HAINING LONGTIME INDUSTRY CO.
,LTD
ADD: NO.58-1 LINJIACHANG,WANXIN VILLAGE,DINGQIAO TOWN,HAINING CITY ,
ZHEJIANG PROVINCE, CHINA
Tel: 0573-87882633; Fax: 0573-87882633
TECHNICAL PARAMETERS OF HOT STAMPING FOIL
1.0 IDENTIFICATION OF THE SUBSTANCE / PREPARATION AND OF THE COMPANY
1.1 INGREDIENT polyethylene terephthalate
1.2 PRODUCT NAME transfer membrane
1.3 USE OF THE PRODUCT industry usage
1.4 COLOR transparent, white, black, yellow, red, blue and other
color
1.5 ODOR none
The thickness of film : from 0,012 - 0,020mm
2.0 COMPOSITION / INFORMATION ON INGREDIENTS
2.1 CHEMICAL INGREDIENTS
Chemical Ingredients Content Formula CAS. NO.
poly(1-chloroethylene) 50-90 -- 9002-86-2
Resin 10-20 -- --
Pigment 5-10 -- --
2.2 HAZARDS INGREDIENT
No particular hazards ingredient
2.3 CAS. NO.
25038-59-9.
3.0 EMERGENCY OVERVIEW
No particular hazards known. Without stimulate to a human body, may can able to certain
mechanical injury.
In case of fires, hazardous combustion gases are formed.
Material may accumulate a static charge which could lead static discharge.
4.0 FIRST-AID MEASURES
4.1 INGESTION
Without harmful to human, seek medical advice.
4.2 INHALATION
If symptomatic, move to fresh air, and remove inhalation substance.
4.3 EYES
Any material that contacts the eye should be washed out immediately with water. Get medical
attention if symptoms persist.
4.4 SKIN
Fused materials contact skin should be cooled immediately with cooling water and seek medical
advice. Don’t take off directly from skin.
5 FIRE FIGHTING MEASURES
5.1 EXTINGUISHING METHOD:
All extinguishing methods.
5.2 FIRST-AID METHOD
No particular method.
5.3 GENERAL TREATMENT MEASURES
In case of fires, hazardous combustion gases are formed.
6.0 ACCIDENTAL RELEASE MEASURES
6.1 ENVIRONMENTAL PROTECTING MEASURES
Dispose in accordance with local and state regulations. Waste should not be released to the
sewerage, ground water and surface water body.
7.0 HANDLING AND STORAGE
7.1 HANDLING
After cutting, the foam has knife-edge. Don’t discard the mylar on the floor in case slipping. When
transfer or use, please using safety equipment.
7.2 TRANSFORMATION OF PACKING MACHINERY
Convulve film is heavy and the matters need attention of film is similar to general heavy material.
It will generate static charge during usage the film, please use ionotron. Take precautionary
measures against static discharges.
7.3 STORAGE
Keep away from open flame, heat and sparks. Store in cool place. Need earthing device to reduce
endanger of static discharge. Provide corresponding quantity and species extinguishing device.
7.4 PERSONAL PRECAUTIONS
Respiratory protection: unnecessary in general.
Eye protection: use safety glasses.
Hand protection: protective gloves.
Others: protection footwear.
7.5 SANITARY CONDITIONS
Workshop is clean.
7.6 PROTECTION AGAINST FIRE AND EXPLOSION
In case of fires, use of a respiratory protection equipment and protective cloth.
In case of fires, hazardous combustion gases are formed.
Suitable extinguish media: sand, carbon dioxide and dry power.
Special exposure hazards arising from the substance itself, its combustion products: Hazardous
gases are emitted such as oxides of carbon.
7.7 DISPOSAL CONSIDERATIONS
Dispose in accordance with local and state regulations.
8.0 EXPOSURE CONTROLS/ PERSONAL PROTECTION
Imposes the limit of dust from relating administration
ACCGIH TLV：10mg/m3（Total dust）8H TWA
ACCGIH TLV：5mg/m3（pellet）8H TWA
9.0 PHYSICAL AND CHEMICAL PROPERTIES
9.1 Physical State: solid;
9.2 Density: 1.395-1.41g/cm3;
9.3 Appearance: transparent, white, black, yellow, red, blue and other color
9.4 Lower Igniting Point: 480℃;
9.5 Decomposition Temperature: ＞260℃;
9.6 Flash Point: 440℃.
10.0 STABILITY AND REACTIVITY
10.1 Explosivity: none;
10.2 Flammability: flammable when contact fire.
10.3 Pyrophorisity: none;
10.4 Oxidizability: none;
10.5 Stability: Stable under normal conditions.
11.0 TOXICOLOGICAL INFORMATION
The product does not have any harmful effect according to our experience and knowledge
12.0 ECOLOGICAL INFORMATION
The product has tiny effect to environment.
Ecological and toxicological information: None;
The product of biodegradation: The matter is insoluble in water and nonbiodegradable in a short
time.
13.0 DISPOSAL CONSIDERATIONS
The product is never degenerate under ground in long term.
The economic disposal method is incineration as well as in compliance with applicable local, state
and federal regulation.
14.0 TRANSPORT INFORMATION
No limit, but to notice the packing stability of heavy convulve film.
15.0 REGULSTION INFORMATION
The product is classified non-hazardous.
16.0 OTHER INFORMATION
This product may contain other polymer. In general, there is no hazard effect to human beings.
17.0 INSTRUCTION
Factor:
1. Temperature.
2. Pressure
3. Tension
4. Speed
5. Environment
Transfer temperature: The thermal transfer temperature is about 140 ℃ ~ 180 ℃, transfer do not
need glue, PVC panel about 50 ℃, transfer with glue.
Transfer the pressure: The thermal transfer pressure of version is about 25 ~ 30kg / c ㎡, and the
pressure must be uniform, too small, the film unable to adhesion to substrates; too big, the
substrate will be deformation, especially the hollow panel.
Transfer tension: The tension over too much will make the film overmuch stretched, the pattern
broken and unclear; but if the tension is too small, also make the surface uneven.
Transfer speed: It is according to the quality of material for transfer.
Transfer environment: No corrosive gas, speed ess than level 2, moderate 50 to 70 ° C, the
temperature about 20 ~ 30 ℃ is the best. The dust in the air as small as possible, because a lot of
plastic-like material with static electricity, will absorb the air dust, influence the quality of the
film's surface .
The PVC panel( hot transfer):
1. The transfer machine glue anilox mesh Usually in the 110 mesh, the pressure should be suitable,
according to the glue drying speed, if it is above 30 ℃, added 10 to 20% cyclohexanone in the
glue .
2. Transfer glue's quality is very important, and the standard content about 20%, add diluent
according to the using environment, if the glue drying too quickly or the content is not uniform
distribution, the transfer film will can not printing to the PVC panel, appears pitting or bubbles. If
the glue drying too slowly, the transfer film will shrink to the middle after cut down and the
pattern unclear.
3. the surface of Silicone roll should be smooth, no stab wounds and bump.
4. Check the finish product timely, the best molding time is 24 hours after transfer in a general
temperature.
HOT STAMPING FOIL storage:
1. Keep stand up , do not lie down, bump and pressure.
2. Keep away from heat, temperature should be -25 ℃ to 25 ℃, humidity less than 60%.
3. The film can storage last for one year
