Secure I/O 2

INSTALLATION GUIDE

Version 2.12
English
EN 101.00.SIO2 V2.12A
 CONTENTS

Safety information 2 Product Specifications 9

Instructional icons 2

FCC compliance information 11

Introduction 4

Components 4
Appendices 12
Name of each part 5
Disclaimers 12

Installation Example 5
Copyright Notice 12

Connections 6

Power 6

RS-485 6
Fail Safe Lock 7
Fail Secure Lock 7

Door button 8

Door sensor 8
Safety information
Please read this safety instructions before you use the product to prevent injury to yourself and others and to prevent
property damage. The term 'product' in this manual refers to the product and any items provided with the product.

Safety information
Instructional icons

Warning: This symbol indicates situations that could result in death or severe injury.

Caution: This symbol indicates situations that may result in moderate injury or property damage.

Note: This symbol indicates notes or additional information.

Warning

Installation
Do not install or repair the product arbitrarily.
• This may result in electric shock, fire, or product damage.
• Damages caused by any modifications or failure to follow installation instructions can void the manufacturer’s warranty.
Do not install the product in a place with direct sunlight, moisture, dust, soot, or a gas leak.
• This may result in electric shock or fire.
Do not install the product in a location with heat from an electric heater.
• This may result in fire due to overheating.
Install the product in a dry location.
• Humidity and liquids may result in electric shock or product damage.
Do not install the product in a location where it will be affected by radio frequencies.
• This may result in fire or product damage.

Operation
Keep the product dry.
• Humidity and liquids may result in electric shock, fire, or product damage.
Do not use damaged power supply adaptors, plugs, or loose electrical sockets.
• Unsecured connections may cause electric shock or fire.
Do not bend or damage the power cord.
• This may result in electric shock or fire.

2
 Safety information

Caution

Installation
Do not install the power supply cable in a location where people pass by.
• This may result in injury or product damage.
Do not install the product near magnetic objects, such as a magnet, TV, monitor (especially CRT), or speaker.
• The product may malfunction.
Secure I/O 2, the electrical locking device and access controller must use independent power source.

Operation
Do not drop the product or cause impacts to the product.
• The product may malfunction.
Do not press buttons on the product by force or do not press them with a sharp tool.
• The product may malfunction.
When cleaning the product, mind the following.
• Wipe the product with a clean and dry towel.
• If you need to sanitize the product, moisten the cloth or the wipe with a proper amount of rubbing alcohol and gently
clean all exposed surfaces including the fingerprint sensor. Use rubbing alcohol (containing 70% Isopropyl alcohol) and a
clean, non-abrasive cloth like lens wipe.
• Do not apply liquid directly to the surface of the product.
Do not use the product for anything other than its intended use.
• The product may malfunction.

3
Introduction

Components

Introduction
Secure I/O 2

Fixing screw x2 Bracket x2 120Ω resistor Diode

• Components may vary according to the installation environment.

4
 Introduction

Name of each part

LED status indicator for RS-485 D- (TRX-)

LED status indicator for Power LED status indicator for RS-485 D+ (TRX+)

Power RS-485 D+ (TRX+)

GND RS-485 D- (TRX-)
LED status indicator for External IN 1 RS-485 GND
External IN 1+ Relay Output Normally Closed
External IN GND Relay Output Common
External IN 2+ Relay Output Normally Open
LED status indicator for External IN 2 INIT button

RESET button
Relay status indication LED

• Press INIT button to reset Secure I/O 2 interworking with a device and then connect to another device.

Installation Example
Secure I/O 2 is connected with RS-485 and can be installed anywhere due to its small size. It can be installed with a
junction box or onto a wall control box already installed. It can be installed at the rear side of an Exit button.

RS-485

External Input

Relay Output

Door lock
Exit button
device Access Controller

5
Connections
• Cable should be AWG22~AWG16.
• To connect the cable to Secure I/O 2, strip off approximately 5~6 mm of the end of the cable and connect

Connections
them.

Power
• Do not share the power with the access controller.
• If the power is shared by other devices, it should provide 9–18V and a minimum of 500 mA.
• When using a power adapter, it should have IEC/EN 62368-1 certification.

DC
Power

RS-485
• RS-485 should be twisted pair, and maximum length is 1.2 km.
• Connect a termination resistor (120Ω) to both ends of a RS-485 daisy chain connection. It should be installed at both
ends of the daisy chain. If it is installed in the middle of the chain, the performance in communicating will deteriorate
because it reduces the signal level.

Termination
resistor RS-485 TRX+ RS-485 TRX-
(120Ω)

Termination
resistor
GND (120Ω)

Access controller
Access controller

6
 Connections

Relay

Fail Safe Lock

In order to use the Fail Safe Lock, connect the N/C relay as shown in the figure below. There is normally a current flowing
through the relay for the Fail Safe Lock. When the relay is activated, blocking the current flow, the door will open. If the
power supply to the product is cut off due to a power failure or an external factor, the door will open.

• Connect a diode to both ends of the power input as shown in the figure below when installing a deadbolt or a
door strike. Make sure to connect the Cathode (direction to the stripe) to the + part of the power while paying
attention to the direction of the diode.

Dead bolt
DC power
/ Door strike

Fail Secure Lock

In order to use the Fail Secure Lock, connect N/O relay as shown in the figure below. There is normally no current
flowing through the relay for the Fail Secure Lock. When the current flow is activated by the relay, the door will open. If
the power supply to the product is cut off due to a power failure or an external factor, the door will lock.

• Connect a diode to both ends of the power input as shown in the figure below when installing a deadbolt or a
door strike. Make sure to connect the Cathode (direction to the stripe) to the + part of the power while paying
attention to the direction of diode.

Dead bolt / DC power

Door strike

7
 Connections

Door button

RTE button
or
Door button

GND

Door

Door sensor

Door Sensor

Door

8
Product Specifications
Category Feature Specification

Product Specifications
Model SIO2
CPU Cortex M3 72 MHz
Memory 128 KB Flash + 20 KB RAM

Multi-color
• PWR
LED • RS-485 TX/RX
• IN1/IN2
General • RELAY

Operating temperature -20°C ~ 50°C

Storage temperature -40°C ~ 70°C
Operating humidity 0% ~ 80%, non-condensing
Storage humidity 0% ~ 90%, non-condensing
Dimension (W x H x D) 36 mm x 65 mm x 18 mm
Weight 37 g
Certificates CE, FCC, KC, RoHS
RS-485 1 ch
Interface TTL Input 2 ch
Relay 1 relay

• Recommended: 9 VDC (130 mA), 12 VDC (100 mA), 18 VDC (70 mA)
Power • Maximum: 18 VDC (200 mA)
Electrical • Current: Maximum 200 mA
2 A@ 30 VDC Resistive load
Relay
1 A@ 30 VDC Inductive load

9
 Product Specifications

Dimensions
(Unit: mm)
* The tolerance is ±0.3 mm.

36 18

2 - 3.2

2 - 4.2

65 83.3 94

10
FCC compliance information
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

FCC compliance information

Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a commercial installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions manual, it may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the interference at his own expense.

• Modifications: Any modifications made to this device that are not approved by Suprema Inc. may void the
authority granted to the user by the FCC to operate this equipment.

11
Appendices

Disclaimers

Appendices
• Information in this document is provided in connection with Suprema products.
• The right to use is acknowledged only for Suprema products included in the terms and conditions of use or sale for
such products guaranteed by Suprema. No license, express or implied, by estoppel or otherwise, to any intellectual
property is granted by this document.
• Except as expressly stated in an agreement between you and Suprema, Suprema assumes no liability whatsoever,
and Suprema disclaims all warranties, express or implied including, without limitation, relating to fitness for a
particular purpose, merchantability, or noninfringement.
• All warranties are VOID if Suprema products have been: 1) improperly installed or where the serial numbers,
warranty date or quality assurance decals on the hardware are altered or removed; 2) used in a manner other than
as authorized by Suprema; 3) modified, altered, or repaired by a party other than Suprema or a party authorized by
Suprema; or 4) operated or maintained in unsuitable environmental conditions.
• Suprema products are not intended for use in medical, lifesaving, life-sustaining applications, or other applications in
which the failure of the Suprema product could create a situation where personal injury or death may occur. Should
you purchase or use Suprema products for any such unintended or unauthorized application, you shall indemnify and
hold Suprema and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs,
damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal
injury or death associated with such unintended or unauthorized use, even if such claim alleges that Suprema was
negligent regarding the design or manufacture of the part.
• Suprema reserves the right to make changes to specifications and product descriptions at any time without notice to
improve reliability, function, or design.
• Personal information, in the form of authentication messages and other relative information, may be stored within
Suprema products during usage. Suprema does not take responsibility for any information, including personal
information, stored within Suprema’s products that are not within Suprema’s direct control or as stated by the
relevant terms and conditions. When any stored information, including personal information, is used, it is the
responsibility of the product users to comply with national legislation (such as GDPR) and to ensure proper handling
and processing.
• You must not rely on the absence or characteristics of any features or instructions marked "reserved" or
"undefined." Suprema reserves these for future definition and shall have no responsibility whatsoever for conflicts or
incompatibilities arising from future changes to them.
• Except as expressly set forth herein, to the maximum extent permitted by law, the Suprema products are sold “as is”.
• Contact your local Suprema sales office or your distributor to obtain the latest specifications and before placing your
product order.

Copyright Notice
Suprema has the copyright of this document. The rights of other product names, brands, and trademarks belong to
individuals or organizations who own them..

12
 Suprema Inc.
17F Parkview Tower, 248, Jeongjail-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, 13554, Rep. of KOREA
Tel: +82 31 783 4502 | Fax: +82 31 783 4503 | Inquiry: [email protected]

For more information about Suprema’s global branch offices,

visit the webpage below by scanning the QR code.
http://www.supremainc.com/en/about/contact-us.asp

© 2021 Suprema Inc. Suprema and identifying product names and numbers herein are registered trade marks of Suprema, Inc.
All non-Suprema brands and product names are trademarks or registered trademarks of their respective companies.
Product appearance, build status and/or specifications are subject to change without notice.