PH700 Benchtop pH Meter

Instruction Manual

APERA INSTRUMENTS (Europe) GmbH

www.aperainst.de
Manual Version 3.2
Table of Contents

1 Brief Introduction ............................................................................................................ - 1 -

1.1 Main Features ...................................................................................................................... - 1 -
2 Technical Specifications.................................................................................................... - 1 -
3 What’s in the Box? ........................................................................................................... - 2 -
4 Instrument Description .................................................................................................... - 2 -
4.1 LCD Display .......................................................................................................................... - 2 -
4.2 Keypad ................................................................................................................................ - 3 -
4.3 Connectors .......................................................................................................................... - 4 -
4.4 Stable reading display mode ................................................................................................. - 4 -
4.5 Data storage, recall, and deletion ......................................................................................... - 4 -
4.6 Max/Min Function ............................................................................................................... - 5 -
5 pH Measurement ............................................................................................................. - 5 -
5.1 Preparation .......................................................................................................................... - 5 -
5.2 pH Electrode Information ..................................................................................................... - 5 -
5.3 Information regarding Calibration ......................................................................................... - 6 -
5.4 pH Meter Calibration ............................................................................................................ - 8 -
5.5 Measuring pH ...................................................................................................................... - 9 -
5.6 Parameter Setting .............................................................................................................. - 11 -
5.7 pH Electrode’s Maintenance ............................................................................................... - 12 -
6 mV measurement .......................................................................................................... - 13 -
6.1 ORP measurement ............................................................................................................. - 13 -
6.2 Notes on ORP measurement............................................................................................... - 13 -
7 Recommended pH Electrodes for Specific Applications ................................................... - 14 -
8 Warranty ....................................................................................................................... - 14 -
1 Brief Introduction

Thank you for purchasing Apera Instruments PH700 Benchtop pH meter.

This instrument is an outstanding combination of advanced electronics design and sensor technology. It’s the
most economical choice of a reliable lab-grade benchtop pH meter. Please read this maual carefully to
properly use and maintain the meter. Apera Instruments reserves the right to update the contents of this
manual without giving prior notices.

1.1 Main Features

• The meter has a built-in microprocessor chip, which enables intelligent functions such as automatic
calibration, automatic temperature compensation, data storage, parameter setup, max/min reading
display, etc.
• The advanced automatic calibration mode has calibration guide and self-diganosis functions,
automatically recognizing standard buffer solutions (USA or NIST series).
• The advanced digital processing technology intelligently improves the meter’s response time and
measuring accuracy with stable reading display mode available.
• The kit comes with a 3-in-1 combination pH Electrode, measuring pH and temperature simultaneously.
• IP54 dustproof and spillproof. Connectors are protected by silicone seal caps, effectively ensuring the
reliability and service life of the meter under harsh environment.
• Detachable electrode holder and 3 bottles of pH buffer solutions come with the kit for convenient use.

2 Technical Specifications

Range 0 to 14.00 pH
Resolution 0.01/0.1 pH
Accuracy ±0.01 pH ±1 digit
pH
Temperature
0 to 100 ˚C (Auto or Manual)
Compensation
Calibration 1 to 3 points automatic calibration
Range ±1999 mV
mV Resolution 1 mV
Accuracy ±0.1% F.S ±1 digit
Range 0 to 100˚C; 32 to 212°F

Temp. Resolution 0.1˚C; 0.1/1°F

Accuracy ±0.5˚C ±1 digit

Data Storage 50 groups

Numberings, Measurement, Unit, Temperature, Temperature
Storage Content
Compensation Status
Others Power DC9V/300mA

IP Ratings IP54 dustproof and spillproof

Size and Dimension (240*235*103) mm/1kg

-1-
3 What’s in the Box?

Content Quantity
3.1 PH700 Benchtop pH Meter 1
3.2 201T-F Plastic 3-in-1 Combination pH Electrode 1
3.3 pH standard buffer solutions (4.00/7.00/10.01 pH) 1 for each 50ml
3.4 9V Power Adapter 1
3.5 Electrode Holder 1 set
3.6 Instruction Manual 1

4 Instrument Description

4.1 LCD Display

Figure-1

(1) — Measurement value

(2) — Calibration icons and numberings

(3) — Measurement unit

(4) — Temperature and reminder icons

(5) — The pH unit displayed during calibration

(6) — The pH value displayed during calibration, numberings for storage and recall, and reminder icons

(7) — Icons for data storage and recall — M+: store measuring data; RM: Recall measuring data

(8) — Self-Diagnosis icons and numberings

(9) — Temperature compensation mode icons:

ATC: Auto Temperature Compensation;

MTC: Manual Temperature Compensation

(10) — Completed calibration icons

(11) — Stable reading icon

(12) — Icons for maximum and minimum values

-2-
4.2 Keypad

Figure-2
3.2.1. Keypad operations

Short press ----- <1.5 seconds; Long press ----- >1.5 seconds.

3.2.2 For keypad operation, please see Table-1.

Table – 1 Keypad operations and descriptions

Keypad Operation Functions

Short Press • Power on/off

Short Press • Select measuring mode: pH→mV.

Long Press • Enter parameter setting：P1→P2→…P4.

• Enter Calibration mode

Short Press
• Cancel any operation and go back to measurement mode

Short Press • In calibration mode, press to conduct calibration

• In parameter setting, press to confirm selection

Short Press • Store measuring data

Long Press • Recall stored measuring data

• In manual temperature compensation mode, short press to change

Short Press temperature, long press to change quickly
or • In parameter setting mode, short press to change parameter and settings.
Long Press • In recall mode, short press to change numberings, long press to change
quickly.

Short Press • Buttons for max/min values (refere to section 3.6)

-3-
4.3 Connectors

Symbol Connector Name Connector Type

REF Socket for reference electrode Φ2 banana type

pH/mV Socket for pH and ORP electrode BNC

TEMP Socket for temperature sensor RCA

DC9V DC9V power socket Φ2.5 direct type

4.4 Stable reading display mode

When the measuring value is stable, smiley face icon appears on LCD,
see Figure-3. Please do not get the reading value or make calibration until the

icon appears and stays.

Figure - 3

4.5 Data storage, recall, and deletion

Storage
When the measurement is stable, press key, the meter displays
M+ icon and storage numberings on LCD, and stores the measuring data.
In Figure-4, the meter stores the first group of the measuring data. Press
again to keep storing.
Figure - 4

Recall stored data

In the measurement mode, long press key to recall the last stored
Measuring data. The meter displays RM icon and storage numberings.
In Figure-5, the meter is recalling the 28th stored measuring data.
Keep pressing and to recall the stored
measuring data successively. Press and hold and to quickly recall the stored Figure - 5
measuring data. Short press to go back to measurement mode.

-4-
Clear stored data
The meter can store 50 groups of data. Once the storage is full, if user
presses again, the FUL icon will be displayed on LCD (see Figure-6).
The storage needs to be cleared in parameter setting P4 so as to keep storing
data. The numberings in M+ indicates the total number of stored data; The
numberings in RM indicates the number of stored data in current mode
(ph/mV). For example, if 20 groups of data is stored in pH mode, and 10 groups Figure - 6

in mV mode, then the numberings for M+ will be “M+30” in both pH and mV mode; the numberings for RM in
pH mode would be “RM20”, in mV mode “RM10”.

4.6 Max/Min Function

Use this function to display the maximum or minimum records out of groups of measuring data. In
measurement mode, press , LCD will display flashing icons of “MAX/MIN”, indicating the meter has
entered the mode of recording maximum and minimum data. After testing, press again, LCD will
alternately display the maximum and minimum value in the past measurements. Press to go back to
regular measurement mode.

5 pH Measurement

5.1 Preparation
Install the electrode holder
The electrode holder is composed of a metal stand base, a supporting pole, and an electrode clip. First, install
the metal stand base to the meter (screw it on). Please note that the metal base can be installed on either side
of the meter. Then install the supporting bar on the metal stand base, and then install the electrode clip on the
supporting bar.

Connect the power adapter

Plug the power adapter tightly into the DC9V socket. The power’s voltage should meet the requirements listed
on the power adapter.

Things needed in addition to what’s included in the box

A clean cup, distilled water (8-16oz), and tissue papers for rinsing and drying the probe.

5.2 pH Electrode Information

pH Electrode
The meter comes with the 201T-F 3-in-1 combination electrode with a built-in temperature sensor, which
enables the automatic temperature compensation. This electrode is only suitable for regular water solutions’
pH testing. Please refer to Section 7 for ideal pH electrodes to use for other specific applications. The
electrode’s housing adopts polycarbonate materials, which is resistant to shocks and corrosion. A 3M KCL
storage bottle comes with the electrode, which is for storing the electrode when not in use to keep the sensitivity
of the probe.

-5-
Technical Specifications of the 201T-F pH Electrode
Measurement Range: 0 - 14 pH, 0 - 80˚C (32 – 176˚F)
Junction: Single Ceramic
Reference Electrode: Ag/AgCl
Connector: BNC/RCA
Size: ø12*160 mm
Temperature unit: 30K Thermistor

Electrode Connectors
The pH electrode has two connectors: the BNC connector connects the pH probe; the RCA connector connects
the temperature sensor. Plug these two connectors into ‘pH/mV” and “TEMP” sockets. Please note not to pull
the cables in case of poor contact. Please keep the connectors clean and dry. Refer to section 4.7 regarding
how to properly maintain the pH electrode.

Use the Electrode

Screw off the KCL storage bottle, and put it aside (do not dump or spill the KCL solution). Prepare a cup of
distilled water, and rinse the electrode in it for a few seconds. Gently shake the probe to remove excess water,
and dry it with clean tissue paper (DO NOT rub or wipe the probe, just use paper to dap off excess water).
Gently stir the electrode for a few seconds after it’s dipped into the test solution and then let it stand still. Wait
for the stable measurement (a smiley face appears and stays) and then record the readings. When test is
finished, place the electrode in the storage bottle and tighten the cap in order to keep the sensitivity of the pH
sensor.

5.3 Information regarding Calibration

pH buffer solutions
The meter has 2 series of standard buffer solutions: USA and NIST (see Table-2). They can be selected
in parameter P1 (see 4.6.1).

Table-2

pH standard buffer series

Calibration icon
USA NIST

1.68 and 4.00 pH 1.68 and 4.01 pH

3-Point
7.00 pH 6.86 pH
calibration
10.01 pH 9.18 pH

3-Point Calibration
The meter can adopt 1 to 3 points of calibration. The 1st point must be using 7.00 pH (or 6.86 pH) buffer
solution, and then choose other buffers to do 2nd point and 3rd point. Please refer to Table-3 for details. In
the process of calibration, the slope of acidity range and alkalinity range will be displayed, which indicates
the health of your probe. The closer the slope is to 100%, the better the condition of the probe is.

-6-
 Table-3 Calibration Mode

Calibration
USA NIS When to adopt
icon

1-Point
7.00 pH 6.86 pH accuracy≤ ±0.1 pH
Calibration

7.00 pH and 6.86 pH and

Measuring range: 0 to 7.00 pH
4.00/1.68 pH 4.01/1.68 pH
2-Point
Calibration
7.00 pH and 10.01 pH 6.86 pH and 9.18 pH Measuring range: >7.00 pH

3-Point 7.00pH, 4.00/ 6.86pH, 4.01/

Wide measuring range
Calibration 1.68 pH and 10.01 pH 1.68pH, 9.18 pH

How often to calibrate

The frequency that you need to calibrate your meter depends on the tested samples, condition of
electrodes, and the requirement of the accuracy. For High-Accuracy meaustements (≤ ±0.02pH), the
meter should be calibrated before test every time; For ordinary-accuracy measurements (≥±0.1pH), once
calibrated, the meter can be used for about a week or longer. In the following cases, the meter must be
re-calibrated:
a) The electrode hasn’t been used for a long time or a new electrode is connected.
b) After measuring strong acid (pH<2) or strong base (pH>12) solutions.
c) After measuring fluoride-containing solution and strong organic solution
d) There is a significant difference between the temperature of the test sample and the temperature of
the buffer solution that is used in the last calibration.

-7-
5.4 pH Meter Calibration
1) Press to enter calibration mode. CAL1 icon will flash in the upper
right corner of the LCD. 7.00 pH will flash in the lower right corner of the
LCD, reminding you to use pH 7.00 buffer to conduct 1st point of
calibration.
2) Use distilled water to rinse off electrode and then dry it (with a tissue).
Dip it into pH 7.00 buffer solution, stir gently and let it stand still and wait
for the reading to become stable. In the lower right corner of LCD, the
process of auto recognizing the buffer solution will be displayed. Pressing
before the buffer is recognized will generate Er2 (please refer to
table 5).
3) When the meter locks 7.00 pH in the lower right corner, stable
icon displays on LCD. Then press key to calibrate the meter.
End icon appears after calibration is done.
The 1st point calibration is finished. In the meanwhile, CAL2 will flash at
the upper right corner, and 4.00 pH & 10.01 pH will flash alternately at the
bottom right, indicating using pH4.00 or pH10.01 buffer solution
to make the 2nd point calibration.

4) Take out the pH electrode, rinse it in distilled water, dry it, and dip
it into pH 4.00 buffer solution. Stir the solution gently and let stand still in
the buffer solution until a stable reading is reached. The meter’s display
will show the recognition process of calibration buffer solution at the lower
right corner. When the meter recognizes 4.00 pH, stable icon
displays on LCD. Press key to calibrate the meter. End icon and
electrode slope of acidity range will be displayed after calibration is done.
In the meanwhile, CL3 will flash at the upper right corner of the LCD, and
10.01 pH will flash at the lower right, indicating using pH10.01 buffer
solution to make the 3rd point calibration.

5) Take out pH electrode, rinse it in distilled water, dry it, and dip
it into pH 10.01 buffer solution. Stir the solution gently and let it stand still
in the
Figure-7
buffer solution until a stable reading is reached. The meter’s display will show
recognition process of calibration buffer solution at the bottom right of
LCD. When the meter recognizes 10.01 pH, stable icon displays on LCD. Press
key to calibrate the meter. End icon and electrode slope of alkalinity range
display after calibration is done. The meter returns to the measurement mode, the calibration icons L M
H will be displayed. Please see Figure-7 for the above calibration process.

-8-
6) During the calibration process, press key to exit from the calibration mode. The meter can
perform one-point, two-point and three-point calibration. Calibration guide icons appear on LCD.

5.5 Measuring pH
Screw off the KCL storage bottle, and put it aside (do not dump or spill the KCL solution). Prepare a cup of
distilled water, and rinse the electrode in it for a few seconds. Gently shake the probe to remove excess water,
and dry it with clean tissue paper or Kimwipes (DO NOT rub or wipe the probe, just use paper to dap off excess
water). Gently stir the electrode for a few seconds after it’s dipped into the test solution and then let it stand
still. Wait for the stable measurement (a smiley face icon appears and stays) and then record the
readings. Please refer to Figure-8 for calibration and measurement process of the pH meter.

Figure-8 Calibration and measurement process of pH meter

Submerge the After the 1st point
Press key to electrode in pH7.00 calibration is done, 1 st point
Press to turn calibration
enter the solution, press press key to
on the meter.
calibration mode. key when icon enter the
appears. measurement mode.

Submerge the After the 2nd point

electrode in pH4.00 calibration is done, 2 nd point
solution, press press key to calibration Sample
key when icon enter the Test
appears. measurement mode.

Submerge the After the 3rd point

electrode in 3rdpoint
calibration is done,
calibration
pH10.01 solution, the meter enters the
press key when measurement mode
icon appears. automatically.

Notes:

1) This default 201T-F electrode will NOT give accurate and stable pH readings when testing
purified water such as distilled or deionized water. This because those water do not have
enough ions present for the electrode to function properly. To measure distilled or deionized
water’s pH, users need to use a specialized pH electrode with the meter such as LabSenTM
803 Pure Water pH Electrode. Contact us at 1-614-285-3080 for more details. When testing
purified water like spring water or drinking water, it will take longer for the readings to get
stabilized (typically 3-5 minutes) because there is very few ions left to be detected by the
sensor in those purified water.
2) Purified water such as distilled water and deionized water are recommended for only rinsing
the probe for the best result.
3) The 201T-F pH Electrode is NOT suitable for testing high-temperature samples (>176˚F).
Testing high-temperature samples could cause permanent damage to the electrode. A
specialized electrode such as LabSenTM 213 (up to 225˚F) should be used in this situation.
4) The electrode housing is polycarbonate. When using cleaning solutions, take cautions on carbon
tetrachloride, trichlorethylene, tetrahydrofuran, acetone, etc., which will dissolve the housing and
invalidate the electrode.
-9-
5.5.1 According to the pH isothermal measurement principle, the closer the test sample’s temperature is to
the calibration solution’s, the higher the accuracy of the measurement. This principle is recommended to
follow when conducting tests for the best result. Example: If users were to test samples at 150˚F, we
recommend warming up the calibration solutions to the same temperature before performing calibrations in
order to get the most accurate readings.

5.5.2 The instrument has a function to return to factory default setting, which can be set up in P5 (refer to
section 5.6). Returning to factory default setting is to restore the meter to theoretical value (zero potential pH
is 7.00, slope is 100%), and set all the parameters to default settings. When the meter’s calibration or
measurement is performing abnormally, users can use this function to let the meter return to factory default
mode, and then conduct calibration and test again. Please note that this function is irreversible once used.

5.5.3 Self-Diagnosis

In the process of calibration and measurement, the meter has a self-diagnosis function. Please see table 5.

Table – 5 Self-diagnosis Information

Display
Contents How to fix
Icons
1. Check whether pH buffer solution is correct.
2. Check whether the meter connects the
Wrong pH buffer solution or the buffer electrode properly.
3. Check whether the electrode is damaged.
solution is out of range.
4. Make sure there is no bubble in the electrode’s
bulb.
pH electrode zero electric potential 1. Make sure there is no bubble in the
out of range (<-60mV or >60mV) electrode’s bulb.

pH electrode slope is out of range 2. Check whether the electrode is damaged.

3. Check if pH buffer solutions are correct.
(<85% or >110%)
4. The pH Electrode is aged. Replace a new one.
Press key when reading is not Press key when icon appears and
stable during calibration. stays on the screen.
1. Make sure there is no bubble in the
electrode’s bulb.
During calibration, the measuring value
2. Check whether the electrode is damaged.
is not stable for ≥3min. 3. The pH Electrode is aged. Replace a new
one.

* If you find any air bubble in the glass bulb of the pH sensor, simply shake the probe for a few times
to remove it. The existence of an air bubble in the glass bulb will significantly decrease the stableness
of measurement.

- 10 -
5.6 Parameter Setting
Table-6

Symbol Parameter setting content Parameter Factory default setting

P1 Select pH buffer series USA - NIST USA

P2 Select resolution 0.1/0.01 pH 0.01 pH

P3 Select temperature unit ℃-℉ ℃

P4 Clear stored data No-Yes No

P5 Return to factory default No-Yes No

5.6.1 How to do the parameter setting:

In measurement mode, long press to enter parameter setting P1. Then press to change menu
from P1 to P2…P5. For details, please see Table-7.
Table-7 pH Parameter Setting

P1 — Select pH buffer series (USA— NIS)

1. Long press to enter P1.
2. Press , USA flashes, press to select USA or NIS, press to
confirm; USA — USA Series，NIS — NIST Series
3. Press to enter P2 or press to return to measurement mode.

P2 — Select resolution (0.01—0.1)

1. Press , 0.01 flashes, press to select 0.01 or 0.1, press
to confirm;
2. Press to enter P3 or press to return to measurement mode.

P3 — Select temperature unit (°C—°F)

1. Press , °C flashes, press to select °C or °F, press
to confirm;
2. Press to enter P4 or press to return to measurement mode.

P4 — Clear stored data (No—Yes)

1. Press , “No” flashes, press to select No or Yes, press
to confirm;
2. Press to enter P5 or press to return to measurement mode.

P5 — Restore to factory default setting (No—Yes)

1. Press , “No” flashes, press to select No to Yes, press
to confirm; The meter returns to measurement mode.
2. If not selecting “Yes”, press to return to measurement mode.

- 11 -
5.7 pH Electrode’s Maintenance
5.7.1 Daily maintenance
The soaking solution contained in the supplied protective bottle is used to maintain activation in the glass bulb
and junction. Loosen the cap, take out the electrode and rinse in distilled or water before taking a measurement.
Insert the electrode and tighten the cap after measurements to prevent the solution from leaking. If the soaking
solution is cloudy or moldy, replace the 3M KCL solution.

* We DO NOT recommend using other brand’s soaking solution, since different chemicals can be used
and potential damage can be caused to the electrode)

* The electrode should NOT be soaked and stored in purified or distilled water, protein solution, acid fluoride
solution, or organic lipids. Distilled water or purified water is only recommended for rinsing electrodes.

5.7.2 Calibration buffer solution

For calibration accuracy, the pH of the standard buffer solution must be reliable. The buffer solution should be
refreshed often, especially after heavy use. We recommend 10-15 times of use before replacing the pH buffers.

5.7.3 Protect glass bulb

The sensitive glass bulb at the front of the combination electrode should not come in contact with hard surfaces.
Scratches or cracks on the electrode will cause inaccurate readings. Before and after each measurement, the
electrode should be rinsed with distilled water or purified water. If a sample sticks to the electrode or it’s
contaminated, the electrode should be thoroughly cleaned using a soft brush with soap water and then rinsed
with distilled water. After that, soak it in the KCL solution again for at least 6 hours.

5.7.4 Renew glass bulb

Electrodes that have been used over a long period of time will become aged. Submerge the electrode in
0.1mol/L hydrochloric acid 24 hours, then rinse the electrode in distilled water, then submerge it in KCL soaking
solution for 24 hours.
The method to prepare 0.1mol/L hydrochloric acid: dilute 9mL hydrochloric acid in distilled water to 1000mL.
For serious passivation, submerge the bulb in 4% HF (hydrofluoric acid) for 3-5 seconds, and wash it in
distilled water, then submerge it in the soaking solution for 24 hours to renew it.

5.7.5 Clean contaminated glass bulb and junction (please refer to Table-8)

Table-8 Clean contaminated glass bulb and junction

Contamination Cleaning Solutions

Inorganic metal oxide Dilute acid less than 1mol/L

Organic lipid Dilute detergent (weak alkaline)

Resin macromolecule Dilute alcohol, acetone, ether

Proteinic haematocyte sediment Acidic enzymatic solution (saccharated yeast tablets)

Paints Dilute bleacher, peroxide

- 12 -
6 mV measurement

6.1 ORP measurement

Press key, and switch the meter to mV measurement mode. Connect ORP electrode (the 301Pt-C
combination ORP electrode is sold separately) and dip it in sample solution, stir the solution briefly and allow
it to stay in the solution until icon appears and get the reading.
ORP means Oxidation Reduction Potential. The unit is mV.

6.2 Notes on ORP measurement

6.2.1 ORP measurement does not require calibration. When the user is not sure about ORP electrode quality
or measuring value, use ORP standard solution to test mV value and see whether ORP electrode or meter
works properly. Table-9 is the data of standard ORP solution for 222 mV.
Table-9
°C 10 15 20 25 30 35 38 40
mV 242 235 227 222 215 209 205 201

6.2.2 Clean and activate ORP electrode

After the electrode has been used over a long period of time, the platinum surface will get polluted which
causes inaccurate measurement and slow response. Please refer to the following methods to clean and
activate ORP electrode:
(a) For inorganic pollutant, submerge the electrode in 0.1mol/L dilute hydrochloric acid for 30 minutes, then
wash it in distilled water, then submerge it in the soaking solution for 6 hours.
(b) For organic or lipid pollutant, clean the platinum surface with detergent, then wash it in distilled water, then
submerge it in the soaking solution for 6 hours.
(c) For heavily polluted platinum surface on which there is oxidation film, polish the platinum surface with
toothpaste, then wash it in distilled water, then submerge it in the soaking solution for 6 hours.

- 13 -
7 Recommended pH Electrodes for Specific Applications

Application Ideal Apera pH Electrodes to Use with

PH700 Meter
Regular water solutions 201T-F, LabSen 213
Beverage, beer, or wine analysis LabSen 213
Cosmetics LabSen 851-1, (MP500 temp. probe
required)
Dairy products (milk, cream, yogurt, mayo, etc.) LabSen 823
High-Temperature liquid LabSen 213
Low-temperature liquid LabSen881 (MP500 temp. probe required)
Meat LabSen 763
Micro sample testing LabSen 241-6, LabSen 241-3 (MP500 temp.
probe required)
Purified Water (Low ion concentration samples) LabSen 803, LabSen 813
Soil LabSen 553
Solid or semi-solid samples (cheese, rice, fruit, etc.) LabSen 753
Strong acid samples LabSen 831 (MP500 temp. probe required)
Strong alkalined samples LabSen 841 (MP500 temp. probe required)
Surface test (skin, paper, carpet, etc.) LabSen 371 (MP500 temp. probe required)
Titration LabSen 223
TRIS buffer solutions LabSen 213, LabSen 223
Viscous liquid samples LabSen 223, LabSen851-1
Wastewater or emulsion LabSen 333

8 Warranty

We warrant this instrument to be free from defects in material and workmanship and agree to repair or replace
free of charge, at option of APERA INSTRUMENTS(Europe) GmbH, any malfunctioned or damaged product
attributable to responsibility of APERA INSTRUMENTS(Europe) GmbH for a period of TWO YEARS (SIX
MONTHS for the probe) from the delivery.

This limited warranty does not cover any damages due to:
Transportation, storage, improper use, failure to follow the product instructions or to perform any preventive
maintenance, modifications, combination or use with any products, materials, processes, systems or other
matter not provided or authorized in writing by us, unauthorized repair, normal wear and tear, or external
causes such as accidents, abuse, or other actions or events beyond our reasonable control.

APERA INSTRUMENTS (Europe) GmbH

Wilhelm-Muthmann-Straße 18, 42329 Wuppertal Germany
Email: [email protected] |ww.aperainst.de | Tel. +49 202 51988998
- 14 -