Midmark VetPro® 1000

Veterinary Dental Cart

Model Numbers:
Service and
Parts Manual
8000-001
8000-002
8000-003
8000-004
8000-005
8000-006
8000-006S
8000-007
8000-007S Present Production Model Shown

8000-008
8000-008S FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY

SF-1928 Part No. 004-0586-00 Rev. AA8 (4/3/19)

 Access procedures

Section A General Information

Symbols...................................... iii

Section C
Upper Compartment................C-2
Ordering Parts........................... iii Middle Compartment...............C-3
Serial Number Location............ iii Lower Compartment................C-3

Table of Contents Specifications............................ iv

Model Description..................... iv
Scheduled Maintenance............. v
Water System...........................C-5
Delivery System.......................C-6

Wiring & Tubing diagrams

Section D
Wiring Diagram...................... D-2*
Tubing Diagrams................... D-7*
Troubleshooting Tri-Block Diagram................ D-12*
Compression Cycle.................A-2 Quad-Block Diagram.............D-13
Electrical ..................................A-3
Troubleshooting Chart............A-5

Testing & Adjustments

Section E
exploded views & parts lists
Checking for Air Leaks...........B-2 VetPro® 1000.............................E-2
Water Relay..............................B-3
Tri-block....................................B-4
Line Voltage.............................B-5
Compressor Head....................B-7
Capacitor..................................B-8
Check Valve & Solenoid........B-10
Pressure Switch.....................B-12
Section B

Air Regulator..........................B-14
Air Tank .................................B-16
Water System.........................B-17
Air Intake Filter......................B-18
Exhaust Muffler......................B-20
Foot Control...........................B-21
LED Light (Scaler).................B-22
Standard Scaler.....................B-23
Air/Oil Separator....................B-24
Fiber Optics (Early Units).....B-25
Fiber Optics (Current)...........B-26
Handpiece Holder Adjust......B-28
Foot Control...........................B-29 (*) Indicates multiple pages due to model / serial number break(s).

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] ii

 Symbols Ordering Parts

General Information
The following information is required when ordering parts:
warning • Serial number & model number
Indicates a potentially hazardous situation which
• Part number for desired part
could result in serious injury if not avoided.
(Refer to Section E: Exploded Views & Parts Lists)

Caution Non-warranty parts orders may be faxed to Midmark using

Indicates a potentially hazardous situation which may the Fax Order Form.
result in minor or moderate injury if not avoided. It may
also be used to alert against unsafe practices For warranty parts orders, call Midmark’s Technical Service
Department with the required information.
Equipment Alert Hours: 8:00 am to 5:00 p.m. EST (Monday thru Friday)
Indicates a potentially hazardous situation which could Phone: 1-800-Midmark
result in equipment damage if not avoided.

Serial Number Location

The symbols below may be used in this manual to represent
the operational status of table functions and components.

Indicates the function / component is working properly.

No action required.

Indicates the function / component is working,

but a problem exists.

Indicates the function is not working at all, or that the

component is faulty.
Serial Number
Label

Past Production Model Shown

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] iii

 Go To Table Of Contents

Specifications
Cart
Width 23 inches (58.42 cm)
Length 18 1/2 inches (46.99 cm)
Height 36 1/2 inches (92.71 cm)
Weight 130 lbs (58.97 kg)
Shipping Weight 150 lbs (68.04 kg)
Top of Cart Weight Restriction 25 lbs (11.33 kg)
Electrical (See Regulatory Compliance Chart - Next Page)
Fuse (Scaler Transformer) 800mA, 250 V, 3AG SLO BLO
Power Cord Length 10 ft. Hospital Grade
Handpiece
Connection Type Midwest 4-Hole Type Handpiece
Compressor
Motor Oil Free 1/3 HP

warning Working Pressure 70-100 PSI

Equipment not suitable Flow Rate 2.5 scfm @ 40 PSI
for use in the presence of Sound Level (full load) 40 dB
a flammable anesthetic mixture.
Air Tank 1 Gallon
Water Module
Reservoirs Two - 1 Liter - Toggled
Pressurized System 30-40 PSI
Handpiece Flush System Manual
Air and Water Connections External Quick Connects
Other
Duty Cycle Continuous Operation
Note: Exception, Units with LED
Scaler, 10 min. ON, 5 min. OFF
Classifications Class 1, Type B Applied Part,
Ordinary Equipment [IPXO]

warning
The Acteon Newtron® LED scaler complies with current electromagnetic compatibility standards. However, it
must not be used by or on those with cardiac stimulators or other active implants unless adequate electromag-
netic interference shielding is present. Check with a cardiologist to verify the EMI shielding capabilities of the implant. See
enclosed Newtron® LED manual for further advisories.

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 2/14/14] iv

 Go To Table Of Contents

Model Identification / Compliance Chart

Complies To: Electrical Ratings:

Model Description UL
CAN / CSA22.2, IEC 60601-1, VAC Cycles
60601-1, CE Amps
#601.1-M90 Ed. 2 +/- 10% (Hz)
Ed. 1
8000-001 VetPro 1000 w/ Scaler • • • • 115 6 60
8000-002 VetPro 1000 w/o Scaler • • • • 115 6 60
8000-003 VetPro 1000 w/ Scaler and Fiber
Optics • • • • 115 6 60

8000-004 VetPro 1000 w/o Scaler and w/

Fiber Optics • • • • 115 6 60

8000-005 VetPro 1000 w/ Scaler, Export • 230 3 50

8000-006 VetPro 1000 w/ LED Scaler and
Fiber Optics. Export • 230 3 50

8000-007 VetPro 1000 w/ LED Scaler and

2 Position Fiber Optics • • • • 115 6 60

8000-008 VetPro 1000 w/ LED Scaler and

Fiber Optics • • • • 115 6 60

8000-006S VetPro 1000 w/ LED Scaler and

Swivel Fiber Optics. Export • 230 3 50

8000-007S VetPro 1000 w/ LED Scaler and

2 Position Swivel Fiber Optics • • • • 115 6 60

8000-008S VetPro 1000 w/ LED Scaler and

Swivel Fiber Optics • • • • 115 6 60

Note
Refer to Section E For Serial Number Breaks

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/03/15] v

Scheduled Maintenance Chart

Scheduled Maintenance
Interval Inspection / Service Description

Daily Clean System Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.

Drain Air Regulator Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.

Drain Condensation from

Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.
Air Tank

Empty Water System Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.

After Each Procedure Clean Handpieces Follow manufacturer’s of handpieces recommendations.

Flush Handpieces Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.

Fill Water Bottles Refer to: Water Bottles in this manual.

Change Mufflers
Annually and Refer to: Mufflers and Air Regulator in this manual.
Air Regulator Filter
Date of Service: Model Number:

Location: Serial Number:

Service Technician: Notes:

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] vi

 Operation & Operation & Troubleshooting

Compression Cycle.............................A-2

Troubleshooting Electrical .............................................A-3*

Troubleshooting Chart.........................A-5

Section A

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] A-1

Compression Cycle & Air Flow
Atmospheric air is drawn in through the intake filter to the compressor head
where air is compressed and exhausted. Air travels though the check valve,
which prevents air flushing back into the head, then flows through the
solenoid. The solenoid allows air to escape for approximately two seconds
during start-up to relieve pressure from the head, then closes sending
pressurized air to the storage tank. Air from the storage tank activates the
pressure switch. As the storage tank fills the pressure switch opens at a
preset pressure and stops the compressor.

The air regulator adjusts air from the storage tank to 65 PSI. Storage tank air
also supplies the quick disconnect. Air going to the quick disconnect is not
regulated and pressure is at 100 PSI. Accessories connected to the quick
disconnect will need to have it’s own regulator installed if the manufacture
recommends less than 100 PSI.

The regulated air (65 PSI) flows to the foot control and water bottles. When
user activates the throttle valve by depressing the foot control, air is sent
through the tri-block and each instrument manifold. When the instrument
is removed from the holder the holder valve is activated allowing air to flow
through the handpiece. There are drive air adjustment valves to adjust air
pressure for the instruments.

The air/water syringe is activated by pressing on the instrument’s air and

water buttons. The user can make drive air, coolant air and water flow
adjustments. Air flows though the gauge to show pressure readings.
Regulated air also pressurizes the water bottles. Air to the water bottles
is adjusted to 40 PSI by the water pressure regulator and can be
lowered by adjusting the water pressure regulator.

Water Flow
VetPro® 1000 has a self-contained water system with two, one-liter
bottles. The toggle switch opens and closes the use of the bottles. When
the toggle switch is set in the middle, both valves to the bottles are closed
depressurizing the bottles and stopping flow. When toggle switch is flipped
toward a bottle that bottles valve opens and allows water flow to each needle
valve’s instrument. The needle valve is the users way to control water flow to
instruments.
VA1245

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 03/20/12] A-2 Always verify model & serial number
Electrical Flow
• Supply line voltage is always present
at the Dental Cart power cord receptacle
when plugged into a wall receptacle.
When the On/Off switch is turned on, line
voltage, 115 VAC, is supplied to the
Terminal Block and Pressure Switch.

• 115 VAC comes from the Terminal Block

and energizes the Accessory Receptacles,
Timer, Motor, Fan and Transformer.

•The Timer keeps the solenoid turned

off until the compressor is running at full
RPM. The Solenoid is normally opened
when not energized. The Solenoid allows
air to escape for approximately two
seconds to relieve pressure from the
head, then closes sending pressurized
air to the storage tank.

• The system will continue to run until

the pressure inside the system reaches
100 PSI (+ / - 5 PSI) (Cut-out time)
It will turn back on at 65 PSI (+ / - 5 PSI)
(Cut-In time).

• When the Pressure Switch is at

65 PSI (+ / - 5 PSI) or below it’s
contacts are closed and the compressor
is energized.

• Transformer supplies 24 VAC to Scaler

(if applicable).

Models: All All

Serial Numbers: TGC001000Thru TGC001254 V796868 thru V933242

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 8/9/10] A-3 Always verify model & serial number
Electrical Flow - Current Units
• Supply line voltage is always present at the
Dental Cart power cord receptacle when plugged
into a wall receptacle. When the On/Off switch is
turned on, line voltage, 115 VAC, is supplied to
the Terminal Block and Pressure Switch.

• 115 VAC comes from the Terminal Block and

energizes the Timer, Motor, Fan and Transformer.

•The Timer keeps the solenoid turned off until the

compressor is running at full RPM. The Solenoid
is normally opened when not energized. The
Solenoid allows air to escape for approximately
two seconds to relieve pressure from the head,
then closes sending pressurized air to the stor-
age tank.

• The system will continue to run until the

pressure inside the system reaches
100 PSI (+ / - 5 PSI) (Cut-out time)
It will turn back on at 65 PSI (+ / - 5 PSI)
(Cut-In time).

• When the Pressure Switch is at

65 PSI (+ / - 5 PSI) or below it’s contacts are
closed and the compressor is energized.

• Transformer supplies 24 VAC to Scaler

(if applicable).

Models: Please refer to Section D

Serial Numbers: for Wire Diagrams Listed Under Serial Numbers

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: ] A-4 Always verify model & serial number
Troubleshooting Chart
Problem Probable Cause Check Correction
Syringe has no Empty water bottles. Water level in bottles. Fill water bottles.
water when button
Toggle not seated to Check toggle location. Push toggle completely to left or right side.
depressed.
right or left side.
Water Regulator Check Water regulator. Verify bottles are pressurized. Regulator should be adjusted all the way
to the right.
Quick disconnect. Check water (blue) Depress quick disconnect with a screwdriver and hold for serveral
disconnect. seconds. Hold rag underneath screwdriver for any water flow. If no water
flow, change syringe check valve.
Tubing Crimped. Check for crimped tubing. Replace tubing.
Syringe. Check Syringe tip and Change syringe tip. Check syringe cartridge for water, repair or replace.
cartridge.
Handpiece has no Needle Valves closed. Check needle valves. Verify needle valves are open.
water flow but
Handpieces. Remove handpieces and verify you have water If you have water coming from syringe, remove handpieces and recheck
syringe is still working.
through tubing. water flow from tubing, if none repair or replace handpieces.
Kinked Tubing. Check for kinked tubing from foot control to water Replace tubing.
relay.

Water Relay Remove air tubing from foot control going to water If air is present, repair water relay membrane or replace water relay.
relay, depress foot control and check for air. Refer to: Section B Water Relay.
Remove water tubing from tri-block coming from If water is present, repair or replace tri-block. If no water is present,
water relay, depress foot control. repair or replace water relay. Refer to: Section B Tri-Block or Water
Relay.
Handpiece leaking in Incorrect holder Check location of handpiece. Place handpiece in correct holder position.
holder. location.
Membrane If foot control is not depressed while handpieces Change membrane (diaphragm) in block.
(Diaphragm) are hanging in holders, membrane in (tri or dual) Refer to Section B Tri-Block.
block is leaking.
Water bottle or toggle Check valve. Check, check valve. Toggle over to one side and fill water bottle. Observe other side for leak-
leaking. ing. If it is leaking , replace check valve. Repeat for other side.
Handpiece in holder Handpiece in wrong Verify handpiece is in correct holder position. Move handpiece to correct position.
and is still running holder.
when another hand- Holder switch out of Check set screw adjustment. Adjust set screw on holder. Refer to Section B: Handpiece Holder
piece is in use. adjustment. Adjustment.
Tri-block. Check air to tri-block supply. Pinch tubing off with pliers, handpiece should stop, if not check pilot
valve.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/21/13] A-5 Always verify model & serial number
Troubleshooting Chart
Problem Probable Cause Check Correction
Compressor will not start. Power cord unplugged. Verify power cord is plugged in cart and outlet. Plug power cord into cart and/or outlet.
On/Off switch is off. Check that the on/off switch is turned on. Turn on/off switch on.
Circuit breaker tripped. Check to see if circuit breaker needs reset. Reset circuit breaker.
No power at outlet. Check for voltage at outlet and/or move to Reset circuit breaker. Assure outlet is on dedicated circuit
another room. capable of handling cart requirements.
Loose wire connection. Check back panel wire connections. Reconnect wires to back panel if loose.
Check voltage on circuit breaker, power cord bracket and
on/off switch. Refer to: Section B Line Voltage
Capacitor. Check Capacitor. Test capacitor. Replace if needed.
Refer to Section B: Capacitor
Pressure Switch Frozen Check Pressure Switch. Replace Pressure Switch. Refer to: Section B Pressure
Switch.
Motor/Compressor Frozen Unplug cart. Can you manually move If you are unable to move compressor fans, replace com-
compressor fans? pressor. Refer to: Section B Compressor
Compressor will not shut off or will Air leaks in system and/or Check for air leaks. Refer to: Section B Checking for Air Leaks
recycle often. foot control.
Compressor will not recycle or Room temperature too high. Ambient room temperature. Move to another room. Try running unit.
stalls and or breaker tripping
Check Valve. See if check valve is sticking. Spray soapy water on solenoid muffler, if it bubbles while
causing air to deplete.
compressor is running, replace check valve.
Refer to: Section B Check Valve
Solenoid. Check Solenoid. Turn off unit and drain air tank. Turn on unit and see if
solenoid bubbles for a few seconds, if not replace sole-
noid.
Refer to: Section B Solenoid
Compressor makes humming noise To much back pressure. See if check valve is sticking. Spray soapy water on solenoid muffler, if it bubbles while
and or smells like it is burning. compressor is running, replace check valve.
Refer to: Section B Check Valve
LED light not working on scaler. LED light not installed Check polarity. Check polarity ( + & - ) connection of LED bulb.
(Models 8000-007, 8000-007S, 8000- properly. Refer to: Section B LED Scaler
008 & 8000-008S ONLY) Tubing connection bad. Check tubing connection. Check continuity between tubing connection and scaler
plug. Refer to: Section B LED Scaler
Poor contact with pins. Clean pins. Clean pins with alcohol and allow to dry before use.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: [11/03/15] A-6 Always verify model & serial number
Troubleshooting Chart
Problem Probable Cause Check Correction
Scaler running intermittently or low Poor power supply Check power supply. Verify VetPro 1000 is plugged into wall and not loose.
power, or not vibrating for no connection.
apparent reason. Air pressure not set Check air pressure. Check air pressure. Refer to: Section B Air Regulator
correctly.
Not drive air. Check drive air adjustment knob. Verify Drive air adjustment knob is all the way open.
Tubing. Check tubing continuity. Check continunity in black and orange wires of the tubing.
Refer to: Section B Scaler Tubing
Check HI resistance. Check HI resistance between the black and orange tubing
wires. Refer to: Section B Scaler Tubing
Tip not tight enough. Check tip. Verify tip is tightened. Tip must be tightened for scaler
operation to work.
Tip is worn. Check tip. Tip must be within tolerance as per tip chart for scaler
operation to work. Change tip.
Potentiometer Harness bad Check for proper setting. Service tip: if setting If you have 24 V AC or 31 V DC, Check potentiometer for
or misadjusted. is correct move on to Ώ check. proper resistance sweep of 4 to 4.7K Ώ when turned from
Min to Max on Ohmmeter measuring between the white
and brown/blue wires on molex.

If resistance is not ok, replace potentiometer harness. If

resistance is ok, check all wiring and pins for continuity.
Repair any wiring that does not pass continuity check.

If you do not have 24V AC or 31 V DC Check power sup-

ply and air/electric switch for failure.

Replace potentiometer harness if power supply or air-

electric switch has failed.
Tubing is damaged. Check tubing. Check continuity in black and orange wires of the tubing.
Refer to: Section B Scaler Tubing
Handpiece is damaged. Swap out handpieces. If scaler operates properly with different handpiece, old
one is damaged.
Transducer in scaler. Check transducer in scaler. Replace with a known working handpiece. If the replace-
ment handpiece works, then the transducer is bad in
the problem handpiece. Return handpiece to Acteon for
service or replace with new handpiece.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/21/13] A-7 Always verify model & serial number
 Testing & Repair Component / System

Checking for Air Leaks........................B-2

Water Relay.........................................B-3
Tri-block...............................................B-4

Section B Line Voltage........................................B-5

Compressor Head...............................B-7
Capacitor.............................................B-8
Check Valve & Solenoid......................B-10
Pressure Switch..................................B-12
Air Regulator.......................................B-14
Air Tank ..............................................B-16
Water System......................................B-17
Air Intake Filter....................................B-18
Exhaust Muffler...................................B-20
Foot Control........................................B-21
LED Light............................................B-22
Standard Scaler..................................B-23
Air/Oil Separator..................................B-24
Fiber Optic (Early units).....................B-25
Fiber Optic (Current units)...................B-26
Handpiece Holder Adjustment.............B-28
Foot Control........................................

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-1

Testing & Repair

Checking for Leaks

Refer to: Page
Use Soapy Water to check for leaks... Access Procedures.............................C-1
A) Listen to foot control for air leaks.
B) Tubing inside back of cart.
C) Air regulator and “T” fittings.
D) Storage air tank and tank fittings.
E) Tri-block and instrument manifolds.
F) Air and water quick disconnects.
G) Handpiece docks.
H) Water bottles. Quick Disconnects
I) Solenoid muffler, check valve and compressor fittings.
Note: Refer to: Section C for Access Procedures

Foot
Control

Air Tank & Fittings

Regulator & Fittings
Tubing

Tri-Block
& Manifolds

Handpiece
Docks
VA1252
Solenoid & Check Valve
Compressor Fittings

Water Bottles
Earlier Production Model Shown

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/21/13] B-2 Always verify model & serial number
Testing & Repair

Water Relay - Function and Location

Refer to: Page
Access Procedures.............................C-1
The water relay is located inside the delivery panel. Tubing Diagram...................................D-1
Exploded Views & Parts List...............E-1
The water relay stops the water flow to the needle valves until the foot control (throttle valve) is pressed,
then air flows to the water relay and opens the needle valves allowing water to flow to the instruments. It
also supplies water directly to the syringe.

Earlier Production Model Shown

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-3 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures.............................C-1
Step 1: Disconnect power. Tubing Diagram...................................D-1
Water Relay - Testing Remove delivery panel. Exploded Views & Parts List...............E-1

Note: Refer to Section C Access Procedures

Step 2: Disconnect orange tubing from water relay .

Depress foot control.

Foot Control
Tube

Incoming
Water
Supply

Tri-block
Manifold
Tube

Syringe
Tube Results Status Required Action

No water when foot control not

Water flow good.
depressed.
Water when foot control is
Water flow good.
depressed.
Step 3: Disconnect tubing from water relay manifold. No air flow when orange tube is Tubing clogged or damaged. Change
Depress foot control. disconnected. orange tubing.
No water flow when manifold Water relay is bad. Replace water
tubing is disconnected. relay.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/21/13] B-4 Always verify model & serial number
Testing & Repair

Tri-Block (Dual Block in Models without Scaler 8000-002 & -004)

Refer to: Page
Access Procedures.............................C-1
Function and Location Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
The tri-block is located behind the delivery instruments.

It is a manifold that the air and water source travel through and is routed to dif-
ferent components in the delivery system. When the foot control is activated, air
flows into the tri-block through two tubes, one for coolant air and one for drive air.
Coolant air flows from the tri-block to each instrument manifold. Drive air flows
though the adjustment valve on the tri-block to each instrument. The tri-block also
supplies air to the air pressure gauge.

Water flows from the water relay valve through the tri-block and to each water
needle valve. The tri-block has a membrane seal that provides a fluid-tight seal
between the two walls. To access the membrane for repair, remove allen screws
from the front of the block to separate the block. Also Refer to: Section C Access
Procedures to access the block and to Section D for a tubing diagram of the
tri-block. Replacement kit for the membrane is available.

Note: The air/water supply for the syringe does not flow through the tri-block.

Membrane

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-5 Always verify model & serial number
Testing & Repair

Line Voltage Testing - 115 VAC

Refer to: Page
Pressure Switch..................................B-12
Components to check line voltage are listed in the chart below. Access Procedures.............................C-1
Tubing Diagrams.................................D-1
115 VAC Models Only Reference Serial Numbers Below Exploded Views & Parts List...............E-1
Meter Reading Status Required Action

Caution
< 115 VAC On / Off Switch Replace On / Off Switch When testing components with power
on use care to prevent electrical shock.
< 115 VAC Pressure Switch Replace Pressure Switch

< 115 VAC Terminal Block Replace Terminal Block

To check line voltage...
< 115 VAC Fiber Optic Set multi-meter to v
Replace Receptacle
Receptacles Use multi-meter to verify voltage.
< 115 VAC Timer Replace Timer

< 115 VAC Fan Replace Fan

< 115 VAC Transformer Replace Transformer

115 VAC = On / Off Switch On / Off Switch OK

115 VAC = Pressure Switch Pressure Switch OK

115 VAC = Terminal Block Terminal Block OK

115 VAC = Fiber Optic

Accessory Receptacles OK
Receptacles

115 VAC = Timer Timer OK

115 VAC = Fan Fan OK

115 VAC = Transformer Transformer OK

Models: All All

Serial Numbers: TGC001000Thru TGC001254 V796868 thru V933242

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 8/9/10] B-6 Always verify model & serial number
Testing & Repair

Line Voltage Testing - 230 VAC Refer to: Page

Pressure Switch..................................B-11
Access Procedures.............................C-1
Components to check line voltage are listed in the chart below. Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1

Caution
When testing components with power
on use care to prevent electrical shock.

230 VAC Models Only To check line voltage...

Set multi-meter to v
Reference Serial Numbers Below Use multi-meter to verify voltage.

Meter Reading Status Required Action

< 230 VAC On / Off Switch Replace On / Off Switch
< 230 VAC Pressure Switch Replace Pressure Switch
< 230 VAC Terminal Block Replace Terminal Block
< 230 VAC Timer Replace Timer
< 230 VAC Fan Replace Fan
< 230 VAC Transformer Replace Transformer
< 230 VAC Fiber Optic Receptacle Replace Receptacle
230 = VAC On / Off Switch On / Off Switch OK
230 = VAC Pressure Switch Pressure Switch OK
230 = VAC Terminal Block Terminal Block OK
230 = VAC Timer Timer OK
230 = VAC Fan Fan OK
230 = VAC Transformer Transformer OK
231 = VAC Fiber Optic Receptacle Fiber Optic Receptacle OK

Models: All
Serial Numbers: V933243 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 8/9/10] B-7 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Compressor Head - Function and Location Exploded Views & Parts List...............E-1
Compressor Rebuild .......642648A_0605
The Compressor Head is located in the lower compartment.

Atmospheric air is drawn in though the intake filter to the compressor head where air is compressed
and exhausted to the storage tank. Heat is generated from the compression process. The compressor
head has a fan on both ends. There is also a fan located above the compressor head to pull hot air up
and out though a vent on the back middle compartment of the cart. If you are unable to manually move
the fans on the compressor (when power supply is completely shut-down), the compressor head needs
replaced. There is a head rebuild kit available.

Compressor Head

Earlier Production Model Shown

Intake Filter
Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 09/24/08] B-8 Always verify model & serial number
Testing & Repair
Refer to: Page
Test Capacitor.....................................B-9
Access Procedures.............................C-1
Capacitor - Function and Location Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
The capacitor is located in the lower compartment.

The run capacitor aids in running efficiency. It creates

a phase shift to give more power to the compressor.

Capacitor

Earlier Production Model Shown

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-9 Always verify model & serial number
Testing & Repair

Capacitor - Testing Step 4: Place meter probes on capacitor connectors.

Reverse the leads, this should produce the same reading.

Step 1: Disconnect power.

Access run capacitor in lower compartment.
Note: Refer to: Section C - Lower Compartment.

Step 2: Discharge capacitor by touching screwdrivers

to both contacts on the capacitor and to each other.

Step 3: Set meter to Ω reading.

Meter Reading Status Required Action

“O” or “Open” Reading Replace Capacitor

Start Low and Increases Capacitor

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-10 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Check Valve & Solenoid - Function and Location Exploded Views & Parts List...............E-1

The check valve and solenoid are located in the lower compartment.

Compressed air travels from the compressor head though the check valve,
which prevents air flushing back into the head. Then air flows though the
solenoid. The solenoid allows air to escape for approximately two seconds
to relieve pressure from the head then closes sending pressurized air to the
storage tank.
Earlier Production Model Shown

Solenoid

Check Valve
Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-11 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Check Valve - Clean Exploded Views & Parts List...............E-1

Step 1: Disconnect power.

Step 2: Remove check valve from compressor head and solenoid.

Step 3: Blow out valve with air.

If valve is sticking, replace.

VA1261

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-12 Always verify model & serial number
Testing & Repair
Refer to: Page
Pressure Switch Adjustment...............B-13
Access Procedures.............................C-1
Pressure Switch- Function and Location Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
The pressure switch is located in the middle compartment accessed from
the back of the cart. When the storage tank is filled to the preset pressure
the pressure switch will open and stop the compressor.

Cut-In / Cut-Out time is the minimum and maximum discharge pressures at

which the compressor will switch from unload to load operation (cut-in) or
from load to unload (cut-out). The pressure switch controls the Cut-In and
Cut-Out times.

Pressure Switch

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-13 Always verify model & serial number
Testing & Repair

Pressure Switch - Adjustment

Step 1: Run compressor until pressure reaches 100 PSI. Step 2: If compressor didn’t shut down at 100 PSI,
access pressure switch and remove cover.
Note: Compressor should shut off close to 100 lbs.
Note: Refer to: Section C Middle Compartment

Adjustment Screw “A” Adjustment Screw “B”

Step 3: Make adjustment.

• Adjustment screw “A” , turn clockwise to increase both Cut-In and Cut-Out pressure.
• Differential pressure adjustment screw “B”, turn Clockwise to increase Cut-In pressure without affecting Cut-Out.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-14 Always verify model & serial number
Testing & Repair
Refer to: Page
Air Regulator Adjustment....................B-15
Air Regulator Maintenance..................B-16
Air Regulator - Function and Location Access Procedures.............................C-1
Tubing Diagrams.................................D-1
The regulator is located in the upper compartment behind the rear door. Exploded Views & Parts List...............E-1

The air regulator regulates air from the storage tank from 100 PSI to 65 PSI. The regulator
should only be set for 65 PSI. There is a button on the bottom of the regulator that will drain
condensation by pressing on it at the end of each work day.

Air Regulator

Earlier Production Model Shown

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-15 Always verify model & serial number
Testing & Repair
Refer to: Page
Air Regulator Maintenance..................B-16
Access Procedures.............................C-1
Air Regulator- Adjustment Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1

Equipment alert
Do not adjust regulator over 65
PSI, it will overheat the compressor. Air
pressure for the piezo electric scaler should Decrease Increase
be set to 60 PSI.

To Adjust Regulator... Adjustment

A) Pull adjustment knob upward to unlock. Knob
B) Rotate adjustment knob clockwise to Unlock
increase pressure, counterclockwise to
decrease pressure. Lock
C) Push adjustment knob downward to lock.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-16 Always verify model & serial number
Testing & Repair
Refer to: Page
Air Regulator Adjustment....................B-15
Access Procedures.............................C-1
Air Regulator & Air Tank - Maintenance Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1

To Drain Air Regulator...

Place a cloth under the regulator and depress Present Model Shown with Yellow Tubing
the button until there is no water coming out. Earlier Models have Red Tubing

Note
User should drain regulator and air tank daily.
Button

Valve
Opened

To Drain Condensation from Air Tank...

A) Turn power switch off.
VA1238

B) Position end of yellow tube so it drains into a container.

C) Turn drain valve slowly to open.
D) When no water is coming out, slowly close valve.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 6/16/10] B-17 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Water System - Function and Location Exploded Views & Parts List...............E-1

The self-contained water system has two, one-liter bottles located on the front panel
under the instruments. It is recommended to use only distilled water in the bottles. The
water bottles supply water to the instruments that use water and to the quick disconnect
on the back of the cart. Air flows through the water regulator to pressurize the water
bottles. The water regulator is located between the water bottles and is set at 40 PSI.
Use the water needle valve to adjust water flow for each instrument.

There is a toggle valve between the water bottles, which controls which water bottle
will supply water. When the toggle is in the center neither water bottles is pressurized.
Move the toggle toward the left to pressurize the left bottle and depressurize the right
bottle. Toggle to the right to pressurize the right bottle and depressurize the left bottle.

Water Regulator

Toggle

Water Bottles

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 03/20/12] B-18 Always verify model & serial number
Testing & Repair
Refer to: Page
Clean Air Intake Filter..........................B-19
Access Procedures.............................C-1
Air Intake Filter - Function and Location Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Atmospheric air is drawn in though the intake filter before
flowing to the compressor head. The intake filter protects the
head from dust and debris and should be changed annually.

Earlier Production Model Shown

Air Intake Filter

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-19 Always verify model & serial number
Testing & Repair
Refer to: Page
Air Intake Filter - Function & Location.B-18
Access Procedures.............................C-1
Air Intake Filter - Clean Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1

Step 1: Remove filter housing from cap by pushing in and turning.

Filter

Housing

Step 2: Remove filter and clean by blowing out or replace as needed.

Install new filter in housing to cap on compressor head.
Install cover on lower compartment.
Note: Air Intake Filter should be changed annually.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-20 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exhaust Muffler Exploded Views & Parts List...............E-1

The exhaust muffler provides lower sound (dba) levels for the
VetPro® 1000. The exhaust muffler can be cleaned using a rag and
should be replaced annually.

Exhaust Muffler

Earlier Production Model Shown

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-21 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Foot Control- Function and Location Exploded Views & Parts List...............E-1
Foot Control Replacement........003-1899-00
The foot control opens a throttle valve that allows air flow to the instrument manifolds.
The syringe is not controlled by the foot control. It is operated by the hand controls on
the syringe itself.

There is a foot control storage bracket on the back of the unit to hang the cord on when
the cart is not in use or when moving the cart to a new location.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 08/06/08] B-22 Always verify model & serial number
Testing & Repair

LED Scaler To check polarity..

Verify + on the LED ring and the handpiece are the same side.
Check and Test
LED (-)
LED (+)

To test continuity...
Set meter to Ω and check connections.
PIN 1 is wired to Black wire of Molex Plug. (Ultrasound Signal)
PIN 2 is wired to White wire of Molex Plug. (LED Power)
PIN 3 is wired to Blue wire of Molex Plug. (LED Power)
PIN 4 is wired to Orange wire of Molex Plug. (Ultrasound Signal)

Meter Reading Status Required Action

“O” or “Open” Reading

Replace Scaler Cord
(Continunity Check)
0.1 - 1.0 Ohms
Scaler Cord OK
(Continunity Check) To test in the tubing connection...
---
Voltage within specs when Set meter to V. With no LED in socket, voltage reading will
measured at LED Ring Handpiece, tubing and module OK be approximately 21 VDC. With LED inserted, voltage
(Test Tubing Connections) reading will be approximately 12 or 14 VDC measured at
Voltage out of specs at pins on the blue and white wire on molex plug.
Tubing pin Voltage ok - Replace Handpiece
LED Ring Pins
Molex Plug Voltage ok and NOT at Tubing Pins - Replace Tubing Note: This requires thin probes to make contact.
(Test Tubing Connections)

Models: 8000-007, -008

Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-23 Always verify model & serial number
Testing & Repair
Refer to: Page
To test continuity... Access Procedures.............................C-1
Scaler Tubing Set meter to Ω. Tubing Diagrams.................................D-1
Check orange wire of molex to the center pin of tubing. Exploded Views & Parts List...............E-1
Testing Check right side (as shown) pin of tubing to the black wire in molex.
Note: Refer to: Section D Wire Diagrams

Check To Orange
Wire

Check To
Black Wire

Note
Only check for HI resistance
if scaler is experiencing
intermittent or low power.

To check HI resistance...
• Set ohmmeter for 20 MEG OHM scale. If using a manual setting meter or just “OHMS” if auto ranging meter.
• Disconnect handpiece from tubing.
• Disconnect molex from module.
• Without touching probe leads with fingers, place the meter leads across the orange and black wires in molex. There
should be (Open Circuit). Any reading other than this indicates a HI Resistance short in tubing and needs to be replaced.

Meter Reading Status Required Action

0.1 - 1.0 Ohms

Tubing OK
(Continunity Check)
Models: 8000-001, 003, -005, -006 “O” or “Open”
Reading (Continunity Change Tubing
Serial Numbers: all Check)

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 6/7/12] B-24 Always verify model & serial number
Testing and Repair

Air / Oil Separator- Cleaning

The air/oil separator (exhaust collector) acts as an exhaust muffler and oil collector Note
(gauze). When gauze becomes saturated it must be replaced. User should check air/oil separator periodically.

To clean the air/oil separator...

A) Turn master ON/Off switch Off.
B) Remove air/oil separator container.
C) Dispose of the fluid and saturated gauze.
D) Disinfect container and mounting cap.
E) Install clean gauze and reinstall the container.

VA1676i

Models: All
Serial Numbers: V1043398 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-25 Always verify model & serial number
Testing & Repair
To check voltage... Refer to: Page
A) Verify voltage at power supply connection to optic controller (stablizer) is 3-4 VAC. Access Procedures........C-1
Fiber Optic B) With foot pedal depressed, wire connections at optic controller (stablizer). Tubing Diagrams............D-1
(Earlier Production C) Verify voltage is 2.9 - 4.1 VAC. Exploded Views ............E-1
D) Remove instrument from tubing, remove bulb (pry out) from tubing.
Verify SN )
E) Check voltage at bulb wire connectors on tubing end. Verify voltage is 2.9 - 4.1 VAC.

Testing

Optic
Note
If the voltage is out of spec at the Optic Controller (Stablizer), check the air tubing
Controller
for air flow. If no air flow, check for a kink in the line. Repair and restore air flow, then
(Stablizer)
recheck voltage again. If voltage is still out of spec, then replace the optic controller.

Voltage Checks Shown

End of Tubing
Volltage Check
Power
Supply Check

Power
Supply

Meter Reading Status Required Action

Voltage Within Specs at All three Checks Wiring in Tubing, Power Supply OK, replace Bulb

Voltage out of spec at Power Source Replace Power Supply

Voltage out of spec at Optic Controller (Stablizer) Replace Optic Controller (Stablizer)
Voltage out of spec at tubing end. Replace Tubing.

Models: All All

Serial Numbers: TGC001000 thru TGC001024 V796868 thru V933242

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] B-26 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures........C-1
Fiber Optic Tubing Diagrams............D-1
(Current Production - Verify SN ) Exploded Views ............E-1

Testing To check voltage...

A) Verify voltage at power supply connection to optic controller (stablizer) is 9 VDC.
B) With foot pedal depressed, check voltage on black and white wire connections at
optic controller (stablizer). Verify voltage is 2.9 - 4.1 VDC.
C) Remove instrument, swivel coupler (if equipped) and bulb (light module) from tubing.
D) Check voltage at wire connectors on tubing end. Verify voltage is 2.9 - 4.1 VDC.

End of Tubing
Volltage Check
Power Supply Optic
Check Controller
(Stablizer) Voltage Checks Shown

Note
Power If the voltage is out of spec at the Optic Controller (Stablizer), check the air tubing
Supply Depress Foot
for air flow. If no air flow, check for a kink in the line. Repair and restore air flow, then
Control to
recheck voltage again. If voltage is still out of spec, then replace the optic controller.
Check Wire Connection
Voltage
Meter Reading Status Required Action

Voltage Within Specs at All three Checks Wiring in Tubing, Power Supply OK, replace Bulb

Voltage out of spec at Power Source Replace Power Supply

Voltage out of spec at Optic Controller (Stablizer) Replace Optic Controller (Stablizer)
Voltage out of spec at tubing end. Replace Tubing.

Models: Only 8000-003, -004, -006, -006S,-007,-007S -008, -008S

Serial Numbers: V933243 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/03/15 B-27 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures........C-1
Handpiece Holder Adjustment Tubing Diagrams............D-1
Exploded Views ............E-1

Earlier Production Current Production

1/16” Allen
Wrench

Tubing Connector

1/16” Allen Wrench

To adjust handpiece holders..

A) Turn set screw on holder.
B) Place handpiece back in holder.
C) Verify handpiece shuts off. If not, adjust set screw again.
Note: If you loosen the earlier production style to far, the tubing connector will come out of holder. Put tubing connector back into slot and tighten set screw.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 9/10/12] B-28 Always verify model & serial number
Testing & Repair
Refer to: Page
Access Procedures........C-1
Checking Foot Control Tubing Diagrams............D-1
Exploded Views ............E-1

To check a foot controller that is leaking..

A) Check for hole or puncture in tubing.
B) Check springs, if compressed, stretch them out and reinstall.
C) Use soapy water to check o-rings for leaks.
D) Check tri-block diaphragm to see if it has a puncture. Tri-block
is located behind the delivery panel, refer to Section C for access
instructions.
Note: Also refer to: Checking for Leaks in Section B

Remove for Spring Access

Remove for O-ring

Models: All Access
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/21/13] B-29 Always verify model & serial number
 Access Upper Compartment............................C-2

Procedures
Middle Compartment...........................C-3

Section C Lower Compartment............................C-3

Water System......................................C-5
Delivery System..................................C-6

Earlier Production Model Shown

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 9/11/09] C-1

Access Procedures

Upper Compartment

Caution
Power must be turned off when opening back door.

Step 1: Open door on back of cart to access upper compartment components.

Back Door

Models: All Earlier Production Model Shown

Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 09/11/09] C-2 Always verify model & serial number
Access Procedures

Middle Compartment

Caution
Power must be turned off when removing panel.

Step 1: Unplug power cord from wall outlet and cart.

Step 2: Remove four screws to remove panel to access middle compartment.

VA1281
Earlier Production Models Only
Have a Middle Panel

Models: All
Serial Numbers: TGC001000 thru TGC001244

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 09/11/09] C-3 Always verify model & serial number
Access Procedures
Caution
Power must be turned off when removing panel.
Lower Compartment

Step 1: Remove six screws to remove panel to access lower compartment.

Current Models do not

have Receptacle

Earlier Production Models

Earlier Production Model Shown

VA1282

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 9/17/09] C-4 Always verify model & serial number
Access Procedures

Water System

Step 1: Remove screws from top of water bottle bracket.

VA1283
Step 2: Remove water bottle from bracket.

Earlier Production Model Shown

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/22/13] C-5 Always verify model & serial number
Access Procedures

Delivery Panel Access

Caution
Power must be turned off when removing panel.
Step 1: Remove two screws from top of panel.
Current Production Models
Earlier Production Models

VA1284

Step 2: Remove two screws from instrument holder panel.

Note: Push in on the foot control tubing to be able to pull out on the tubing
connected to back of the delivery panel.

Models: All
Serial Numbers: all

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/21/13] C-6 Always verify model & serial number
 Wiring & Tubing
Component/System Page
Wiring Diagrams..................................D-2*
Tubing Diagrams.................................D-7*
Tri-Block..............................................D-12*

Section D Diagrams
Quad-Block.........................................D-13

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] D-1

VetPro® 1000 Wire Diagram
Fiber Optics Detailed

VetPro® 1000
115 VAC
Satelec Scaler (Optional)
Components Power Supply

Scaler
Control VA1690
Box

Receptacle for
WHT
B
Fiber Optics Fiber Optic System
Components
BLK
(Optional)

GRN Adjustment
Knob
GRN

Transformer
C BLK
BLK
GRN BLK K Air
Switch

Fan G
L J
F
BLK

Pressure
Switch
BRN
BLK BLK BLK
BRN
BLK
WHT On/Off
WHT
Power Switch
WHT Accessory
GRN Receptacle WHT
BLK
GRN
GRN
Circuit
Breaker
BLK
Terminal Block BLK
BLK

GRN H
GRD

WHT

A
BRN
WHT 115 VAC Wiring Diagram
Power Cord
BRN
Item Description Part Number
M
GRN
Receptacle
Compressor Head
Jumper Wire (Green-Yellow)
E J A 2 1/2” 015-0737-32
D B Jumper Wire (White) 23” 015-0737-34
Timer Solenoid C Interior Receptacle 015-2555-00
GRN GRN
GRD I D Compressor Harness 015-2556-00
Exterior Receptacle
Capacitor E 015-2557-00
BRN
BLU BLK
Connecting Harness
Exterior Receptacle
F 015-2558-00
BLK
Harness
G Jumper Wire (Black) 9” 015-0741-12
Assembled at Factory
H Jumper Wire (Black) 3 3/4” 015-0741-13
I Jumper Wire (Black) 4” 015-0741-14
J Jumper Wire (White) 5 1/4” 015-0741-15
Models: All All K Jumper Wire (Black) 015-0737-33
Serial Numbers: TGC001000Thru TGC001254 V796868 thru V933242 L Fan Cord 015-2581-00
M Jumper 015-0022-01

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 9/22/11] D-2 Always verify model & serial number
VetPro® 1000 Wire Diagram - 2
VetPro 1000™
115 VAC Fiber Optics Detailed -007
Model Only
Satelec Scaler (Optional)
Fiber Optics
Components
Components
Power Supply
(Optional)

Control Scaler
Box

I
BLK

Receptacle for
Fiber Optic System
Adjustment
Knob

B Transformer
WHT
H VA1691

BLK
BLK
Fuse
BLK BLK J Air
Switch
BK

A
WH T0.8AL,250V,3AG
GRN/YEL

M
BK

S
WHT

GND
Fan GRN/YEL

BLU Pressure GRN/YEL

L
Back Panel
G
Switch

BRN
F E On/Off
BRN
BRN
Q Power Switch
Wiring Diagram
BLK WHT
BLK
WHT
Item Description Part
BLK BLK O WHT Circuit
Breakers N
Number
Terminal
Block A Transformer Input (White) 015-2713-00
P
BL
WHT WHT
015-2712-00
WHT B Transformer Input (Black)
BLK BLK
BRN C Power Harness 015-2690-00

K C 115 VAC
Power Cord
D Compressor Harness 015-2689-00
Compressor Head Receptacle
E Fan Cord 015-2581-00
R F Jumper Wire (Black) 9” 015-0741-12
Timer
G Jumper Wire (Black) 2 1/2” 015-0737-44
Solenoid
BRN H Jumper Wire (Black) 6” 015-0737-43
Note: Solenoid is
BRN
Normally Open
I Jumper Wire (White) 22” 015-0737-40
BRN J Jumper Wire (Black) 22” 015-0737-39
BLK
BLU K Jumper 015-0022-01
D BLK
Capacitor L Jumper Wire (Green - Yellow) 6” 015-0708-35
Jumper Wire (Green - Yellow)
M 015-0708-36
10”
N Jumper Wire (Black) 3 3/4” 015-0741-13
O Jumper Wire (White) 3” 015-0741-16
P Jumper Wire (Black) 5” 015-0741-17
Models: 8000-001, -002, -003, -004, -007, -008 Q Jumper Wire (White) 5” 015-0741-18
Serial Numbers: V933243 thru V1299689 R Back Panel Inlet Harness 015-2677-00
S Harness, Interior Receptacle 015-2688-00

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 7/16/12] D-3 Always verify model & serial number
VetPro® 1000 Wire Diagram - 3
VetPro 1000™
115 VAC Fiber Optics Detailed -007
Model Only
Satelec Scaler (Optional)
Fiber Optics
Components
Components
Power Supply
(Optional)

Control Scaler
Box

I
BLK

Receptacle for
Fiber Optic System
Adjustment
Knob

B Transformer
WHT
H VA1691

BLK
BLK
Fuse
BLK BLK J Air
Switch
BK

A
WH T0.8AL,250V,3AG
GRN/YEL

M
BK

S
WHT

GND
Fan GRN/YEL

BLU Pressure GRN/YEL

L
Back Panel
G
Switch

BRN
F E On/Off
BRN
BRN
Q Power Switch
Wiring Diagram
BLK WHT
BLK
WHT
Item Description Part
BLK BLK O WHT Circuit
Breakers N
Number
Terminal
Block A Transformer Input (White) 015-2713-00
P
BL
WHT WHT
015-2712-00
WHT B Transformer Input (Black)
BLK BLK
BRN C Power Harness 015-2690-00

K C 115 VAC
Power Cord
D Compressor Harness 015-2689-00
Compressor Head Receptacle
E Fan Cord 015-2581-00
R F Jumper Wire (Black) 9” 015-0741-12
Timer
G Jumper Wire (Black) 2 1/2” 015-0737-44
Solenoid
BRN H Jumper Wire (Black) 6” 015-0737-43
Note: Solenoid is
BRN
Normally Open
I Jumper Wire (White) 22” 015-0737-40
BRN J Jumper Wire (Black) 22” 015-0737-39
BLK
BLU K Jumper 015-0022-01
D BLK
Capacitor L Jumper Wire (Green - Yellow) 6” 015-0708-35
Jumper Wire (Green - Yellow)
M 015-0708-36
10”
N Jumper Wire (Black) 3 3/4” 015-0741-13
O Jumper Wire (White) 3” 015-0741-16
P Jumper Wire (Black) 5” 015-0741-17
Models: 8000-001, -002, -003, -004, -007, -008 Q Jumper Wire (White) 5” 015-0741-18
Serial Numbers: V1299690 thru V1456588 R Back Panel Inlet Harness 015-2677-00
S Harness, Interior Receptacle 015-2688-00

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 8/28/13] D-3.1 Always verify model & serial number
VetPro® 1000 Wire Diagram - 4
VetPro 1000™
115 VAC Fiber Optics Detailed -007
Model Only
Satelec Scaler (Optional)
Fiber Optics
Components
Components
Power Supply
(Optional)

Control Scaler
Box

I
BLK

Receptacle for
Fiber Optic System
Adjustment
Knob

B Transformer
WHT
H VA1691

BLK
BLK
Fuse
BLK BLK J Air
Switch
BK

A
WH T0.8AL,250V,3AG
GRN/YEL

M
BK

S
WHT

GND
Fan GRN/YEL

L
GRN/YEL

BLU Pressure
Back Panel
G
Switch

BRN
F E On/Off
BRN
Q Power Switch
BRN
BLK WHT Wiring Diagram
BLK
WHT Item Description Part
BLK BLK O WHT Circuit
Breakers N Number
Terminal
Block
A Transformer Input (White) 015-2713-00
P
BL
WHT WHT

WHT
015-2712-00
BLK BLK
B Transformer Input (Black)
BRN
C Power Harness 015-2690-00
K C 115 VAC
Power Cord
D Compressor Harness 015-2689-00
Compressor Head Receptacle E Fan Cord 015-2581-00
R F Jumper Wire (Black) 9” 015-0741-12
Timer
Solenoid G Jumper Wire (Black) 2 1/2” 015-0737-44
BRN
Note: Solenoid is
H Jumper Wire (Black) 6” 015-0737-43
BRN
Normally Open I Jumper Wire (White) 22” 015-0737-40
BRN

BLK
J Jumper Wire (Black) 22” 015-0737-39
BLU
K Jumper 015-0022-01
D BLK
Capacitor
L Jumper Wire (Green - Yellow) 12” 015-0708-35
M Jumper Wire (Green - Yellow) 16” 015-0708-36
N Jumper Wire (Black) 3 3/4” 015-0741-13
O Jumper Wire (White) 3” 015-0741-16
P Jumper Wire (Black) 5” 015-0741-17
Models: 8000-001, -002, -003, -004, -007, -007S,-008, -008S Q Jumper Wire (White) 5” 015-0741-18
Serial Numbers: R Back Panel Inlet Harness 015-2677-00
V1456589 thru Present S Harness, Interior Receptacle 015-2688-00

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/03/15] D-3.2 Always verify model & serial number
VetPro® 1000 Wire Diagram - Export

VetPro 1000™ Fiber Optics Detailed

230 VAC

Satelec Scaler (Optional)

Fiber Optics
Components
Components
Power Supply
(Optional)

Control Scaler
Box

VA1691-2
BLK

K
Receptacle for

M
Fiber Optic System Adjustment
Knob

WHT

N Transformer
J
BLK
BLK
Fuse
BLK BLK I Air
Switch
T0.8AL,250V,3AG
S
BK

WH GRN/YEL
BK

B
WHT

GND

Fan GRN/YEL

BLU Pressure

F
Back Panel
L
GRN/YEL
Switch

BRN

O D On/Off A
BRN
BRN
Power Switch
Wiring Diagram
BLK
P WHT
BLK Item Description Part Number
WHT

Circuit
C A Jumper Wire (Green- 015-0708-35
BLK BLK
WHT
Breakers Yellow) 6”
Terminal
Block Jumper Wire (Greeen-
B 015-0708-36
Yellow) 10”
E
BL
WHT
WHT
WHT Jumper Wire (Black) 3
C 015-0741-13
BLK BLK 3/4”
BRN
D Jumper Wire (White) 3” 015-0741-16
H 115 VAC E Jumper Wire (Black) 5” 015-0741-17
R Compressor Head
Power Cord
Receptacle F Jumper Wire (White) 5” 015-0741-18

Timer
G G Back Panel Inlet Harness 015-2677-00

Solenoid
H Jumper 015-0022-01
BRN
I Jumper Wire (Black) 22” 015-0737-39
Note: Solenoid is
BRN
Normally Open J Jumper Wire (White) 22” 015-0737-40
BRN

BLK
K Jumper Wire (Black) 10” 015-0737-41
BLU
L Jumper Wire (White) 10” 015-0737-42
Capacitor
M Jumper Wire (Black) 6” 015-0737-43
Jumper Wire (Black) 2
Q N 1/2” 015-0737-44

O Jumper Wire (Black) 9” 015-0741-12

P Fan Cord 015-2581-00

Models: 8000-005 & 8000-006 Q Compressor Harness 015-2689-00

R Power Harness 015-2690-00
Serial Numbers: V1007096 thru V1299689 Harness, Interior Recep-
S 015-2719-00
tacle, Export

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 7/16/12] D-4 Always verify model & serial number
VetPro® 1000 Wire Diagram - Export - 2

VetPro 1000™ Fiber Optics Detailed

230 VAC

Satelec Scaler (Optional)

Fiber Optics
Components
Components
Power Supply
(Optional)

Control Scaler
Box

VA1691-2
BLK

K
Receptacle for

M
Fiber Optic System Adjustment
Knob

WHT

N Transformer
J
BLK
BLK
Fuse
BLK BLK I Air
Switch
T0.8AL,250V,3AG
S
BK

WH GRN/YEL
BK

B
WHT

GND

Fan GRN/YEL

BLU Pressure

F
Back Panel
L
GRN/YEL
Switch

BRN

O D On/Off A
BRN
BRN
Power Switch
Wiring Diagram
BLK
P WHT
BLK Item Description Part Number
WHT

Circuit
C A Jumper Wire (Green- 015-0708-35
BLK BLK
WHT
Breakers Yellow) 6”
Terminal
Block Jumper Wire (Greeen-
B 015-0708-36
Yellow) 10”
E
BL
WHT
WHT
WHT Jumper Wire (Black) 3
C 015-0741-13
BLK BLK 3/4”
BRN
D Jumper Wire (White) 3” 015-0741-16
H 115 VAC E Jumper Wire (Black) 5” 015-0741-17
R Compressor Head
Power Cord
Receptacle F Jumper Wire (White) 5” 015-0741-18

Timer
G G Back Panel Inlet Harness 015-2677-00

Solenoid
H Jumper 015-0022-01
BRN
I Jumper Wire (Black) 22” 015-0737-39
Note: Solenoid is
BRN
Normally Open J Jumper Wire (White) 22” 015-0737-40
BRN

BLK
K Jumper Wire (Black) 10” 015-0737-41
BLU
L Jumper Wire (White) 10” 015-0737-42
Capacitor
M Jumper Wire (Black) 6” 015-0737-43
Jumper Wire (Black) 2
Q N 1/2” 015-0737-44

O Jumper Wire (Black) 9” 015-0741-12

P Fan Cord 015-2581-00

Models: 8000-005 & 8000-006 Q Compressor Harness 015-2689-00

R Power Harness 015-2690-00
Serial Numbers: V1299690 thru V14565898 S
Harness, Interior Recep-
015-2719-00
tacle, Export

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 8/28/13] D-4.1 Always verify model & serial number
VetPro® 1000 Wire Diagram - Export - 3

VetPro 1000™ Fiber Optics Detailed

230 VAC

Satelec Scaler (Optional)

Fiber Optics
Components
Components
Power Supply
(Optional)

Control Scaler
Box

VA1691-2
BLK

K
Receptacle for

M
Fiber Optic System Adjustment
Knob

WHT

N Transformer
J
BLK
BLK
Fuse
BLK BLK I Air
Switch
T0.8AL,250V,3AG
S
BK

WH GRN/YEL
BK

B
WHT
GRN/YEL

GND

Fan GRN/YEL

BLU Pressure

F
Back Panel
L Switch

BRN

O D On/Off A
BRN
BRN
Power Switch
Wiring Diagram
BLK
P WHT
BLK Item Description Part Number
WHT

Circuit
C A Jumper Wire (Green- 015-0708-35
BLK BLK
WHT
Breakers Yellow) 12”
Terminal
Block Jumper Wire (Green-
B 015-0708-36
Yellow) 16”
E
BL
WHT
WHT
WHT Jumper Wire (Black) 3
C 015-0741-13
BLK BLK 3/4”
BRN
D Jumper Wire (White) 3” 015-0741-16
H 115 VAC E Jumper Wire (Black) 5” 015-0741-17
R Compressor Head
Power Cord
Receptacle F Jumper Wire (White) 5” 015-0741-18

Timer
G G Back Panel Inlet Harness 015-2677-00

Solenoid
H Jumper 015-0022-01
BRN
I Jumper Wire (Black) 22” 015-0737-39
Note: Solenoid is
BRN
Normally Open J Jumper Wire (White) 22” 015-0737-40
BRN

BLK
K Jumper Wire (Black) 10” 015-0737-41
BLU
L Jumper Wire (White) 10” 015-0737-42
Capacitor
M Jumper Wire (Black) 6” 015-0737-43
Jumper Wire (Black) 2
Q N 1/2” 015-0737-44

O Jumper Wire (Black) 9” 015-0741-12

P Fan Cord 015-2581-00

Models: 8000-005, 8000-006 & 8000-006S Q Compressor Harness 015-2689-00

R Power Harness 015-2690-00
Serial Numbers: V1456589 thru Present S
Harness, Interior Recep-
015-2719-00
tacle, Export

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/4/15] D-4.2 Always verify model & serial number
VetPro® 1000 Terminal Block Connections

Pressure Switch (Black)

Inside Receptacle (Black)

Transformer (Top - Black)

Compressor (White)

Transformer (Bottom - Black)

Inside Receptacle (White)

Compressor (Green)

Inside Receptacle (Green)

Ground Natural Line

Back Receptacle (Green)

Cart Box Frame (Green)

Back Receptacle (White)

Fan (Black)

Fan (Black)

Back Receptacle (Black)

Models: All All

Serial Numbers: TGC001000Thru TGC001254 V796868 thru V933242

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 8/9/10] D-5 Always verify model & serial number
VetPro® 1000 Terminal Block Connections - 2

Pressure Switch (Black)

Inside Receptacle (Brown)

Transformer (Top - Black)

Compressor (White)

Transformer (Bottom - White)

Inside Receptacle (Blue)

Ground Natural Line

Circuit Breaker (White)

Fan (Black)

Fan (Black)

Circuite Breaker (Black)

Models: All
Serial Numbers: V933243 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 8/9/10] D-5.1 Always verify model & serial number
VetPro® 1000 Tubing Diagram Note
8000-001 Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement is needed use 1/4” yellow
tubing listed in Section E of this manual.

1/4" Gray
1/8" Clear

1/4" Blue
1/8" 1/8"
1/4" Gray Gray 1/4" Blue
Handpiece Gray
1/8" 1/8"
Valve (N.C.)
Blue Blue
3-Way
Push 1/8" Blue
to 1/4" Gray
1/4" Gray
Open 1/8" Blue

1/4"
1/8" Clear
Gray 1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

1/8" Clear
3/8" Blue
Push
1/8" Clear
to
1/8" Clear
Open
1/8" Red Handpiece
1/8" Orange Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Gray

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Orange
1/8" Red
1/4" Gray
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue

1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1244
Models: 8000-001
Serial Numbers: TGC001000 thru TGC001024

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 05/24/2011 D-6 Always verify model & serial number
VetPro® 1000 Tubing Diagram Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
8000-001 The drive air adjustment screws are located on front of Tri-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement is needed use 1/4” yellow
tubing listed in Section E of this manual.

1/4" Gray
1/8" Clear

1/4" Blue 1/8" 1/8"

1/4" Gray Gray 1/4" Blue
Handpiece Gray
1/8" 1/8" Valve (N.C.)
Blue Blue 3-Way
Push 1/8" Blue
to 1/4" Gray
1/4" Gray
Open 1/8" Blue

1/4"
1/8" Clear
Gray 1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

1/8" Clear
3/8" Blue
Push
1/8" Clear
to
1/8" Clear
Open
1/8" Orange Handpiece
1/8" Green
Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Gray

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Green
1/8" Orange
1/4" Gray
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue

1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1244-1
Models: 8000-001
Serial Numbers: TGC001025 thru TGC001244

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 05/24/11 D-6.1 Always verify model & serial number
VetPro® 1000 Tubing Diagram Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
8000-001 & 8000-005 The drive air adjustment screws are located on front of Tri-Block.

1/4" Yellow
1/8" Clear

1/4"
1/4" Blue Yellow
1/4" 1/8" 1/8"
Yellow Gray Blue
Handpiece
1/8" 1/8" Valve (N.C.)
Blue Blue 3-Way
Push 1/8" Blue
1/4" Yellow to 1/4" Yellow
Open 1/8" Blue

1/4"
Yellow 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

3/8" Blue 1/4" Yellow 1/8" Clear

Push
1/8" Clear to
1/8" Clear
Open
1/8" Orange Handpiece
1/8" Green
Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue

1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1244-2

Models: 8000-001 & 8000-005

Serial Numbers: V796868 thru V1043397

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/24/11] D-6.2 Always verify model & serial number
VetPro® 1000 Tubing Diagram Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
8000-001 & 8000-005 The drive air adjustment screws are located on front of Tri-Block.

1/4" Yellow
1/8" Clear

1/4"
1/4" Blue Yellow
1/4" 1/8" 1/8"
Yellow Gray Blue
Handpiece
1/8" 1/8" Valve (N.C.)
Blue Blue 3-Way
Push 1/8" Blue
1/4" Yellow to 1/4" Yellow
Open 1/8" Blue

1/4"
Yellow 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

3/8" Blue 1/4" Yellow 1/8" Clear

Push
1/8" Clear to
1/8" Clear
Open
1/8" Orange Handpiece
1/8" Green
Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue

1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1244-3

Models: 8000-001 & 8000-005

Serial Numbers: V1043398 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/24/2011] D-6.3 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-002 Note
Rear view tubing connections are shown on Dual-Block and Mainfolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement
is needed use 1/4” yellow tubing listed in Section E of this manual.

1/4" Gray
1/8" Clear

1/8" 1/8"
1/4" Blue Gray 1/4" Blue
1/4" Gray
Handpiece Gray
Valve (N.C.)
1/8" 1/8" 3-Way
Blue Blue
Push 1/8" Blue
to 1/4" Gray
1/4" Gray
Open 1/8" Blue

1/4" 1/8" Clear

Gray 1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

3/8" Blue 1/8" Clear

Push
to
1/8" Clear 1/8" Clear
Open
1/8" Red Handpiece
Valve (N.C.)
1/8" Orange
3-Way
1/4" Clear

1/8" Orange 1/4" Gray

1/8" Green 1/8" Orange

1/8" Red
1/4" Gray
1/8" Clear
Syringe 1/8" Clear
1/4" Clear (Typical
Location)
1/8" Clear

1/8" Blue

Handpiece Holders
1/8" Clear 1/8" Blue
1/8" Blue

1/8"
Gray

1/8" Blue

1/8" Blue 1/8"

Blue
1/8" Clear VA1258
1/8" Blue

Models: 8000-002
Serial Numbers: TGC001000 thru TGC001024

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/24/2011] D-7 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-002 Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement
is needed use 1/4” yellow tubing listed in Section E of this manual.

1/4" Gray
1/8" Clear

1/4" Blue 1/8" 1/8"

Gray Blue
1/4"
1/4" Gray
Handpiece Gray
Valve (N.C.)
1/8" 1/8" 3-Way
Blue Blue
Push 1/8" Blue
to 1/4" Gray
1/4" Gray Open 1/8" Blue

1/4" 1/8" Clear

Gray 1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

3/8" Blue
1/8" Clear
Push
to
1/8" Clear 1/8" Clear
Open
1/8" Orange Handpiece
Valve (N.C.)
1/8" Green 3-Way
1/4" Clear

1/8" Orange 1/4" Gray

1/8" Green 1/8" Green

1/8" Orange
1/4" Gray
1/8" Clear
Syringe 1/8" Clear
1/4" Clear (Typical
Location)
1/8" Clear

1/8" Blue

Handpiece Holders
1/8" Clear 1/8" Blue
1/8" Blue

1/8"
Gray

1/8" Blue

1/8" Blue 1/8"

Blue
1/8" Clear VA1258-1
1/8" Blue

Models: 8000-002
Serial Numbers: TGC001025 thru TGC001244

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/24/2011] D-7.1 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-002 Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.

1/4" Yellow
1/8" Clear

1/4" Yellow
1/4" Blue 1/8" 1/8"
Gray Blue
1/4"
Yellow
Handpiece
Valve (N.C.)
1/8" 3-Way
Blue
Push 1/8" Blue
1/8" to 1/4" Yellow
Blue 1/4" Yellow Open 1/8" Blue

1/4"
Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

3/8" Blue 1/8" Clear

Push
to
1/8" Clear 1/8" Clear
Open
1/8" Orange Handpiece
Valve (N.C.)
1/8" Green 3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/8" Green

1/8" Orange
1/4" Yellow
1/8" Clear
Syringe 1/8" Clear
1/4" Clear (Typical
Location)
1/8" Clear

1/8" Blue

Handpiece Holders
1/8" Clear 1/8" Blue
1/8" Blue

1/8"
Gray

1/8" Blue

1/8" Blue 1/8"

Blue
1/8" Clear VA1258-2
1/8" Blue

Models: 8000-002
Serial Numbers: V796868 thru V1043397

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 4/25/2011] D-7.2 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-002 Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.

1/4" Yellow
1/8" Clear

1/4" Yellow
1/4" Blue 1/8" 1/8"
Gray Blue
1/4"
Yellow
Handpiece
Valve (N.C.)
1/8" 3-Way
Blue
Push 1/8" Blue
1/8" to 1/4" Yellow
Blue 1/4" Yellow Open 1/8" Blue

1/4"
Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

3/8" Blue 1/8" Clear

Push
to
1/8" Clear 1/8" Clear
Open
1/8" Orange Handpiece
Valve (N.C.)
1/8" Green 3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/8" Green

1/8" Orange
1/4" Yellow
1/8" Clear
Syringe 1/8" Clear
1/4" Clear (Typical
Location)
1/8" Clear

1/8" Blue

Handpiece Holders
1/8" Clear 1/8" Blue
1/8" Blue

1/8"
Gray

1/8" Blue

1/8" Blue 1/8"

Blue
1/8" Clear VA1258-3
1/8" Blue

Models: 8000-002
Serial Numbers: V1043398 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 4/25/11] D-7.3 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-003 Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement is
needed use 1/4” yellow tubing listed in Section E of this manual.

1/8" Clear

1/4"
Gray
1/4" Blue 1/4" 1/8" 1/8"
Gray Gray Blue
Handpiece
1/8" Valve (N.C.)
1/8"
Blue 3-Way
Blue
Push 1/8" Blue
1/4" Gray to
Open 1/8" Red
1/8" Blue

1/4" Gray
1/4"
Gray 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray 1/8" Blue

1/4" Gray 1/8" Clear

3/8" Blue
Push
1/8" Clear to
1/8" Clear
Open
1/8" Orange Handpiece
1/8" Green
Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Gray

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Green
1/8" Orange
1/4" Gray
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue
1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1372
Models: 8000-003
Serial Numbers: TGC001000 Thru TGC001244

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/24/2011] D-8 Always verify model & serial number
VetPro® 1000 Tubing Diagram Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
8000-003 & 8000-006 & 8000-008 The drive air adjustment screws are located on front of Tri-Block.

1/4" Yellow
1/8" Clear

1/4"
Yellow
1/4" Blue 1/4" 1/8" 1/8"
Yellow Gray Blue
Handpiece
1/8" Valve (N.C.)
1/8"
Blue 3-Way
Blue
Push 1/8" Blue
1/4" Yellow to
Open 1/8" Red
1/8" Blue

1/4" Yellow
1/4"
Yellow 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

1/4" Yellow 1/8" Clear

3/8" Blue
Push
1/8" Clear to
1/8" Clear
Open
1/8" Orange Handpiece
1/8" Green
Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue
1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1372-2

Models: 8000-003 & 8000-006 & 8000-008

Serial Numbers: V796868 thru V1043397

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 6/20/12] D-8.1 Always verify model & serial number
VetPro® 1000 Tubing Diagram Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
8000-003 & 8000-006 & 8000-008 The drive air adjustment screws are located on front of Tri-Block.

1/4" Yellow
1/8" Clear

1/4"
Yellow
1/4" Blue 1/4" 1/8"
Yellow 1/8" Blue
Handpiece Gray

1/8" Valve (N.C.)

1/8"
Blue 3-Way
Blue
Push 1/8" Blue
1/4" Yellow to
Open 1/8" Red
1/8" Blue

1/4" Yellow
1/4"
Yellow 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

1/4" Yellow 1/8" Clear

3/8" Blue
Push
1/8" Clear to
1/8" Clear
Open
1/8" Orange Handpiece
1/8" Green
Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue
1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1372-3

Models: 8000-003 & 8000-006 & 8000-008

Serial Numbers: V1043398 thru V1271515

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 8/7/12] D-8.2 Always verify model & serial number
VetPro® 1000 Tubing Diagram Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
8000-003 & 8000-006 & 8000-008 The drive air adjustment screws are located on front of Tri-Block.

1/4" Yellow
1/8" Clear

1/4"
Yellow
1/4" Blue 1/4" 1/8"
Yellow 1/8" Blue
Handpiece Gray

1/8" Valve (N.C.)

1/8"
Blue 3-Way
Blue
Push 1/8" Blue
1/4" Yellow to
Open 1/8" Red
1/8" Blue

1/4" Yellow
1/4"
Yellow 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

1/4" Yellow 1/8" Clear

3/8" Blue
Push
1/8" Clear to
1/8" Clear
Open
1/8" Orange Handpiece
1/8" Green
Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue
1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1372-4

Models: 8000-003, 8000-006, 8000-006S, 8000-008 & 8000-008S

Serial Numbers: V1271516 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/7/15] D-8.3 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-004 Note
Rear view tubing connections are shown on Dual-Block and Manifolds for clarity. The drive
air adjustment screws are located on front of Dual-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement is needed use
1/4” yellow tubing listed in Section E of this manual.

1/4" Gray
1/8" Clear
1/4"
Gray
1/8" 1/8"
Gray Blue
1/4" Gray
Handpiece
Valve (N.C.)
1/8" 1/8" 3-Way
Blue Blue Push 1/8" Blue
to
1/8" Red
1/4" Gray Open 1/8" Blue

1/4" 1/8" Clear

Gray 1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

1/4" Gray

3/8" Blue 1/8" Clear

Push
to
1/8" Clear 1/8" Clear
Open
1/8" Orange Handpiece
Valve (N.C.)
1/8" Green 3-Way
1/4" Clear

1/8" Orange 1/4" Gray

1/8" Green 1/8" Green

1/8" Orange
1/4" Gray
1/8" Clear
Syringe 1/8" Clear
1/4" Clear (Typical
Location)
1/8" Clear

1/8" Blue

Handpiece Holders
1/8" Clear 1/8" Blue
1/8" Blue

1/8"
Gray

1/8" Blue

1/8" Blue 1/8"

Blue
1/8" Clear VA1373
1/8" Blue

Models: 8000-004
Serial Numbers: TGC001000 Thru TGC001244

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/24/11] D-9 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-004 Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.

1/4" Yellow
1/8" Clear
1/4"
Yellow
1/8" 1/8"
1/4" Blue 1/4" Gray Blue
Yellow Handpiece
Valve (N.C.)
1/8" 1/8" 3-Way
Blue Blue Push 1/8" Blue
to
1/8" Red
1/4" Yellow Open 1/8" Blue

1/4"
Yellow 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

1/4"
Yellow
3/8" Blue
Push 1/8" Clear
to
1/8" Clear 1/8" Clear
Open
1/8" Orange Handpiece
Valve (N.C.)
1/8" Green 3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/8" Green

1/8" Orange
1/4" Yellow
1/8" Clear
Syringe 1/8" Clear
1/4" Clear (Typical
Location)
1/8" Clear

1/8" Blue

Handpiece Holders
1/8" Clear 1/8" Blue
1/8" Blue

1/8"
Gray

1/8" Blue

1/8" Blue 1/8"

Blue
1/8" Clear VA1373-1
1/8" Blue

Models: 8000-004
Serial Numbers: V796868 thru V1043397

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 4/25/11] D-9.1 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-004 Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.

1/4" Yellow
1/8" Clear
1/4"
Yellow
1/8"
1/4" Blue 1/4" 1/8" Blue
Yellow Handpiece Gray
Valve (N.C.)
1/8" 1/8" 3-Way
Blue Blue Push 1/8" Blue
to
1/8" Red
1/4" Yellow Open 1/8" Blue

1/4"
Yellow 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray
1/4"
Yellow
3/8" Blue
Push 1/8" Clear
to
1/8" Clear 1/8" Clear
Open
1/8" Orange Handpiece
Valve (N.C.)
1/8" Green 3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/8" Green

1/8" Orange
1/4" Yellow
1/8" Clear
Syringe 1/8" Clear
1/4" Clear (Typical
Location)
1/8" Clear

1/8" Blue

Handpiece Holders
1/8" Clear 1/8" Blue
1/8" Blue

1/8"
Gray

1/8" Blue

1/8" Blue 1/8"

Blue
1/8" Clear VA1373-2
1/8" Blue

Models: 8000-004
Serial Numbers: V1043398 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 4/25/11] D-9.2 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-007
Note
Rear view tubing connections are shown on Quad-Block and Manifolds for 1/8" Clear

clarity. The drive air adjustment screws are located on front of Quad-Block. Handpiece
1/4"
Yellow
1/8" 1/8"
Valve (N.C.) Gray Blue
3-Way

Push
1/8" Blue
to 1/8" Red
Open
1/4" Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/4"
1/4" Blue 1/4" 1/8" Yellow 1/8"
Yellow Gray Blue
Handpiece
1/8" Valve (N.C.)
1/8"
Blue 3-Way
Blue
Push 1/8" Blue
1/4" Yellow to
Open 1/8" Red
1/8" Blue

1/4" Yellow
1/4"
Yellow 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

1/4" Yellow 1/8" Clear

3/8" Blue
Push
1/8" Clear to
1/8" Clear
Open
1/8" Orange Handpiece
1/8" Green
Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue
1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1638

Models: 8000-007
Serial Numbers: V933243 thru V1043397

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 6/20/12] D-10 Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-007
Note
Rear view tubing connections are shown on Quad-Block and Manifolds for 1/8" Clear

clarity. The drive air adjustment screws are located on front of Quad-Block. 1/4"
Yellow
Handpiece 1/8" 1/8"
Valve (N.C.) Gray Blue
3-Way

Push
1/8" Blue
to 1/8" Red
Open
1/4" Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/4"
1/4" Blue 1/4" Yellow 1/8"
Yellow Blue
1/8"
Handpiece
Gray
1/8" Valve (N.C.)
1/8"
Blue 3-Way
Blue
Push 1/8" Blue
1/4" Yellow to
Open 1/8" Red
1/8" Blue

1/4" Yellow
1/4"
Yellow 1/8" Clear
1/16" I.D. Gray
Syringe Tube 1/8" Blue
1/8"
Gray

1/4" Yellow 1/8" Clear

3/8" Blue
Push
1/8" Clear to
1/8" Clear
Open
1/8" Orange Handpiece
1/8" Green
Valve (N.C.)
3-Way
1/4" Clear

1/8" Orange 1/4" Yellow

1/8" Green 1/16" I.D. Gray
Syringe Tube 1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/8" Clear
1/4" Clear
Push
to
Open
Handpiece
1/8" Blue Valve (N.C.) 1/8" Clear
3-Way 1/8"
Clear

1/8" Blue
1/8" Clear

Syringe
1/8" Clear
(Typical 1/8" Red
Location)

1/8" Blue
1/8" Blue

1/8" Blue 1/8" 1/8"

Blue Gray
1/8" Clear Handpiece Holders 1/8" Blue
1/8" Blue

VA1638-1
Models: 8000-007 & 8000-007S
Serial Numbers: V1043398 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 6/20/12] D-10.1 Always verify model & serial number
Tri-Block
Rear View

Handpiece Coolant Water

Handpiece Coolant Air

Coolant Water

Coolant Air
Holder Handpiece
Drive Air (Typical 3 Places)

Pressure Gauge

Handpiece Drive Air

Note
Rear view tubing connections are shown on Tri-Block for clarity.
Connections are the same for Dual Block minus one handpiece.

Isometric Rear View

Models: All
Serial Numbers: TGC001000 thru TGC001024

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 8/28/08] D-11 Always verify model & serial number
Tri-Block
Rear View

Handpiece Coolant Water

Handpiece Coolant Air

Coolant Water

Coolant Air
Holder Handpiece
Drive Air (Typical 3 Places)

Pressure Gauge

Handpiece Drive Air

Note
Rear view tubing connections are shown on Tri-Block for clarity.
Connections are the same for Dual Block minus one handpiece.
SN beginning with TGC have large grey tubing.
SN beginning with V have large Yellow tubing.
Isometric Rear View

Models: All
Serial Numbers: TGC001025 Thru TGC001244

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 1/19/2010] D-11.1 Always verify model & serial number
Tri-Block
Rear View
Handpiece Coolant Water

Handpiece Coolant Air

Coolant Water

Coolant Air
Holder Handpiece
Drive Air (Typical 3 Places)

Pressure Gauge

Handpiece Drive Air

Note
Rear view tubing connections are shown on Tri-Block for clarity.
Connections are the same for Dual Block minus one handpiece.
SN beginning with TGC have large grey tubing.
SN beginning with V have large Yellow tubing.
Isometric Rear View

Models: All
Serial Numbers: V796868 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 6/16/10] D-11.2 Always verify model & serial number
Quad-Block
Rear View

Handpiece Coolant Water

Handpiece Coolant Air

Coolant Water

Coolant Air
Holder Handpiece
Drive Air (Typical 4 Places)

Pressure Gauge

Handpiece Drive Air

Isometric Rear View Note

Rear view tubing connections are
shown on Quad-Block for clarity.

Models: 8000-007 & 8000-007S

Serial Numbers: V933243 thru Present

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/7/15] D-12 Always verify model & serial number
 Exploded Views & Vet Pro 1000.......................................E2

Parts Lists
Section E
XXX-XXXX-XX

XXX-XXXX-XX

XXX-XXXX-XX

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: dd/mo/yr] E-1

VetPro® 1000 Fiber Optic Components ........................E-15*
Fiber Optic Electrical Components.........E-18*
Panel Components...... E-8*

Upper Compartment.... E-5*

Delivery....................... E-6*

Water System.............. E-7*

Middle Compartment... E-4*

Lower Compartment.... E-3*

Earlier Production Model Shown

Frame and Back Components ............E-9*

Athena Handpieces and Maintenance............E-12

Athena Replacement Components ................E-17
Foot Control Assembly ........E-11 Midmark Brand Handpieces and Parts ..........E-13

Tubing & Fittings.......... E-10* Syringe........................ E-14

Handpiece Holders...... E-17 Scaler.......................... E-15

Models: All * Indicates multiple pages due to a serial

Serial Numbers: all number break for the parts illustration.

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/21/11] E-2 Always verify model & serial number
 1 a) 015-2390-00
b) 002-1145-00

015-2394-00 21 2 014-0182-00

3 014-0660-00

4 a) 002-1149-00
b) 10589100
015-2395-00 20
2
5 014-0218-03
041-0006-02 19 014-10066-00 22

002-1143-00 23 Lower Compartment Components

016-1195-00 18 6 014-0023-01 Description Qty.
a) Replacement Compressor Head (includes
040-0250-79 17 1
capacitor)
b) Head Rebuild Kit (refer to ”Installation: (Com- 1
pressor Head Rebuild Kit” [642648A-0605] in
Repair Kits folder for Installation Instructions)

041-0250-13 16 2 Hex Nipple (1/4” NPT) 3

7 014-0645-00 3 ST Elbow (1/4” NPT) 1
a) Filter Element Only
4 1
b) Muffler, Plastic, Assembly
5 Elbow Union (1/4” NPT) 1
6 Hex Bushing (3/8” MPT x 1/4” FPT) 1
016-1194-00 15 8 014-0648-00 7 Check Valve 1
8 Barb Fitting (1/2” x 3/8” MPT) 1
9 Allen Plug (1/8” MPT) 1
9 61901406 Solenoid (Includes Item #9)
10 a) Domestic 1
040-0250-79 14 10 a) 002-1148-00
b) Export
11 Compressor Plate 1
b) 014-0694-00
12 Pan Head Screw (6/32” x 1/2”) 1
040-0006-108 13 VA1286
13 Screw (0.138-32 X 0.375) 2
14 Hex Head Screw (1/4 20” x 1/2”) 1
11 050-7581-00-232 15 Vibration Mount 4
16 Hex Nut (1/2 13”) 4
12 040-0006-27 17 Screw (0.250-20 X 0.625) 1
18 Bubble Mount 4
19 Kep Nut (6/32”) 8
20 Strap Loop 2
Models: All 21 Capacitor 1

Serial Numbers: 22 Nipple (formerly zinc plate steel, now brass) 1

TGC001000 Thru TGC001254
23 Muffler, Bronze 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 12/28/18] E-3 Always verify model & serial number
 1 a) 015-2390-00
b) 015-2668-00
c) 002-1145-00

2 014-0317-02

040-0008-79 21
3 014-0194-01

a) 015-2394-00 20 4 a) 002-1149-00
b) 015-2676-00
b) 10589100

6 Lower Compartment Components

015-2395-00 19 014-0023-01
Item Description Qty.

041-0006-02 18 014-10066-00 22 a) Compressor Head, Dom. (includes capacitor)

5 014-0218-03 1
b) Compressor Head, Export (includes capacitor)
c) Head Rebuild Kit (refer to ”Installation: (Com- 1
pressor Head Rebuild Kit” [642648A-0605] in
016-1195-00 17 002-1143-00 23 Repair Kits folder for Installation Instruction.)
2 Hex Nipple (1/4” NPT) 3
3 ST Elbow (1/4” NPT) 1
040-0250-79 16 4 a) Filter Element Only 1
b) Plastic Muffler Assembly
5 Elbow Union (1/4” NPT) 1
6 Hex Bushing (3/8” MPT x 1/4” FPT) 1
7 014-0645-00 7 Check Valve 1
041-0250-13 15 8 Barb Fitting (1/2” x 3/8” MPT) 1
9 Allen Plug (1/8” MPT) 1
Solenoid (Includes Item #9)
10 a) Domestic 1
8 014-0648-00 b) Export
11 Compressor Plate 1

016-1194-00 14 12 Screw (0.138-32 X 0.375) 2

9 61901406 13 Hex Head Screw (1/4 20” x 1/2”) 1
14 Vibration Mount 4
15 Hex Nut (1/2 13”) 4
040-0250-79 13 16 Screw (0.250-20 X 0.625) 1
10 a) 002-1148-00 17 Bubble Mount 1
b) 014-0694-00 VA1286-1
040-0006-108 12 18 Kep Nut (6/32”) 8
11 050-7581-00-232 19 Strap Loop 2
Capacitor
20 a) Domestic Models 1
b) Export Models (-005 & -006)
Models: All 21 Pan Head Screw (6/32” x 1/2”) 2
Serial Numbers: V796868 thru V1299689 22 Nipple (formerly zinc plate steel, now brass) 1
23 Muffler, Bronze 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 12/28/18] E-3.1 Always verify model & serial number
 1 a) 015-2390-00
b) 015-2668-00
c) 002-1145-00

2 014-0317-02
040-0008-79 22
3 014-0194-01

a) 015-2394-00 21 4 a) 002-1149-00
b) 015-2676-00
b) 10589100

015-2395-00 20
Lower Compartment Components
041-0006-02 19 014-0023-01 6 Item Description Qty.
a) Compressor Head, Dom. (includes capacitor)
b) Compressor Head, Export (includes capacitor)
016-1195-00 18 014-10066-00 23 1 c) Head Rebuild Kit (refer to ”Installation: (Com- 1
5 014-0218-03 pressor Head Rebuild Kit” [642648A-0605] in
Repair Kits folder for Installation Instruction.)
22 2 Hex Nipple (1/4” NPT) 3
002-1143-00 24
3 ST Elbow (1/4” NPT) 1
62970706 17 4 a) Filter Element Only
b) Plastic Muffler Assembly 1

5 Elbow Union (1/4” NPT) 1

040-0250-79 16 6 Hex Bushing (3/8” MPT x 1/4” FPT) 1
7 Check Valve 1
7 014-0645-00 8 Barb Fitting (1/2” x 3/8” MPT) 1
9 Allen Plug (1/8” MPT) 1
041-0250-13 15 Solenoid (Includes Item #9)
10 a) Domestic 1
b) Export
8 014-0648-00 11 Compressor Plate 1
12 Screw (0.138-32 X 0.375) 2

016-1194-00 14 13 Hex Head Screw (1/4 20” x 1/2”) 1

9 61901406 14 Vibration Mount 4
15 Hex Nut (1/2 13”) 4
16 Screw (0.250-20 X 0.625) 1
040-0250-79 13
17 3-Pole Terminal Block 1
10 a) 002-1148-00 18 Bubble Mount 1
b) 014-0694-00 VA1286-2
040-0006-108 12 19 Kep Nut (6/32”) 8
11 050-7581-00-232 20 Strap Loop 2
Capacitor
21 a) Domestic Models 1
b) Export Models (-005 & -006)
Models: All 22 Pan Head Screw (8/32” x 1/2”) 6
Serial Numbers: V1299690 thru V2073554 23 Nipple (formerly zinc plate steel, now brass) 1
24 Muffler, Bronze 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 1/8/2019] E-3.2 Always verify model & serial number
 1 a) 015-2390-00
b) 015-2668-00
c) 002-1145-00

2 014-0317-02
040-0008-79 22
3 014-0194-01

a) 015-2394-00 21 4 a) 002-1149-00
b) 015-2676-00
b) 10589100

015-2395-00 20
Lower Compartment Components
Item Description Qty.
041-0006-02 19 014-10066-00 23 a) Compressor Head, Dom. (includes capacitor)
5 014-0218-03 1
b) Compressor Head, Export (includes capacitor)
c) Head Rebuild Kit (refer to ”Installation: (Com- 1
016-1195-00 18 pressor Head Rebuild Kit” [642648A-0605] in
Repair Kits folder for Installation Instruction.)
6 014-0023-01 2 Hex Nipple (1/4” NPT) 3
22 3 ST Elbow (1/4” NPT) 1
a) Filter Element Only
4 1
002-1143-00 24 7 014-0645-00 b) Plastic Muffler Assembly
62970706 17 5 Elbow Union (1/4” NPT) 1

PCB50640 25 6 Hex Bushing (3/8” MPT x 1/4” FPT) 1

040-0250-79 16 8 61901406 7 Check Valve 1
8 Allen Plug (1/8” MPT) 1
Solenoid (Includes Item #8)
9 a) 002-1148-00 9 a) Domestic 1
b) 014-0694-00 b) Export
041-0250-13 15 10 Barb Fitting (1/2” x 3/8” MPT) 1
11 Compressor Plate 1
12 Screw (0.138-32 X 0.375) 2
10 014-0648-00
13 Hex Head Screw (1/4 20” x 1/2”) 1

016-1194-00 14 14 Vibration Mount 4

15 Hex Nut (1/2 13”) 4
16 Screw (0.250-20 X 0.625) 1
17 3-Pole Terminal Block 1
040-0250-79 13
18 Bubble Mount 1
19 Kep Nut (6/32”) 8
VA1286-3
040-0006-108 12 20 Strap Loop 2
11 050-7581-00-232 Capacitor
21 a) Domestic Models 1
b) Export Models (-005 & -006)
22 Pan Head Screw (8/32” x 1/2”) 6
Models: All 23 Nipple 1
Serial Numbers: V2073554 thru Present 24 Muffler, Bronze 1
25 Elbow (3/8” MPT) 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 1/8/2019] E-3.3 Always verify model & serial number
 041-0008-04 17

050-7602-00-232 16
1 040-0010-144

014-0689-00 15

015-2398-00 14
2 015-2397-00

62970707 13
18 002-1574-00

041-0006-02 12
12 1

015-2399-00 11
10572400 10

Middle Compartment Components

Item Description Qty.
VA1292 1 Pan Head Screw (10/32 x 1/2”) 9
1 2 Transformer (Scaler Models Only) 1
3 Screw 4
4 Circuit Breaker 1
5 Receptacle, Double 1
3 040-0006-105 6 AC Connector Receptacle 1
040-0006-108 9 7 Screw (6/32” x 1/2”) 3
8 Switch, Rocker 1
4 015-2400-00 9 Pan Head Screw (6/32 X.375) 1
015-2191-01 8 10 Fan, 115 VAC (115V Models only) 1
4 5 015-0083-02 11 Timer, Interval 1
12 Kep Nut (6/32”) 20
015-2403-00 6
040-0006-27 7 13 Terminal Block 1
14 Pressure Switch 1
15 90° Elbow, 1/4" Compression x 1/4" NPT 1
Models: All 16 Bracket 1
Serial Numbers: TGC001000 Thru TGC001254 17 Kep Nut (8/32”) 12
19 Power Cord 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/3/2015] E-4 Always verify model & serial number
 1 040-0008-79
050-7602-00-232 15

014-0689-00 14 2 040-0010-47

015-2398-00 13
3 015-2397-00

62970707 12

16 002-1574-00
040-0006-27 11 2

015-2399-00 10

10572400 9

Middle Compartment Components

4 015-0083-02
Item Description Qty.
040-0006-108 8 1 Pan Head Screw .164-32 x .500 4
2 Pan Head Screw 10-24 X 3/8 8
3 Transformer (Scaler Models Only) 1
5 015-2400-00 4 Receptacle, Double 1
015-2191-01 7 5 Circuit Breaker 1
6 AC Connector Receptacle 1
7 Rocker Switch 1
8 Pan Head Screw 6-32X.375 BO 1
6 015-0639-01 9 Fan, 115 VAC (115V Models only) 1
5 10 Timer, Interval 1
VA1292-1 11 Pan Head Screw 6-32 x 1/2” 2
12 Terminal Block 1
13 Pressure Switch 1
Models: All 14 90° Elbow, 1/4" Compression x 1/4" NPT 1
15 Bracket 1
Serial Numbers: V796868 thru V933242
16 Power Cord 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 11/3/2015] E-4.1 Always verify model & serial number
 1 040-0008-79
050-7602-00-232 15

014-0689-00 14
2 015-2703-00
015-2398-00 13
3 015-1534-00

62970707 12 1

16 a) 002-1574-00 1 4 62502416
b) 015-0363-00
015-2399-00 11
5 015-0346-48

6 040-0010-129
a) 10572400 10
b) 015-2667-00

Middle Compartment Components

Item Description Qty.
1 Pan Head Screw .164-32 x .500 12
015-2714-00 9
2 Transformer (Scaler Models Only) 1
3 Fuseblock (1/4” x 1 1/4”) 1
4 Screw (Pan Head .138-32 x .500) 1
Circuit Breaker 5 Fuse, 3 AG, Slo-Blo, 800mA, 250V 1
Overload % Trip Times 6 Screw (10-24 x 1/2” Pan Head Phillips) 4
100 % No Trip 7 AC Connector Receptacle 1

135 % 1 Hour Circuit Breaker

8 a) Domestic (6 amp.) 2
200 % 2.2 - 15 sec b) Export (3 amp.)
a) 015-2711-00 8 400 % 0.55 - 1.8 sec 9 Rocker Switch 1
b) 015-2711-01 Fan
600 % 0.27 - 0.7 sec 10 a) Domestic 1
b) Export
800 % 0.17 - 0.45 sec
11 Timer, Interval 1
015-0639-01 7 1000 % 0.12 - 0.3 sec VA1292-2
12 Terminal Block 1
13 Pressure Switch 1
14 90° Elbow, 1/4" Compression x 1/4" NPT 1
Models: All 15 Bracket 1
Power Cord
Serial Numbers: V933243 thru Present 16 a) Domestic 1
b) Export Models (-005 & -006)

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 11/3/2015] E-4.2 Always verify model & serial number
 040-0312-41 20

1 014-0651-01

2 014-0652-00

3 014-0698-00
002-10301-00 19
15

12
18 4 014-0176-55

1
014-0656-00 17

Upper Compartment Components

014-0655-00 16 Item Description Qty.
1 Air Tank Container (Lid and tank) 1
2 Adapter (1” MPT x 1/4” FPT) 2
002-1144-00 15 3 Fitting, Compression Stem (1/4 MPT X 1/4
4 O-ring 1
122841 14 5 Elbow St (1/4” NPT) 1
6 Nipple (1/4” MPT x 3”) 1
121533 13 7 Shut-Off Valve (1/4” NPT) 1
8 Tube Connector (1/4” x 1/4” MPT) 1

041-0008-04 12 9 • Items 8-12 Only In Models with Fiber Optics

Screw (6/32” x 1/2”) 1
014-0653-00 8 5 10 Receptacle Cover - Duplex 1
015-0083-01 11 11 Receptacle - Duplex 1
5 014-0194-01
014-0619-00 7 12 Nut (8/32”) 4
13 Electrical - Duplex 1
015-2586-00 10 14 Pressure Gauge (1/8” NPT) 1
6 014-0182-02 15 Replacement Filter
040-0006-27 9 VA1294
16 Tee Union 3
17 Stem Adapter (1/4” x 1/8”) 1
18 Regulator (order item 19) 1

Regulator Bracket Assembly Kit (Includes Items

19 1
#14-18)
Models: All 20 Cap Screw (5/16-18” x 1”) 4
Serial Numbers: TGC001000 thru TGC001254 Not Shown - 015-0371-01
21 1
Drain Valve Hose Clip

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 1/14/2019] E-5 Always verify model & serial number
 040-0312-41 20

1 014-0651-01

2 014-0652-00

002-10301-00 19 3 014-0698-00

15
12
18 4 014-0176-55

1
014-0656-00 17

014-0655-00 16 Upper Compartment Components

Item Description Qty.
002-1144-00 15 1 Air Tank Container (Lid and tank) 1
2 Adapter (1” MPT x 1/4” FPT) 2
122841 14 3 Fitting, Compression Stem (1/4 MPT X 1/4
4 O-ring 1
5 Elbow St (1/4” NPT) 1
121533 13 6 Nipple (1/4” MPT x 3”) 1
7 Shut-Off Valve (1/4” NPT) 1
77009189 12 8 Tube Connector (1/4” x 1/4” MPT) 1
• Items 8-12 Only In Models with Fiber Optics
014-0653-00 8 5 9 Screw (6/32” x 1/2”) 1

015-0083-01 11 5 014-0194-01
10 Receptacle Cover - Duplex 1
11 Receptacle - Duplex 1
014-0619-00 7 12 Nut (8/32”) 4
015-2586-00 10 6 014-0182-02 13 Electrical - Duplex 1
14 Pressure Gauge (1/8” NPT) 1
VA1294-1
15 Replacement Filter
040-0006-27 9 16 Tee Union 3
17 Stem Adapter (1/4” x 1/8”) 1
18 Regulator (order item 19)
Regulator Bracket Assembly Kit (Includes Items
19
Models: All #14-18)
20 Cap Screw (5/16-18” x 1”) 4
Serial Numbers: V796868 thru V933242 21 Not Shown - 015-0371-01 1
Drain Valve Hose Clip

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 1/14/2019] E-5.1 Always verify model & serial number
 016-1219-00 3 014-0344-00 1

014-0698-00 4 040-0250-133 2
15 002-10301-00

014-0655-00 5

16

014-0348-00 6

014-0653-00 7
5

014-0656-00 12
014-0619-00 8
Upper Compartment Components
002-1144-00 13 Item Description Qty.
014-0182-02 9 1 Hex Head Plug (1/4” NPT Brass) 1
VA1294-2
2 Hex Head Whiz Lock (1/4”-20 x 1/2”) 3
014-0194-01 10 122841 14 3 Pressure Tank, One GAL 1
4 Adapter Stem (1/4” MPT x 1/4”) 1

11 17
5 Tee Union 3
6 Barb Fitting (3/8” ) 1
7 Connector (1/4”MPT x 1/4” TB) 1
8 Shut off Valve (1/4” NPT) 1
9 Pipe Nipple (1/4” MPT x 3”) 1
10 90 degree Elbow (1/4” x 1/4”) 1
11 Regulator (order item 15) 1
12 Adapter Stem (1/8” MPT x 1/4”) 2
13 Regulator Filter Element Kit
14 Pressure Gauge (1/8” NPT, 0-130 PSI) 1
Models: All 15 Regulator Bracket Assembly Kit (Includes Items
#5 {2} and 11-14)
Serial Numbers: V933243 thru Present 16 Screw 1
17 Refer to: Fiber Optic Electrical Components

© Midmark Corporation 2008 SF-1925

004-0586-00 [Revised: 1/14/2019]
E-5.2 Always verify model & serial number
 050-7615-00-232 19
1 122582
a) 029-4651-00 18 041-0006-02 20 2 117585
b) 029-4651-02

4 029-2449-03 5 a) 050-7612-00-232
3 b) 050-7613-00-232

3 6 053-1165-01

7 014-0666-00
029-4652-00 17
8 040-0006-53

AR = as required
Delivery System Components
Item Description Qty.
1 Loop Strap 1
9 040-0006-27
2 Water Relay 1
20 3 Refer to: Tubing & Fittings AR
4 Air Control Valve AR
a) Delivery Control Panel - with Scaler
5 1
b) Delivery Control Panel - without Scaler
6 Knob, blue (includes set screw) AR
VA1298
7 Gauge with Bracket 1
8 Pan Head Screw (6/32” x 1/4”) AR
9 Pan Head Screw (6/32” x 1/2”) 2

050-7614-00-232 12 10 a) 029-4655-00 10
a) Syringe Holder
b) Universal Holder AR
a) 029-4650-00 15 b) 029-4656-00 c) Pilot Valve - Handpiece - Repair
9 c) 002-1146-00 11 Bar Holder 1
b) 029-4657-00
12 Bracket 1

040-0004-00 14 051-1203-00-232 11 13 Bracket (Block) 1

14 Pan Head Screw (4-40x 1/4”) 2
a) Tri-Block (Models 8000-001 & 8000-003)
15 1
050-7616-00-232 13 b) Dual-Block (Models 8000-002 & 8000-004)
Not Shown - 002-1147-00
16 1
Tri-Block Replacement Membrane Repair Kit
17 Manifold Assembly (Syringe) 1
Models: All 18 Manifold Assembly a) Handpiece b) Scaler AR
Serial Numbers: TGC001000 Thru TGC001254 19 Delivery Back Box 1
20 Kep Nut (6/32”) AR

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 10/26/15] E-6 Always verify model & serial number
 Air Control Valve Valve
Assembly includes: 22 050-7873-00-232

Lock
Trim
Nut
Washer 040-0010-129 21

040-0004-00 20
1 a) 029-4650-00
b) 029-4657-00
029-2449-03 19

a) 050-11482-00-232 18 2 041-0006-02
b) 050-7871-00-232
15 3 050-7616-00-232
053-1165-01 17
AR = as required
Delivery System Components
014-0666-00 15
Item Description Qty.
a) Tri-Block (Models 8000-001 & 8000-003)
1 1
b) Dual-Block (Models 8000-002 & 8000-004)
4 a) 029-4651-01 2 Nut #6-32 KEPS W/Starwasher AR
b) 029-4651-00 3 Bracket (Tri-Block) 1
16 c) 029-4651-02 Handpiece blocks (Facing Front - Left to Right)
d) 029-4652-00 a) Fiber Optic (Models 8000-003 & 800-004)
4 b) Manifold Assy, Handpiece 1 EA
c) Manifold Assy. Scaler
d) Mainfold, Syringe
5 050-7874-00-232 5 Block Bracket 1
10 040-0010-47 6 Screw Pan Head (6-32X.375) 2
7 Refer to: Tubing & Fittings AR
6 040-0006-108 8 Valve, C.W. Control 1
9 Clamp (11/16”) 1
12 040-0010-74 10 Screw (#10-24 x 3/8”) 2
040-0008-06 14 7 11 Lock Washer 2

P12575 11 12 Screw Pan Head PHL (10-32 x 3/8”) 2

8 117585 13 Handpiece Holder Assembly, Four Position 1
002-10300-00 13 16 14 Screw Mach, Pan Head PHL (8-32 x 1/2) 4
15 Gauge, Panel Mount, 0-100 PSI 1
9 122582 16 Refer to: Handpiece Holders AR
17 Knob , Blue (Includes set Screw) 3
a) Control Panel without Scaler
18 1
b) Control Panel with Scaler
19 Air Control Valve 3
20 Screw, Pan Head 2
21 Screw Pan Head, TT ZCBC (.190-24 x .500) 4
Models: All 22 Control Panel Box 1

Serial Numbers: Not Shown - 002-1147-00

V796868 thru V933242 23 Tri-Block Replacement Membrane Repair Kit 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised 4/3/2019] E-6.1 Always verify model & serial number
 Air Control Valve Valve
Assembly includes: 050-7873-00-232 22
Lock
Trim Washer
Nut 040-0010-129 21

053-2163-00 23 1 a) 029-4650-00
b) 029-4993-00
c) 029-5119-00
040-0004-00 20

a) 050-11482-00-232 18 2 041-0006-02
b) 050-11483-00-232 029-2449-03 19
c) 050-11473-00-232 15 AR = as required
Delivery System Components
Item Description Qty.
053-1165-01 17
a) Tri-Block (Models 8000-001 & 8000-003)
1 b) Dual-Block (Models 8000-002 & 8000-004) 1
c) Quad-Block (Model 8000-007)
122841 15 2 Nut #6-32 KEPS W/Starwasher AR
3 050-7616-00-232 3 Bracket (Tri-Block) 1
Handpiece blocks (Facing Front - Left to Right)
a) Fiber Optic (Models 8000-003 & 800-004)
4 a) 029-5122-01 4 (For 8000-007 ONLY 2 required)
b) Manifold Assy, Handpiece
1 EA

b) 029-5122-00 c) Manifold Assy. Scaler

16 c) 029-5122-02
d) Mainfold, Syringe

d) 029-4652-00 5 Block Bracket 1

6 Screw Pan Head (6-32X.375) 2
7 Refer to: Tubing & Fittings AR
5 050-7874-00-232 8 Valve, C.W. Control 1
2 9 Clamp (11/16”) 1
10 Screw (#10-24 x 3/8”) 2
6 040-0006-108
11 Lock Washer 2
12 Screw Pan Head PHL (10-32 x 3/8”) 2
10 040-0010-47
040-0008-06 14 13 Handpiece Holder Assembly
a) Four Position b) Five Position 1
7
12 040-0010-74 14 Screw Mach, Pan Head PHL (8-32 x 1/2) 4
15 Gauge, Panel Mount, 0-100 PSI 1
a) 002-10300-00 13 16
8 117585 16 Refer to: Handpiece Holders AR
b) 029-4994-01 11 P12575 17 Knob , Blue (Includes set Screw) 3
a) Control Panel without Scaler
9 122582 18 b) Control Panel with Scaler 1
c) Control Panel, five position
19 Air Control Valve 3
20 Screw, Pan Head 2
21 Screw Pan Head, TT ZCBC (.190-24 x .500) 4
22 Control Panel Box 1
Models: All 23 Insulator for Scaler (Tightens on with qty 2 of 1
item # 2)
Serial Numbers: V933243 thru V986004 24 Not Shown - 002-1147-00 1
Tri-Block Replacement Membrane Repair Kit

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 4/3/2019] E-6.2 Always verify model & serial number
 Air Control Valve Valve
Assembly includes: 050-7873-00-232 22
Lock
Trim
Nut
Washer 040-0010-129 21

053-2163-00 23 1 a) 029-4650-00
b) 029-4993-00
c) 029-5119-00
040-0004-00 20

a) 050-11482-00-232 18 2 041-0006-02
b) 050-11483-00-232
029-2449-03 19
15 AR = as required
c) 050-11473-00-232
Delivery System Components
Item Description Qty
053-1165-01 17
a) Tri-Block (Models 8000-001, -003, -005, -006 & -008)
1 b) Dual-Block (Models 8000-002 & -004) 1
c) Quad-Block (Model 8000-007)
122841 15 2 Nut #6-32 KEPS W/Starwasher 5
3 050-7616-00-232 3 Bracket (Tri-Block) 1
Handpiece blocks (Facing Front - Left to Right)
a) Fiber Optic (Models 8000-003,-004, -006 & -008)
(For 8000-007 ONLY 2 required) 1 EA
4 a) 029-5122-01 4 b) Manifold Assy, Handpiece
b) 029-5122-00 c) Manifold Assy. Scaler
16 c) 029-5122-02
d) Mainfold, Syringe
5 Block Bracket 1
d) 029-4652-00
6 Screw Pan Head (6-32X.375) 8
7 Refer to: Tubing & Fittings AR
5 050-7874-00-232 8 Valve, C.W. Control 1
2 9 Clamp (11/16”) 1
10 Screw (#10-24 x 3/8”) 2
6 040-0006-108
11 Lock Washer 2
12 Screw Pan Head PHL (10-32 x 3/8”) 2
10 040-0010-47
040-0008-06 14 13 Handpiece Holder Assembly
a) Four Position b) Five Position 1
7
12 040-0010-74 14 Screw Mach, Pan Head PHL (8-32 x 1/2) 4
15 Gauge, Panel Mount, 0-100 PSI 1
a) 002-10300-00 13 16
b) 029-4994-01
8 117585 16 Refer to: Handpiece Holders AR
11 P12575 17 Knob , Blue (Includes set Screw) 3
a) Control Panel without Scaler
9 122582 18 b) Control Panel with Scaler 1
c) Control Panel, five position
19 Air Control Valve 3
20 Screw, Pan Head 2
21 Screw Pan Head, TT ZCBC (.190-24 x .500) 4
22 Control Panel Box 1
Models: All 23 Insulator for Scaler (Tightens on with qty 2 of item # 2) 1
Not Shown - 002-1147-00
Serial Numbers: 24 1
V986005 thru V1043397 Tri-Block Replacement Membrane Repair Kit

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 4/3/2019] E-6.3 Always verify model & serial number
 Air Control Valve Valve
Assembly includes:

050-7873-00-232 25
Lock
Trim Washer
Nut

040-0010-129 24
1 a) 029-4650-00
b) 029-4993-00
053-2163-00 27 c) 029-5119-00

AR = as required
040-0004-00 23
a) 050-11482-00-232 21 Delivery System Components
b) 050-11483-00-232 Item Description Qty.
c) 050-11473-00-232 029-2449-03 22 a) Tri-Block (Models 8000-001 & 8000-003)
1 b) Dual-Block (Models 8000-002 & 8000-004) 1
c) Quad-Block (Model 8000-007)

053-1165-01 20 2 Nut #6-32 KEPS W/Starwasher AR

3 Bracket 1
Handpiece blocks (Facing Front - Left to Right)
014-0666-00 18 2 041-0006-02 a) Fiber Optic (Models 8000-003 & 800-004)
(For 8000-007 ONLY 2 required) 1 EA
4 b) Manifold Assy, Handpiece
c) Manifold Assy. Scaler
3 050-7616-00-232 d) Mainfold, Syringe
5 Block Bracket 1

4 a) 029-5122-01
6 Screw Pan Head (6-32X.375) 8

19 b) 029-5122-00 7 Refer to: Tubing & Fittings AR

8 Valve, C.W. Control 1
c) 029-5122-02
d) 029-4652-00 9 Clamp (11/16”) 1
10 Gauze Sponge 2
11 Exhaust Collector Top Housing 1
5 050-11465-00-216 12 Exhaust Collector Bottom Housing 1
13 Screw (10-24 x 1/2” Pan Head Phillips) 2
6 040-0006-98 14 Lock Washer 2
040-0008-06 17 P12575 14 15 Screw Pan Head PHL (10-32 x 3/8”) 2
Handpiece Holder Assembly
16 1
2 a) Four Position b) Five Position
a) 002-10300-00 16 17 Screw Mach, Pan Head PHL (8-32 x 1/2) 4
b) 029-4994-01 19 7 18 Gauge, Panel Mount, 0-100 PSI 1
19 Refer to: Handpiece Holders AR
121547 10 20 Knob , Blue (Includes set Screw) 3
a) Control Panel without Scaler

15 8 117585 21 b) Control Panel with Scaler 1

040-0010-74 053-1614-00-216 11 c) Control Panel, five position
22 Air Control Valve 3
23 Screw, Pan Head 2
040-0010-129 13 053-1615-00-216 12 9 122582 24 Screw Pan Head, TT ZCBC (.190-24 x .500) 4
25 Control Panel Box 1
Models: All 26 Insulator for Scaler (Tightens on with qty 2 of
item # 2) 2

Serial Numbers: V1043398 thru Present Not Shown - 002-1147-00

24 1
Tri-Block Replacement Membrane Repair Kit

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 4/3/2019] E-6.4 Always verify model & serial number
 4 1 040-0010-144

4 029-4651-00 10

2 050-8078-00-232

3 040-0006-105

4 014-0667-00

6
4 9

5 053-2040-00

11 053-2041-00

6
6
6

7 053-1828-00

Water System Components

Item Description Qty.
VA1297 1 Pan Head Screw (10/32” x 1/2”) 4
9 2 Water Bottle Bracket 1
3 Pan Head Screw (6/32” x 1”) AR
4 Water Regulator Assembly 1
014-0669-00 8 5 Water Bottle Cap 2
6 Refer to: Tubing & Fittings AR
7 Water Bottle (1 Liter) 2
8 Valve Rounting Toggle 1
Models: All 9 Nipple (10/32”) NSS
Serial Numbers: TGC001000Thru TGC001254 10 Hex Plug (10/32”) 2
11 Water Bottle Gasket AR

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 7/26/18] E-7 Always verify model & serial number
 1 041-0006-02

2 040-0008-06

3 050-7621-00-232

4 040-0006-109

016-0888-00 15
5 002-1366-00
13 13
14 7 117481

6 002-1813-00

8 117482
Water System Components
1 Item Description Qty.
16
14 11 053-1828-00
1 Nut (#6/32) 4
2 Pan Head Screw (8/32” x 1/2”) 4
3 Water Bottle Bracket 1
4 Pan Head Screw (6/32” x 1”) AR
014-0176-52 9 5 Water Regulator Assembly Kit 1
*Also includes item # 13, 14 & 16
109714 14 6 Water Bottle Cap Assembly (incl. 7 thru 10) N
12 002-1367-00 7 Barb Fitting (1/16” to 1/16”) 2
8 Barb Fitting (1/8” x 1/8”) 2
117660 13 9 Water Bottle Gasket 2
177524 10 10 Pick-Up Tube 2
VA129701i 11 Water Bottle (1 Liter) 2
Valve Rounting Toggle Kit (w/ relief)
12 1
*Also includes item # 13, 14 & 15
Models: All 13 Gasket (3/16” x 5/16” x 1/32”) 5
Serial Numbers: V796868 thru Present 14 Barb Fitting (10/32” x 1/16”) 5
15 90° Swivel Fitting (#10/32) 2

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 1/11/2019 E-7.1 Always verify model & serial number
 116599 15

1
053-2054-00-216 14

1 040-0010-144

016-0945-03 13
1 2 053-2056-00-216

050-7582-00-232 12

3 053-2053-00-216

Panel Components
Item Description Qty.
054-0597-00 11
1 Pan Head Screw (10/32” x 1/2”) AR
1 2 Right Side Panel 1
053-2055-00-216 10 4 016-1193-00 3 Front Panel 1
4 Caster 2
VA1301
5 Pan Head Screw (6/32” x 1/2”) 4
041-0500-00 9 6 Screen Cover Kit (includes item 5) 1
7 Locking Caster 2

8 5 040-0006-27 8 Lock Washer (1/2”-13) 4

045-0001-33 016-1197-00 7 9 Nut (1/2”-13) 4
002-1228-00 6 10 Left Panel 1
11 Foam, Electrical Compartment 1
12 Removable Panel, Electrical Enclosure 1
Models: All 13 Edge Trim (order by inch - qty 1 = 1”) AR
Serial Numbers: TGC001000 thru TGC001254 14 Top Panel 1
15 Stainless Steel Tray 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 1/24/11] E-8 Always verify model & serial number
 116599 14

1
053-2054-00-216 13
1 040-0010-129

054-0597-00 12
2 053-2056-00-216
1
050-7861-00-232 11

3 053-2053-00-216

053-2055-00-216 10

VA1301-1

Panel Components
1
Item Description Qty.
1 Pan Head Screw (10/32” x 1/2”) AR

041-0500-00 9 4 016-1193-00 2 Right Side Panel 1

3 Front Panel 1
4 Caster 2
016-1197-00 7 5 Pan Head Screw (6/32” x 1/2”) 4
045-0001-33 8 040-0008-79 5 6 Screen Cover Kit (includes item 5) 1
7 Locking Caster 2

002-1228-00 6 8 Lock Washer (1/2”-13) 4

9 Nut (1/2”-13) 4
10 Left Panel 1
11 Removable Panel, Electrical Enclosure 1
Models: All 12 Foam, Electrical Compartment 1
Serial Numbers: V796868 thru V1097496 13 Top Panel 1
14 Stainless Steel Tray 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 8/10/2011] E-8.1 Always verify model & serial number
 116599 14

1
053-2054-00-216 13
1 040-0010-129

054-0597-00 12
2 053-2056-00-216
1
050-7861-00-232 11

3 053-2053-00-216

053-2055-00-216 10
VA1301-1

Panel Components
1
Item Description Qty.
1 Pan Head Screw (10/32” x 1/2”) AR

041-0500-00 9 4 016-1422-00 2 Right Side Panel 1

3 Front Panel 1
4 Caster 2
016-1423-00 7 5 Pan Head Screw (6/32” x 1/2”) 4
045-0001-33 8 040-0008-79 5 6 Screen Cover Kit (includes item 5) 1
7 Locking Caster 2

002-1228-00 6 8 Lock Washer (1/2”-13) 4

9 Nut (1/2”-13) 4
10 Left Panel 1
11 Removable Panel, Electrical Enclosure 1
Models: All 12 Foam, Electrical Compartment 1
Serial Numbers: V1097497 thru Present 13 Top Panel 1
14 Stainless Steel Tray 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 3/13/12] E-8.2 Always verify model & serial number
 15 a) 053-2051-01 16 053-2052-00 20 040-0010-154
b) 053-2051-00
17 050-7632-00-232
21
137258 14 040-0010-146

18 016-0447-01 22 002-1297-00
051-1217-00-232 13
13
23 015-0371-00
040-0010-144 12 19 040-0010-74

7 24 041-0010-14

050-7636-00-232 11 1 042-0081-08

040-0008-06 10 Frame and Back Components

Item Description Qty.

002-1285-00 9 5 1 Bolt (1 1/4” x 1/4”) 2

2 Frame 1
3 Snap Bushing (1/2” Dia) 4
050-7634-00-232 8 Installation
a) Front & Back Side Mounts (1 EA)
4 b) Left & Right Side Mounts (2 EA) AR
c) Upper Mount (1 EA)
d) Lower Mount (1EA)
5 Kep Nut (10/32”) 6
040-0010-144 7 6 Compressor Cover 1
7 Pan Head Screw (10/32”) 2
8 Electrical Cover 1
Back Door Kit
9 1
050-7635-00-232 6 Includes items #18, #19, #5, and #10
10 Screw, Panhead (8-32X1/2) 3
77009189 5 11 Bracket 1
12 Screw (.190 x 32 x 1/2”) 2
13 Back Handle 1
14 Quick Disconnect Assembly 2

a) 054-0592-00 4 VA1273
15 a) Red Washer
b) Blue Washer 1 EA
b) 054-0593-00 16 QD spacer 2
c) 054-0594-00 030-1821-00-232 2 17 Panel, Top back Cover 1
d) 054-0595-00 18 Knob 1

053-0068-15 3 19 Pan Head Screw (10/32” x 3/8”) 1

20 Screw (.190 x 32 x .437) 2
21 Screw (.190 x 32 x .75) 1
22 Magnet Kit. 1
Models: All 23 Cable Clamp 1
24 Magnet kit 1
Serial Numbers: TGC00100 Thru TGC001254 Not Shown - 015-1338-02
25 1
Power Supply Cord

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 2/1/2018 E-9 Always verify model & serial number
 1 040-0008-01
052-0707-00-232 19
2 137258
14
053-2208-00 18
3 a) 053-2051-01 4 040-0008-43
b) 053-2051-00
5 002-1297-00

14

050-7636-00-232 17 10 6 015-0371-00

7 77009189
040-0008-06 16

030-1827-00-232 15 8

040-0010-129 14

050-7863-00-232 13
Frame and Back Components
Item Description Qty.
050-7858-00-232 12 1 Screw, Panhead ( 0.164 X 0.75) 2
2 Coupling, FEM QD 1
a) Red Washer
3 1 EA
040-0010-47 11 b) Blue Washer
4 Screw, Flat Head (8-32 x 3/4”) 3
5 Flat Mounting Magnet (M4 X .7) 1
77009189 10 6 Drain Valve Hose Clip 1
7 Nut (M4) 1
VA1273-2
8 Frame, Weldment for Dental Cart NSS
Insulation
a) Front & Back Side Mounts (1 EA)
9 b) Left & Right Side Mounts (2 EA) AR
c) Upper Mount (1 EA)
a) 054-0592-00 9 d) Lower Mount (1EA)
b) 054-0593-00 10 Locknut (8-32) 9
c) 054-0594-00 11 Screw, Panhead (#10-24 X 3/8”) 6
d) 054-0595-00 12 Electrical Cover Panel 1
13 Panel, Top Back Cover 1
14 Screw, Panhead (.190” x 1/2”) 10
15 Back Door Weldment 1
16 Screw, Panhead (#8-32 x 1/2”) 3
Models: All 17 Cord Bracket 1
Serial Numbers: V796868 thru V871908 18 Door Handle 1
19 Handle 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 7/26/18] E-9.1 Always verify model & serial number
 052-0707-00-232 18

053-2208-00 17 1 040-0008-01
13
3 a) 053-2051-01
2 137258
b) 053-2051-00

13 4 050-7863-00-232

5 016-1313-00
050-7636-00-232 16
10 2 6 015-0371-00

040-0008-06 15 7 041-0026-04

030-1827-00-232 14
8
040-0010-129 13

050-7858-00-232 12 Frame and Back Components

Item Description Qty.
1 Screw, Panhead ( 0.164 X 0.75) 2
040-0010-47 11 2 Coupling, FEM QD 1
a) Red Washer
3 1 EA
b) Blue Washe
4 Panel, Top Back Cover 1
77009189 10 5 Flat Mounting Magnet (M4 X .7) 1
6 Drain Valve Hose Clip 1
VA1273-4
7 Nut (M4) 1
8 Frame, Weldment for Dental Cart NSS
Insulation
a) Front & Back Side Mounts (1 EA)
a) 054-0592-00 9 9 b) Left & Right Side Mounts (2 EA)
c) Upper Mount (1 EA)
AR

b) 054-0593-00 d) Lower Mount (1EA)

c) 054-0594-00 10 Locknut (8-32) 6
d) 054-0595-00 11 Screw, Panhead (#10-24 X 3/8”) 6
12 Electrical Cover Panel 1
13 Screw, Panhead (.190” x 1/2”) 10
14 Back Door Weldment 1
15 Screw, Panhead (#8-32 x 1/2”) 3
Models: All 16 Cord Bracket 1
Serial Numbers: V871909 thru V933242 17 Door Handle 1
18 Handle 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 7/26/18] E-9.2 Always verify model & serial number
 052-0707-00-232 18

12 1 040-0008-01

053-2208-00 17 3 a) 053-2051-01
b) 053-2051-00
2 137258

4 016-1313-00
14

050-7636-00-232 16 2 5 041-0026-04

015-0371-00 15 6 030-1885-00-232

040-0008-06 14

030-1827-00-232 13
Frame and Back Components
040-0010-129 12 Item Description Qty.
1 Screw, Panhead ( 0.164 X 0.75) 2
2 Coupling, FEM QD 2
050-7863-00-232 11 a) Red Washer
3 1 EA
b) Blue Washe
15
050-7945-00-232 10 4 Flat Mounting Magnet (M4 X .7) 1
5 Nut (M4) 1
6 Frame, Weldment for Dental Cart 1
040-0010-129 9 VA1273-3
Insulation
a) Front & Back Side Mounts (1 EA)
7 b) Left & Right Side Mounts (2 EA) AR
c) Upper Mount (1 EA)
d) Lower Mount (1EA)
8 8 Locknut (8-32) NSS
9 Screw (10-24 x 1/2” Pan Head Phillips) 6
a) 054-0592-00 7 10 Electrical Cover Panel 1
b) 054-0593-00 11 Panel, Top Back Cover 1
c) 054-0594-00 12 Screw, Panhead (.190” x 1/2”) 10
d) 054-0595-00 13 Back Door Weldment 1
14 Screw, Panhead (#8-32 x 1/2”) 5
15 Tubing Clamp 3
Models: All 16 Cord Bracket 1
Serial Numbers: V933243 thru Present 17 Door Handle 1
18 Handle 1

© Midmark Corporation 2008 SF-1925 004-0586-00 [Revised: 7/26/18] E-9.3 Always verify model & serial number
 014-0775-00 1 117349 2 014-0709-00 3 029-4999-00 13 014-0526-00 16 117477 18

014-0707-00 19
4 014-0730-00 17
117351 117479 5 117480 6 016-0888-00 14

Tubing and Fittings

053-2677-00 7 117698 8 a) S059-00120 9 Item Description Qty.
b) 002-1368-00 014-0687-00 15 1 Connector (#8-32 to 1/8” O.D. Tube) AR
c) 053-1709-00 2 Connector (#10-32 to 1/4” O.D. Tube) AR
3 Barb Tee Fitting AR
4 Brass Plug (#10-32 Threads) AR
5 Uni-Clamp (1/8” O.D. Tube) AR
6 Sleeve Clamp (1/4”O.D. Tube) AR
7 Sealing Gasket AR
a) 177531 11 8 Check Valve (1/8” O.D. Tube) AR
a) 177524 10 b) 177523 Tubing
b) 014-0650-01 c) 177529 9 a) 2- Hole (Syringe Hose) AR
c) 275263 d) 177532 014-0693-00 12 b) 4- Hole Handpiece Tubing Kit
c) Foot Control (Shown)
Tubing (1/8” ID x 1/4” OD)
a) Blue
10 AR
b) Red
c) Yellow
Tubing (1/8” OD)
a) Red Tubing (.159” ID)
11 b) Blue Tubing (1/8” ID) AR
c) Clear Tubing (1/8” ID)
d) Orange Tubing (.159” ID)
VA127201i 12 Blue Tubing (3/8” I.D.) AR
13 Block Cross Assembly AR
Note 14 90 Degree Swivel Fitting (#10-32) AR
All tubing must be ordered by the foot. Therefore, the quantity ordered is the amount of feet of tubing needed. 15 Barb Tee Fitting (1/8” x 1/16” x 1/16”) AR
Example: ordering an quantity of 2 would be ordering two feet of tubing. 16 Barb Fitting (5/32, 3/16) AR
17 Fitting AR

18 Fitting AR
Models: All
19 Tee, (10-32 X 1/16” BARB X 1/16” BARB) AR
Serial Numbers: all Not Shown - 057-0734-00
20 AR
Handpiece Nut (sleeve) 4 Port (pass)

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 2/1/2018] E-10 Always verify model & serial number
*AR = As Required
 Note
2 a) 002-10310-00
3 002-10308-00
DP #’ s are Parts Warehouse part numbers.
b) 002-10310-01

4 002-10309-00

5 DP# R-F1200-3B

6 DP# R-F1200-3C

7 DP# R-F12100-3A

1/8 1/8 OR
GN 5/16"
Clear 8
002-1161-00 1 5/16"
Clear
w/ Dash 1/8
BN 18 9 DP# P-1898
Specify Length
When Ordering
10 DP# 0-2008.1
Foot Control Assembly
11 DP# R-F1200-3D Item Description Qty.
1 Foot Control Assembly (Includes Items 2 thru 18) 1
2a Valve Housigng Kit (3- port:) 1
b Valve Housigng Kit (with chip air)
12 DP# O-2012.1 3 Dome Kit 1
4 Dome Retaining Ring Kit 1
5 Spring, Dome 1
6 Valve Stem 1
17 7 Spring, Conical 1
8 Valve 1
9 Barb Fitting (3/16”) 2

DP# RF1081 16 10 O-Ring Kit 2

11 Cartridge, Valve Stem 2
13 DP# R-F1024 12 O-ring 1
DP# RF1025 15 13 Screw (#6 x 1/2”) 4

DP# R-F1200-5 14 14 Foot, Rubber 5

15 Screw (#4-40 x 5/16”) 2
16 Screw (#4 x 1/2”) 4
Models: All 17 Base Plate 1

Serial Numbers: 18 Foot Control Tubing, Refer to: Tubing & Fittings AR
Vxx-Vxxx
*AR = As Required

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 06/28/18] E-11 Always verify model & serial number
 Note
2 a) 002-10310-00
3 002-10308-00
DP #’ s are Parts Warehouse part numbers.
b) 002-10310-01

002-10367-00 19

4 002-10309-00

5 DP# R-F1200-3B

6 DP# R-F1200-3C

7 DP# R-F12100-3A

1/8 1/8 OR
GN 5/16"
Clear 8
002-1161-00 1 5/16"
Clear
w/ Dash 1/8
BN 18 9 DP# P-1898
Specify Length
When Ordering Foot Control Assembly
10 DP# 0-2008.1
Item Description Qty.
1 Foot Control Assembly (Includes Items 2 thru 19) 1
11 DP# R-F1200-3D
2a Valve Housigng Kit (3- port:) 1
b Valve Housigng Kit (with chip air)
3 Dome Kit 1

12 DP# O-2012.1 4 Dome Retaining Ring Kit 1

5 Spring, Dome 1
6 Valve Stem 1
7 Spring, Conical 1

17 8 Valve 1
9 Barb Fitting (3/16”) 2
10 O-Ring Kit 2
11 Cartridge, Valve Stem 2
DP# RF1081 16 12 O-ring 1
13 DP# R-F1024 13 Screw (#6 x 1/2”) 4
DP# RF1025 15 14 Foot, Rubber 5
15 Screw (#4-40 x 5/16”) 2
DP# R-F1200-5 14 16 Screw (#4 x 1/2”) 4
17 Base Plate 1
Models: All 18 Foot Control Tubing, Refer to: Tubing & Fittings AR
19 Strain Relief Kit (Mounted on Vetpro unit) 1
Serial Numbers: Vxxx - present
*AR = As Required

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 06/28/18] E-11.1 Always verify model & serial number
Athena Brand Handpieces
002-1156-00 1 6 002-1157-00
002-1155-00 5

8 a) 016-1204-00
b) 016-1204-01
c) 016-1204-02
a b c

002-1159-00 2 9 a) 016-1204-03
b) 016-1204-04
c) 016-1204-05
a b c Athena Handpieces & Maintenance
Item Description Qty.
7 002-1158-00 1 Low Speed Handpiece 1
2 Prophy Angle 1
10 a) 016-1204-06 3 Prophy Cups (pack of 144) 1
002-1160-01 3 b) 016-1204-07 Disposable Prophy Angle with Cup:
4 a) 10 pack 1
b) 100 per box
a b 5 High Speed Handpiece 1

6 Fiber Optic High Speed Handpiece 1

Reference: Fiber Optic Components
7 Bur Block Kit (Including all Burs, 1 ea) 8
11 a) 016-1204-08 a) Round # 2 (Bur)
b) 016-1204-09 8 b) Round # 4 (Bur) 5 ea
a) 002-1279-00 4 c) Round # 6 (Bur)
b) 002-1279-02 a) Taper Fissure Crosscut # 701
9 b) Taper Fissure Crosscut # 701L 5 ea
c) Inverted Cone # 36
a b 10 a) Straight Fissure Crosscut # 558 5 ea
b) Straight Fissure Crosscut # 558L
a) Diamond Torpedo, Fine, #869LF
11 5 Ea
b) Diamond Football, Fine, #831F
Models: All Items # 12 and # 13 are not shown
064-0031-00
Serial Numbers: Up to V871908 12 Handpiece Oil 1/4 fl. oz.

© Midmark Corporation 2008 SF-1930 004-0586-00 [Revised: 6/14/16]

E-12 Always verify model & serial number
Midmark Brand Handpieces & Parts 20 016-1309-00
016-1310-00 17
002-1277-00 1
2 a) 002-1279-00
5 002-1275-00
b) 002-1279-02

016-1362-00 18
3 002-1160-01

4 002-1159-00 002-1276-00 6 016-1312-00 19 21 016-1311-00

Midmark Brand Handpieces & Parts

Item Description Qty.
8 002-1994-00 12 016-1308-00 1 Lowspeed Instrument 1
Disposable Prophy Angle with Cup:
2 a) 10 pack 1
b) 100 per box
3 Prophy Cups (pack of 144) 1
4 Prophy Angle 1
13 002-10025-00 5 Highspeed Instrument 1

6 Fiber Optic Instrument 1

Reference: Fiber Optic Components
Kit, Handpiece and Coupler, High speed FO
7 1
swivel (Includes items 8 thru 11)
10 016-1728-00 8 Kit, handpiece, High speed FO Swivel 1
14 002-1293-00 9 Kit, Coupler, High Speed FO Swivel 1
10 Wrench, Swivel Coupler 1
7 002-1996-00 11 Conditioner Nozzle, Swivel Handpiece 1
5-Hole Replacement Gasket (used on items
12 1
1, 5, 6 & 7)
15 002-1294-00 13 Turbine *Includes chuck and item # 20 1
14 Chuck *Includes items # 20 & # 21 1
15 Head Cap * Includes items # 17 & # 20 1
11 016-1729-00
Lowspeed Swivel Adapter * Includes items
16 1
# 12 and #18
16 002-1291-00
17 Head O-Ring 1
18 O-Ring, Swivel Adapter 1

9 002-1995-00 19 Wave Spring 2

20 Head Cap Wrench 1
21 Spindle Cleaning Tool 1
VA1608
Items 22 thru 25 Not Shown
22 002-1295-00 Water Spray Tool 1
Models: 8000-001, -002, -004, -005, -007 8000-003, -006, -008 8000-006s, -007s, -008s 23 002-1432-00 Handpiece Conditioner 1
24 053-2259-00 Conditioner Tube 3
Serial Numbers: V871909 thru Present V871909 thru V1852894 V871909 thru V1878359 25 016-1731-00 Kit, O-ring, Swivel Coupler 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/24/17] E-13 Always verify model & serial number
Midmark Brand Handpieces & Parts
002-1277-00 1
2 a) 002-1279-00 016-1310-00 15 18 016-1309-00
b) 002-1279-02

016-1362-00 16
3 002-1160-01

016-1312-00 17

4 002-1159-00 5 002-10021-00

7 002-10022-00
11 016-1308-00
Midmark Brand Handpieces & Parts
Item Description Qty.
1 Lowspeed Instrument 1
Disposable Prophy Angle with Cup:
2 a) 10 pack 1
12 002-10025-00 b) 100 per box
3 Prophy Cups (pack of 144) 1
4 Prophy Angle 1

5 Fiber Optic Instrument 1

Reference: Fiber Optic Components
9 016-1728-00 6 Kit, Handpiece and Coupler, High speed FO 1
swivel (Includes items 7 thru 10)
7 Kit, handpiece, High speed FO Swivel 1
8 Kit, Coupler, High Speed FO Swivel 1
6 002-10023-00
13 002-10024-00 9 Wrench, Swivel Coupler 1
10 Conditioner Nozzle, Swivel Handpiece 1
5-Hole Replacement Gasket (used on items
11 1
1, 5 & 6)
Turbine Cartridge Kit *Includes chuck and
14 002-1291-00 12 item # 18 1

10 016-1729-00 13 Head Cap * Includes items # 15 & # 18 1

Lowspeed Swivel Adapter * Includes items
14 1
# 11 and #16
15 O-Ring 1

8 002-1995-00 16 O-Ring 1
VA1608-3i 17 Wave Spring 2
18 Head Cap Wrench 1
Items 19 thru 22 Not Shown
19 002-1295-00 Water Spray Tool 1
Models: 8000-003, -006, -008 8000-006s, -007s, -008s 20 002-1432-00 Handpiece Conditioner 1
21 053-2259-00 Conditioner Tube 3
Serial Numbers: V1852895 thru Present V1878360 thru Present 22 016-1731-00 Kit, O-ring, Swivel Coupler 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 5/24/17] E-13.1 Always verify model & serial number
Midmark Brand Handpieces & Parts

2 a) 016-1204-00
b) 016-1204-01
c) 016-1204-02
a b c

3 a) 016-1204-03
b) 016-1204-04
c) 016-1204-05

a b c

1 002-1158-00

4 a) 016-1204-06
b) 016-1204-07

a b

5 a) 016-1204-08
b) 016-1204-09
Midmark Brand Handpieces & Parts
Item Description Qty.
1 Bur Block Kit (Including all Burs, 1 ea) 8
a) Round # 2 (Bur)
2 b) Round # 4 (Bur) 5 ea
c) Round # 6 (Bur)
a b a) Taper Fissure Crosscut # 701
3 b) Taper Fissure Crosscut # 701L 5 ea
c) Inverted Cone # 36
a) Straight Fissure Crosscut # 558
4 5 ea
Models: All b) Straight Fissure Crosscut # 558L
a) Diamond Torpedo, Fine, #869LF
5 5 Ea
Serial Numbers: V871909 thru Present b) Diamond Football, Fine, #831F

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 4/19/16] E-14 Always verify model & serial number
 2 120514
1 120795
3 016-1029-00

4 016-0991-00

5 016-0991-04

3 6 016-1032-00
016-0989-00 18
7 152055

016-1030-00 17

8 120903

9 016-0991-01
Syringe
10 016-0990-00 Item Description Qty.
117660 16 1 Standard Syringe (Includes Items 1-18) 1
2 • Syringe Tip 1
11 016-0991-03 3 • Tip adapter Assembly (DCI# 3065) 1
DCI# 0084 15 4 • O-Ring (DCI# 2255) (pkg of 12) 2
5 • O-Ring (DCI# 2202) (pkg of 12) 2
12 016-0988-00 6 • Spring, Syringe Button (DCI# 9670) 1
7 •Button Cartridge Kit (Includes 8 thru 12 not 11) 1

016-1031-00 14 8 •• Button Valve 2

9 •• O-Ring (DCI# 2203) (pkg of 12) 2
13 016-0991-02
10 •• Retaining Ring (DCI# 9601) 2
11 O-Ring (DCI# 2212) (pkg of 12) 2
12 •• Pin (DCI# 9648) 1
13 O-Ring (DCI# 2211) (pkg of 12) 2
14 Syringe Handle (DCI# 3491) 1
15 Barb Fitting (DCI# 0084) (pkg of 10) 2
Models: All (Syringe) 16 Gasket Sealing 2
17 Pin, Tip Adapter (DCI# 9659) 1
Serial Numbers: all
18 Spring, Tip Adapter with Body (DCI# 9677) 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 10/13/16] E-15 Always verify model & serial number
 016-1203-04 4
016-1718-01 5

3 a) 016-1203-00
b) 016-1203-03
016-1379-00 6

2 a) 016-1218-00
b) 016-1375-00
9
10
1 Scaler
7
8 2

016-1380-00 7
6 5 4
3
Item Description Qty.
Satelec Scaler Kit
a) with Tips & Power Supply
(Includes items 2 thru 9)
1 Reference: Scaler Components 1
b) with Tips, Power Supply and LED light
(-006 thru -008 Models Only)
(Includes items 2 thru 10)
Reference: LED Scaler Components
• Handpiece
016-1376-00 10 2 a) Standard 1
1 a) 002-1002-02 b) LED
b) 002-1002-05 • Scaling Tip
3 a) Universal (Tip No. 1) 1
a) 002-1498-00 8 b) Voluminous Calculus (Tip No. 2)
b) 002-1499-00 4 • Scaling Tip, Shallow Pockets (Tip No. 10P) 1
5 • Scaler Tip Wrench 3
6 • Potentiometer 1
a) 016-1378-00 9 7 • Scaler Knob 1
b) 016-1382-00 8 • Scaler Tubing a) (Std) b) (LED) 1
9 • Scaler Control Modular a) (Std) b) (LED 1
10 • LED Light (-007, -008 Models) 1
11 Air Switch (N.O.) 1
Items # 12 thru # 18 are Not Shown
120769 11 12 • 002-1238-00 - Scaler Tips, Ultrasonic, Vet 1
(Includes items 13 thru 15)
•• 016-1203-05 - Ultrasonic Stones, Dog Probe
13 1
VA1722-1i Short
14 •• 016-1203-06 - Ultrasonic Stones, Cat Probe 1

•• 016-1203-07 - Ultrasonic Stones, Dog Probe

15 1
Long

Models: Only 8000-001, -003, -005, -006, -007, -008 (Scaler) 16 016-1502-00 - EMI Supression Core-ACTEON
Scaler 1

17 016-1717-00 - ACTEON Autoclavable Tip Box 1

Serial Numbers: V2200 thru V1271515
18 016-1589-00 - Tip Wear Guide 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 9/25/15] E-16 Always verify model & serial number
 016-1203-04 4
016-1718-01 5

3 a) 016-1203-00
b) 016-1203-03
016-1379-00 6

2 a) 016-1218-00
b) 016-1375-00
10
9 1

7 Scaler
8 2

016-1380-00
7 3
6 5 4

Item Description Qty.

Satelec Scaler Kit
a) with Tips & Power Supply
(Includes items 2 thru 9)
1 Reference: Scaler Components 1
b) with Tips, Power Supply and LED light
(-006 thru -008 Models Only)
016-1376-00 10 (Includes items 2 thru 10)
Reference: LED Scaler Components
• Handpiece
a) 002-1498-00 8 1 a) 002-1002-02 2 a) Standard 1
b) 002-1002-05 b) LED
b) 002-1499-00 • Scaling Tip
3 a) Universal (Tip No. 1) 1
b) Voluminous Calculus (Tip No. 2)
4 • Scaling Tip, Shallow Pockets (Tip No. 10P) 1

a) 016-1378-00 9 5 • Scaler Tip Wrench 3

b) 016-1382-00 6 • Potentiometer 1
7 • Scaler Knob 1
8 • Scaler Tubing a) (Std) b) (LED) 1
9 • Scaler Control Modular a) (Std) b) (LED 1
10 • LED Light (-006 thru -008 Models) 1
11 Air Switch (N.O.) 1

120769 11 Items # 12 thru # 17 are Not Shown

E-15.1 12 • 002-1238-00 - Scaler Tips, Ultrasonic, Vet
(Includes items 13 thru 15) 1
VA1722-1i
•• 016-1203-05 - Ultrasonic Stones, Dog Probe
13 1
Short
14 •• 016-1203-06 - Ultrasonic Stones, Cat Probe 1

•• 016-1203-07 - Ultrasonic Stones, Dog Probe

15 1
Long
Models: Only 8000-001, -003, -005, -006, -007, -008 (Scaler)
016-1502-00 - EMI Supression Core-ACTEON
16 1
Scaler
Serial Numbers: V1271516 thru Present
17 016-1717-00 - ACTEON Autoclavable Tip Box 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 9/25/15] E-16.1 Always verify model & serial number
 1 015-2512-00

3 015-2513-00

4 015-2511-00

Fiber Optic Components

Item Description Qty.
002-1237-00 Includes items # 1 thru 5
1 •Power Pack 1

Models: Only 8000-003 & 8000-004 2 •Shadow 5-Hole Tubing 014-0681-00-341 (Does
not include item 3) Not Shown 1

Serial Numbers: 3 •Bulb (Not included with item 2) 1

Start Production thru V933242
4 •Power Supply 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 7/19/11] E-17 Always verify model & serial number
 1 015-1480-00

5 015-2707-00

4 015-2653-00

3 120722

6 015-2708-00

Fiber Optic Components

Item Description Qty.
1 Optic Controller 1
Not Shown - 120721-01
2 1
Tubing 4-Hole Non-Swivel
3 Bulb 1

Models: Only 8000-003, -004, -006, 006S, -007, 007S, -008, -008S 4 Power Supply 1
Blade Adapter (N. America - Models 8000-003,
5 1
Serial
Serial Numbers:
Numbers: -004, -007, -008
V933243 thru Present
6 Blace Adapter (European - Model 8000-006) 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/7/15] E-17.1 Always verify model & serial number
Athena Handpiece Replacement Parts
1 016-1267-01 2 016-1267-00

3 016-1267-02

4 016-1267-06
5 a) 016-1267-03
b) 016-1267-04

6 016-1267-05
Athena Handpiece Replacement Parts
Item Description Qty.
1 4-Hole Gasket 1
2 5-Hole Gasket 1
3 2-Hole Gasket for Little Pro 1
4 Standard & mini head push button cap wrench
Push Button Canister:
5 a) Standard Head without Cap (Fiber Optics only) 1
b) Mini Head without Cap (Non-Fiber Optics only)
6 Standard & mini head push button head cap
Items # 7 thru # 11 are not shown
002-1238-00 - Scaler Tips, Ultrasonic, Vet
7 1 kit
(Includes items 8 thru 10)
• 016-1203-05 - Ultrasonic Stones, Dog Probe
8 1
Models: All Short
9 • 016-1203-06 - Ultrasonic Stones, Cat Probe 1
Serial Numbers: all 10 • 016-1203-07 - Ultrasonic Stones, Dog Probe 1
Long

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 1/20/10] E-18 Always verify model & serial number
 2

053-1274-00 2
8 053-1077-00

9 120910

3
002-0684-02 7
120908 3
10 P11836

1 002-0684-01
11 053-1275-00

053-1275-01 4
6

5
042-0168-03 5
VA1583

12 057-0536-00
120913 6 Handpiece Holders
Item Description Qty.
Syringe Holder Assembly without Sot
1 (Includes items 2 thru 6)
2 • Top Housing Instrument Holder 1
3 • Pad, Instrument Holder 2
4 • Bottom Housing Without Slot 1
5 • Screw, ( MTC K3.5-1.57X20 ATF PT ZN) 4
6 • Set Screw (10-32 x 1/2”) 2
Handpiece Holder Assembly with Slot
7 (Includes items 2, 3, 5, 6, and 8 thru 12)
8 • Lever 1
9 • 3-Way Valve (Normallly Closed) 1
Models: All 10 • Set Screw (6-32 x 1/4”) 1

Serial Numbers: 11 • Bottom Housing With Slot 1

V796868 thru Present
12 • Pivot Pin 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 1/30/19] E-19 Always verify model & serial number
 5

121533 1

a) 015-0083-02 2
b) 015-1294-00
VA1650

a) 015-2586-00 4
b) 015-2665-00

040-0006-27 5 Fiber Optic Electrical Components

Item Description Qty.

7 040-0010-129 1 LG Box 1
Receptacle
2 a) Domestic Models
015-2666-00 3 b) Export Models (-005 & -006)
3 Metal Plate (Export Models Only, -005 & -006)
050-8004-00-232 6 Outlet Cover
a) Domestic Models
4 1
Wall Plate Frame
b) Export Models (-005 & -006)
Models: 8000-005 8000-006 & -006S 5 Screw (6-32 x 1/2”) 1
Serial Numbers: All All 6 Power Supply Retainer 1
7 Screw (10-24 x 1/2” Pan Head Phillips) 6

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/7/14] E-20 Always verify model & serial number
 016-1550-00 1

2 016-1546-00

3 016-1547-00

4 016-1548-00

5 016-1549-00

Scaler Components
Item Description Qty.
1 O-Ring Kit 1
2 Nose 1
Models: 8000-001, -003, -005 8000-006 3 O-Ring (9.9 X 0.75) 1
Serial Numbers: All V2200 tthru V1271515 4 Body 1
5 O-Ring (12.5 X 1.5) 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 1/3/13] E-21 Always verify model & serial number
 2 016-1549-00

016-1550-00 1
3 016-1554-00

4 016-1376-00

5 016-1552-00

5 016-1551-00

LED Scaler Components

Item Description Qty.
1 O-Ring Kit 1
2 O-Ring (12.5 X 1.5) 1
3 O-Ring (16 x 1) 1
Models: 8000-006 & -006S 8000-007, -007S, -008, -008S 4 LED Light Ring 1
Serial Numbers: V1271516 thru Present All 5 LED Focus Light Guide 1
6 Nose 1

© Midmark Corporation 2008 SF-1928 004-0586-00 [Revised: 11/7/15 E-22 Always verify model & serial number
 SUBJECT TO CHANGE WITHOUT NOTICE

Midmark Corporation
60 Vista Drive
Versailles, OH 45380 USA
1-800-643-6275
1-937-526-3662
www.midmark.com