Calculator 03.25.03 Ver. 2.

Calculator Is For Reference Only!

Always Check Calculations Manually!

All Input Welcome, Improvement, Repairs, Additional Calculations
The Most Recent Version Can Be Downloaded At The CPS Portal
file:\\halweb.halnet.com\km\cps\Calculators and Converters

Contact
[email protected]
Area
Annular Area Single String
Annular Area Multiple Strings
Area Of A Circle
Area Between Two Circles
Cross-Sectional Area ( Seal Assy. Inserted )

Circle
Circumference Of A Circle
Diameter Of A Circle
Radius Of A Circle

Constants
Thermal Coefficients
Fresh Water Facts

Conversions
Barrel To Cu./ Ft.
Cubic Foot To Barrel
Cubic Foot To Cubic Inches
Gradient
Specific Gravity To Gradient
API Gravity To Gradient
Density lb./ ft.3 To Gradient
Measurement
Decimal To Fraction
Fraction To Decimal
Inche To Foot Converion
Specific Gravity
Fluid Weight lb./ gal. To Specific Gravity
API Gravity To Specific Gravity
Density lb./ ft.3 To Specific Gravity

Directional Well Calculations

To Find TVD From MD
To Find MD From TVD
To Find Deviation Factor
To Find True Vertical Length Of Slant
To Find Slant Factor
Directional Acronyms

Fluid
Fluid Weight To Gradient
Fluid Velocity
Fluid Weigh Up
Fluid Cut Back
KCL
CaCl2 Weigh Up ( Using 94-97% CaCl2 )
CaBr2 & ZnBr2 Weigh Up ( Using 94-97% CaCl2 )
CaBr2 & ZnBr2 Weigh Up ( Using 95% CaBr2 )

Gravel Pack
Yield & Fluid Wt. Of Slurry After Adding Sand
Wash Pipe / Screen Ratio ( Optimum Is 80% )
Minimum Clearance For Gravel Pack Completions
Drift Plate Tolerance

Leaks
Locating

Packer
Velocity Of Fluid Across Packer Elements

Piston Effects
Piston Force Exerted
Piston Pressure Created
Pressure
Hydrostatic Pressure
Fluid Weight Required For BHP @ Depth
Maximum Allowable Pump Pressure

Pumps
Triplex Pump Output Barrels Per Stroke

SCSSV
Maximum Leakage Rate of SCSSV and Plugs
Maximum Fail-Closed Setting Depth
Specific Gravity To Gradient
Recommended Control Line Hold Open Pressure
Control Line Fluid Volume

Shear Pins
To Calculate Pin Shear Force
Pressure Required To Shear Pins

Slickline
Area Of A Slickline
Tool String Balance Weight Neglecting Friction
Stem Weight
Stem Length Needed Neglecting Friction
Minimum Bending Diameter Of Wire
Wire Weight
Wire Weight Balance Depth
Wire Strength ( approximate / standard plow steel )
Spool Capacity
Tubing Fill-Up Rule Of Thumb
Hydrostatic Rule Of Thumb
Rule Of Thumb For WireLine Fall-Back
Area Of Pipe
Temperature
Average Pipe Temperature
Change In pipe length ( inches ) due to temperature change
Change In Average Tubing Temperature, Injecting / Acidizing Condition
Change In Average Tubing Temperature, Flowing Condition
Converting Temperature Change To Length Change

Tubing
I.D. Calculated
Joint Yield Strength Of EUE Tubing
Cross-Sectional Area Of Pipe
Tubing Weight In Air
Tubing Weight With Upsets & Coupling
Tubing Weight In Fluid
Buoyancy Factor
Buoyancy Factor Bull Plugged In Fluid ( lb./ ft. )
Tubing Capacity
Tubing Fill-Up Factors
Tubing Fill-Up
Tubing Displacement
Pipe Stretch
Slack-Off Data
Slack-Off Factor
Determining Pipe Pull
Free Pipe Depth

Volume
Rectangular Volume / Capacity
Cylindrical Volume / Capacity
Spherical Volume / Capacity
Pipe / Hose Volume
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Annular Area Single String
( ID2 x .7854 ) - ( OD2 x .7854 ) = Annular Area
Casing ID 8.291 Area In2
Tubing OD 2.875 47.497

Annular Area Multiple Strings

( ID x .7854 ) - (( OD2 +OD2 + OD2 + OD2 ) x .7854 ) = Annular Area
2

Casing ID 8.291
Tubing OD #1 2.375
Tubing OD #2 2.375 Area In2
Tubing OD #3 45.129
Tubing OD #4
ormation In Highlighted Areas
EFERENCE ONLY
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Area Of A Circle
3.1416 x Radius2 = Area
Radius 6.000 Area 113.098
Diameter2 x .7854 = Area
Diameter 3.000 Area 7.069

Area Between Two Circles

( ID2 x .7854 ) - ( OD2 x .7854 ) = Area Between Circles
Outer Circle ID 5.000 Area
Inner Circle OD 4.000 7.069

Cross-Sectional Area ( Seal Assy. Inserted )

((ID2 - ID2 ) x .7854 = Area
Receptacle ID 3.000 Area
Seal Assy. ID 2.330 2.805
ormation In Highlighted Areas
EFERENCE ONLY
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Fresh Water Facts SPECIFIC GRAVITY
Density = 62.4 lb./ cu.ft. Fluid Weight lb./ gal. To Specific Gravity
Weight = 8.33 lb./ gal. Fluid Wt. / 8.33 = S.G.
Fluid Gradient = 0.433 Fluid Wt.lb./ gal. 10 S.G.
Specific Gravity = 1.000 API Gravity To Specific Gravity
API Gravity = 10.000 141.5 / ( 131.5 + API Gravity ) = S.G.
API Gravity 40 S.G.
Fluid Gradient Of 1 lb./ gal. Fluid = 0.051948 Density lb./ ft.3 To Specific Gravity
Desity lb./ ft.3 / 62.4 = Specific Gravity
Pi = 3.1416 Desity lb./ ft.3 70 S.G.
1 Barrel = 42 gallon
1 Barrel = 5.6146 cu./ ft. GRADIENT
1 Barrel = 9702 sq./ in.. Specific Gravity To Gradient
1 Cubic Foot = 1728 cu./ in. S.G. x .433 = Gradient
1 Cubic Foot = 0.1781 barrels Specific Gravity 1.2 Gradient
1 Cubic Foot = 7.4805 gallon API Gravity To Gradient
1 Cubic Foot = .1781 barrel 61.28 / ( 131.5 + API Gravity ) = Gradient
1 Gallon = .00238 barrel API Gravity 40 Gradient
1 Gallon = .1337 cu./ ft. Density lb./ ft.3 To Gradient
1 Gallon = 231 cu./ in. Desity lb./ ft.3 / 144 = Gradient
Desity lb./ ft.3 70 Gradient
Thermal Coefficients
Steel = 0.0000069 CIRCLE
13Cr. = 0.0000057 Circumference Of A Circle
Inc. 825 & 925 = 0.0000078 Pi 3.1416 x Diameter = Circumference
Hastalloy C-276 = 0.0000067 Diameter Circumference
2 6.2832
Coefficiet of thermal expansion ( or Contraction ) for steel per Diameter Of A Circle
unit of length per Degree F = .0000069 Circumference / Pi 3.1416 = Diameter
Circumference 6.2832 Diameter
Barrel To Cu./ Ft. Radius Of A Circle
Barrels x 5.6146 = Cu./ Ft. Diameter / 2 = Radius
Barrels 2 Cubic Ft. 11.229 Diameter 2 Radius

Cubic Foot To Barrel

Cubic Ft x .1781 = Barrel
Cubic Foot 1 Barrel 0.1781

Cubic Foot To Cubic Inches

Cubic Ft x 1728 = Cubic Inches
Cubic Foot 1 Cubic In. 1728.000
ation In Highlighted Areas
RENCE ONLY
C GRAVITY Decimal To Fraction
al. To Specific Gravity Decimal Number * Desired Fraction Increment
/ 8.33 = S.G. Decimal Number Fraction
1.200 0.188 12.03 /64
o Specific Gravity 6.02 /32
API Gravity ) = S.G. 3.01 /16
0.825 1.50 /8
To Specific Gravity 0.75 /4
.4 = Specific Gravity Fraction To Decimal
1.122 Numerator ( top number ) / Denomanator ( bottom number ) `
Fraction Decimal
ADIENT 28 /64 0.438
vity To Gradient 28 /32 0.875
3 = Gradient 13 /16 0.813
0.520 7 /8 0.875
y To Gradient
PI Gravity ) = Gradient Inche To Foot Converion
0.357 Inches
ft.3 To Gradient 75.00
/ 144 = Gradient Engineers Tape
0.486 Feet
6.250
RCLE Carpenters Tape
nce Of A Circle Feet Inches Fraction
eter = Circumference 6 3 0.00 /64
Circumference 0.00 /32
6.2832 0.00 /16
Of A Circle 0.00 /8
Pi 3.1416 = Diameter 0.00 /4
2.000
Of A Circle
/ 2 = Radius
1.000
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Directional Well Calculations
To Find TVD From MD
(( MD - Kickoff Depth) x Deviation Factor)+Kickoff Depth = TVD
MD 10000 TVD
Kickoff Depth 5000 7500.00
Deviation Factor 0.5
To Find MD From TVD
(( TVD - Kickoff Depth )/ Deviation Factor ) + Kickoff Depth = MD
TVD 7500 MD
Kickoff Depth 5000 10000.00
Deviation Factor 0.5
To Find Deviation Factor
( TVD - Kickoff Depth ) / ( MD - Kickoff Depth )
TVD 7500 Deviation Factor
MD 10000 0.500
Kickoff Depth 5000
To Find True Vertical Length Of Slant
Slant Factor 1.5 Length
Length Of Pipe 7500 11250
To Find Slant Factor
True Height Of Slant / Length Of Slant = Slant Factor
True Height Of Slant Length Of Slant Slant Factor
7500 5000 1.5000

Measurements OF Directional Holes

VSS - Vertical depth measured from sea level
VSF - Vertical depth from T.H.F.
MSF - Drilled depth from T.H.F.
MKB - Measure Depth from Kelly Bushing
VKB - Vertical depth from Kelly Bushing
ormation In Highlighted Areas
EFERENCE ONLY
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Fluid Weight To Gradient Fluid Weigh Up
Fluid Wt. x .05195 = Gradient ( Desired Wt. - Original Wt. ) / ( Weigh Up Wt. - Desired Wt. ) x
Fluid Wt.lb./ gal. Gradient Volume To Weigh Up
10.000 0.5196 Volume To Weigh Up ( bbl )
Fluid Wt.lb./ ft.3 / 144 = Gradient Original Mud Weight ( lb / gal )
Fluid Wt.lb./ ft.3 Gradient Desired Mud Weight ( lb / gal )
1.500 0.0104 Weigh Up Mud Weight ( lb / gal )
Volume Of Weigh Up Mud Needed
Fluid Velocity Total Volume After Weigh Up
Proposed Pumping Rate ( BPM ) 10.00 Fluid Cut Back
Outer ID / In. 8.921 ( Original Wt. - Desired Wt. ) / ( Desired Wt. - Cut Back Wt. ) x
Inner OD / In. 2.875 Volume To Cut Back
Fluid Velocity ( FPS ) 2.406 Volume To Cut Back ( bbl )
Fluid Velocity ( FPM ) 144.340 Original Mud Weight ( lb / gal )
Desired Mud Weight ( lb / gal )
Cut Back Mud Weight ( lb / gal )
Volume Of Cut Back Mud Needed
Total Volume After Weigh Up
ormation In Highlighted Areas
EFERENCE ONLY
luid Weigh Up KCL
( Weigh Up Wt. - Desired Wt. ) x 3.5 x Fluid Volume x Percent Desired / Sack Size
Volume To Weigh Up Percent Desired 5.00
300.00 Fluid Weight ( lb / gal ) 8.30
12.00 Sack Size ( lb ) 50.00
12.10 Fluid Volume ( bbl ) 60.00
14.20 Sacks Required 21.00
h Up Mud Needed 14.29 Final Weight 8.52
After Weigh Up 314.29
Fluid Cut Back CaCl2 Weigh Up ( Using 94-97% CaCl2 )
( Desired Wt. - Cut Back Wt. ) x ( Desired Wt. - Original Wt. ) x ( 7 ) x ( Volume ) / 80 x 10
Volume To Cut Back Original Fluid Wt. ( lb / gal ) 9.90
12.00 Desired Weight ( lb / gal ) 10.50
11.60 Fluid Volume ( bbl ) 100.00
10.30 Sacks Required 52.50
8.33 Final Fluid Volume 105.00
Back Mud Needed 7.92
After Weigh Up 19.92 CaBr2 & ZnBr2 Weigh Up ( Using 94-97% CaCl2 )
( Desired Wt. - Original Wt. ) x ( 13 ) x ( Volume ) / 80 x 10
Original Fluid Wt. ( lb / gal ) 12.10
Desired Weight ( lb / gal ) 12.30
Fluid Volume ( bbl ) 500.00
Sacks Required 162.50
Final Fluid Volume 515.48

CaBr2 & ZnBr2 Weigh Up ( Using 95% CaBr2 )

( Desired Wt.-Original Wt. ) x ( 11.5 ) x ( Volume ) / 55 x ( 10 )
Original Fluid Wt. ( lb / gal ) 14.00
Desired Weight ( lb / gal ) 14.20
Fluid Volume ( bbl ) 250.00
Sacks Required 104.55
Final Fluid Volume 255.23
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
1 Cubic Foot Sand = 100# Sand Slurry Convertion
1 Pound Sand = .0456 Gallon Yield Of Slurry After Adding Sand
1 + ( .0456 x Concentration Of Sand Pound Per Gallon Slurry )
Concentration Of Sand - Pound Per Gallon Slurry
Carrier Fluid Weight Lb./ Gal.
Yield Of Slurry Per Gallon Carrier Fluid
Fluid Weight Of Slurry Lb./ Gal.
(Carrier Fluid Weight Lb. Gal. + Concentration Of Sand Pound Per Gallon
Slurry ) / Yield Of Slurry Per Gallon Carrier Fluid
Fluid Weight Of Slurry Lb./ Gal.

Wash Pipe / Screen Ratio ( Optimum Is 80% )

Wash Pipe OD / Screen ID = Ratio
Wash Pipe OD 2.875
Ratio
Screen ID x 80% = Optimum Wash Pipe OD
Optimum Wash Pipe OD

Minimum Clearance For Gravel Pack Completions

Proposed Pumping Rate ( BPM )
Casing ID
Completion OD

Sand Size 8/10

Gravel Pack Sand Grain Size

Note: Fluid Velocity Must Be Less Than 60 FPS To Avoid Tool Erosion.

Fluid Velocity ( FPS )

Minimum Clearance Represents The Minimum Needed To Safely Pump
The Job.
Minimum Allowable Clearance
Minimum Allowable Radial Clearance
Current Completion Clearance
Clearance
Radial Clearance
ormation In Highlighted Areas
EFERENCE ONLY
Slurry Convertion Drift Plate Tolerance
Slurry After Adding Sand Assembly Minimum ID 1.875 ###
ation Of Sand Pound Per Gallon Slurry ) Order Drift Plate 1.870 To 1.860
Pound Per Gallon Slurry 15 ###
Weight Lb./ Gal. 10 ###
Gallon Carrier Fluid 1.684 ###
eight Of Slurry Lb./ Gal. ###
al. + Concentration Of Sand Pound Per Gallon ###
Of Slurry Per Gallon Carrier Fluid ###
f Slurry Lb./ Gal. 14.85 ###
###
een Ratio ( Optimum Is 80% ) ###
pe OD / Screen ID = Ratio ###
Screen ID 3.5 ###
82% ###
80% = Optimum Wash Pipe OD
2.800

ce For Gravel Pack Completions

10.00
8.921
8.750
8/10
1.00

0.094
e Less Than 60 FPS To Avoid Tool Erosion.

56.778
sents The Minimum Needed To Safely Pump
The Job.
1.316
adial Clearance 0.085
t Completion Clearance
0.171
0.085
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
To Locate Leak ( Different Wt. Fluids Tbg. / Csg. )

Psi Differential 500 Leak Depth

Fluid Wt. # 1(Heaviest) 10 13,749
Fluid Wt. # 2(Lightest) 9.3
ormation In Highlighted Areas
EFERENCE ONLY
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Velocity Of Fluid Across Packer Elements
Casing ID In. 8.681

Packer OD In. 8.47

Length Of Packer Element In. 12

Pumping / Circulation Rate Bpm 2

Fluid Weight Ppg 9.3

Conversion Data
1 Barrel = 5.61458 Cu. / Ft.
1 Gallon = 0.133681 Cu. / Ft.

Casing Capacity Bbl. / Ft. 0.0732

Fluid Velocity Going By Elements Fps 9.48

Equivalent Pipe Speed Min. / Std. 3.60

Pressure Dropped Created Psi 56

Force On Packer Elements Lbs. 37,788

Trying To Push Them Out
ormation In Highlighted Areas
EFERENCE ONLY
m/s
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Piston Force Exerted
Piston Area x Pressure = Force
Piston Area Pressure Force
3.1416 10 31.416
(OD2 Piston x .7854) x Pressure =Force
Piston O.D. Pressure Force
2 10 31.42

Piston Pressure Created

Force / (OD2 Piston x .7854) =Pressure
Force Piston O.D. Pressure
31.42 2 10.00
ormation In Highlighted Areas
EFERENCE ONLY
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Hydrostatic Pressure
Fluid Gradient x TVD = Hydrostatic Psi
Fluid Gradient TVD Hyd. Psi
0.433 10,000 4330.00
Fluid Wt. x .05195 x TVD = Hydrostatic Psi
Fluid Wt.lb./ gal. TVD Hyd. Psi
8.550 10725 4763.75
Fluid Wt.lb./ ft.3 x 0.00694 x TVD = Hydrostatic Psi
Fluid Wt.lb./ ft.3 TVD Hyd. Psi
100.000 5000 3472.00

Fluid Weight Required For BHP @ Depth

BHP / ( .05195 x TVD )
BHP 5000 Fluid Wt. lb./ gal.
TVD 10000 9.62

Maximum Allowable Pump Pressure

Fluid Wt.lb./ gal. 8.555 Hyd. Psi Buoyant

Depth 11718 5207.86 Force
Pipe OD 2.875 Area 9436.80
Pipe ID 2.441 1.812 Tbg Wt. Air
Pipe Air Wt.lb./ ft. 6.5 O.D. Area 76167
Tbg. Wt. In Fluid 66730.20 6.492
Max. Pump Psi 10279.12

Tbg. Wt.lb./ ft. Air 6.5 Tbg. Wt. In Fluid

Buoyancy Factor 0.8727 28362.75
Tbg. Length 5000 Tbg. OD Area
Pipe OD 2.875 6.492
Max. Pump Psi 4369.00
ormation In Highlighted Areas
EFERENCE ONLY
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Triplex Pump Output Barrels Per Stroke
( ID x ID X Stoke Length x .000243 ) x Pump Efficiency / 100
Piston OD ( in ) 3.375
Stroke Length ( in ) 8.00
Pump Effeciency ( % ) 80.00
Barrel Per Stroke Output 0.0177
ormation In Highlighted Areas
EFERENCE ONLY
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Maximum Leakage Rate of SCSSV and Plugs Recommended Control Line Hold Open Pressure
MMS Maximum Allowable Leakage Rate is 5 SCF per minute gas and 200 cc SHUT IN
per minute liquid Valve Opening Psi + SITP + 750 Psi
GAS Opening Pressure Off Certification Sheet
(( 4x Psi Increase) x ((( Tubing ID2 ) x 0.005454 ) xDepth )) / Test Length Shut In Tubing Pressure
Tubing ID 2.441 Recommended Hold Open Pressure
Depth 500 Note: SCSSV Hold Open Pressure Should Be Adjusted After Well Is
Pressure Increase 50 Flowing And Stable
Length Of Test In Minute 15 FLOWING
SCF Per Hour 216.65 Valve Opening Psi + Flowing Tubing Psi + 750 Psi
SCF Per Minute 3.61 Opening Pressure Off Certification Sheet
Liquid Flowing Tubing Pressure
Liquid Recovered CC Per Min. Leakage Recommended Open Pressure
CC 1,000.00 66.67
Once 50 98.58 Control Line Fluid Volume
Length Of Test In Minutes 15 OD 0.250
Wall Thickness 0.049
Maximum Fail-Closed Setting Depth Length Ft. 500
Valve Closing Psi / ( Fluid Gradient x Safety Factor ) ID 0.152
Closing Pressure Off Certification Sheet 875 Total Volume Gallons
Fluid Gradient 0.35 Quarts 1.885
Safety Factor 1.25 Pints 3.771
Maximum Fail-Closed Depth 2000
EnerPac P-391 Hand Pump Strokes Required
Specific Gravity To Gradient To Displace Control Line
S.G. x .433 = Gradient
Specific Gravity 0.87 Gradient 0.377 EnerPac P-391 Hand Pump
Oil Volume Per Stroke Cu./ In.
Strokes Per Gallon
Strokes Per Quart
Strokes Per Pint
Strokes Per Cup
Strokes Per Ounce
ormation In Highlighted Areas
EFERENCE ONLY
ontrol Line Hold Open Pressure
SHUT IN
ening Psi + SITP + 750 Psi
Off Certification Sheet 1100
ing Pressure 5000
6850
Pressure Should Be Adjusted After Well Is
lowing And Stable
FLOWING
Psi + Flowing Tubing Psi + 750 Psi
Off Certification Sheet 100
bing Pressure 2500
3350

ol Line Fluid Volume

Area - Sq./ In.
0.018
Gallon Per Foot
0.001
0.471
Cups 7.541
Ounces 60.329

Pump Strokes Required

721
Control Line

ac P-391 Hand Pump

0.151
1530
382
191
96
12
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
To Calculate Pin Shear Force
( OD2 x .7854 ) x Ultimate Shear Strength
Pin OD 0.25 Shear Force
50,000
Ultimate Shear Strength 4,909
Number Of Pins 2
To Calculate Pin Ultimate Shear Strength
Shear Force / ( OD2 x .7854 )
Pin OD 0.25 UltimateShear Strength
Shear Force 5,000 101,859

Pressure Required To Shear Pins

Cross-Sectional Area ( Seal Assy. Inserted )
((ID2 - ID2 ) x .7854 = Area
Receptacle ID 3.880 Piston Area
Seal Assy. ID 0.000 11.824
Pin Shear Value 6,100 Pressure To Shear
Quantity Of Pins 12 6,191
Steel Pin Test Pressure =Pressure To Shear x 70%
Steel Pin Test Pressure 4,334
Brass Pin Test Pressure =Pressure To Shear x 50%
Brass Pin Test Pressure 3,095
ormation In Highlighted Areas
EFERENCE ONLY
 Enter Necessary Information In Highlighted Areas
FOR REFERENCE ONLY
Area Of A Slickline Wire Weight
OD2 x .7854 = Area ( OD2 x 8 ) / 3 = Lbs./ Ft.
Wire Size 0.092 Area 0.0066 Wire Size 0.092 Lb./ Ft. 0.02257
(( OD x 8 ) / 3) x Length = Total Weight.
2

Tool String Balance Weight Neglecting Friction Length 13800 Total Weight
( OD2 x .7854 ) x Pressure = Tool Sting Weight ( balanced ) 311.48
Wire Size 0.092 Tool String Weight
Pressure 1500 9.97
Wire Weight Balance Depth
Stem Weight .2945 x Pressure = Depth
( OD2 x 8 ) / 3 = Lbs./ Ft. Pressure 1500 Depth
OD 1.5 Lb./ Ft. 6.00 441.75
OD x OD x 2.667 = Lbs./ Ft.
OD 1.25 Lb./ Ft. 4.17 Wire Strength ( approximate / standard plow steel )
( OD2 x .7854 ) x 280000 = Approximate Maximum Breaking Strength
Stem Length Needed Neglecting Friction Wire Size 0.092
Stem Weight Needed / Stem Weight lb./ ft. Approximate Max. Strength 1861
Weight Needed 10 Length Needed Ft. (( OD2 x .7854 ) x 280000)*.85 = Approximate Minimum Breaking Strength
Stem Weight lb./ ft. 6 1.667 Wire Size 0.092
Approximate Min. Strength 1582
Minimum Bending Diameter Of Wire
Spool Capacity
NOTE: Larger sheaves, wheels or pulleys could extend cable / wire life. Reference Only ( Assumes Wire Is Perfectly Spooled
Stranded, Braided or Conductor Cables (Drum Width x ( Flange OD - Drum OD ) / 2 ) x ( Drum OD + ( Flange OD -
Diameter of Cable X 64 = Minimum Bending Diameter In Inches Drum OD ) / 2 ) / (( 4 x ( Wire OD )))
Cable Diameter Minimum Diameter In. Enter All Information In Inches
1 /2 32 Drum Width Between Flanges 31
3 /4 48 Flange OD 29
6 /8 48 Drum OD 14
3 /16 12 Wire OD ( Decimal ) 0.25
6 /32 12 Spool Capacity Ft. 19,995
12 /64 12
Slickline Wire ( Piano, Solid )
Diameter of Wire X 120 = Minimum Bending Diameter In Inches
Wire Size Minimum Diameter In.
0.092 11.04
as

Tubing Fill-Up Rule Of Thumb

ID2 = Barrels Per 1000'
Tbg. ID 2.441 Bbl./ 1000' 6.0
###
Hydrostatic Rule Of Thumb
.052 x Lb./ Gal. x Depth
Depth 13800 Hydrostatic Pressure
Fluid Wt. Lb./ Gal. 8.6 6171.36
###
Rule Of Thumb For WireLine Fall-Back
Top Of Rope Socket Left In Hole 13,800 ###
Length Of Wire Left In Hole Ft. 13,400 ###
.092 Wire In 2 7/8" Tubing ###
7
Wire & Tubing Size
###
Wire Fall Back Ft. Per 1,000' 12 ###
Wire Fall Back Total Footage 160.8 ###

Top Of Wire ( Approximate ) 561

###
Area Of Pipe
ID2 x .7854 = Area
Pipe ID 2.441 Area 4.680
###
###
###
###
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Temperature
Average Pipe Temperature
( Surface Temp. + BHT ) / 2
Suface Temp. 50 Average Temp.
BHT 100 75
Change In pipe length ( inches ) due to temperature change
( Pipe length feet x .0000828 ) x Change in pipe temp.
Pipe length 10000 Change in length (inches)
Change in pipe temp. 50 41.40
Change In Average Tubing Temperature
Flowing Condition
((shutin well head temp + static BHT) / 2) - ((flowing WHT+BHT) / 2)
Shutin well head temp 100
Static BHT 200 Change
Flowing well head temp 150 -50
BHT 250
Injecting / Acidizing Condition
((SI WHT + SI BHT) / 2) - ((Surf. Fluid temp. + BHT during inj.) / 2)
Shutin well head temp 100
Shutin BHT 250 Change
Surface fluid temp. 75 62.5
BHT during treatment 150
Converting Temperature Change To Length Change
(Change in Tubing Temperature x Length) x .0000069
Temp. Change 100 Length Change Inches
Tbg. Length 10000 6.90
ormation In Highlighted Areas
EFERENCE ONLY
 Enter Necessary Information In Highlighted Areas
FOR REFERENCE ONLY
To Determine Joint Yield Strength Of EUE Tubing Tubing Capacity
((OD tbg - ID tbg) x .7854) x Grade = Yield
2 2
Tubing Length x Capacity Factor = Capacity Bbl.
Pipe OD 2.375 Yield Tbg. Length Cap. Factor Capacity bbl.
Pipe ID 2.441 105.692 5000 0.00579 28.95
Grade 110 .0009714 x ID2 = Bbl./ Ft.
Tbg. ID 2.441 Bbl./ Ft. 0.00579
Cross-Sectional Area Of Pipe 1029.4 / ID2 = Ft./ Bbl.
((OD2 tbg - ID2 tbg) x .7854 = Area Tbg. ID 2.441 Ft./ Bbl. 172.762
Pipe OD 2.375 Area .005454 x ID2 = Ft.3/ Ft.
Pipe ID 1.995 1.304 Tbg. ID 2.441 Ft.3/ Ft. 0.03250
183.35 / ID2 = Ft./ Ft.2
Tubing Weight Tbg. ID 2.441 Ft./ Ft.3 30.771
In Air ( lb./ ft. ) 24.51 / ID = Ft./ Gal.
2

Tubing Length x Tubing Wt./ Ft. = Total Air Weight Tbg. ID 2.441 Ft./ Gal. 4.1135
Tbg. Length Pipe Wt./ Ft. Total Wt. Tubing Fill-Up Factors
1000 4.7 4,700.00 ( 3.141592654 x ID2 ) / 77 = Fill-Up Factor Gal./ Ft.
In Air ( Does not allow for upsets or couplings ) Tubing I.D. Fill-Up Factor Gal./ Ft.
( OD2 - ID2 ) x 2.67 x Length feet 2.441 0.24310
Pipe OD 2.375 Pipe Weight ( 3.141592654 x ID2 ) / 576 = Fill-Up Factor Ft.3./ Ft.
Pipe ID 1.995 4.43 Tubing I.D. Fill-Up Factor Ft.3/ Ft.
Length 1 2.441 0.03250
In Fluid ( lb./ ft. ) Tubing Fill-Up
Tbg. Air Wt. lb./ ft. x (1- (.01528 x Fluid Wt. lb./ ft.)) Fill-Up Factor x Barrels = Fill-Up Footage
Tbg. Wt.lb./ ft. Air Fluid Wt.lb./ gal. Tbg. Wt. In Fluid Fill-Up Factor Barrel Fill-Up Ft.
6.5 10 5.5068 172.765 10 1,727.65
Buoyancy Factor x Tubing Air Weight = Fluid Weight
Buoyancy Factor Tbg. Air Wt. Tbg. Wt. In Fluid Tubing Displacement
0.8471 4.7 3.98137 Tubing weight lb./ ft. x .0003638 = Displacement bbl./ ft.
Tubing Wt. lb./ ft. 6.5
Buoyancy Factor Displacement bbl./ ft. 0.00236
( 65.42 - Fluid Wt.) / 65.42
Fluid Wt.lb./ gal. 8.33 Factor 0.8727
Tubing Air Wt. x Buoyancy Factor x Length = Tbg. Fluid Wt.
Tbg. Wt.lb./ ft. Air 6.5 Tbg. Wt. In Fluid
Buoyancy Factor 0.8471 5506.15
Tbg. Length 1000

Fluid Wt.lb./ gal. 10 Hyd. Psi Buoyant

Length 500 259.75 Force
Pipe OD 2.875 Area 470.68
Pipe ID 2.441 1.812 Tbg Wt. Air
Pipe Air Wt.lb./ ft. 6.5 3250
Tbg. Wt. In Fluid 2779.32
Bull Plugged In Fluid ( lb./ ft. )

Fluid Wt.lb./ gal. 10 Hyd. Psi Buoyant

Depth 500 259.75 Force
Pipe OD 2.441 Area 1215.58
Pipe Air Wt.lb./ ft. 6.5 4.680 Tbg Wt. Air
Tbg. Wt. In Fluid 2034.42 3250
as

Pipe Stretch
Pull x Depth x 12 / ((( OD2 - ID2 ) x 0.7854 ) x 30000000 ) = Inches
Pull Depth Pipe OD Pipe ID
10000 5000 2.875 2.441
Stretch In Inches 11.04

Slack-Off Data
( Desired Wt. Dwn. / 1000 ) x ( Packer Depth / 1000 ) x Factor
Desired Wt. Down Packer Depth Factor
10000 10000 0.26
Slack-Off In. Required
Factors For Standard Weight Pipe 26
1.900" 0.68
2 3/8" 4.7 # 0.39
2 7/8" 6.5# 0.26
3 1/2" 9.3# 0.17
Factors For Standard Weight Drill Pipe
2 7/8" 10.4# 0.16
3 1/2" 13.3# 0.12
4 1/2" 16.6# 0.11
To Calculate Slack-Off Factor

Pipe OD Pipe ID Slack-Off Factor

2.875 2.441 0.26

Determining Pipe Pull

(( 1000 x 1000) x Stretch Inches) / ( Stretch Factor x Length )
Inches Of Stretch 12 Pipe Pull
Pipe Length 10000 777
Stretch Factor 1.544

Free Pipe Depth

( Stretch Inches x 1000 x 1000) / ( Pull x Factor )
Inches Of Stretch 24 Depth Of Free Pipe
Pull 10000 7742
Stretch Factor 0.31
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Rectangular Volume / Capacity Spherical Volume / Capacity
( In Feet ) Length x Width x Height = Volume Ft3 Diameter3 x .5236 = Volume
Length Ft. 20 Diameter Ft. 20
Width Ft. 10 Volume Ft. 3

Height Ft. 5 1,000.00 Volume Ft3 x .1781 Bbl./ Ft.

Volume Ft3 x .1781 Bbl./ Ft.3 = BBl. Volume Barrels
Volume Barrels 178.10 Total Barrels x 42 = Gallons
Total Barrels x 42 = Gallons Volume Gallons
Volume Gallons 7,480.20
Barrels Total / ( Height feet x 12 ) Pipe / Hose Volume
Barrel Per Inche 2.96833333333333 ID x ID / 1029.4
Barrels Total / Height feet Pipe Or Hose ID
Barrel Per Foot 35.62 Pipe Or Hose Length
Barrel Per Foot
Cylindrical Volume / Capacity Pipe Or Hose Total Volume
( Diameter2 x.7854 ) x Height = Volume
Diameter Ft. 16 Volume Ft.3
Height Ft. 20 4021.248
Volume Ft3 x .1781 Bbl./ Ft.3 = BBl.
Volume Barrels 716.18
Total Barrels x 42 = Gallons
Volume Gallons 30,079.74
Barrels Total / ( Height feet x 12 )
Barrel Per Inche 2.984
Barrels Total / Height feet
Barrel Per Foot 35.809
ormation In Highlighted Areas
EFERENCE ONLY
al Volume / Capacity
eter3 x .5236 = Volume
Volume Ft.3
4188.8
Ft3 x .1781 Bbl./ Ft.3 = BBl.
746.03
Barrels x 42 = Gallons
31,333.06

e / Hose Volume
ID x ID / 1029.4
2.323
15300
Per Foot 0.0052
Total Volume 80.21
 Enter Necessary Information In Highlighted A
FOR REFERENCE ONLY
Stem Weight Tubing Weight With Upsets & Coupling
( OD2 x 8 ) / 3 = Lbs./ Ft. ( OD2 - ID2 ) x .7854 x 0.29665 x 12
OD 2.125 Lb./ Ft. 12.04 Pipe OD 2.875
OD x OD x 2.667 = Lbs./ Ft. Pipe ID 2.441
OD 2.125 Lb./ Ft. 12.04

Calculated I.D.

Pipe OD 2.875
Weight 6.5
I.D. 2.415
Drift 2.290
ormation In Highlighted Areas
EFERENCE ONLY
ht With Upsets & Coupling Area Between Two Circles
D2 ) x .7854 x 0.29665 x 12 ( ID2 x .7854 ) - ( OD2 x .7854 ) = Area Between Circles
Pipe Weight Lb. / Ft. Outer Circle ID 5.000 Area
6.450 Inner Circle OD 4.000 7.069