Permanent strand anchor type A2
Retaining walls, slope
• CE anchor head stabilization, anchoring
• Reliable
• Sustainable Technical data sheet reference n°: FT En C IX 1 1 1
The system Tendon
The strand anchor comprises a part contained in a bore The Freyssinet strand anchor comprises a bundle of prestressing strands.
hole (anchor body) and an external part (anchor head) that
connects to the structure.
Yield Ultimate Cross Strand Ultimate Yield load Young
The anchor body is bonded to the ground by injecting Type strength strength section Weight load Fp0,1% modulus
(N/mm²) (N/mm²) (mm²) (kg/m) Fpk (kN) (kN) (kN/mm²)
a cement-based grout. The grout is injected through an
2T15.3 2x0.6" 280 2.18 520 458
additional injection system mounted on the corrugated
3T15.3 3x0.6" 420 3.27 780 687
sheath.
4T15.3 4x0.6" 560 4.36 1.040 916
5T15.3 5x0.6" 700 5.45 1.300 1.145
Anchor head
6T15.3 6x0.6" 840 6.54 1.560 1.374
Over length (Slg)
7T15.3 7x0.6" 980 7.63 1.820 1.603
1.640 1.860 ~196
8T15.3 8x0.6" 1.120 8.72 2.080 1.832
Strands greased 9T15.3 9x0.6" 1.260 9.81 2.340 2.061
and sheathed 10T15.3 10x0.6" 1.400 10.9 2.600 2.290
11T15.3 11x0.6" 1.540 11.99 2.860 2.519
12T15.3 12x0.6" 1.680 13.08 3.120 2.748
13T15.3 13x0.6" 1.820 14.17 3.380 2.977
2T15.7 2x0.62" 300 2.36 558 492
3T15.7 3x0.62" 450 3.54 837 738
Corrugated plastic 4T15.7 4x0.62" 600 4.72 1.116 984
sheath
5T15.7 5x0.62" 750 5.90 1.395 1.230
Free length (Lgl)
6T15.7 6x0.62" 900 7.08 1.674 1.476
7T15.7 7x0.62" 1.050 8.26 1.953 1.722
1.640 1.860 ~196
8T15.7 8x0.62" 1.200 9.44 2.232 1.968
9T15.7 9x0.62" 1.350 10.62 2.511 2.214
10T15.7 10x0.62" 1.500 11.80 2.790 2.460
11T15.7 11x0.62" 1.650 12.98 3.069 2.706
12T15.7 12x0.62" 1.800 14.16 3.348 2.952
Filling pipe 13T15.7 13x0.62" 1.950 15.34 3.627 3.198
Stronger tendons are available upon request. The service load depends on the applicable standard.
Spring basket
(every 2 meters)
Bare strands
Bond length (Lgs)
Anchor foot
Slope stabilization under bridge foundation
FT En C IX 1 1 1 - v1 - 03/13
Permanent strand anchor type A2
Transportation Anchor body type A2
On delivery, anchors Across the free length, the strands are individually covered by a PE D (mm)
are generally wound. sheath and greased. The strands are contained in a plastic corrugated 2T15 60
They can be hanged on sheathing. A filling pipe installed among the strands allows the internal 3T15 65
a recoverable metallic injection of the sheathing with a cement grout when the anchor 4T15 80
frame, is installed in the bore hole. The injection of the external bonding 5T15 80
cement grout is done through an injection system installed outside the 6T15 80
sheathing. On the bond length, spring baskets, installed every 2 meters, 7T15 80
ensure a minimum grout cover of 10 mm. 8T15 100
or on a lost wooden support
9T15 100
or pallet, best solution for
10T15 100
transport in containers or on Spring basket 11T15 100
long distance. 12T15 100
Injection pipes
(optional) 13T15 114
Bare strands External diameter of the anchor
Cross-section of the bond length (excluding injection system)
Plastic corrugated
Greased monostrands
Installation sheathing
An uncoiler can be sent to the site to allow the anchors Cross-section of the free length
to be quickly and safely installed.
Anchor heads
The anchor head consists of a bearing plate with a welded External dimensions of the anchor
trumpet tube, an anchor block, jaws and cap. The trumpet head
and the cap are filled with grease or wax. For re-tensionable e (mm) D (mm) H (mm)
anchor heads, the block is threaded on the outside (to adjust 2 to 4T15 30 220 110
5 to 7T15 35 220 130
or measure the tensile load). A joint creates a seal between
8 and 9T15 35 240 185
the trumpet tube and the corrugated sheath.
10 to 13T15 50 240 200
Note: The stated dimensions correspond to
Freyssinet uncoiler a maximum recess diameter of 170 mm.
The strength of the concrete bearing surface
must be checked separately. If needed, those
Tensioning and testing dimensions can be adapted on request.
D
D
Specific hire equipment is
Smooth block
available for tensioning and
testing the anchors. Freyssinet H H
e e
also offers on-site technical Threaded block
assistance for tensioning and
testing. Where tensioning Trumpet tube
and testing are performed by
Freyssinet, a report is issued
Sealing joint
for each anchor to confirm
compliance with the applicable
Example of report Standard anchor head Re-tensionable anchor head
standard.
Quality insurance
A conformity certificate is sent with each delivery.
FT En C IX 1 1 1 - v1 - 03/13
Head with angular chair
All rights reserved by FREYSSINET. Product names are trademarks of FREYSSINET. The information in this document is subject to change.
Whilst it is as accurate as possible, it is not in any way binding on FREYSSINET.
Freyssinet 1 bis, rue du Petit Clamart - Bât C - 78140 Vélizy-Villacoublay - France • Tel.: +33 1 46 01 84 84 - Fax: +33 1 46 01 85 85 • www.freyssinet.com
