DS-3E1310P-EI/M

8 Port Fast Ethernet Smart PoE Switch

Smart managed switches are developed by Hikvision, featuring easy management and maintenance. You can easily deploy,
monitor and expand your surveillance system anytime and anywhere with our software platforms. You can view the network
topology, monitor the health of the network and receive device alarms in real time, which greatly reduces the cost of
network operation and maintenance.

 8 × 10/100M PoE port,2 × Gigabit RJ45 port

 Total PoE Power Budget 60 W
 Support 802.1Q VLAN
 Support PoE watchdog to detect and restart the cameras that do not respond
 Support STP/RSTP Loop prevention
 Support cable detection to locate failure
 Up to 300 m Long Range PoE Transmission
 6 kV Surge Protection

Specification
Model DS-3E1310P-EI/M
Ports 8 × 10/100 Mbps PoE port,2 × Gigabit RJ45 port
MAC Address Table 4K
Network
Switching Capacity 5.6 Gbps
Parameters
Packet Forwarding Rate 4.17 Mpps
Internal Cache 2 Mbits
PoE Standard IEEE 802.3af,IEEE 802.3at
PoE Power Pin End-span: 1/2(-), 3/6(+)
PoE Power
PoE Port PoE: Ports 1 to 8
Supply
Max. Port Power 30 W
PoE Power Budget 60 W
Ports 1 to 8: up to 300 m.
Long Range
Long range performance may vary depend on camera model or cable condition.
Ports 1 to 8: port isolation mode to improve network security
Port Isolation Ports in an isolation group cannot communicate with each other, but they can
communicate with ports outside the isolation group.
PoE Watchdog Ports 1 to 8: auto detect and restart the cameras that do not respond.
Loop prevention is used to prevent the switching network from forming loops,
which will seriously affect network communication. Disabled by default.
Loop Prevention
Support 802.1D STP.
Suppport 802.1w RSTP.
VLAN is used for network scale planning and network health improvement.
Support 802.1Q.
VLAN Configurable VLAN ID from 1-4094.
Support Trunk, Access port mode.
Support Max. 4094 VLAN.
Support one-click activation and remote management via Hik-Partner Pro.
Software
Functions supported:
Function
1. Display the port rate.
2. Display the port bandwidth utilization rate.
3. Display the PoE power usage.
HPP
4. Display topology information.
5. Display the alarm status.
6. Restart ports and devices.
7. Enable port long-rage mode.
8. Remotely upgrade the device.
Support device management via web.
Support DHCP Client. Enabled by default for dynamic assignment of management
IP addresses.
Support Super IP, which is a fixed IP address (10.180.190.200) for direct access.
System Maintenance
Support management via Hik-Central Pro.
Support remote management via Hik-Partner Pro.
Support cable detection.
Supports 802.1ab LLDP for peer device discovery.
 Support port mirroring for fault locating.
Shell Metal material
Net Weight 0.54 kg (1.19 lb)
Gross Weight 1.08 kg (2.38 lb)
Dimensions (W × H × D) 217.6 mm × 27.6 mm × 108.5 mm (8.57'' × 1.09'' × 4.27'')
Operating Temperature 0 °C to 40 °C (32 °F to 104 °F)
Storage Temperature -40 °C to 85 °C (-40 °F to 185 °F)
General Operating Humidity 5% to 95% (no condensation)
Relative Humidity 5% to 95% (no condensation)
Power Supply DC 54 V,1.2 A
Installation Mode Desk-Mounted,Wall-Mounted
Max. Power Consumption 65 W
Power Consumption in Idle 3.2 W
Surge Protection 6 kV
CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3:
EMC
2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)
CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN
Approval Safety
62368-1: 2014+A11: 2017)
CE-RoHS (2011/65/EU); WEEE (2012/19/EU); Reach (Regulation (EC)
Chemistry
No.1907/2006)


Available Model
DS-3E1310P-EI/M


Typical Application

Physical Interface
Front Panel

Rear Panel

No. Indicator/Port Description

 Solid on: The switch is powered on normally.
① PWR Indicator
 Unlit: No power supply is connected or power supply is abnormal.
 Solid on/Flashing: The output power of the switch is about to reach or has reached the upper limit.
The power supply may be abnormal if more devices are connected.
PoE-MAX
②  Unlit: The switch does not supply power to a powered device (PD), or supplies power to a PD
Indicator
normally and its output power does not reach the upper limit. (The PoE-MAX indicator will be unlit in
5 seconds after the output power of the switch returns to normal.)
 Solid on: The port is connected.
LINK/ACT
③  Flashing: The port is transmitting data.
Indicator
 Unlit: The port is disconnected or connection is abnormal.
 Solid on: The switch supplies power to a PD normally.
④ PoE Indicator
 Unlit: The switch is disconnected from a PD or power supply is abnormal.
10/100 Mbps PoE
⑤ Used for connection to a PD via a network cable.
RJ45 Port
⑥ Gigabit RJ45 Port Used for connection to another device via a network cable.
Press and hold the reset button for about 5 seconds to restore all the configurations of the switch to
⑦ Reset Button
default settings.
Grounding
⑧ Used for connection to the grounding cable to protect the switch from lightning.
Terminal
⑨ Power Supply Use the attached power adapter and AC power cord to connect the switch to a socket.

Dimension