CYNO 2 CPS

Single Component Adhesive 1 of 2

Product Description
Pioneer CYNO 2 CPS is an instant
bonding, one-component, solvent-free
cyanoacrylate adhesive. It exhibits highly
flowability and good penetration for fitting
smooth surfaces. It forms strong bonds on
a wide variety of substrates without the
need for clamping, heat or added catalyst.

Key Features
• Quick setting
• Fast curing
• Forms strong bonds
• Easy to use and apply
• No clamping necessary
• No mixing required

Product Specifications / Typical Applications

Properties / Physical Characteristics • For woodworking (especially for acidic
Table 1: Physical Properties (Uncured) woods)
Parameters Results • Plastic
• Rubber
1. Base Ethyl Cyanoacrylate
• Metal
2. Appearance Clear, Colorless liquid
3. Specific Gravity @20ºC 1.04 Limitations
4. Flash Point 80ºC • Not waterproof
5. Viscosity @ 25ºC 2-30 cps • Not for gap-filling purposes (materials
6. Boiling Point > 149ºC need to be close-fitting to bond properly)
• Not recommended for items with direct
Table 2: Physical Properties (Cured) contact to hot liquids
Parameters Results
Application Procedure
1. Setting Time A. Surface Preparation
-Stainless steel Max. of 5 seconds Make sure that the surfaces to be bonded
-Aluminum Max. of 5 seconds are free from dust, oil, water or lubricant
! -PVC Max. of 5 seconds B. Method
-ABS Max. of 5 seconds 1. Dispense a drop or drops on one surface.
Apply just enough to leave a thin film after
2. Pull-Off Strength
compression.
-Steel > 350 psi 2. Press parts together and hold firmly for a
3. Tensile Shear Strength >1422.33 few seconds. Good contact is essential.
4. Service Temperature Range -55-82ºC An adequate bond develops in less than 1
5. Full Cure Time 24 hours minute.
*Typical Values and characteristics only. 3. Wipe off excess adhesive from the top of
the nozzle.
4. Recap. If left uncapped, the contents may
deteriorate by contamination from
moisture in the air.
2 of 2

Note: Due to polymerization, blooming or Keep away from heat/sparks/open flame/hot surfaces.
whitening on the surface of the bottle or No smoking during use.
bonded materials will occur. Wipe with a Avoid breathing mist or vapors.
cloth damped with acetone or Mighty Wash the hand or face by soap and water after handling.
Use only in a well-ventilated area.
Remover.
Wear protective polyethylene gloves/protective clothing/eye or
C. Cleaning face protection.
Tools and equipments used during
application may be cleaned using Pioneer If on skin: Wash with plenty of soap and water.
Mighty Remover. For soiled hands, wipe with If in eyes: Rinse cautiously with water for several minutes. Remove
cloth dampened with Pioneer Mighty contact lenses, if present, and easy to do. Continue rinsing.
Remover, then, wash with soap and water. If skin or eye irritation occurs: Get medical advice/attention.
If inhaled: Remove person to fresh air and keep comfortable for
Handy Tips breathing.
• For best results, ensure that substrates to Take off contaminated clothing and wash it before re-use.
be joined are close fitting. In case of fire: Use carbon dioxide/dry chemical to extinguish.
• For fast cure results, use 1 drop per
square inch. Does not use in large KEEP OUT OF REACH OF CHILDREN.
amounts as this will cure slower.
• Full bond strength is achieved after 24 Warranty and Disclaimers
hours. Unless an additional warranty is specifically stated on the
• When fingers get stuck together, apply applicable product packaging or product literature, Pioneer
warrants that each Pioneer product conforms with the
drops of Pioneer Mighty Remover at the
applicable Pioneer product specification at the time of
affected areas. Then, slowly, twist fingers shipment, and when properly used and maintained in
together in the opposite direction accordance with Pioneer’s current published Technical Data
Sheet (TDS), will serve the purpose for which it is intended. The
Packaging recommendations and statements in Pioneer’s TDS are based
20g and 50g bottles on good building practice but are not, by any means, an
exhaustive statement of all relevant information. Pioneer shall
Storage not be liable for the recommendations in its TDS and the
Cool, dry place away from direct sunlight and performance of the relevant Product. Pioneer shall also not be
liable for any claims, damages or defects arising from, or in any
preferably 30ºC maximum.
way attributable to poor workmanship, incorrect design or
detailing, use of the Pioneer product in unsuitable conditions,
Shelf Life and force majeure.
6 months from filling date Pioneer MAKES NO OTHER WARRANTIES, CONDITIONS OR
REPRESENTATIONS, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR
Health and Safety Precautions CONDITION OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR
CONDITION ARISING OUT OF A COURSE OF DEALING,
CUSTOMER OR USAGE OF TRADE. If the Pioneer product
does not conform to this warranty, then the sole and exclusive
DANGER remedy is, at Pioneer’s option, the replacement of the Pioneer
Combustible liquid. product or refund of the purchase price.
Causes skin, eye or respiratory irritation.
May cause an allergic skin reaction. Limited Liability
Hazards Except where prohibited by law, Pioneer will not be liable for
Causes skin and eye irritation. any loss or damage arising from the use or application of the
May cause an allergic skin reaction. Pioneer product, whether direct, indirect, special, incidental or
Toxic to aquatic life with long lasting effects. consequential, regardless of the legal theory asserted,
Precaution including warranty, contract, negligence or strict liability.
TDS Pioneer - 022019 Version