow to face residues. Note: Avoid pads or brushes which
dry. may damage the finished floor.
Note: All dust, dirt, loose and friable material must be
completely removed from all surfaces before applica- CLEANING OF TOOLS
tion of the Product by brush or vacuum.
Clean all tools and application equipment with water
APPLICATION immediately after use. Hardened material can only be
removed mechanically.
IMPORTANT
Do not mix with other curing products MAINTENANCE
Do not mix various formulations of Sika® or other cur-
ing membranes. Do not use sprayers which have previ-
ously been used to spray silicones or release agents. CLEANING
Ensure spraying equipment is cleaned thoroughly be-
fore use and residues of previous membranes are re- To maintain the appearance of the floor after applica-
moved. tion, the Product must have all spillages removed im-
Maintain a continuous film mediately and must be regularly cleaned using rotary
When applying, do not leave dry spots in order to brushes, mechanical scrubbers, scrubber dryers, high
achieve homogenous performance. Touch up where pressure washers, wash and vacuum techniques, etc.,
necessary. using suitable detergents and waxes.
EXISTING, CURED CONCRETE AND NEW CONCRETE The frequency and intensity of the wet cleaning will
1. Using a low pressure sprayer, apply a single applica- directly influence the how soon and how deep the
tion sufficient to wet the surface without producing glossy anti-dust surface develops.
puddles. Avoid over application.
2. Use a clean microfiber pad to spread the product
evenly and ensure uniform wetting. Note: Avoid
spreading once drying begins.
3. (Optional) Alternatively use a cleaning machine with
soft pads to apply the Product.
4. Scrubbing is not necessary. If surfaces dry immedi-
ately apply more product. Surface should remain wet
for 5–10 minutes.
5. Allow treated surfaces to dry.
6. Remove dried powder residue using stiff broom,
power sweeper or floor scrubbing machine.
7. For strongly absorbent floors is a second application
is required.
8. For immediate, enhanced shine, buff or burnish the
dry concrete surface in perpendicular directions by
using burnisher equipped with an appropriate polish-
ing pad. This is a dry operation.
FRESHLY PLACED, UNCURED STEEL-TROWELLED CON-
CRETE
1. Using a low pressure sprayer, apply a single applica-
tion sufficient to wet the surface without producing
puddles. Avoid over application.
2. Use a clean microfiber pad to spread the product
evenly and ensure uniform wetting. Note: Avoid
spreading once drying begins.
3. Scrubbing is not necessary. If surfaces dry immedi-
Product Data Sheet
Sikafloor® CureHard LI
May 2022, Version 02.01
020815010110000007
4/5
LOCAL RESTRICTIONS
Note that as a result of specific local regulations the
declared data and recommended uses for this product
may vary from country to country. Consult the local
Product Data Sheet for the exact product data and
uses.
LEGAL NOTES
The information, and, in particular, the recommenda-
tions relating to the application and end-use of Sika
products, are given in good faith based on Sika's cur-
rent knowledge and experience of the products when
properly stored, handled and applied under normal
conditions in accordance with Sika's recommenda-
tions. In practice, the differences in materials, sub-
strates and actual site conditions are such that no war-
ranty in respect of merchantability or of fitness for a
particular purpose, nor any liability arising out of any
legal relationship whatsoever, can be inferred either
from this information, or from any written recom-
mendations, or from any other advice offered. The
user of the product must test the product’s suitability
for the intended application and purpose. Sika re-
serves the right to change the properties of its
products. The proprietary rights of third parties must
be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which
will be supplied on request.
Sika South Africa (Pty) Ltd
9 Hocking Place,
Westmead, 3608
South Africa
Phone +27 31 792 6500
www.sika.co.za
SikafloorCureHardLI-en-ZA-(05-2022)-2-1.pdf
Product Data Sheet
Sikafloor® CureHard LI
May 2022, Version 02.01
020815010110000007
5/5
