SiMT341715E Troubleshooting by Remote Controller

3.4 Error Codes and Descriptions

k: ON h: OFF l: Blink
Error code Operation Error contents Reference
lamp page
Indoor Unit A0 l External protection device abnormality 184
A1 l Indoor unit PCB abnormality 185
A3 l Drain level control system (S1L) abnormality 186
A6 l Indoor fan motor (M1F) lock, overload 188
Indoor fan motor abnormality 190
A8 l Power supply voltage abnormality 196
A9 l Electronic expansion valve coil abnormality, dust clogging 199
AF k Humidifier system abnormality 201
AH l Auto grille unit error 202
AJ l Capacity determination device abnormality 203
C1 l Transmission abnormality (between indoor unit PCB and fan PCB) 204
C4 l Indoor heat exchanger liquid pipe thermistor abnormality 209
C5 l Indoor heat exchanger gas pipe thermistor abnormality 209
C6 l Combination abnormality (between indoor unit PCB and fan PCB) 210
Capacity setting abnormality 211
C9 l Suction air thermistor (R1T) abnormality 209
CA k Discharge air thermistor abnormality 209
CE k Infrared presence/floor sensor error 213
CJ k Remote controller thermistor abnormality 218
Outdoor Unit E1 l Outdoor unit main PCB abnormality 219
E2 l Current leakage detection 220
Missing of leakage detection core 221
E3 l Actuation of high pressure switch 222
E4 l Actuation of low pressure sensor 224
E5 l Inverter compressor motor lock 226
E7 l Outdoor fan motor abnormality 228
E9 l Electronic expansion valve coil abnormality 231
F3 l Discharge pipe temperature abnormality 233
F4 l Wet alarm 235
F6 l Refrigerant overcharged 236
H3 l Harness abnormality (between outdoor unit main PCB and inverter PCB) 237
H7 l Outdoor fan PCB abnormality 238
H9 l Outdoor air thermistor (R1T) abnormality 239
J3 l Discharge pipe thermistor (R21T, R22T) abnormality 239
Compressor body thermistor (R8T, R9T) abnormality
J5 l Suction pipe thermistor (R3T) abnormality 239
J7 l Subcooling heat exchanger liquid pipe thermistor (R5T) abnormality 239
J8 l Heat exchanger liquid pipe thermistor (R4T) abnormality 239
J9 l Subcooling heat exchanger gas pipe thermistor (R6T) abnormality 239
JA l High pressure sensor abnormality 241
JC l Low pressure sensor abnormality 242
L1 l Inverter PCB abnormality 243
L2 l Momentary power failure during test operation 245
L4 l Inverter radiation fin temperature rise abnormality 246
L5 l Inverter compressor instantaneous overcurrent 248
L8 l Inverter compressor overcurrent 250
L9 l Inverter compressor startup abnormality 252
LC l Transmission error between inverter PCB and outdoor unit main PCB 255
P1 l Power supply voltage imbalance 257
P3 l Reactor temperature abnormality 259
P4 l Inverter radiation fin temperature abnormality 260
PJ l Field setting after replacing outdoor unit main PCB abnormality or 262
combination of PCB abnormality

Service Diagnosis 171

Troubleshooting by Remote Controller SiMT341715E

k: ON h: OFF l: Blink
Error code Operation Error contents Reference
lamp page
System U0 k Refrigerant shortage 263
U1 l Open phase 264
U2 l Power supply insufficient or instantaneous abnormality 265
U3 l Check operation not executed 267
U4 l Transmission error between indoor units and outdoor units 268
U5 l Transmission error between remote controller and indoor unit 271
U7 l Transmission error between outdoor units 272
U8 l Transmission error between main and sub remote controllers 277
U9 l Transmission error between indoor unit and outdoor unit in the same system 278
UA l Improper combination of indoor unit and outdoor unit, indoor unit and remote 279
controller
UC k Address duplication of centralized controller 282
UE l Transmission error between centralized controller and indoor unit 283
UF l System not set yet 285
UH l System abnormality, refrigerant system address undefined 286

The system operates for error codes indicated in black squares, however, be sure to check and repair.

172 Service Diagnosis

SiMT341715E Troubleshooting by Remote Controller

3.5 Error Codes (Sub Codes)

If an error code like the one shown below is displayed when the navigation remote controller (BRC1E62) is in
use, make a detailed diagnosis or a diagnosis of the relevant unit referring to the attached list of detailed error
codes.

3.5.1 Indoor Unit

Troubleshooting
Error code
Description of error Description of diagnosis
A6 - 01 Fan motor locked A locked fan motor current has been detected.
Turn the fan by hand to check for the connection of
connectors.
A6 - 10 Fan overcurrent error A fan motor overcurrent has been detected.
Check for the connection of the connector between the fan
motor and the PCB for the fan. If the connection is normal,
replace the fan motor. If this still cannot solve the error,
replace the PCB for the fan.
A6 - 11 Fan position detection error An error in the detection of position of the fan motor. Check
for the connection of the connector between the fan motor
and the PCB for the fan. If the connection is normal, replace
the fan motor. If this still cannot solve the error, replace the
PCB for the fan.
A8 - 01 Power supply voltage error Check for the input voltage of the fan motor.
A9 - 01 Electronic expansion valve error There is an error in the electronic expansion valve coil or a
connector disconnected.
A9 - 02 Refrigerant leakage detection error Refrigerant leaks even if the electronic expansion valve is
closed.
Replace the electronic expansion valve.
AH - 03 Transmission error (between the self-cleaning
decoration panel and the indoor unit) Check for the connection of the harness connector between
(when the self-cleaning decoration panel is the panel PCB and the indoor unit PCB.
mounted)
AH - 04 Dust detection sensor error Check for the connections of the connector X12A on the
(when the self-cleaning decoration panel is panel PCB and the connectors X18A and X19A on the
mounted) sensor PCB.
AH - 05 Dust collection sign error Check for clogging with dust at the dust collection port as
(when the self-cleaning decoration panel is well as in the brush unit, S-shaped pipe, and dust box.
mounted) Furthermore, check for any stains of the light receiving and
emitting parts of the infrared unit.
AH - 06 Air filter rotation error Check for anything getting in the way of rotating the filter
(when the self-cleaning decoration panel is (e.g. the filter comes off or the drive gear is clogged with
mounted) foreign matter).
AH - 07 Damper rotation error The damper does not rotate normally. Check for any foreign
(when the self-cleaning decoration panel is matter around the damper and for the operation of the gear
mounted) and limit switch.
AH - 08 Filter self-cleaning operation error The unit has not yet completed the filter self-cleaning
(when the self-cleaning decoration panel is operation even after the lapse of specified period of time.
mounted) Check for any external noise, etc.
AH - 09 Filter self-cleaning operation start disabled error The unit has been put into a state in which the filter self-
(when the self-cleaning decoration panel is cleaning operation is disabled. Check the unit for the
mounted) operating conditions.
AH - 12 Auto grille unit error It is detected that the grille does not operate properly.
(when the auto grille unit is mounted) Check whether the grille does not contact with something or
the wire does not snaggle.
AJ - 01 Capacity setting error There is an error in the capacity setting of the indoor unit
PCB.
AJ - 02 Electronic expansion valve setting error There is a fault in the setting of the gear type electronic
expansion valve/direct acting type electronic expansion
valve.
C1 - 01 Transmission error (between indoor unit PCB Check for the conditions of transmission between the indoor
and the PCB for the fan) unit PCB and the PCB for the fan.
C6 - 01 Defective combination of indoor unit PCB and the A combination of indoor unit PCB and the PCB for the fan is
PCB for the fan defective. Check whether the capacity setting adaptor is
correct and the type of the PCB for the fan is correct.
U4 - 01 Indoor-Outdoor transmission error Refer to the U4 flow chart.
UA - 13 Refrigerant type error The type of refrigerant used for the indoor unit is different
from that used for the outdoor unit.
UA - 15 Not applicable for self-cleaning decoration panel An outdoor unit is not applicable for the self-cleaning
(when the self-cleaning decoration panel is decoration panel is connected.
mounted)
As there are various combinations of indoor and outdoor units, the sub codes of A0 - A3 are not shown in this
table.

Service Diagnosis 173

Troubleshooting by Remote Controller SiMT341715E

3.5.2 Outdoor Unit, System

Troubleshooting
Error code
Description of error Description of diagnosis
E1 - 01 Outdoor unit PCB error Refer to the E1 flowchart of each manual and make a diagnosis
E1 - 02 Defective outdoor unit PCB of the relevant unit based on the Error code shown to the left.
E2 - 01 Earth leakage detection error (Master)
E2 - 02 Earth leakage detection error (Slave 1)
E2 - 03 Earth leakage detection error (Slave 2)
E2 - 06 Missing of earth leakage detection core Refer to the E2 flowchart of each manual and make a diagnosis
(Master) of the relevant unit based on the Error code shown to the left.
E2 - 07 Missing of earth leakage detection core
(Slave 1)
E2 - 08 Missing of earth leakage detection core
(Slave 2)
E3 - 01 High pressure switch activated (Master)
E3 - 02 High pressure switch activated (Master)
E3 - 03 High pressure switch activated (Slave 1)
E3 - 04 High pressure switch activated (Slave 1)
E3 - 05 High pressure switch activated (Slave 2)
E3 - 06 High pressure switch activated (Slave 2)
Refer to the E3 flowchart of each manual and make a diagnosis
E3 - 20 High pressure switch activated (Master) of the relevant unit based on the Error code shown to the left.
E3 - 21 High pressure switch activated (Slave 1)
E3 - 22 High pressure switch activated (Slave 2)
E3 - 07 High pressure switch activated (Batch)
E3 - 13 Liquid stop valve check error (Master)
E3 - 14 Liquid stop valve check error (Slave 1)
E3 - 15 Liquid stop valve check error (Slave 2)
E4 - 01 Low pressure error (Master)
Refer to the E4 flowchart of each manual and make a diagnosis
E4 - 02 Low pressure error (Slave 1) of the relevant unit based on the Error code shown to the left.
E4 - 03 Low pressure error (Slave 2)
E5 - 01 Inverter compressor M1C lock (Master)
E5 - 02 Inverter compressor M1C lock (Slave 1)
E5 - 03 Inverter compressor M1C lock (Slave 2) Refer to the E5 flowchart of each manual and make a diagnosis
E5 - 07 Inverter compressor M2C lock (Master) of the relevant unit based on the Error code shown to the left.
E5 - 08 Inverter compressor M2C lock (Slave 1)
E5 - 09 Inverter compressor M2C lock (Slave 2)
E7 - 01 Fan motor M1F lock (Master)
Refer to the following to make a diagnosis of the fan motor of the
E7 - 02 Fan motor M2F lock (Master) relevant unit.
E7 - 05 Fan motor M1F instantaneous overcurrent (Master)
E7 - 06 Fan motor M2F instantaneous overcurrent (Master)
E7 - 09 Fan motor M1F IPM error (Master)
E7 - 10 Fan motor M2F IPM error (Master)
E7 - 13 Fan motor M1F lock (Slave 1) For fan motor lock, refer to E7-01, -02, -13, -14, -25, and -26.
E7 - 14 Fan motor M2F lock (Slave 1)
E7 - 17 Fan motor M1F instantaneous overcurrent (Slave 1)
E7 - 18 Fan motor M2F instantaneous overcurrent (Slave 1)
E7 - 21 Fan motor M1F IPM error (Slave 1)
For instantaneous overcurrent, refer to E7-05, -06, -17, -18, -29,
E7 - 22 Fan motor M2F IPM error (Slave 1) and -30.
E7 - 25 Fan motor M1F lock (Slave 2)
E7 - 26 Fan motor M2F lock (Slave 2)
E7 - 29 Fan motor M1F instantaneous overcurrent (Slave 2)
E7 - 30 Fan motor M2F instantaneous overcurrent (Slave 2)
E7 - 33 Fan motor M1F IPM error (Slave 2)
For IPM error, refer to E7-09, -10, -21, -22, -33, and -34.
E7 - 34 Fan motor M2F IPM error (Slave 2)

174 Service Diagnosis

SiMT341715E Troubleshooting by Remote Controller

Troubleshooting
Error code
Description of error Description of diagnosis
E9 - 01 Electronic expansion valve coil Y1E error (Master)
E9 - 03 Electronic expansion valve coil Y2E error (Master)
E9 - 05 Electronic expansion valve coil Y1E error (Slave 1)
E9 - 06 Electronic expansion valve coil Y2E error (Slave 1)
E9 - 08 Electronic expansion valve coil Y1E error (Slave 2)
E9 - 09 Electronic expansion valve coil Y2E error (Slave 2)
E9 - 26 Electronic expansion valve coil Y4E error (Master)
E9 - 27 Electronic expansion valve coil Y4E error (Slave 1)
E9 - 28 Electronic expansion valve coil Y4E error (Slave 2) Refer to the E9 flowchart of each manual and make a diagnosis
of the relevant electronic expansion valve of the relevant unit
E9 - 48 Electronic expansion valve overcurrent (Master) based on the Error code shown to the left.
E9 - 49 Electronic expansion valve overcurrent (Slave 1)
E9 - 50 Electronic expansion valve overcurrent (Slave 2)
E9 - 51 Electronic expansion valve fuse thermal cutting (Master)
E9 - 52 Electronic expansion valve fuse thermal cutting (Slave 1)
E9 - 53 Electronic expansion valve fuse thermal cutting (Slave 2)
E9 - 54 Defective circuit (Master)
E9 - 55 Defective circuit (Slave 1)
E9 - 56 Defective circuit (Slave 2)
F3 - 01 Discharge pipe high temperature error (Master)
F3 - 03 Discharge pipe high temperature error (Slave 1)
F3 - 05 Discharge pipe high temperature error (Slave 2) Refer to the F3 flowchart of each manual and make a diagnosis
F3 - 20 Compressor overheat error (Master) of the relevant unit based on the Error code shown to the left.
F3 - 21 Compressor overheat error (Slave 1)
F3 - 22 Compressor overheat error (Slave 2)
F4 - 02 Wet alarm for inverter compressor M1C (Master)
F4 - 03 Wet alarm for inverter compressor M2C (Master)
F4 - 04 Wet alarm for inverter compressor M1C (Slave 1)
F4 - 05 Wet alarm for inverter compressor M2C (Slave 1)
F4 - 06 Wet alarm for inverter compressor M1C (Slave 2)
F4 - 07 Wet alarm for inverter compressor M2C (Slave 2)
F4 - 08 Wet error for inverter compressor M1C (Master) Refer to the F4 flowchart of each manual and make a diagnosis
of the relevant unit based on the Error code shown to the left.
F4 - 09 Wet error for inverter compressor M2C (Master)
F4 - 10 Wet error for inverter compressor M1C (Slave 1)
F4 - 11 Wet error for inverter compressor M2C (Slave 1)
F4 - 12 Wet error for inverter compressor M1C (Slave 2)
F4 - 13 Wet error for inverter compressor M2C (Slave 2)
F4 - 14 Indoor unit failure alarm

Service Diagnosis 175

Troubleshooting by Remote Controller SiMT341715E

Troubleshooting
Error code
Description of error Description of diagnosis
F6 - 02 Excess refrigerant charge error Excess refrigerant charge was detected during test run.
F6 - 03 Excess refrigerant charge warning Excess refrigerant charge was detected during operation other
than test run.
H3 - 02 Connection error between main PCB and
inverter PCB 1 (Master)
H3 - 03 Connection error between main PCB and
inverter PCB 2 (Master)
H3 - 04 Connection error between main PCB and
inverter PCB 1 (Slave 1) Refer to the H3 flowchart of each manual and make a diagnosis
H3 - 05 Connection error between main PCB and of the relevant unit based on the Error code shown to the left.
inverter PCB 2 (Slave 1)
H3 - 06 Connection error between main PCB and
inverter PCB 1 (Slave 2)
H3 - 07 Connection error between main PCB and
inverter PCB 2 (Slave 2)
H7 - 21 Defective fan PCB for M1F (A7P) (Master)
H7 - 22 Defective fan PCB for M2F (A4P) (Master)
H7 - 23 Defective fan PCB for M1F (A7P) (Slave 1) Refer to the H7 flowchart of each manual and make a diagnosis
H7 - 24 Defective fan PCB for M2F (A4P) (Slave 1) of the relevant unit based on the Error code shown to the left.
H7 - 25 Defective fan PCB for M1F (A7P) (Slave 2)
H7 - 26 Defective fan PCB for M2F (A4P) (Slave 2)
H9 - 01 Defective outdoor air thermistor (Master)
Refer to the H9 flowchart of each manual and make a diagnosis
H9 - 02 Defective outdoor air thermistor (Slave 1) of the relevant unit based on the Error code shown to the left.
H9 - 03 Defective outdoor air thermistor (Slave 2)
J3 - 16 Defective discharge pipe 1 thermistor: Open
(Master)
J3 - 17 Defective discharge pipe 1 thermistor: Short
(Master)
J3 - 18 Defective discharge pipe 2 thermistor: Open
(Master)
J3 - 19 Defective discharge pipe 2 thermistor: Short
(Master)
J3 - 22 Defective discharge pipe 1 thermistor: Open
(Slave 1)
J3 - 23 Defective discharge pipe 1 thermistor: Short
(Slave 1)
J3 - 24 Defective discharge pipe 2 thermistor: Open
(Slave 1)
J3 - 25 Defective discharge pipe 2 thermistor: Short
(Slave 1)
J3 - 28 Defective discharge pipe 1 thermistor: Open
(Slave 2) Refer to the J3 flowchart of each manual and make a diagnosis
of the relevant compressor of the relevant unit based on the Error
J3 - 29 Defective discharge pipe 1 thermistor: Short code shown to the left.
(Slave 2)
J3 - 30 Defective discharge pipe 2 thermistor: Open
(Slave 2)
J3 - 31 Defective discharge pipe 2 thermistor: Short
(Slave 2)
J3 - 38 Defective compressor body thermistor for
M1C: Open (Master)
J3 - 39 Defective compressor body thermistor for
M1C: Short (Master)
J3 - 42 Defective compressor body thermistor for
M1C: Open (Slave 1)
J3 - 43 Defective compressor body thermistor for
M1C: Short (Slave 1)
J3 - 44 Defective compressor body thermistor for
M1C: Open (Slave 2)
J3 - 45 Defective compressor body thermistor for
M1C: Short (Slave 2)

176 Service Diagnosis

SiMT341715E Troubleshooting by Remote Controller

Troubleshooting
Error code
Description of error Description of diagnosis
J3 - 47 Defective compressor body thermistor for
M2C: Open (Master)
J3 - 48 Defective compressor body thermistor for
M2C: Short (Master)
J3 - 49 Defective compressor body thermistor for
M2C: Open (Slave 1)
J3 - 50 Defective compressor body thermistor for Refer to the J3 flowchart of each manual and make a diagnosis
M2C: Short (Slave 1) of the relevant compressor of the relevant unit based on the Error
J3 - 51 Defective compressor body thermistor for code shown to the left.
M2C: Open (Slave 2)
J3 - 52 Defective compressor body thermistor for
M2C: Short (Slave 2)
J3 - 56 Discharge pipe warning (Master)
J3 - 57 Discharge pipe warning (Slave 1)
J3 - 58 Discharge pipe warning (Slave 2)
J5 - 01 Defective suction pipe thermistor (Master) Refer to the J5 flowchart of each manual and make a diagnosis
J5 - 03 Defective suction pipe thermistor (Slave 1) of the relevant thermistor of the relevant unit based on the Error
code shown to the left.
J5 - 05 Defective suction pipe thermistor (Slave 2)
J7 - 06 Defective subcooling heat exchanger liquid
pipe thermistor (Master)
Refer to the J7 flowchart of each manual and make a diagnosis
J7 - 07 Defective subcooling heat exchanger liquid of the relevant thermistor based on the Error code shown to the
pipe thermistor (Slave 1) left.
J7 - 08 Defective subcooling heat exchanger liquid
pipe thermistor (Slave 2)
J8 - 01 Defective heat exchanger liquid pipe
thermistor (Master)
J8 - 02 Defective heat exchanger liquid pipe Refer to the J8 flowchart of each manual and make a diagnosis
thermistor (Slave 1) of the relevant thermistor of the relevant unit based on the Error
code shown to the left.
J8 - 03 Defective heat exchanger liquid pipe
thermistor (Slave 2)
J9 - 01 Defective subcooling heat exchanger outlet
thermistor (Master)
J9 - 02 Defective subcooling heat exchanger outlet
thermistor (Slave 1)
J9 - 03 Defective subcooling heat exchanger outlet
thermistor (Slave 2) Refer to the J9 flowchart of each manual and make a diagnosis
of the relevant thermistor based on the Error code shown to the
J9 - 08 Error detection of subcooling heat left.
exchanger outlet pipe thermistor (Master)
J9 - 09 Error detection of subcooling heat
exchanger outlet pipe thermistor (Slave 1)
J9 - 10 Error detection of subcooling heat
exchanger outlet pipe thermistor (Slave 2)
JA - 06 Defective high pressure sensor: Open
(Master)
JA - 07 Defective high pressure sensor: Short
(Master)
JA - 08 Defective high pressure sensor: Open
(Slave 1) Refer to the JA flowchart of each manual and make a diagnosis
JA - 09 Defective high pressure sensor: Short of the relevant sensor based on the Error code shown to the left.
(Slave 1)
JA - 10 Defective high pressure sensor: Open
(Slave 2)
JA - 11 Defective high pressure sensor: Short
(Slave 2)
JC - 06 Defective low pressure sensor: Open (Master)
JC - 07 Defective low pressure sensor: Short (Master)
JC - 08 Defective low pressure sensor: Open (Slave 1) Refer to the JC flowchart of each manual and make a diagnosis
JC - 09 Defective low pressure sensor: Short (Slave 1) of the relevant sensor based on the Error code shown to the left.
JC - 10 Defective low pressure sensor: Open (Slave 2)
JC - 11 Defective low pressure sensor: Short (Slave 2)

Service Diagnosis 177

Troubleshooting by Remote Controller SiMT341715E

Troubleshooting
Error code
Description of error Description of diagnosis
L1 - 01 IPM error: Inverter compressor M1C
(Master)
L1 - 02 Defective current sensor: Inverter
compressor M1C (Master)
L1 - 03 Current offset: Inverter compressor M1C
(Master)
L1 - 04 IGBT error: Inverter compressor M1C
(Master)
L1 - 05 Jumper settings error: Inverter compressor
M1C (Master)
L1 - 07 IPM error: Inverter compressor M1C (Slave 1) The inverter PCB may be defective or a PCB other than the
L1 - 08 Defective current sensor: Inverter specified is mounted.
compressor M1C (Slave 1) Refer to the L1 flowchart of each manual and make a diagnosis
of the relevant unit based on the Error code shown to the left.
L1 - 09 Current offset: Inverter compressor M1C
(Slave 1)
L1 - 10 IGBT error: Inverter compressor M1C
(Slave 1)
L1 - 11 IPM error: Inverter compressor M1C (Slave 2)
L1 - 12 Defective current sensor: Inverter
compressor M1C (Slave 2)
L1 - 13 Current offset: Inverter compressor M1C
(Slave 2)
L1 - 14 IGBT error: Inverter compressor M1C
(Slave 2)
L1 - 15 Jumper settings error: Inverter compressor
M1C (Slave 1)
L1 - 16 Jumper settings error: Inverter compressor
M1C (Slave 2)
L1 - 17 IPM error: Inverter compressor M2C
(Master)
L1 - 18 Defective current sensor: Inverter
compressor M2C (Master)
L1 - 19 Current offset: Inverter compressor M2C
(Master)
L1 - 20 IGBT error: Inverter compressor M2C
(Master)
L1 - 21 Jumper settings error: Inverter compressor
M2C (Master)
L1 - 22 IPM error: Inverter compressor M2C (Slave 1)
L1 - 23 Defective current sensor: Inverter
compressor M2C (Slave 1) The inverter PCB may be defective or a PCB other than the
specified is mounted.
L1 - 24 Current offset: Inverter compressor M2C Refer to the L1 flowchart of each manual and make a diagnosis
(Slave 1) of the relevant unit based on the Error code shown to the left.
L1 - 25 IGBT error: Inverter compressor M2C
(Slave 1)
L1 - 26 Jumper settings error: Inverter compressor
M2C (Slave 1)
L1 - 36 EEPROM abnormality: Inverter compressor
M1C (Master)
L1 - 37 EEPROM abnormality: Inverter compressor
M2C (Master)
L1 - 38 EEPROM abnormality: Inverter compressor
M1C (Slave 1)
L1 - 39 EEPROM abnormality: Inverter compressor
M2C (Slave 1)
L1 - 40 EEPROM abnormality: Inverter compressor
M1C (Slave 2)
L1 - 41 EEPROM abnormality: Inverter compressor
M2C (Slave 2)

178 Service Diagnosis

SiMT341715E Troubleshooting by Remote Controller

Troubleshooting
Error code
Description of error Description of diagnosis
L1 - 42 IPM error: Inverter compressor M2C (Slave 2)
L1 - 43 Defective current sensor: Inverter
compressor M2C (Slave 2)
L1 - 44 Current offset: Inverter compressor M2C
(Slave 2)
L1 - 45 IGBT error: Inverter compressor M2C
(Slave 2)
L1 - 46 Jumper settings error: Inverter compressor
M2C (Slave 2)
The inverter PCB may be defective or a PCB other than the
L1 - 47 Power supply voltage abnormality: Inverter specified is mounted.
compressor M1C (Master) Refer to the L1 flowchart of each manual and make a diagnosis
L1 - 48 Power supply voltage abnormality: Inverter of the relevant unit based on the Error code shown to the left.
compressor M2C (Master)
L1 - 49 Power supply voltage abnormality: Inverter
compressor M1C (Slave 1)
L1 - 50 Power supply voltage abnormality: Inverter
compressor M2C (Slave 1)
L1 - 51 Power supply voltage abnormality: Inverter
compressor M1C (Slave 2)
L1 - 52 Power supply voltage abnormality: Inverter
compressor M2C (Slave 2)
L2 - 01 Momentary power failure (Master)
L2 - 02 Momentary power failure (Slave 1)
L2 - 03 Momentary power failure (Slave 2) Refer to the L2 flowchart of each manual and make a diagnosis
L2 - 04 Power ON (Master) of the relevant unit based on the Error code shown to the left.
L2 - 05 Power ON (Slave 1)
L2 - 06 Power ON (Slave 2)
L4 - 01 Radiation fin temperature rise: Inverter PCB
for M1C (Master)
L4 - 02 Radiation fin temperature rise: Inverter PCB
for M1C (Slave 1)
L4 - 03 Radiation fin temperature rise: Inverter PCB
for M1C (Slave 2)
L4 - 06 Radiation fin temperature rise: Fan M1F
(Master)
L4 - 07 Radiation fin temperature rise: Fan M2F
(Master)
L4 - 09 Radiation fin temperature rise: Inverter PCB
for M2C (Master) Refer to the L4 flowchart of each manual and make a diagnosis
L4 - 10 Radiation fin temperature rise: Inverter PCB of the relevant unit based on the Error code shown to the left.
for M2C (Slave 1)
L4 - 11 Radiation fin temperature rise: Inverter PCB
for M2C (Slave 2)
L4 - 18 Radiation fin temperature rise: Fan M1F
(Slave 1)
L4 - 19 Radiation fin temperature rise: Fan M2F
(Slave 1)
L4 - 20 Radiation fin temperature rise: Fan M1F
(Slave 2)
L4 - 21 Radiation fin temperature rise: Fan M2F
(Slave 2)

Service Diagnosis 179

Troubleshooting by Remote Controller SiMT341715E

Troubleshooting
Error code
Description of error Description of diagnosis
L5 - 03 Current offset error (Master)
L5 - 05 Current offset error (Slave 1)
L5 - 07 Current offset error (Slave 2)
L5 - 14 Inverter compressor M2C instantaneous Refer to the L5 flowchart of each manual and make a diagnosis
overcurrent (Master) of the relevant unit based on the Error code shown to the left.
L5 - 15 Inverter compressor M2C instantaneous
overcurrent (Slave 1)
L5 - 16 Inverter compressor M2C instantaneous
overcurrent (Slave 2)
L8 - 03 Inverter compressor M1C overcurrent error
(Master)
L8 - 06 Inverter compressor M1C overcurrent error
(Slave 1)
L8 - 07 Inverter compressor M1C overcurrent error
(Slave 2) Refer to the L8 flowchart of each manual and make a diagnosis
of the relevant compressor of the relevant unit based on the Error
L8 - 11 Inverter compressor M2C overcurrent error code shown to the left.
(Master)
L8 - 12 Inverter compressor M2C overcurrent error
(Slave 1)
L8 - 13 Inverter compressor M2C overcurrent error
(Slave 2)
L9 - 01 Inverter compressor M1C startup error
(Master)
L9 - 05 Inverter compressor M1C startup error
(Slave 1)
L9 - 06 Inverter compressor M1C startup error
(Slave 2)
L9 - 10 Inverter compressor M2C startup error
(Master)
L9 - 11 Inverter compressor M2C startup error
(Slave 1)
L9 - 12 Inverter compressor M2C startup error
(Slave 2) Refer to the L9 flowchart of each manual and make a diagnosis
of the relevant compressor of the relevant unit based on the Error
L9 - 13 Inverter compressor M1C output open code shown to the left.
phase (Master)
L9 - 14 Inverter compressor M1C output open
phase (Slave 1)
L9 - 15 Inverter compressor M1C output open
phase (Slave 2)
L9 - 16 Inverter compressor M2C output open
phase (Master)
L9 - 17 Inverter compressor M2C output open
phase (Slave 1)
L9 - 18 Inverter compressor M2C output open
phase (Slave 2)

180 Service Diagnosis

SiMT341715E Troubleshooting by Remote Controller

Troubleshooting
Error code
Description of error Description of diagnosis
LC - 14 Transmission error (Between outdoor units,
inverter PCB 1) (Master)
LC - 15 Transmission error (Between outdoor units,
inverter PCB 1) (Slave 1)
LC - 16 Transmission error (Between outdoor units,
inverter PCB 1) (Slave 2)
LC - 19 Transmission error (Between outdoor units,
fan PCB 1) (Master)
LC - 20 Transmission error (Between outdoor units,
fan PCB 1) (Slave 1)
LC - 21 Transmission error (Between outdoor units,
fan PCB 1) (Slave 2) Refer to the LC flowchart of each manual and make a diagnosis
LC - 24 Transmission error (Between outdoor units, of the relevant unit based on the Error code shown to the left.
fan PCB 2) (Master)
LC - 25 Transmission error (Between outdoor units,
fan PCB 2) (Slave 1)
LC - 26 Transmission error (Between outdoor units,
fan PCB 2) (Slave 2)
LC - 30 Transmission error (Between outdoor units,
inverter PCB 2) (Master)
LC - 31 Transmission error (Between outdoor units,
inverter PCB 2) (Slave 1)
LC - 32 Transmission error (Between outdoor units,
inverter PCB 2) (Slave 2)
P1 - 01 Unbalanced power supply voltage (Master)
P1 - 02 Unbalanced power supply voltage (Slave 1)
P1 - 03 Unbalanced power supply voltage (Slave 2)
P1 - 07 Inverter 2 power supply unbalanced voltage Refer to the P1 flowchart of each manual and make a diagnosis
(Master) of the relevant unit based on the Error code shown to the left.
P1 - 08 Inverter 2 power supply unbalanced voltage
(Slave 1)
P1 - 09 Inverter 2 power supply unbalanced voltage
(Slave 2)
P3 - 01 Defective reactor thermistor 1 (Master:
Inverter PCB 1)
P3 - 02 Defective reactor thermistor 1 (Slave 1:
Inverter PCB 1)
P3 - 03 Defective reactor thermistor 1 (Slave 2:
Inverter PCB 1)
P3 - 04 Defective reactor thermistor 2 (Master:
Inverter PCB 1)
P3 - 05 Defective reactor thermistor 2 (Slave 1:
Inverter PCB 1)
P3 - 06 Defective reactor thermistor 2 (Slave 2:
Inverter PCB 1) Refer to the P3 flowchart of each manual and make a diagnosis
P3 - 07 Defective reactor thermistor 1 (Master: of the relevant unit based on the Error code shown to the left.
Inverter PCB 2)
P3 - 08 Defective reactor thermistor 1 (Slave 1:
Inverter PCB 2)
P3 - 09 Defective reactor thermistor 1 (Slave 2:
Inverter PCB 2)
P3 - 10 Defective reactor thermistor 2 (Master:
Inverter PCB 2)
P3 - 11 Defective reactor thermistor 2 (Slave 1:
Inverter PCB 2)
P3 - 12 Defective reactor thermistor 2 (Slave 2:
Inverter PCB 2)

Service Diagnosis 181

Troubleshooting by Remote Controller SiMT341715E

Troubleshooting
Error code
Description of error Description of diagnosis
P4 - 01 Defective radiation fin thermistor (Master:
Inverter PCB 1)
P4 - 02 Defective fan M1F fin sensor (Master)
P4 - 03 Defective fan M2F fin sensor (Master)
P4 - 04 Defective radiation fin thermistor (Slave 1:
Inverter PCB 1)
P4 - 05 Defective radiation fin thermistor (Slave 2:
Inverter PCB 1)
P4 - 06 Defective radiation fin thermistor (Master: Refer to the P4 flowchart of each manual and make a diagnosis
Inverter PCB 2) of the relevant unit based on the Error code shown to the left.
P4 - 07 Defective radiation fin thermistor (Slave 1:
Inverter PCB 2)
P4 - 08 Defective radiation fin thermistor (Slave 2:
Inverter PCB 2)
P4 - 15 Defective fan M1F fin sensor (Slave 1)
P4 - 16 Defective fan M2F fin sensor (Slave 1)
P4 - 17 Defective fan M1F fin sensor (Slave 2)
P4 - 18 Defective fan M2F fin sensor (Slave 2)
PJ - 04 Incorrect type of inverter PCB 1 (Master)
PJ - 05 Incorrect type of inverter PCB 1 (Slave 1)
PJ - 06 Incorrect type of inverter PCB 1 (Slave 2)
PJ - 09 Incorrect type of fan PCB 1 (Master)
PJ - 10 Incorrect type of fan PCB 2 (Master)
PJ - 12 Incorrect type of inverter PCB 2 (Master) Refer to the PJ flowchart of each manual and make a diagnosis
PJ - 13 Incorrect type of inverter PCB 2 (Slave 1) of the relevant unit based on the Error code shown to the left.
PJ - 14 Incorrect type of inverter PCB 2 (Slave 2)
PJ - 15 Incorrect type of fan PCB 1 (Slave 1)
PJ - 16 Incorrect type of fan PCB 1 (Slave 2)
PJ - 17 Incorrect type of fan PCB 2 (Slave 1)
PJ - 18 Incorrect type of fan PCB 2 (Slave 2)
U0 - 05 Refrigerant shortage warning (cooling)
U0 - 06 Refrigerant shortage warning (heating)
U0 - 08 Refrigerant shortage (Master) Refer to the U0 flowchart of each manual and make a diagnosis
of the relevant unit based on the Error code shown to the left.
U0 - 09 Refrigerant shortage (Slave 1)
U0 - 10 Refrigerant shortage (Slave 2)
U1 - 16 Open phase for power supply (Master)
U1 - 17 Open phase for power supply (Slave 1)
U1 - 18 Open phase for power supply (Slave 2) Refer to the U1 flowchart of each manual and make a diagnosis
U1 - 19 Hz error for power supply (Master) of the relevant unit based on the Error code shown to the left.
U1 - 20 Hz error for power supply (Slave 1)
U1 - 21 Hz error for power supply (Slave 2)
U2 - 01 Shortage of inverter power supply voltage (Master)
U2 - 08 Shortage of inverter power supply voltage (Slave 1)
U2 - 11 Shortage of inverter power supply voltage (Slave 2) Refer to the U2 flowchart of each manual and make a diagnosis
U2 - 22 Shortage of inverter 2 power supply voltage (Master) of the relevant unit based on the Error code shown to the left.
U2 - 25 Shortage of inverter 2 power supply voltage (Slave 1)
U2 - 28 Shortage of inverter 2 power supply voltage (Slave 2)

182 Service Diagnosis

SiMT341715E Troubleshooting by Remote Controller

Troubleshooting
Error code
Description of error Description of diagnosis
U3 - 02 Initial installation alarm / Test operation
failed due to indoor unit error
U3 - 03 Test operation not conducted
U3 - 04 Abnormal end of test operation
U3 - 05 Premature end of test operation during
initial transmission error – check indoor unit
error U4 / U9
Refer to the U3 flowchart of each manual and make a diagnosis
U3 - 06 Premature end of test operation during of the relevant unit based on the Error code shown to the left.
normal transmission error
U3 - 07 Premature end of test operation due to
transmission error
U3 - 08 Premature end of test operation due to
transmission error of all units
U3 - 10 System refrigerant auto charge operation
not yet executed
U4 - 01 Transmission error between indoor and
outdoor units Refer to the U4 flowchart of each manual and make a diagnosis
U4 - 03 Transmission error between indoor unit and of the relevant unit based on the Error code shown to the left.
system: check indoor unit error
U7 - 01 Error when external control adaptor for
outdoor unit is installed
U7 - 02 Alarm when external control adaptor for
outdoor unit is installed
U7 - 03 Transmission error between master and
slave 1 units
U7 - 04 Transmission error between master and Refer to the U7 flowchart of each manual and make a diagnosis
slave 2 units of the relevant unit based on the Error code shown to the left.
U7 - 05 Multi system error
U7 - 06 Error in address settings of slave 1 and 2
U7 - 07 Connection of four or more outdoor units in
the same system
U7 - 11 Error in indoor unit connection capacity for
test operation
U9 - 01 Other indoor units and outdoor unit Refer to the U9 flowchart of each manual and make a diagnosis
abnormality of the relevant unit based on the Error code shown to the left.
UA - 00 TSS plus unit field settings error, CT
address duplication warning
UA - 03 Connection of excessive indoor units
UA - 17 Connection of excess indoor units
UA - 18 Connection of incorrect models of indoor Refer to the UA flowchart of each manual and make a diagnosis
units of the relevant unit based on the Error code shown to the left.

UA - 20 Improper combination of outdoor units

UA - 21 Wrong connection
UA - 31 Multi system combination error
UF - 01 Wrong wiring check error Refer to the UF flowchart of each manual and make a diagnosis
UF - 05 Defective stop valve for test operation of the relevant unit based on the Error code shown to the left.
UH - 01 Wiring error Refer to the UH flowchart of each manual.

Service Diagnosis 183