DRIVER CONTROLS

SECTION
EXTERIOR LIGHTING SYSTEM
EXL B

E
CONTENTS
TYPE 1 HEADLAMP AIMING CONTROL (MANUAL) : F
System Description ..................................................15
HOW TO USE THIS MANUAL ...................... 7
FRONT FOG LAMP SYSTEM ...................................15
G
APPLICATION NOTICE ...................................... 7 FRONT FOG LAMP SYSTEM : System Diagram....16
Information ................................................................ 7 FRONT FOG LAMP SYSTEM : System Descrip-
tion ...........................................................................16
PRECAUTION ............................................... 8 FRONT FOG LAMP SYSTEM : Fail-Safe ...............16 H

PRECAUTIONS ................................................... 8 REAR FOG LAMP SYSTEM ......................................16

Precaution for Supplemental Restraint System REAR FOG LAMP SYSTEM : System Diagram ......17
I
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- REAR FOG LAMP SYSTEM : System Description....17
SIONER" ................................................................... 8
Precautions Necessary for Steering Wheel Rota- TURN SIGNAL AND HAZARD WARNING LAMP
tion After Battery Disconnection ................................ 8 SYSTEM .....................................................................17 J
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM DESCRIPTION ............................. 10 SYSTEM : System Diagram ....................................17
TURN SIGNAL AND HAZARD WARNING LAMP
K
COMPONENT PARTS .......................................10 SYSTEM : System Description ................................17
Component Parts Location ...................................... 10
Component Description .......................................... 11 PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM .....................................................................18 EXL
SYSTEM .............................................................12 PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM : System Diagram ....................................18
HEADLAMP SYSTEM ............................................... 12 PARKING, LICENSE PLATE AND TAIL LAMP
HEADLAMP SYSTEM : System Diagram ............... 12 M
SYSTEM : System Description ................................18
HEADLAMP SYSTEM : System Description ........... 12 PARKING, LICENSE PLATE AND TAIL LAMP
HEADLAMP SYSTEM : Fail-Safe ........................... 13 SYSTEM : Fail-Safe ................................................19
N
AUTO LIGHT SYSTEM (EXCEPT FOR HONG EXTERIOR LAMP BATTERY SAVER SYSTEM .......19
KONG) ....................................................................... 13 EXTERIOR LAMP BATTERY SAVER SYSTEM :
AUTO LIGHT SYSTEM (EXCEPT FOR HONG System Diagram ......................................................19
KONG) : System Diagram ....................................... 13 O
EXTERIOR LAMP BATTERY SAVER SYSTEM :
AUTO LIGHT SYSTEM (EXCEPT FOR HONG System Description ..................................................19
KONG) : System Description .................................. 13
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI- P
AUTO LIGHT SYSTEM (FOR HONG KONG) ........... 14
GENT KEY SYSTEM) ....................................... 21
AUTO LIGHT SYSTEM (FOR HONG KONG) :
System Diagram ...................................................... 14 COMMON ITEM .........................................................21
AUTO LIGHT SYSTEM (FOR HONG KONG) : COMMON ITEM : CONSULT Function (BCM -
System Description ................................................. 14 COMMON ITEM) .....................................................21
HEADLAMP AIMING CONTROL (MANUAL) ........... 15 HEADLAMP ...............................................................22

EXL-1
 HEADLAMP : CONSULT Function (BCM - HEAD EXTERIOR LAMP FUSE ................................... 82
LAMP) (Except India Production For Europe and Diagnosis Procedure ............................................... 82
General Areas) ....................................................... 22
HEADLAMP (HI) CIRCUIT ................................ 83
FLASHER .................................................................. 24 Component Function Check ................................... 83
FLASHER : CONSULT Function (BCM - FLASH- Diagnosis Procedure ............................................... 83
ER) (Except India Production For Europe and
General Areas) ....................................................... 24 HEADLAMP (LO) CIRCUIT ............................... 85
Component Function Check ................................... 85
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN- Diagnosis Procedure ............................................... 85
TELLIGENT KEY SYSTEM) .............................. 26
HEADLAMP GROUND CIRCUIT ...................... 87
COMMON ITEM ........................................................ 26 Diagnosis Procedure ............................................... 87
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) .................................................... 26 HEADLAMP AIMING SYSTEM (MANUAL) ...... 88
Component Inspection ............................................ 88
HEADLAMP .............................................................. 26
HEADLAMP : CONSULT Function (BCM - HEAD PARKING LAMP CIRCUIT ................................ 89
LAMP) (Except India Production For Europe and Component Function Check ................................... 89
General Areas) ....................................................... 26 Diagnosis Procedure ............................................... 89

FLASHER .................................................................. 29 TAIL LAMP CIRCUIT ........................................ 91

FLASHER : CONSULT Function (BCM - FLASH- Component Function Check ................................... 91
ER) (Except India Production For Europe and Diagnosis Procedure ............................................... 91
General Areas) ....................................................... 29
LICENSE PLATE LAMP CIRCUIT .................... 92
DIAGNOSIS SYSTEM (IPDM E/R) (WITH IN- Component Function Check ................................... 92
TELLIGENT KEY SYSTEM) .............................. 30 Diagnosis Procedure ............................................... 92
Diagnosis Description ............................................. 30
CONSULT Function (IPDM E/R) ............................ 32 OPTICAL SENSOR ........................................... 93
Component Function Check ................................... 93
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT Diagnosis Procedure ............................................... 93
INTELLIGENT KEY SYSTEM) .......................... 34
Diagnosis Description ............................................. 34 FRONT FOG LAMP CIRCUIT ........................... 96
CONSULT Function (IPDM E/R) ............................ 36 Component Function Check ................................... 96
Diagnosis Procedure ............................................... 96
ECU DIAGNOSIS INFORMATION .............. 38
FRONT FOG LAMP RELAY .............................. 98
BCM, IPDM E/R ................................................. 38 Diagnosis Procedure ............................................... 98
List of ECU Reference ............................................ 38 Component Inspection ............................................ 99

WIRING DIAGRAM ..................................... 39 REAR FOG LAMP CIRCUIT ............................ 100

Component Function Check ................................. 100
EXTERIOR LIGHTING SYSTEM ....................... 39 Diagnosis Procedure ............................................. 100
Application Notice ................................................... 39
TURN SIGNAL LAMP CIRCUIT ....................... 102
TYPE A ...................................................................... 39 Component Function Check ................................. 102
TYPE A : Wiring Diagram ....................................... 40 Diagnosis Procedure ............................................. 102
TYPE B ...................................................................... 55 HAZARD SWITCH ............................................ 105
TYPE B : Wiring Diagram ....................................... 56 Component Function Check ................................. 105
Diagnosis Procedure ............................................. 105
TYPE C ...................................................................... 73
TYPE C : Wiring Diagram ....................................... 74 SYMPTOM DIAGNOSIS ........................... 107
BASIC INSPECTION ................................... 79 EXTERIOR LIGHTING SYSTEM SYMPTOMS.. 107
Symptom Table ..................................................... 107
DIAGNOSIS AND REPAIR WORKFLOW ......... 79
Work Flow ............................................................... 79 BOTH SIDE HEADLAMPS (HI) ARE NOT
TURNED ON ..................................................... 109
DTC/CIRCUIT DIAGNOSIS ......................... 82
Description ............................................................ 109
Diagnosis Procedure ............................................. 109

EXL-2
BOTH SIDE HEADLAMPS (LO) ARE NOT Replacement ......................................................... 131
TURNED ON ..................................................... 110 A
Description ............................................................ 110
HIGH-MOUNTED STOP LAMP ...................... 133
Diagnosis Procedure ............................................. 110 WITHOUT REAR SPOILER ..................................... 133
WITHOUT REAR SPOILER : Exploded View ....... 133 B
PARKING, LICENSE PLATE AND TAIL
WITHOUT REAR SPOILER : Removal and Instal-
LAMPS ARE NOT TURNED ON ...................... 111 lation ...................................................................... 133
Description ............................................................ 111
WITHOUT REAR SPOILER : Replacement .......... 134 C
Diagnosis Procedure ............................................. 111
WITH REAR SPOILER ............................................ 134
BOTH SIDE FRONT FOG LAMPS ARE NOT WITH REAR SPOILER : Exploded View ............... 134
TURNED ON ..................................................... 112 WITH REAR SPOILER : Removal and Installation.. 134 D
Description ............................................................ 112
Diagnosis Procedure ............................................. 112 LICENSE PLATE LAMP ................................. 135
Exploded View ....................................................... 135
PERIODIC MAINTENANCE ....................... 113 E
Removal and Installation ....................................... 135
Replacement ......................................................... 135
HEADLAMP AIMING ADJUSTMENT .............. 113
HEADLAMP AIMING SWITCH ....................... 136 F
LHD .......................................................................... 113
Exploded View ....................................................... 136
LHD : Description .................................................. 113
Removal and Installation ....................................... 136
LHD : Aiming Adjustment Procedure .................... 114
SERVICE DATA AND SPECIFICATIONS G
RHD ......................................................................... 115
RHD : Description ................................................. 115 (SDS) .......................................................... 137
RHD : Aiming Adjustment Procedure .................... 116
SERVICE DATA AND SPECIFICATIONS H
FRONT FOG LAMP AIMING ADJUSTMENT .. 118 (SDS) ............................................................... 137
Description ............................................................ 118 Bulb Specifications ................................................ 137
Aiming Adjustment Procedure ............................... 118 TYPE 2 I

REMOVAL AND INSTALLATION ............. 120 HOW TO USE THIS MANUAL .................. 138
FRONT COMBINATION LAMP ........................ 120 APPLICATION NOTICE .................................. 138 J
Exploded View ...................................................... 120 Information ............................................................. 138
Removal and Installation ....................................... 121
Replacement ......................................................... 121 PRECAUTION ............................................ 139 K
Disassembly and Assembly .................................. 122
PRECAUTIONS ............................................... 139
FRONT FOG LAMP .......................................... 123
FOR EUROPE .......................................................... 139 EXL
Exploded View ...................................................... 123
FOR EUROPE : Precaution for Supplemental Re-
Removal and Installation ....................................... 123
straint System (SRS) "AIR BAG" and "SEAT BELT
Replacement ......................................................... 123
PRE-TENSIONER" ................................................ 139 M
OPTICAL SENSOR .......................................... 125 FOR EUROPE : Precautions Necessary for Steer-
Removal and Installation ....................................... 125 ing Wheel Rotation After Battery Disconnection .... 139

LIGHTING & TURN SIGNAL SWITCH ............ 126 EXCEPT FOR EUROPE .......................................... 140 N
Exploded View ...................................................... 126 EXCEPT FOR EUROPE : Precaution for Supple-
mental Restraint System (SRS) "AIR BAG" and
SIDE TURN SIGNAL LAMP ............................. 127 "SEAT BELT PRE-TENSIONER" .......................... 140 O
Exploded View ...................................................... 127 EXCEPT FOR EUROPE : Precautions Necessary
Removal and Installation ....................................... 127 for Steering Wheel Rotation After Battery Discon-
Replacement ......................................................... 127 nection ................................................................... 140
P
HAZARD SWITCH ............................................ 129 SYSTEM DESCRIPTION ........................... 142
Exploded View ...................................................... 129
Removal and Installation ....................................... 129 COMPONENT PARTS .................................... 142
Component Parts Location .................................... 142
REAR COMBINATION LAMP .......................... 130 Component Description ........................................ 143
Exploded View ...................................................... 130 Light & Rain Sensor ............................................... 143
Removal and Installation ....................................... 130

EXL-3
SYSTEM ........................................................... 144 HEADLAMP : CONSULT Function (BCM - HEAD
LAMP) (India Production For Europe and General
HEADLAMP SYSTEM ..............................................144 Areas) ................................................................... 155
HEADLAMP SYSTEM : System Diagram ..............144
HEADLAMP SYSTEM : System Description .........144 FLASHER ................................................................ 157
HEADLAMP SYSTEM : Fail-Safe ..........................145 FLASHER : CONSULT Function (BCM - FLASH-
ER) (India Production For Europe and General Ar-
AUTO LIGHT SYSTEM ............................................145 eas) ....................................................................... 157
AUTO LIGHT SYSTEM : System Diagram ............145
AUTO LIGHT SYSTEM : System Description .......146 DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) ............................. 159
DAYTIME RUNNING LIGHT SYSTEM ....................146
DAYTIME RUNNING LIGHT SYSTEM : System COMMON ITEM ....................................................... 159
Diagram .................................................................147 COMMON ITEM : CONSULT Function (BCM -
DAYTIME RUNNING LIGHT SYSTEM : System COMMON ITEM) .................................................. 159
Description .............................................................147
HEADLAMP ............................................................. 159
HEADLAMP AIMING CONTROL (MANUAL) ..........147 HEADLAMP : CONSULT Function (BCM - HEAD
HEADLAMP AIMING CONTROL (MANUAL) : LAMP) (India Production For Europe and General
System Description ................................................147 Areas) ................................................................... 159
FRONT FOG LAMP SYSTEM ..................................147 FLASHER ................................................................ 161
FRONT FOG LAMP SYSTEM : System Diagram..148 FLASHER : CONSULT Function (BCM - FLASH-
FRONT FOG LAMP SYSTEM : System Descrip- ER) (India Production For Europe and General Ar-
tion .........................................................................148 eas) ....................................................................... 161
FRONT FOG LAMP SYSTEM : Fail-Safe ..............148
DIAGNOSIS SYSTEM (IPDM E/R) (WITH IN-
REAR FOG LAMP SYSTEM ....................................148 TELLIGENT KEY SYSTEM) ............................. 163
REAR FOG LAMP SYSTEM : System Diagram ....149 Diagnosis Description ........................................... 163
REAR FOG LAMP SYSTEM : System Description..149 CONSULT Function (IPDM E/R) ........................... 165
TURN SIGNAL AND HAZARD WARNING LAMP DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT
SYSTEM ...................................................................149 INTELLIGENT KEY SYSTEM) ......................... 167
TURN SIGNAL AND HAZARD WARNING LAMP Diagnosis Description ........................................... 167
SYSTEM : System Diagram ..................................149
CONSULT Function (IPDM E/R) ........................... 169
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Description ..............................149 ECU DIAGNOSIS INFORMATION ............ 171
PARKING, LICENSE PLATE AND TAIL LAMP BCM, IPDM E/R ................................................ 171
SYSTEM ...................................................................150 List of ECU Reference .......................................... 171
PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM : System Diagram ..................................150 WIRING DIAGRAM ................................... 172
PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM : System Description ..............................151 EXTERIOR LIGHTING SYSTEM ...................... 172
PARKING, LICENSE PLATE AND TAIL LAMP Application Notice ................................................. 172
SYSTEM : Fail-Safe ..............................................151
TYPE A .................................................................... 172
EXTERIOR LAMP BATTERY SAVER SYSTEM .....151 TYPE A : Wiring Diagram ..................................... 173
EXTERIOR LAMP BATTERY SAVER SYSTEM :
TYPE B .................................................................... 190
System Diagram ....................................................152
TYPE B : Wiring Diagram ..................................... 191
EXTERIOR LAMP BATTERY SAVER SYSTEM :
System Description ................................................152 TYPE C .................................................................... 203
TYPE C : Wiring Diagram ..................................... 204
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) ...................................... 154 BASIC INSPECTION ................................. 209
COMMON ITEM .......................................................154 DIAGNOSIS AND REPAIR WORKFLOW ........ 209
COMMON ITEM : CONSULT Function (BCM - Work Flow ............................................................. 209
COMMON ITEM) ...................................................154
DTC/CIRCUIT DIAGNOSIS ....................... 212
HEADLAMP .............................................................155
EXTERIOR LAMP FUSE .................................. 212

EXL-4
 Diagnosis Procedure ............................................. 212 LICENSE PLATE LAMP CIRCUIT .................. 233
Component Function Check .................................. 233 A
HEADLAMP (HI) CIRCUIT ............................... 214 Diagnosis Procedure ............................................. 233
Component Function Check .................................. 214
Diagnosis Procedure ............................................. 214 LIGHT & RAIN SENSOR ................................ 235
B
Component Function Check .................................. 235
HEADLAMP (LO) CIRCUIT .............................. 216 Diagnosis Procedure ............................................. 235
Component Function Check .................................. 216
Diagnosis Procedure ............................................. 216 FRONT FOG LAMP CIRCUIT ......................... 237 C
Component Function Check .................................. 237
HEADLAMP GROUND CIRCUIT ..................... 218 Diagnosis Procedure ............................................. 237
Diagnosis Procedure ............................................. 218
FRONT FOG LAMP RELAY ........................... 239 D
HEADLAMP AIMING SYSTEM (MANUAL) ..... 219 Diagnosis Procedure ............................................. 239
Component Inspection .......................................... 219 Component Inspection ........................................... 240
E
TAIL LAMP LH RELAY CIRCUIT .................... 220 REAR FOG LAMP CIRCUIT ........................... 241
WITHOUT DAYTIME RUNNING LIGHT SYSTEM .. 220 Component Function Check .................................. 241
WITHOUT DAYTIME RUNNING LIGHT SYSTEM Diagnosis Procedure ............................................. 241
F
: Diagnosis Procedure ........................................... 220 TURN SIGNAL LAMP CIRCUIT ..................... 243
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
Component Function Check .................................. 243
: Component Inspection ........................................ 221
Diagnosis Procedure ............................................. 243 G
WITH DAYTIME RUNNING LIGHT SYSTEM .......... 221
HAZARD SWITCH .......................................... 246
WITH DAYTIME RUNNING LIGHT SYSTEM : Di-
Component Function Check .................................. 246
agnosis Procedure ................................................ 221 H
Diagnosis Procedure ............................................. 246
WITH DAYTIME RUNNING LIGHT SYSTEM :
Component Inspection .......................................... 223 SYMPTOM DIAGNOSIS ............................ 248
TAIL LAMP RH RELAY CIRCUIT .................... 224 I
EXTERIOR LIGHTING SYSTEM SYMPTOMS. 248
WITHOUT DAYTIME RUNNING LIGHT SYSTEM .. 224 WITHOUT DAYTIME RUNNING LIGHT SYSTEM .. 248
WITHOUT DAYTIME RUNNING LIGHT SYSTEM WITHOUT DAYTIME RUNNING LIGHT SYSTEM J
: Diagnosis Procedure ........................................... 224 : Symptom Table ................................................... 248
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
: Component Inspection ........................................ 225 WITH DAYTIME RUNNING LIGHT SYSTEM .......... 249
WITH DAYTIME RUNNING LIGHT SYSTEM : K
WITH DAYTIME RUNNING LIGHT SYSTEM .......... 225 Symptom Table ..................................................... 250
WITH DAYTIME RUNNING LIGHT SYSTEM : Di-
agnosis Procedure ................................................ 225 BOTH SIDE HEADLAMPS (HI) ARE NOT EXL
WITH DAYTIME RUNNING LIGHT SYSTEM : TURNED ON ................................................... 252
Component Inspection .......................................... 227 Description ............................................................. 252
Diagnosis Procedure ............................................. 252
PARKING LAMP CIRCUIT ............................... 228 M
Component Function Check .................................. 228 BOTH SIDE HEADLAMPS (LO) ARE NOT
Diagnosis Procedure ............................................. 228 TURNED ON ................................................... 253
Description ............................................................. 253 N
TAIL LAMP CIRCUIT ....................................... 230
Diagnosis Procedure ............................................. 253
WITHOUT DAYTIME RUNNING LIGHT SYSTEM .. 230
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
PARKING, LICENSE PLATE AND TAIL
O
: Component Function Check ................................ 230 LAMPS ARE NOT TURNED ON ..................... 254
WITHOUT DAYTIME RUNNING LIGHT SYSTEM WITHOUT DAYTIME RUNNING LIGHT SYSTEM .. 254
: Diagnosis Procedure ........................................... 230 WITHOUT DAYTIME RUNNING LIGHT SYSTEM P
WITH DAYTIME RUNNING LIGHT SYSTEM .......... 231 : Description ........................................................... 254
WITH DAYTIME RUNNING LIGHT SYSTEM : WITHOUT DAYTIME RUNNING LIGHT SYSTEM
Component Function Check .................................. 231 : Diagnosis Procedure ........................................... 254
WITH DAYTIME RUNNING LIGHT SYSTEM : Di- WITH DAYTIME RUNNING LIGHT SYSTEM .......... 254
agnosis Procedure ................................................ 231 WITH DAYTIME RUNNING LIGHT SYSTEM : De-
scription ................................................................. 254

EXL-5
 WITH DAYTIME RUNNING LIGHT SYSTEM : Di- SIDE TURN SIGNAL LAMP ............................. 271
agnosis Procedure .................................................254 Exploded View ...................................................... 271
Removal and Installation ....................................... 271
BOTH SIDE FRONT FOG LAMPS ARE NOT Replacement ......................................................... 271
TURNED ON .................................................... 256
Description .............................................................256 HAZARD SWITCH ............................................ 273
Diagnosis Procedure .............................................256 Exploded View ...................................................... 273
Removal and Installation ....................................... 273
PERIODIC MAINTENANCE ....................... 257
REAR COMBINATION LAMP .......................... 274
HEADLAMP AIMING ADJUSTMENT ............. 257 Exploded View ...................................................... 274
Removal and Installation ....................................... 274
LHD ..........................................................................257
Replacement ......................................................... 275
LHD : Description ..................................................257
LHD : Aiming Adjustment Procedure .....................258 HIGH-MOUNTED STOP LAMP ........................ 277
RHD ..........................................................................259 WITHOUT REAR SPOILER .................................... 277
RHD : Description ..................................................259 WITHOUT REAR SPOILER : Exploded View ....... 277
RHD : Aiming Adjustment Procedure ....................260 WITHOUT REAR SPOILER : Removal and Instal-
lation ..................................................................... 277
FRONT FOG LAMP AIMING ADJUSTMENT . 262
WITHOUT REAR SPOILER : Replacement ......... 278
Description .............................................................262
Aiming Adjustment Procedure ...............................262 WITH REAR SPOILER ............................................ 278
WITH REAR SPOILER : Exploded View .............. 278
REMOVAL AND INSTALLATION .............. 264 WITH REAR SPOILER : Removal and Installation. 278
FRONT COMBINATION LAMP ....................... 264 LICENSE PLATE LAMP ................................... 279
Exploded View .......................................................264 Exploded View ...................................................... 279
Removal and Installation .......................................265 Removal and Installation ....................................... 279
Replacement .........................................................265 Replacement ......................................................... 279
Disassembly and Assembly ...................................266
HEADLAMP AIMING SWITCH ......................... 280
FRONT FOG LAMP ......................................... 267 Exploded View ...................................................... 280
Exploded View .......................................................267 Removal and Installation ....................................... 280
Removal and Installation .......................................267
Replacement .........................................................267 SERVICE DATA AND SPECIFICATIONS
LIGHT & RAIN SENSOR ................................. 269 (SDS) ......................................................... 281
Exploded View .......................................................269 SERVICE DATA AND SPECIFICATIONS
Removal and Installation .......................................269 (SDS) ................................................................ 281
LIGHTING & TURN SIGNAL SWITCH ............ 270 Bulb Specifications ................................................ 281
Exploded View .......................................................270

EXL-6
 APPLICATION NOTICE
< HOW TO USE THIS MANUAL > [TYPE 1]

HOW TO USE THIS MANUAL A

APPLICATION NOTICE
Information INFOID:0000000006757239
B
• Check the vehicle type to use the service information in this section.

Service information Destination C

• General areas
Thai production models • Australia and New Zealand
• Hong Kong D
Type 1
China production models China
India production models India
E
• Europe (LH and RH drive)
Type 2 India production models • Lebanon and Jordan
• General areas (LH and RH drive)
Refer to general information. F
• In this manual, “Idling Stop System” is referred to as “Stop / Start System”.

EXL

EXL-7
 PRECAUTIONS
< PRECAUTION > [TYPE 1]

PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000006113688

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
INFOID:0000000006113689

CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.

EXL-8
 PRECAUTIONS
< PRECAUTION > [TYPE 1]
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock A
when the ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT.
B

EXL

EXL-9
 COMPONENT PARTS
< SYSTEM DESCRIPTION > [TYPE 1]

SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location INFOID:0000000005912270

JMLIA1578ZZ

1. Remote keyless entry receiver*1 2. Hazard switch 3. Push-button ignition switch*2

Refer to DLK-28,
"Component Parts Location"
4. Combination switch 5. Key switch*3 6. Headlamp aiming switch*4
7. Combination meter 8. IPDM E/R 9. Front turn signal lamp
Refer to PCS-8, "Component Parts
Location".
10. Headlamp 11. Parking lamp 12. Front fog lamp*5
13. BCM 14. Side turn signal lamp 15. Optical sensor*6
Refer to BCS-9, "BODY CONTROL
SYSTEM : Component Parts Loca-
tion".
16. Rear fog lamp*7 17. License plate lamp 18. Tail lamp
19. Rear turn signal lamp 20. Front door switch (driver side) 21. Front door request switch (driver
side)*2
22. Remote keyless entry receiver*8 23. Aiming motor*4 24. Front fog lamp relay*5
Refer to DLK-28,
"Component Parts Location"
A. Front combination lamp (back) B. View with glove box cover assembly
is removed

*1: For Hong Kong

EXL-10
 COMPONENT PARTS
< SYSTEM DESCRIPTION > [TYPE 1]
*2: With Intelligent Key
*3: Without Intelligent Key A
*4: With headlamp aiming control system
5
* : With front fog lamp
B
*6: With auto light system
*7: With rear fog lamp
*8: With remote key less entry system (Except for Hong Kong) C

Component Description INFOID:0000000005912271

D
Part Description
• Detects each switch condition by the combination switch reading function
• Judges that the headlamp is turned ON according to the vehicle condition E
• Requests the headlamp relay (HI/LO) ON to IPDM E/R (via CAN communication)
• Requests the high beam indicator lamp, front fog lamp indicator lamp*1 and rear fog
BCM
lamp indicator*2 lamp ON to the combination meter (via CAN communication) F
• Judges the outside brightness from the optical sensor signal*3.
• Judges the ON/OFF status of the exterior lamp from the outside brightness and the
vehicle condition*3.
G
Controls the integrated relay, and supplies voltage to the load according to the request
IPDM E/R
from BCM (using CAN communication)
• Blinks the turn signal indicator lamp and outputs the turn signal operating sound with H
integrated buzzer according to the request from BCM (via CAN communication).
Combination meter • Turns the high beam indicator lamp, tail lamp indicator lamp, front fog lamp indicator
lamp*1 and rear fog lamp indicator lamp*2 ON according to the request from BCM
(via CAN communication). I
Optical sensor converts the outside brightness (lux) to voltage and transmits the optical
Optical sensor
sensor signal to BCM.
The headlamp levelizer adjusts the headlamp light axis upward and downward with the J
Headlamp aiming motor*4 aiming motor integrated in the front combination lamp.

Remote keyless entry receiver*5 Refer to DLK-29, "Component Description"

K
Combination switch Refer to BCS-16, "COMBINATION SWITCH READING SYSTEM : System Descrip-
(Lighting & turn signal switch) tion"

Push-button ignition switch*6 Refer to DLK-29, "Component Description"

EXL
Key switch*7 Refer to DLK-243, "Component Description"

Door request switch*6 Refer to DLK-29, "Component Description"

M
Door switch Refer to DLK-29, "Component Description"
Hazard switch Inputs the hazard switch ON/OFF signal to BCM

Headlamp aiming switch*4 Adjusts height of headlamp aiming. N

*1: With front fog lamp
*2: With rear fog lamp
O
3
* : With auto light system
*4: With headlamp aiming control system
*5: With remote key less entry system P
*6: With Intelligent Key
*7: Without Intelligent Key

EXL-11
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 1]
SYSTEM
HEADLAMP SYSTEM
HEADLAMP SYSTEM : System Diagram INFOID:0000000005912268

JPLIA0167GB

HEADLAMP SYSTEM : System Description INFOID:0000000005912269

OUTLINE
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R using CAN communication according to the head-
lamp (LO) ON condition.
Headlamp (LO) ON condition
- Lighting switch 2ND
- Lighting switch AUTO (auto light function ON judgment)
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
HEADLAMP (HI) OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter using CAN communi-
cation according to the headlamp (HI) ON condition. At this time, BCM stops to transmit low beam request
signal.
Headlamp (HI) ON condition
- Lighting switch HI with the lighting switch 2ND or AUTO (auto light function ON judgment)
- Lighting switch PASS
- Lighting switch AUTO, with the front fog lamp switch ON, the ignition switch ON and lighting switch HI.
• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
FOLLOW ME HOME FUNCTION (FOR INDIA)
When the driver is moving to the house entrance from the own vehicle, headlamp is kept still ON by the follow
me home function of BCM.
• When BCM detects the input of lighting switch PASS while all of following conditions satisfied, it transmits
the low beam request signal for a period of time to IPDM E/R through CAN communication.
Follow me home ON condition
- Ignition switch OFF
- Lighting switch OFF

EXL-12
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 1]
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal. A
• When in any of following conditions, follow me home function can be cancelled while follow me home func-
tion is operating.
Follow me home OFF condition B
- Ignition switch is turned from OFF→ACC or ON
- Lighting switch is turned from OFF→ON
NOTE: C
• Flash-to-pass operation illumination time for 1 time can be extended to approximately 30 seconds during
operation of follow me home function.
• Flash-to-pass operation can be illuminated continuously for approximately 60 seconds (flash-to-pass opera-
tion, 2 times), approximately 90 seconds (flash-to-pass operation, 3 times), and a maximum of approxi- D
mately 120 seconds (flash-to-pass operation, 4 times).
• Follow me home function activating time can be set by CONSULT. Refer to EXL-22, "HEADLAMP : CON-
SULT Function (BCM - HEAD LAMP) (Except India Production For Europe and General Areas)"(with Intelli- E
gent Key), EXL-26, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (Except India Production For
Europe and General Areas)"(without Intelligent Key).
HEADLAMP SYSTEM : Fail-Safe INFOID:0000000006199222 F

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN G
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM
H
Control part Fail-safe operation
• Turns ON the headlamp low relay when the ignition switch is turned ON
Headlamp • Turns OFF the headlamp low relay when the ignition switch is turned OFF I
• Headlamp high relay OFF

AUTO LIGHT SYSTEM (EXCEPT FOR HONG KONG)

J
AUTO LIGHT SYSTEM (EXCEPT FOR HONG KONG) : System Diagram INFOID:0000000006765717

EXL

JMLIA1581GB O

AUTO LIGHT SYSTEM (EXCEPT FOR HONG KONG) : System Description

INFOID:0000000006765718 P

OUTLINE
• Auto light system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function

EXL-13
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 1]
- Auto light function
- Auto light adjustment system
Control by IPDM E/R
- Relay control function
- Auto light function automatically turns ON/OFF the exterior lamps* and each illumination automatically,
depending on the outside brightness.
*: Headlamp (LO/HI), parking lamp, tail lamp and front fog lamp (Headlamp HI and front fog lamp depend on
the combination switch condition.)
AUTO LIGHT FUNCTION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM supplies voltage to optical sensor when the ignition switch is turned ON or ACC.
• Optical sensor converts outside brightness (lux) to voltage and transmits the optical sensor signal to BCM.
• BCM judges outside brightness from the optical sensor signal and judges ON/OFF condition of the exterior
lamp and each illumination according to the outside brightness.
• BCM transmits each request signal to IPDM E/R with CAN communication according to ON/OFF condition
by the auto light function.
NOTE:
ON/OFF timing differs based on the sensitivity from the setting. The setting can be set by CONSULT. Refer to
EXL-22, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (Except India Production For Europe and
General Areas)"(with Intelligent Key), EXL-26, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP)
(Except India Production For Europe and General Areas)"(without Intelligent Key).
AUTO LIGHT ADJUSTMENT SYSTEM
The auto light adjustment system automatically, dims/brightens the display and combination meter, according
to brightness outside the vehicle, when lighting switch 1ST or lighting switch 2ND is operated. Refer to INL-15,
"AUTO LIGHT ADJUSTMENT SYSTEM : System Description".
AUTO LIGHT SYSTEM (FOR HONG KONG)
AUTO LIGHT SYSTEM (FOR HONG KONG) : System Diagram INFOID:0000000006765742

JMLIA1580GB

AUTO LIGHT SYSTEM (FOR HONG KONG) : System Description INFOID:0000000006766769

OUTLINE
• Auto light system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function
- Auto light function
- Wiper linked auto lighting function
- Auto light adjustment system
Control by IPDM E/R
- Relay control function
EXL-14
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 1]
• Auto light system has the auto light function (with twilight lighting function) and wiper linked auto lighting
function. A
- Auto light function automatically turns ON/OFF the exterior lamps* and each illumination automatically,
depending on the outside brightness.
- Wiper linked auto lighting function automatically turns ON/OFF the exterior lamps* and each illumination
B
when the light switch is in the AUTO position, according to a front wiper operation.
*: Headlamp (LO/HI), parking lamp, tail lamp and front fog lamp (Headlamp HI and front fog lamp depend on
the combination switch condition.)
NOTE: C
The settings of the twilight lighting function and the wiper linked auto lighting function can be changed with
CONSULT. Refer to EXL-22, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (Except India Produc-
tion For Europe and General Areas)"(with Intelligent Key), EXL-26, "HEADLAMP : CONSULT Function (BCM - D
HEAD LAMP) (Except India Production For Europe and General Areas)"(without Intelligent Key).
AUTO LIGHT FUNCTION (WITH TWILIGHT LIGHTING FUNCTION)
Description E
• BCM detects the combination switch condition with the combination switch reading function.
• BCM receives vehicle speed signal from combination meter via CAN communication and detects speed and
driving distance of the vehicle. F
• BCM supplies voltage to the optical sensor when the ignition switch is turned ON or ACC.
• Optical sensor converts outside brightness (lux) to voltage and transmits the optical sensor signal to BCM.
• BCM filters outside brightness based on the optical sensor signal and judges outside brightness.
• BCM detects change status of outside brightness according to outside brightness from the optical sensor G
signal and filtered outside brightness. Based on the change status, BCM judges ON/OFF condition of the
exterior lamp.
• BCM transmits each request signal to IPDM E/R via CAN communication, according to ON/OFF condition by H
the auto light function.
NOTE:
As to ON/OFF timing, the sensitivity depends on settings. The settings can be changed with CONSULT. Refer
I
to EXL-22, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (Except India Production For Europe and
General Areas)"(with Intelligent Key), EXL-26, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP)
(Except India Production For Europe and General Areas)"(without Intelligent Key).
J
WIPER LINKED AUTO LIGHTING FUNCTION
BCM turns the exterior lamps ON when detecting 4 operations of the front wiper with the light switch in AUTO
position.
NOTE: K
BCM turns OFF the headlamps 3 seconds after the front wiper switch is turned from HIŸOFF.
AUTO LIGHT ADJUSTMENT SYSTEM
EXL
The auto light adjustment system automatically, dims/brightens the display and combination meter, according
to brightness outside the vehicle, when lighting switch 1ST or lighting switch 2ND is operated. Refer to INL-15,
"AUTO LIGHT ADJUSTMENT SYSTEM : System Description".
HEADLAMP AIMING CONTROL (MANUAL) M

HEADLAMP AIMING CONTROL (MANUAL) : System Description INFOID:0000000006156895

N
The headlamp levelizer adjusts the headlamp light axis upward and downward with the aiming motor inte-
grated in the front combination lamp.
FRONT FOG LAMP SYSTEM O

EXL-15
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 1]
FRONT FOG LAMP SYSTEM : System Diagram INFOID:0000000005912280

JMLIA0970GB

FRONT FOG LAMP SYSTEM : System Description INFOID:0000000006765736

OUTLINE
Front fog lamp is controlled by combination switch reading function and front fog lamp control function of BCM,
and relay control function of IPDM E/R.
FRONT FOG LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front fog light request signal to IPDM E/R and the combination meter via CAN communi-
cation according to the front fog lamp ON condition.
Front fog lamp ON condition
- Front fog lamp switch ON and any of the following.
• Lighting switch 1ST
• Lighting switch 2ND
• Lighting switch AUTO and the ignition switch ON
IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the front
fog light request signal.
Combination meter turns the front fog lamp indicator lamp ON according to the front fog light request signal.
FRONT FOG LAMP SYSTEM : Fail-Safe INFOID:0000000006199224

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM

Control part Fail-safe operation

Front fog lamps Front fog lamp relay OFF

REAR FOG LAMP SYSTEM

EXL-16
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 1]
REAR FOG LAMP SYSTEM : System Diagram INFOID:0000000006173723

E
JPLIA0179GB

REAR FOG LAMP SYSTEM : System Description INFOID:0000000006765739

F

OUTLINE
Rear fog lamp is controlled with the combination switch reading function and the rear fog lamp control function G
of BCM.
REAR FOG LAMP OPERATION H
• BCM detects the condition of the combination switch by the combination switch reading function.
• BCM supplies voltage to rear fog lamp according to the rear fog lamp ON condition.
Rear fog lamp switch is turned from OFF to ON with any of following condition. I
- Lighting switch 2ND
- Lighting switch AUTO and the ignition switch ON
- Front fog lamp ON
• BCM transmits the rear fog lamp status signal to the combination meter using CAN communication. J
• Combination meter turns the rear fog lamp indicator lamp ON according to the rear fog lamp status signal.
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM
K
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram
INFOID:0000000006765876

EXL

P
JPLIA0180GB

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description

INFOID:0000000006765877

OUTLINE

EXL-17
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 1]
Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the
flasher control function of BCM.
TURN SIGNAL LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn
signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION
BCM supplies voltage to both turn signal lamp circuit when the hazard switch is ON. BCM blinks the hazard
warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL OPERATION
• BCM transmits the turn signal indicator lamp signal to the combination meter using CAN communication
while the turn signal lamp and the hazard warning lamp are operating.
• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn signal indicator lamp signal.
HIGH FLASHER OPERATION
• BCM detects the turn signal lamp circuit status from the current value.
• BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn sig-
nal lamp operating.
NOTE:
The blinking speed is normal while operating the hazard warning lamp.
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : System Diagram INFOID:0000000006766794

JMLIA0928GB

PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : System Description

INFOID:0000000006766795

OUTLINE
Parking, license plate and tail lamps are controlled by combination switch reading function and headlamp con-
trol function of BCM, and relay control function of IPDM E/R.
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R via CAN communication according to the ON/
OFF condition of the parking, license plate and tail lamps.
Parking, license plate and tail lamps ON condition
- Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON

EXL-18
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 1]
• IPDM E/R turns the integrated tail lamp relay ON and turns the parking, license plate and tail lamps ON
according to the position light request signal. A
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : Fail-Safe INFOID:0000000006766796

B
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
C
If No CAN Communication Is Available With BCM

Control part Fail-safe operation

D
• Parking lamp
• License plate lamp • Turns ON the tail lamp relay when the ignition switch is turned ON
• Illumination • Turns OFF the tail lamp relay when the ignition switch is turned OFF
• Tail lamp E
EXTERIOR LAMP BATTERY SAVER SYSTEM
EXTERIOR LAMP BATTERY SAVER SYSTEM : System Diagram INFOID:0000000005912292 F

WITH INTELLIGENT KEY SYSTEM

G

K
JMLIA1142GB

WITH REMOTE KEYLESS ENTRY SYSTEM

EXL

P
JMLIA1143GB

EXTERIOR LAMP BATTERY SAVER SYSTEM : System Description INFOID:0000000005912293

OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.

EXL-19
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 1]
Control by BCM
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function
Control by IPDM E/R
- Relay control function
• BCM turns the exterior lamp* OFF, according to the vehicle status when key switch is turned OFF while exte-
rior lamp is ON, for preventing battery discharge.
*: Headlamp (LO/HI), parking lamp, tail lamp, license plate lamp, front fog lamp and rear fog lamp
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM turns the exterior lamps OFF (battery saver is activated) when all of the following conditions are satisfied.
• Ignition switch is OFF position*1.
• Key switch is OFF*2.
• BCM detects door lock signal (auto door lock function, each door request switch*1, remote keyless entry
receiver)
When in any of following conditions (after the exterior lamp battery saver is activated), exterior lamps can be
turned ON.
• Ignition switch is turned from OFF→ON*1
• Key switch is turned from OFF→ON*2
• Front door switch (driver side) is turned from OFF→ON
• Lighting switch is changed
• Front fog lamp switch is changed*3
• Rear fog lamp switch is changed*4
*1: With Intelligent Key
*2: Without Intelligent Key
*3: With front fog lamp
*4: With rear fog lamp

EXL-20
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000006046536
B
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
D
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
Data Monitor The BCM input/output signals are displayed. E
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
• Read and save the vehicle specification. F
Configuration
• Write the vehicle specification when replacing BCM.

SYSTEM APPLICATION
G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item H
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
K

Turn signal and hazard warning lamps FLASHER × × ×

• Automatic air conditioner EXL
AIR CONDITONER × ×*1
• Manual air conditioner
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
M
Combination switch COMB SW ×
Body control system BCM ×
NATS IMMU × × × N
Interior room lamp battery saver BATTERY SAVER × × ×
Back door TRUNK ×
O
Theft warning alarm THEFT ALM × × ×
— RETAINED PWR*2 ×
Signal buffer system SIGNAL BUFFER × × P
NOTE:
• *1: For models with automatic air conditioner, this mode is not used.
• *2: This item is displayed, but is not used.

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.

EXL-21
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]

CONSULT screen item Indication/Unit Description

Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected
While turning BCM status from low power consumption mode to
SLEEP>LOCK
normal mode (Power supply position is “LOCK”)
While turning BCM status from low power consumption mode to
SLEEP>OFF
normal mode (Power supply position is “OFF”.)
LOCK>ACC While turning power supply position from “LOCK” to “ACC”
ACC>ON While turning power supply position from “ACC” to “IGN”
While turning power supply position from “RUN” to “ACC” (Vehicle
RUN>ACC
is stopping and selector lever is except P position.)
While turning power supply position from “CRANKING” to “RUN”
CRANK>RUN
(From cranking up the engine to run it)
While turning power supply position from “RUN“ to “ACC” (Emer-
RUN>URGENT
gency stop operation)
ACC>OFF While turning power supply position from “ACC” to “OFF”
OFF>LOCK While turning power supply position from “OFF” to “LOCK”
Power position status of
OFF>ACC While turning power supply position from “OFF” to “ACC”
Vehicle Condition the moment a particular
ON>CRANK DTC is detected While turning power supply position from “IGN” to “CRANKING”
While turning BCM status from normal mode (Power supply posi-
OFF>SLEEP
tion is “OFF”.) to low power consumption mode
While turning BCM status from normal mode (Power supply posi-
LOCK>SLEEP
tion is “LOCK”.) to low power consumption mode
Power supply position is “LOCK” (Ignition switch OFF with steer-
LOCK
ing is locked.)
Power supply position is “OFF” (Ignition switch OFF with steering
OFF
is unlocked.)
ACC Power supply position is “ACC” (Ignition switch ACC)
Power supply position is “IGN” (Ignition switch ON with engine
ON
stopped)
Power supply position is “RUN” (Ignition switch ON with engine
ENGINE RUN
running)
CRANKING Power supply position is “CRANKING” (At engine cranking)
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
IGN Counter 0 - 39 • The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (Except India Production For
Europe and General Areas) INFOID:0000000005912297

WORK SUPPORT

Service item Setting item Setting

On* With the exterior lamp battery saver function

BATTERY SAVER SET
Off Without the exterior lamp battery saver function
MODE 1 10 sec.
HEAD LIGHT TIMER*1 Sets follow me home function activating time
MODE 2* 30 sec.

EXL-22
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
Service item Setting item Setting
A
MODE 1*4 With twilight ON custom & with wiper INT, LO and HI
MODE 2 With twilight ON custom & with wiper LO and HI
MODE 3 With twilight ON custom & without B
AUTO LIGHT LOGIC SET*2
MODE 4 Without twilight ON custom & with wiper INT, LO and HI
MODE 5 Without twilight ON custom & with wiper LO and HI
C
MODE 6 Without twilight ON custom & without

MODE 1*4 Normal

MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal op- D
CUSTOM A/LIGHT SET- eration)
TING*3 MODE 3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)
Less sensitive setting than normal setting (Turns ON later than normal opera- E
MODE 4
tion)

*1: For models for India, this item is operated.

F
*2: For models for Hong Kong, this item is operated.
*3: For models with auto light system, this item is operated.
*4: Factory setting
G
DATA MONITOR

Monitor item
Description
H
[Unit]
PUSH SW
The switch status input from push-button ignition switch
[On/Off]
I
ENGINE STATE
The engine status received from ECM using CAN communication
[Stop/Stall/Crank/Run]
VEH SPEED 1 The value of the vehicle speed received from combination meter using CAN commu- J
[km/h] nication
TURN SIGNAL R
[On/Off]
K
TURN SIGNAL L
[On/Off]
TAIL LAMP SW EXL
[On/Off]
HI BEAM SW
[On/Off]
M
HEAD LAMP SW1
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW2
[On/Off]
N

PASSING SW
[On/Off]
O
AUTO LIGHT SW*1
[On/Off]

FR FOG SW*2 P
[On/Off]

RR FOG SW*3
[On/Off]
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]

EXL-23
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
Monitor item
Description
[Unit]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW-RL
The switch status input from rear door switch LH
[On/Off]
DOOR SW-BK
The switch status input from back door switch
[On/Off]

OPTICAL SENSOR*1 NOTE:

[On/Off/NG] This item is indicated, but can not monitored

OPTI SEN (DTCT)*1 The value of outside brightness voltage input from the optical sensor
[V]

OPTI SEN (FILT)*1 The value of outside brightness voltage filtered by BCM
[V]

*1: For models with auto light system, this item is displayed.
*2: For models with front fog lamp system, this item is monitored.
*3: For models with rear fog lamp system, this item is monitored.
ACTIVE TEST

Test item Operation Description

Transmits the position light request signal to IPDM E/R using CAN com-
On
TAIL LAMP munication to turn the tail lamp ON
Off Stops the tail lamp request signal transmission
Transmits the high beam request signal using CAN communication to
Hi
turn the headlamp (HI)
HEAD LAMP Transmits the low beam request signal using CAN communication to turn
Lo
the headlamp (LO)
Off Stops the high & low beam request signal transmission
Transmits the front fog lights request signal to IPDM E/R using CAN
On
FR FOG LAMP*1 communication to turn the front fog lamp ON
Off Stops the front fog lights request signal transmission
• Outputs voltage to turn the rear fog lamp ON
On • Transmits the rear fog lights request signal to combination meter using
RR FOG LAMP*2 CAN communication to turn the rear fog lamp indicator lamp ON
• Stops the voltage to turn the rear fog lamp OFF
Off
• Stops the rear fog lamp status signal transmission
Transmits the dimmer signal to combination meter via CAN communica-
On
ILL DIM SIGNAL*3 tion and dims display in combination meter
Off Stops the dimmer signal transmission

*1: For models with front fog lamp system, this item is tested.
*2: For models with rear fog lamp system, this item is tested.
*3: For models for Hong kong, this item is tested.
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) (Except India Production For Eu-
rope and General Areas) INFOID:0000000005912298

WORK SUPPORT

EXL-24
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]

Service item Setting item Setting A

Lock Only With locking only
Unlk Only With unlocking only Sets the hazard warning lamp answer back function
HAZARD ANSWER
when the door is lock/unlock with the door request switch B
BACK Lock/Unlk* With locking/unlocking and the Intelligent Key.
Off Without the function
*: Factory setting C
DATA MONITOR

Monitor item D
Description
[Unit]
REQ SW-DR
The switch status input from the request switch (driver side)
[On/Off] E
REQ SW-AS
The switch status input from the request switch (passenger side)
[On/Off]
PUSH SW F
The switch status input from the push-button ignition switch
[On/Off]
TURN SIGNAL R
[On/Off] G
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW H
The switch status input from the hazard switch
[On/Off]
RKE-LOCK
Lock signal status received from the remote keyless entry receiver
[On/Off] I
RKE-UNLOCK
Unlock signal status received from the remote keyless entry receiver
[On/Off]
RKE-PANIC*
Panic alarm signal status received from the remote keyless entry receiver
J
[On/Off]
*: For models with panic alarm system, this item is monitored.
ACTIVE TEST K

Test item Operation Description

EXL
RH Outputs the voltage to blink the right side turn signal lamps.
FLASHER LH Outputs the voltage to blink the left side turn signal lamps.
Off Stops the voltage to turn the turn signal lamps OFF. M

EXL-25
 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000006046537

APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.

Diagnosis mode Function Description

Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing BCM.

SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
• Automatic air conditioner
AIR CONDITONER ×
• Manual air conditioner
Combination switch COMB SW ×
Body control system BCM ×
NATS IMMU ×
Interior room lamp battery saver BATTERY SAVER × ×
Back door TRUNK ×
Theft warning alarm THEFT ALM*1 × ×

— RETAINED PWR*2
Signal buffer system SIGNAL BUFFER × ×
Panic alarm PANIC ALARM ×

• *1: For models without theft warning alarm this mode is not used.
• *2: This item is displayed, but is not used.
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (Except India Production For

EXL-26
 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
Europe and General Areas) INFOID:0000000005969677

A
WORK SUPPORT

Service item Setting item Setting B

On*4 With the exterior lamp battery saver function
BATTERY SAVER SET*1
Off Without the exterior lamp battery saver function
C
MODE 1*4 Normal
More sensitive setting than normal setting (Turns ON earlier than normal op-
MODE 2
CUSTOM A/LIGHT SET- eration) D
TING*2 MODE 3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)
Less sensitive setting than normal setting (Turns ON later than normal oper-
MODE 4 E
ation)
MODE 1
MODE 2
F
MODE 3 NOTE:
AUTO LIGHT LOGIC SET
MODE 4 The item is displayed, but cannot be used

MODE 5 G
MODE 6
MODE 1 10 sec.
HEAD LIGHT TIMER*3 Sets follow me home function activating time H
MODE 2* 30 sec.

*1: For models with remote keyless entry system, this item is operated.
*2: For models with auto light system, this item is displayed. I
*3: For models for India, this item is operated.
*4
: Factory setting
J
DATA MONITOR

Monitor item
Description K
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
EXL
ACC ON SW
Ignition switch (ACC) status judged from ACC signal (ACC power supply)
[On/Off]
VEH SPEED The value of the vehicle speed received from combination meter using CAN commu-
[km/h] nication M
HI BEAM SW
[On/Off]
N
HEAD LAMP SW1
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW2
[On/Off] O
PASSING SW
[On/Off]
FR FOG SW NOTE: P
[On/Off] The item is indicated, but not monitored

AUTO LIGHT SW*1

[On/Off]
Each switch status that BCM judges from the combination switch reading function
RR FOG SW*2
[On/Off]

EXL-27
 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
Monitor item
Description
[Unit]
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL
The switch status input from rear door switch LH
[On/Off]
BACK DOOR SW
The switch status input from back door switch
[On/Off]
TURN SIGNAL R
[On/Off]
TURN SIGNAL L
Each switch status that BCM judges from the combination switch reading function
[On/Off]
TAIL LAMP SW
[On/Off]
KEY ON SW
The switch status input from key on switch
[On/Off]

KEYLESS LOCK*3 Lock signal status received from remote keyless entry receiver (integrated in the
[On/Off] BCM)
PKB SW The parking brake switch status received from combination meter using CAN com-
[On/Off] munication
ENGINE RUN
The engine status received from ECM using CAN communication
[On/Off]

OPTI SEN (DTCT)*1 The value of outside brightness voltage input from the optical sensor
[V]

OPTI SEN (FILT)*1 The value of outside brightness voltage filtered by BCM
[V]

*1: For models with auto light system, this item is monitored.
*2
: For models with rear fog lamp system, this item is monitored.
*3
: For models without power door lock system this item is not displayed. For models without remote keyless
entry system this item is displayed but not monitored.
ACTIVE TEST

Test item Operation Description

Transmits the position light request signal to IPDM E/R using CAN com-
On
TAIL LAMP munication to turn the tail lamp ON
Off Stops the tail lamp request signal transmission
Transmits the high beam request signal using CAN communication to
Hi
turn the headlamp (HI)
HEAD LAMP Transmits the low beam request signal using CAN communication to turn
Lo
the headlamp (LO)
Off Stops the high & low beam request signal transmission
Transmits the front fog lights request signal to IPDM E/R using CAN
On
FR FOG LAMP* 1 communication to turn the front fog lamp ON
Off Stops the front fog lights request signal transmission

EXL-28
 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
Test item Operation Description
A
• Outputs voltage to turn the rear fog lamp ON
On • Transmits the rear fog lights request signal to combination meter using
RR FOG LAMP*2 CAN communication to turn the rear fog lamp indicator lamp ON
• Stops the voltage to turn the rear fog lamp OFF B
Off
• Stops the rear fog lamp status signal transmission
Transmits the dimmer signal to combination meter via CAN communica-
On
ILL DIM SIGNAL*3 tion and dims display in combination meter C
Off Stops the dimmer signal transmission

*1: For models with front fog lamp system, this item is tested.
D
*2: For models with rear fog lamp system, this item is tested.
*3: For models for Hong Kong, this item is tested.
FLASHER E

FLASHER : CONSULT Function (BCM - FLASHER) (Except India Production For Eu-
rope and General Areas) INFOID:0000000005969678
F

DATA MONITOR
G
Monitor item
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply) H
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function I
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch J
[On/Off]

ACTIVE TEST
K
Test item Operation Description
RH Outputs the voltage to blink the right side turn signal lamps.
FLASHER LH Outputs the voltage to blink the left side turn signal lamps. EXL
Off Stops the voltage to turn the turn signal lamps OFF.

EXL-29
 DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
Diagnosis Description INFOID:0000000006046538

AUTO ACTIVE TEST

Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Front wiper (LO, HI)
• Parking lamp
• License plate lamp
• Tail lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
NOTE:
Never perform auto active test in the following conditions.
• CONSULT is connected
• Passenger door is open
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
NOTE:
• Engine starts when ignition switch is turned ON while brake pedal is depressed.
• Only a vehicle with the vehicle security system, the horn sounds.
5. The oil pressure warning lamp starts blinking when the auto active test starts.
6. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK-114,
"Component Function Check".
Inspection in Auto Active Test
When auto active test is actuated, the following operation sequence is repeated 3 times.

Operation
Inspection location Operation
sequence
1 Oil pressure warning lamp Blinks continuously during operation of auto active test
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamp
• License plate lamp
3 10 seconds
• Tail lamp
• Front fog lamp
4 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
6 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds

EXL-30
 DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
Concept of Auto Active Test
A

JMMIA0354GB F
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated. G

Diagnosis Chart in Auto Active Test

H
Symptom Inspection contents Possible cause
Any of the following components do not operate YES BCM signal input circuit
• Parking lamp
• License plate lamp Perform auto active test. • Lamp or motor I
• Tail lamp Does the applicable system • Lamp or motor ground circuit
• Front fog lamp operate? NO • Harness or connector between
• Headlamp (HI, LO) IPDM E/R and applicable system
• IPDM E/R J
• Front wiper (HI, LO)
• BCM signal input circuit
• CAN communication signal be-
YES tween BCM and ECM K
Perform auto active test. • CAN communication signal be-
A/C compressor does not operate Does the magnet clutch oper- tween ECM and IPDM E/R
ate? • Magnet clutch EXL
• Harness or connector between
NO
IPDM E/R and magnet clutch
• IPDM E/R
M
• Harness or connector between
IPDM E/R and oil pressure switch
YES
• Oil pressure switch
• IPDM E/R N
Perform auto active test.
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal be-
lamp blink? tween IPDM E/R and BCM
• CAN communication signal be-
NO
tween BCM and combination
O
meter
• Combination meter
• ECM signal input circuit P
YES • CAN communication signal be-
tween ECM and IPDM E/R
Perform auto active test.
Cooling fan does not operate • Cooling fan motor
Does the cooling fan operate?
• Harness or connector between
NO
IPDM E/R and cooling fan motor
• IPDM E/R

EXL-31
 DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
CONSULT Function (IPDM E/R) INFOID:0000000006046539

APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.

Diagnosis mode Description

Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.

SELF DIAGNOSTIC RESULT

Refer to PCS-39, "DTC Index".
DATA MONITOR
Monitor item

Monitor Item MAIN SIG-

Description
[Unit] NALS
MOTOR FAN REQ Displays the value of the cooling fan speed request signal received from ECM via
×
[1/2/3/4] CAN communication.
AC COMP REQ Displays the status of the A/C compressor request signal received from ECM via
×
[Off/On] CAN communication.
TAIL&CLR REQ Displays the status of the position light request signal received from BCM via CAN
×
[Off/On] communication.
HL LO REQ Displays the status of the low beam request signal received from BCM via CAN
×
[Off/On] communication.
HL HI REQ Displays the status of the high beam request signal received from BCM via CAN
×
[Off/On] communication.
FR FOG REQ Displays the status of the front fog light request signal received from BCM via CAN
×
[Off/On] communication.
FR WIP REQ Displays the status of the front wiper request signal received from BCM via CAN
×
[Stop/1LOW/Low/Hi] communication.
WIP AUTO STOP
× Displays the status of the front wiper stop position signal judged by IPDM E/R.
[STOP P/ACT P]
WIP PROT
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[Off/BLOCK]
IGN RLY1 -REQ Displays the status of the ignition switch ON signal received from BCM via CAN
[Off/On] communication.
IGN RLY
× Displays the status of the ignition relay judged by IPDM E/R.
[Off/On]
PUSH SW
Displays the status of the push-button ignition switch judged by IPDM E/R.
[Off/On]
INTER/NP SW
Displays the status of the shift position judged by IPDM E/R.
[Off/On]
ST RLY CONT Displays the status of the starter relay status signal received from BCM via CAN
[Off/On] communication.
IHBT RLY -REQ Displays the status of the starter control relay signal received from BCM via CAN
[Off/On] communication.
ST/INHI RLY Displays the status of the starter relay and starter control relay judged by IPDM E/
[Off/ ST ON/INHI ON/UNKWN] R.
DETENT SW Displays the status of the A/T shift selector (detention switch)* judged by IPDM E/
[Off/On] R.

EXL-32
 DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
Monitor Item MAIN SIG-
Description
[Unit] NALS A
S/L RLY -REQ Displays the status of the steering lock relay signal received from BCM via CAN
[Off/On] communication.
S/L STATE B
Displays the status of the steering lock judged by IPDM E/R.
[LOCK/UNLK/UNKWN]
DTRL REQ Displays the status of the daytime running light request signal received from BCM
[Off/On] via CAN communication. C
OIL P SW
Displays the status of the oil pressure switch judged by IPDM E/R.
[Open/Close]
HOOD SW D
Displays the status of the hood switch judged by IPDM E/R.
[Off/On]
HL WASHER REQ NOTE:
[Off/On] This item is indicated, but not monitored. E
THFT HRN REQ Displays the status of the theft warning horn request signal received from BCM via
[Off/On] CAN communication.
HORN CHIRP NOTE: F
[Off/On] This item is indicated, but not monitored.
*: CVT shift selector (detention switch) for CVT models.
ACTIVE TEST G
Test item

Test item Operation Description H

HORN On Operates horn relay for 20 ms.
Off OFF
I
FRONT WIPER Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.
1 OFF J
2 Operates the cooling fan relay (LO operation).
MOTOR FAN
3 Operates the cooling fan relay (MID operation).
K
4 Operates the cooling fan relay (HI operation).
NOTE:
HEAD LAMP WASHER Off
This item is indicated, but cannot be tested.
EXL
Off OFF
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay. M
EXTERNAL LAMPS
Operates simultaneously the headlamp low relay and the headlamp high relay
Hi
at 1 second ON/OFF intervals.
Fog Operates the front fog lamp relay. N

EXL-33
 DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYS-
TEM)
Diagnosis Description INFOID:0000000006046540

AUTO ACTIVE TEST

Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Front wiper (LO, HI)
• Parking lamp
• License plate lamp
• Tail lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
NOTE:
Never perform auto active test in the following conditions.
• CONSULT is connected
• Passenger door is open
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
NOTE:
Only a vehicle with the vehicle security system, the horn sounds.
5. The oil pressure warning lamp starts blinking when the auto active test starts.
6. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK-284,
"Component Function Check".
Inspection in Auto Active Test
When auto active test is actuated, the following operation sequence is repeated 3 times.

Operation
Inspection location Operation
sequence
1 Oil pressure warning lamp Blinks continuously during operation of auto active test
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamp
3 • License plate lamp 10 seconds
• Tail lamp
4 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
6 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds

EXL-34
 DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
Concept of Auto Active Test
A

JMMIA0355GB F
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated. G

Diagnosis chart in auto active test mode

H
Symptom Inspection contents Possible cause

Any of the following components do not operate YES BCM signal input circuit
• Parking lamp • Lamp or motor
Perform auto active test. I
• License plate lamp • Lamp or motor ground circuit
Does the applicable system
• Tail lamp NO • Harness or connector between
operate?
• Headlamp (HI, LO) IPDM E/R and applicable system
• Front wiper (HI, LO) • IPDM E/R J
• BCM signal input circuit
• CAN communication signal be-
YES tween BCM and ECM K
Perform auto active test. • CAN communication signal be-
A/C compressor does not operate Does the magnet clutch oper- tween ECM and IPDM E/R
ate? • Magnet clutch
• Harness or connector between EXL
NO
IPDM E/R and magnet clutch
• IPDM E/R
• Harness or connector between M
IPDM E/R and oil pressure
YES switch
• Oil pressure switch
• IPDM E/R N
Perform auto active test.
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal be-
lamp blink? tween IPDM E/R and BCM
NO
• CAN communication signal be- O
tween BCM and combination
meter
• Combination meter
P
• ECM signal input circuit
YES • CAN communication signal be-
tween ECM and IPDM E/R
Perform auto active test.
Cooling fan does not operate • Cooling fan motor
Does the cooling fan operate?
• Harness or connector between
NO
IPDM E/R and cooling fan motor
• IPDM E/R

EXL-35
 DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
CONSULT Function (IPDM E/R) INFOID:0000000006046541

APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.

Diagnosis mode Description

Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.

SELF DIAGNOSTIC RESULT

Refer to PCS-105, "DTC Index".
DATA MONITOR
Monitor item

Monitor Item MAIN SIG-

Description
[Unit] NALS
MOTOR FAN REQ Displays the value of the cooling fan speed request signal received from ECM via
×
[1/2/3/4] CAN communication.
AC COMP REQ Displays the status of the A/C compressor request signal received from ECM via
×
[Off/On] CAN communication.
TAIL&CLR REQ Displays the status of the position light request signal received from BCM via CAN
×
[Off/On] communication.
HL LO REQ Displays the status of the low beam request signal received from BCM via CAN
×
[Off/On] communication.
HL HI REQ Displays the status of the high beam request signal received from BCM via CAN
×
[Off/On] communication.
FR FOG REQ Displays the status of the front fog light request signal received from BCM via CAN
×
[Off/On] communication.
FR WIP REQ Displays the status of the front wiper request signal received from BCM via CAN
×
[Stop/1LOW/Low/Hi] communication.
WIP AUTO STOP
× Displays the status of the front wiper stop position signal judged by IPDM E/R.
[STOP P/ACT P]
WIP PROT
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[Off/BLOCK]
IGN RLY
× Displays the status of the ignition relay judged by IPDM E/R.
[Off/On]
INTER/NP SW
Displays the status of the shift position judged by IPDM E/R.
[Off/On]
ST RLY REQ Displays the status of the starter control relay signal received from BCM via CAN
[Off/On] communication.
DTRL REQ Displays the status of the daytime running light request signal received from BCM
[Off/On] via CAN communication.
OIL P SW
Displays the status of the oil pressure switch judged by IPDM E/R.
[Open/Close]
HOOD SW
Displays the status of the hood switch judged by IPDM E/R.
[Off/On]
HL WASHER REQ NOTE:
[Off/On] This item is indicated, but not monitored.
THFT HRN REQ Displays the status of the theft warning horn request signal received from BCM via
[Off/On] CAN communication.

EXL-36
 DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 1]
Monitor Item MAIN SIG-
Description
[Unit] NALS A
HORN CHIRP NOTE:
[Off/On] This item is indicated, but not monitored.
CRNRNG LMP REQ NOTE: B
[Off/On] This item is indicated, but not monitored.

ACTIVE TEST C
Test item

Test item Operation Description

D
HORN On Operates horn relay for 20 ms.
Off OFF
FRONT WIPER Lo Operates the front wiper relay. E
Hi Operates the front wiper relay and front wiper high relay.
1 OFF
2 Operates the cooling fan relay (LO operation).
F
MOTOR FAN
3 Operates the cooling fan relay (MID operation).
4 Operates the cooling fan relay (HI operation). G
NOTE:
HEAD LAMP WASHER Off
This item is indicated, but cannot be tested.
Off OFF H
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates simultaneously the headlamp low relay and the headlamp high relay at
I
Hi
1 second ON/OFF intervals.
Fog Operates the front fog lamp relay.
J

EXL

EXL-37
 BCM, IPDM E/R
< ECU DIAGNOSIS INFORMATION > [TYPE 1]

ECU DIAGNOSIS INFORMATION

BCM, IPDM E/R
List of ECU Reference INFOID:0000000005912390

WITH INTELLIGENT KEY

ECU Reference
BCS-57, "Reference Value (Type A)" *
BCS-79, "Reference Value (Type B)" *
BCM BCS-149, "Fail-safe"
BCS-152, "DTC Inspection Priority Chart"
BCS-153, "DTC Index"
PCS-19, "Reference Value"
IPDM E/R PCS-38, "Fail-Safe"
PCS-39, "DTC Index"
*: Regarding to the vehicle type, refer to BCS-57, "Application Notice".
WITHOUT INTELLIGENT KEY

ECU Reference
BCS-242, "Reference Value (Type A)" *
BCS-256, "Reference Value (Type B)" *
BCM BCS-301, "Fail-safe"
BCS-302, "DTC Inspection Priority Chart"
BCS-302, "DTC Index"
PCS-86, "Reference Value"
IPDM E/R PCS-104, "Fail-Safe"
PCS-105, "DTC Index"
*: Regarding to the vehicle type, refer to BCS-242, "Application Notice".

EXL-38
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

WIRING DIAGRAM A
EXTERIOR LIGHTING SYSTEM
Application Notice INFOID:0000000006881752
B

Wiring diagram type Destination

C
• Models for Thailand
TYPE A • Models for General area from Thailand plant*
• Models for China
• Models for India (HR12DE engine models): Vehicle production: From May 2010 to April 2011 D
• Models for Australia
• Models for New Zealand
TYPE B • Models for Hong Kong E
• Models for India (K9K engine models): Vehicle production: From October 2010 to April 2011
• Models for general area from India plant*
TYPE C Models for India: Vehicle production: From May 2011 F
*: Refer to GI-26, "Information About Identification or Model Code", “Information About Identification or Model
Code” to identify a production plant.
TYPE A G

EXL

EXL-39
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]
TYPE A : Wiring Diagram INFOID:0000000006081220

JCLWM5542GB

EXL-40
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM5543GB

EXL-41
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM5544GB

EXL-42
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM5545GB

EXL-43
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM5546GB

EXL-44
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM5547GB

EXL-45
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM5548GB

EXL-46
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM5549GB

EXL-47
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM5550GB

EXL-48
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM5551GB

EXL-49
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM5552GB

EXL-50
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM5553GB

EXL-51
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM5554GB

EXL-52
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM5555GB

EXL-53
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM5556GB

EXL-54
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM5557GB

TYPE B P

EXL-55
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]
TYPE B : Wiring Diagram INFOID:0000000006881760

JCLWM6031GB

EXL-56
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM6032GB

EXL-57
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM6033GB

EXL-58
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM6034GB

EXL-59
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM6035GB

EXL-60
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM6036GB

EXL-61
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM6037GB

EXL-62
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM6038GB

EXL-63
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM6039GB

EXL-64
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM6040GB

EXL-65
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM6041GB

EXL-66
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM6042GB

EXL-67
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM6043GB

EXL-68
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM6044GB

EXL-69
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM6045GB

EXL-70
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM6046GB

EXL-71
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JCLWM6047GB

EXL-72
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JCLWM6048GB

TYPE C P

EXL-73
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]
TYPE C : Wiring Diagram INFOID:0000000007640988

For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not
described in wiring diagram), refer to GI-12, "Connector Information".

JRLWC0713GB

EXL-74
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JRLWC0714GB

EXL-75
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JRLWC0715GB

EXL-76
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

EXL

JRLWC0716GB

EXL-77
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 1]

JRLWC0717GB

EXL-78
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [TYPE 1]

BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000007618859
B

OVERALL SEQUENCE
C

EXL

JMKIA8652GB

DETAILED FLOW

EXL-79
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [TYPE 1]

1.GET INFORMATION FOR SYMPTOM

1. Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2. Check operation condition of the function that is malfunctioning.

>> GO TO 2.
2.CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is detected.
- Record DTC and freeze frame data (Print them out using CONSULT.)
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 5.
4.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to BCS-152, "DTC Inspection Priority Chart" [BCM (with Intelligent
Key)], BCS-302, "DTC Inspection Priority Chart" [BCM (without Intelligent Key)] and determine trouble diag-
nosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES >> GO TO 7.
NO >> Check according to GI-51, "Intermittent Incident".
6.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES >> GO TO 7.
NO >> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.

EXL-80
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [TYPE 1]

7.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE A

Inspect according to Diagnostic Procedure of the system.
Is malfunctioning part detected?
YES >> GO TO 8. B
NO >> Check according to GI-51, "Intermittent Incident".
8.REPAIR OR REPLACE THE MALFUNCTIONING PART
C
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is detected, erase it. D

>> GO TO 9.
E
9.FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely. F
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
G
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO >> Before returning the vehicle to the customer, always erase DTC.
H

EXL

EXL-81
 EXTERIOR LAMP FUSE
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]

DTC/CIRCUIT DIAGNOSIS
EXTERIOR LAMP FUSE
Diagnosis Procedure INFOID:0000000005912408

1.CHECK FUSE
Check that the following fuses are not fusing.

Unit Location Fuse No. Capacity

Headlamp HI (LH) IPDM E/R #45 10 A
Headlamp HI (RH) IPDM E/R #44 10 A
Headlamp LO (LH) IPDM E/R #42 15 A
Headlamp LO (RH) IPDM E/R #41 15 A
Front fog lamp — #39 15 A
• Parking lamp
• Tail lamp IPDM E/R #46 10 A
• License plate lamp
Stop lamp Fuse and fusible link block #38 10 A
IPDM E/R 1 10 A
#52*
Back-up lamp #5*2
— 10 A
#63*3

*1: For A/T models

*2: For M/T models
*3: For CVT models
Is the inspection result normal?
YES >> The fuse is normal.
NO >> Repair the applicable circuit. And then replace the fuse.

EXL-82
 HEADLAMP (HI) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
HEADLAMP (HI) CIRCUIT
A
Component Function Check INFOID:0000000005912411

1.CHECK HEADLAMP (HI) OPERATION B

CONSULT ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the headlamp (HI) is turned ON. C

Hi : Headlamp (HI) ON
Off : Headlamp (HI) OFF D
NOTE:
ON/OFF is repeated 1 second each.
E
Is the inspection result normal?
YES >> Headlamp (HI) circuit is normal.
NO >> Refer to EXL-83, "Diagnosis Procedure".
F
Diagnosis Procedure INFOID:0000000005912412

1.CHECK HEADLAMP (HI) OUTPUT VOLTAGE G

CONSULT ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect headlamp connector. H
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5. With operating the test items, check voltage between IPDM E/R harness connector and ground.
I
(+)
Voltage
IPDM E/R (−) Test item
(Approx.) J
Connector Terminal

RH Hi Battery voltage
63
Off 0V K
E14 Ground EXTERNAL LAMPS
LH Hi Battery voltage
61
Off 0V
EXL
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
M
2.CHECK HEADLAMP (HI) OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector. N
3. Check continuity between IPDM E/R harness connector and headlamp harness connector.

IPDM E/R Headlamp O

Continuity
Connector Terminal Connector Terminal
RH 63 E45
E14 1 Existed
LH 61 E26 P
Is the inspection result normal?
YES >> Replace headlamp bulb.
NO >> Repair or replace harness.
3.CHECK HEADLAMP (HI) FUSE
1. Turn ignition switch OFF.

EXL-83
 HEADLAMP (HI) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
2. Check that the following fuses are not fusing.

Unit Location Fuse No. Capacity

Headlamp HI (RH) #44
IPDM E/R 10 A
Headlamp HI (LH) #45
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> GO TO 4.
4.CHECK HEADLAMP HIGH (HI) SHORT CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R
Continuity
Connector Terminal
Ground
RH 63
E14 Not existed
LH 61
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.

EXL-84
 HEADLAMP (LO) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
HEADLAMP (LO) CIRCUIT
A
Component Function Check INFOID:0000000005912413

1.CHECK HEADLAMP (LO) OPERATION B

CONSULT ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the headlamp (LO) is turned ON. C

Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF D
Is the inspection result normal?
YES >> Headlamp (LO) is normal.
E
NO >> Refer to EXL-85, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000005912415

F
1.CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1. Turn ignition switch OFF. G
2. Disconnect headlamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item. H
5. With operating the test items, check voltage between IPDM E/R harness connector and ground.

(+)
(−) Voltage I
IPDM E/R Test item
(Approx.)
Connector Terminal
Lo Battery voltage J
RH 40
Off 0V
E12 Ground EXTERNAL LAMPS
38*1 Lo Battery voltage
LH 2 K
39* Off 0V

*1: Without Stop/Start system

*2: With Stop/Start system EXL
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3. M
2.CHECK HEADLAMP (LO) OPEN CIRCUIT
1. Turn ignition switch OFF.
N
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector.

IPDM E/R Headlamp O

Continuity
Connector Terminal Connector Terminal
RH 40 E45
P
E12 38* 1 3 Existed
LH E26
39*2

*1: Without Stop/Start system

*2: With Stop/Start system
Is the inspection result normal?
YES >> Replace headlamp bulb.

EXL-85
 HEADLAMP (LO) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
NO >> Repair or replace harness.
3.CHECK HEADLAMP (LO) FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.

Unit Lotion Fuse No. Capacity

Headlamp LO (RH) #41
IPDM E/R 15 A
Headlamp LO (LH) #42
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> GO TO 4.
4.CHECK HEADLAMP (LO) SHORT CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R
Continuity
Connector Terminal
RH 40 Ground
E12 38* 1 Not existed
LH
39*2

*1: Without Stop/Start system

*2: With Stop/Start system
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.

EXL-86
 HEADLAMP GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
HEADLAMP GROUND CIRCUIT
A
Diagnosis Procedure INFOID:0000000006274432

1.CHECK HEADLAMP GROUND OPEN CIRCUIT B

1. Turn ignition switch OFF.
2. Disconnect headlamp connector.
3. Check continuity between headlamp harness connector and ground. C

Headlamp
Continuity
Connector Terminal D
Ground
RH E45
2 Existed
LH E26
E
Is the inspection result normal?
YES >> Headlamp ground circuit is normal.
NO >> Repair or replace harness.
F

EXL

EXL-87
 HEADLAMP AIMING SYSTEM (MANUAL)
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
HEADLAMP AIMING SYSTEM (MANUAL)
Component Inspection INFOID:0000000006156938

1.CHECK HEADLAMP AIMING SWITCH

1. Remove headlamp aiming switch.
2. Check resistance among each headlamp aiming switch terminal.

Headlamp aiming switch Condition Resistance

Terminal Switch position (Approx.)

0 A: 1000 Ω
1 B: 511 Ω
2
1 2 C: 348 Ω
3 D: 240 Ω
3 — E: 390 Ω JSLIA0084ZZ

Is the inspection result normal?

YES >> Headlamp aiming switch is normal.
NO >> Replace the headlamp aiming switch.

EXL-88
 PARKING LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
PARKING LAMP CIRCUIT
A
Component Function Check INFOID:0000000005912422

1.CHECK PARKING LAMP OPERATION B

CONSULT ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the parking lamp is turned ON. C

TAIL : Parking lamp ON

Off : Parking lamp OFF D
Is the inspection result normal?
YES >> Parking lamp circuit is normal.
E
NO >> Refer to EXL-89, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000005912423

F
1.CHECK PARKING LAMP FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing. G

Unit Location Fuse No. Capacity

• Parking lamp H
• Tail lamp IPDM E/R #46 10 A
• License plate lamp
Is the inspection result normal? I
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK PARKING LAMP SHORT CIRCUIT J
1. Disconnect the following connectors.
- IPDM E/R
- Parking lamp K
- Rear combination lamp
- License plate lamp
2. Check continuity between IPDM E/R harness connector and ground. EXL

IPDM E/R
Continuity
Connector Terminal Ground M
E14 59 Not existed
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if fusing is found again.) N
NO >> Repair or replace harness. And then replace the fuse.
3.CHECK PARKING LAMP BULB O
Check the applicable lamp bulb.
Is the bulb normal?
YES >> GO TO 4. P
NO >> Replace the bulb.
4.CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1. Disconnect parking lamp connector.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.

EXL-89
 PARKING LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
4. With operating the test items, check voltage between IPDM E/R harness connector and ground.

(+)
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal

EXTERNAL TAIL Battery voltage

E14 59 Ground
LAMPS OFF 0V
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace IPDM E/R.
5.CHECK PARKING LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and parking lamp harness connector.

IPDM E/R Parking lamp

Continuity
Connector Terminal Connector Terminal
RH E43
E14 59 1 Existed
LH E24
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between parking lamp harness connector and ground.

Parking lamp
Continuity
Connector Terminal
Ground
RH E43
2 Existed
LH E24
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.

EXL-90
 TAIL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
TAIL LAMP CIRCUIT
A
Component Function Check INFOID:0000000005912432

1.CHECK PARKING LAMP OPERATION B

Check that the parking lamp is turned ON.
Is the inspection result normal?
C
YES >> GO TO 2.
NO >> Refer to EXL-89, "Component Function Check".
2.CHECK TAIL LAMP OPERATION D
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the tail lamp is turned ON.
E
TAIL : Tail lamp ON
Off : Tail lamp OFF
Is the inspection result normal? F
YES >> Tail lamp circuit is normal.
NO >> Refer to EXL-91, "Diagnosis Procedure".
G
Diagnosis Procedure INFOID:0000000005912433

1.CHECK TAIL LAMP BULB H

Check the applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 2. I
NO >> Replace bulb.
2.CHECK TAIL LAMP OPEN CIRCUIT
J
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and rear combination lamp connector.
3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
K
IPDM E/R Rear combination lamp
Continuity
Connector Terminal Connector Terminal
RH B59
EXL
E14 59 6 Existed
LH B80
Is the inspection result normal? M
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK TAIL LAMP GROUND OPEN CIRCUIT N
Check continuity between rear combination lamp harness connector and ground.

Rear combination lamp O

Continuity
Connector Terminal
Ground
RH B59
3 Existed P
LH B80
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.

EXL-91
 LICENSE PLATE LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
LICENSE PLATE LAMP CIRCUIT
Component Function Check INFOID:0000000005912436

1.CHECK PARKING LAMP OPERATION

Check that the parking lamp is turned ON.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Refer to EXL-89, "Component Function Check".
2.CHECK LICENSE PLATE LAMP OPERATION
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the lighting switch, check that the license plate lamp is turned ON.

TAIL : License plate lamp ON

Off : License plate lamp OFF
Is the inspection result normal?
YES >> License plate lamp circuit is normal.
NO >> Refer to EXL-92, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000005912437

1.CHECK LICENSE PLATE LAMP BULB

Check the applicable lamp bulb.
Is the bulb normal?
YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and license plate lamp connector.
3. Check continuity between IPDM E/R harness connector and license plate lamp harness connector.

IPDM E/R License plate lamp

Continuity
Connector Terminal Connector Terminal
E14 59 B46 1 Existed
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between license plate lamp harness connector and ground.

License plate lamp

Continuity
Connector Terminal Ground
B46 2 Existed
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.

EXL-92
 OPTICAL SENSOR
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
OPTICAL SENSOR
A
Component Function Check INFOID:0000000006765745

1.CHECK OPTICAL SENSOR SIGNAL BY CONSULT B

CONSULT DATA MONITOR
1. Turn ignition switch ON.
2. Select “OPTISEN (DTCT)” of BCM (HEADLAMP) data monitor item. C
3. Turn lighting switch AUTO.
4. With the optical sensor illuminating, check the monitor status.
D
Monitor item Condition Voltage (Approx.)
When illuminating 3.1 V or more *
OPTISEN (DTCT) Optical sensor E
When shutting off light 0.6 V or less
*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.
Is the inspection result normal?
F
YES >> Optical sensor is normal.
NO >> Refer to EXL-93, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006765746 G

1.CHECK OPTICAL SENSOR POWER SUPPLY INPUT

1. Turn ignition switch ON. H
2. Turn lighting switch AUTO.
3. Check voltage between optical sensor harness connector and ground.
I
(+)
Voltage
Optical sensor (−)
(Approx.) J
Connector Terminal
M17 1 Ground 5V
Is the inspection result normal? K
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK OPTICAL SENSOR GROUND INPUT EXL
Check voltage between optical sensor harness connector and ground.
M
(+)
Voltage
Optical sensor (−)
(Approx.)
Connector Terminal N
M17 3 Ground 0V
Is the inspection result normal?
O
YES >> GO TO 3.
NO >> GO TO 6.
3.CHECK OPTICAL SENSOR SIGNAL OUTPUT P
With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.

EXL-93
 OPTICAL SENSOR
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]

(+)
Voltage
Optical sensor (−) Condition
(Approx.)
Connector Terminal
When illuminating 3.1 V or more *
M17 2 Ground Optical sensor
When shutting off light 0.6 V or less
*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Replace the optical sensor.
4.CHECK OPTICAL SENSOR OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.

Optical sensor BCM

Continuity
Connector Terminal Connector Terminal

M65*1
M17 1 17 Existed
M68*2

*1: Without Intelligent Key

*2: With Intelligent Key
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
5.CHECK OPTICAL SENSOR SHORT CIRCUIT
Check continuity between optical sensor harness connector and ground.

Optical sensor
Continuity
Connector Terminal Ground
M17 1 Not existed
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key) or BCS-338,
"Removal and Installation" (without Intelligent Key).
NO >> Repair or replace harness.
6.CHECK OPTICAL SENSOR GROUND OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.

Optical sensor BCM

Continuity
Connector Terminal Connector Terminal

M65*1
M17 3 18 Existed
M68*2

*1: Without Intelligent Key

*2: With Intelligent Key
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key) or BCS-338,
"Removal and Installation" (without Intelligent Key).

EXL-94
 OPTICAL SENSOR
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
NO >> Repair or replace harness.
7.CHECK OPTICAL SENSOR SIGNAL OPEN CIRCUIT A

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.
B
3. Check continuity between optical sensor harness connector and BCM harness connector.

Optical sensor BCM

Continuity C
Connector Terminal Connector Terminal

M65*1
M17 2 14 Existed
M68*2 D
*1: Without Intelligent Key
*2: With Intelligent Key
E
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace harness.
F
8.CHECK OPTICAL SENSOR SHORT CIRCUIT
Check continuity between optical sensor harness connector and ground.
G
Optical sensor
Continuity
Connector Terminal Ground
H
M17 2 Not existed
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key) or BCS-338, I
"Removal and Installation" (without Intelligent Key).
NO >> Repair or replace harness.
J

EXL

EXL-95
 FRONT FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
FRONT FOG LAMP CIRCUIT
Component Function Check INFOID:0000000005912416

1.CHECK FRONT FOG LAMP OPERATION

CONSULT ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the front fog lamp is turned ON.

Fog : Front fog lamp ON

Off : Front fog lamp OFF
Is the inspection result normal?
YES >> Front fog lamp circuit is normal.
NO >> Refer to EXL-96, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000005912417

1.CHECK FRONT FOG LAMP INPUT SIGNAL

CONSULT ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect front fog lamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5. With operating the test items, check voltage between front fog lamp harness connector and ground.

(+)
Voltage
Front fog lamp (−) Test item
(Approx.)
Connector Terminal
Fog Battery voltage
RH E48
Off 0V
1 Ground EXTERNAL LAMPS
Fog Battery voltage
LH E30
Off 0V
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK FRONT FOG LAMP GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between front fog lamp harness connector and ground.

Front fog lamp

Continuity
Connector Terminal
Ground
RH E48
2 Existed
LH E30
Is the inspection result normal?
YES >> Replace bulb.
NO >> Repair or replace harness.
3.CHECK FRONT FOG LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove front fog lamp relay.
3. Check continuity between front fog lamp relay harness connector and front fog lamp harness connector.

EXL-96
 FRONT FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]

Front fog lamp Front fog lamp relay A

Continuity
Connector Terminal Connector Terminal
RH E48
1 E3 3 Existed B
LH E30
Is the inspection result normal?
YES >> Refer to GI-51, "Intermittent Incident". C
NO >> Repair or replace harness.

EXL

EXL-97
 FRONT FOG LAMP RELAY
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
FRONT FOG LAMP RELAY
Diagnosis Procedure INFOID:0000000006052964

1.CHECK FRONT FOG LAMP FUSE

1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.

Unit Fuse No. Capacity

Front fog lamp #39 15 A
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK FRONT FOG LAMP RELAY POWER SUPPLY CIRCUIT
1. Remove front fog lamp relay.
2. Check voltage front fog lamp relay harness connector and ground.

(+)
Voltage
Front fog lamp relay (–)
(Approx.)
Connector Terminal
2
E3 Ground Battery voltage
5
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK FRONT FOG LAMP RELAY CIRCUIT 1
CONSULT ACTIVE TEST
1. Install front fog lamp relay.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4. With operating the test items, check voltage between IPDM E/R harness connector and ground.

(+)
Voltage
IPDM E/R (–) Test item
(Approx.)
Connector Terminal

EXTERNAL Fog 0V
E10 21 Ground
LAMPS Off Battery voltage
Is the inspection result normal?
YES >> GO TO 5.
Fixed battery voltage>>Replace IPDM E/R.
Fixed 0 V>>GO TO 4.
4.CHECK FRONT FOG LAMP RELAY CIRCUIT 2
1. Remove front fog lamp relay.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front fog lamp relay harness connector.

IPDM E/R Front fog lamp relay

Continuity
Connector Terminal Connector Terminal
E10 21 E3 1 Existed
4. Check continuity between IPDM E/R harness connector and ground.

EXL-98
 FRONT FOG LAMP RELAY
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]

IPDM E/R A
Continuity
Connector Terminal Ground
E10 21 Not existed
B
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
C
5.CHECK FRONT FOG LAMP RELAY 1
1. Remove front fog lamp relay.
2. Check front fog lamp relay. D
Refer to EXL-99, "Component Inspection"
Is the inspection result normal?
YES >> Front fog lamp relay circuit is normal. E
NO >> Replace front fog lamp relay.
6.CHECK FRONT FOG LAMP RELAY 2
F
1. Remove front fog lamp relay.
2. Check front fog lamp relay.
Refer to EXL-99, "Component Inspection"
Is the inspection result normal? G
YES >> Replace IPDM E/R.
NO >> Replace front fog lamp relay.
H
Component Inspection INFOID:0000000006052965

1.CHECK FRONT FOG LAMP RELAY I

1. Turn ignition switch OFF.
2. Remove front fog lamp relay.
3. Check continuity between front fog lamp relay terminals. J

Terminal
Condition Continuity
Front fog lamp relay K
12 V direct current supply between termi-
Existed
3 5 nals 1 and 2
No current supply Not existed EXL
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace front fog lamp relay. M
SEF497Y

EXL-99
 REAR FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
REAR FOG LAMP CIRCUIT
Component Function Check INFOID:0000000006173725

1.CHECK REAR FOG LAMP OPERATION

CONSULT ACTIVE TEST
1. Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item.
2. With operating the test items, check that the rear fog lamp is turned ON.

On : Rear fog lamp ON

Off : Rear fog lamp OFF
Is the inspection result normal?
YES >> Rear fog lamp circuit is normal.
NO >> Refer to EXL-100, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006173726

1.CHECK REAR FOG LAMP BULB

Check applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK REAR FOG LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect rear combination lamp LH connector.
3. Turn ignition switch ON.
4. Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item.
5. With operating the test items, check voltage between rear combination lamp LH harness connector and
ground.

(+)
Voltage
Rear combination lamp LH (−) Test item
(Approx.)
Connector Terminal
On 12 V
B80 2 Ground RR FOG LAMP
Off 0V
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 3.
3.CHECK REAR FOG LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and rear combination lamp LH harness connector.

BCM Rear combination lamp LH

Continuity
Connector Terminal Connector Terminal

M66*1
52 B80 2 Existed
M69*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?

EXL-100
 REAR FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
YES >> GO TO 4.
NO >> Repair or replace harness. A
4.CHECK REAR FOG LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
B
BCM
Continuity
Connector Terminal
Ground C
M66*1
52 Not existed
M69*2
*1: Without Intelligent Key D
*2: With Intelligent Key
Is the inspection result normal?
YES >> Check bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer to E
BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338, "Removal and Installation"
(without Intelligent Key).
NO >> Repair or replace harness. F
5.CHECK REAR FOG LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp LH harness connector and ground.
G
Rear combination lamp LH
Continuity
Connector Terminal Ground
H
B80 3 Existed
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary. I
NO >> Repair or replace harness.

EXL

EXL-101
 TURN SIGNAL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
TURN SIGNAL LAMP CIRCUIT
Component Function Check INFOID:0000000005912425

1.CHECK TURN SIGNAL LAMP

CONSULT ACTIVE TEST
1. Select “FLASHER” of BCM (FLASHER) active test item.
2. With operating the test items, check that the turn signal lamps is turned ON.

LH : Turn signal lamps (LH) ON

RH : Turn signal lamps (RH) ON
Off : Turn signal lamps OFF
Is the inspection result normal?
YES >> Turn signal lamp circuit is normal.
NO >> Refer to EXL-102, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000005912426

1.CHECK TURN SIGNAL LAMP BULB

Check the applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1. Turn ignition switch OFF.
2. Disconnect front turn signal lamp connector, side turn signal lamp connector and rear combination lamp
connector.
3. Turn ignition switch ON.
4. With operating the turn signal switch, check voltage between BCM harness connector and ground.

(+)
Voltage
BCM (–) Condition
(Approx.)
Connector Terminal

LH
60

PKID0926E

M67*1 Turn signal OFF 0V

Ground
M70*2 switch

RH
61

PKID0926E

OFF 0V

*1: Without Intelligent Key

*2: With Intelligent Key

EXL-102
 TURN SIGNAL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
Is the inspection result normal?
YES >> GO TO 3. A
NO >> GO TO 4.
3.CHECK TURN SIGNAL LAMP OPEN CIRCUIT
B
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp harness connector. C
Front turn signal lamp
BCM Front turn signal lamp
Continuity D
Connector Terminal Connector Terminal
RH M67*1 61 E46
1 Existed
LH M70*2 60 E27 E
Side turn signal lamp
BCM Side turn signal lamp
Continuity
Connector Terminal Connector Terminal F
RH M67*1 61 E40
*2
1 Existed
LH M70 60 E23
G
Rear turn signal lamp
BCM Rear combination lamp
Continuity
Connector Terminal Connector Terminal H
RH M67*1 61 B59
*2
4 Existed
LH M70 60 B80
I
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal? J
YES >> GO TO 5.
NO >> Repair or replace harness.
4.CHECK TURN SIGNAL LAMP SHORT CIRCUIT K

Check continuity between BCM harness connector and ground.

EXL
BCM
Continuity
Connector Terminal
Ground
RH M67*1 61 M
Not existed
LH M70*2 60

*1: Without Intelligent Key

N
*2: With Intelligent Key
Is the inspection result normal?
YES >> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer O
to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338, "Removal and Installa-
tion" (without Intelligent Key).
NO >> Repair or replace harness.
P
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp and ground.

EXL-103
 TURN SIGNAL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
Front turn signal lamp
Front turn signal lamp
Continuity
Connector Terminal
Ground
RH E46
2 Existed
LH E27

Side turn signal lamp

Side turn signal lamp
Continuity
Connector Terminal
Ground
RH E40
2 Existed
LH E23

Rear turn signal lamp

Rear combination lamp
Continuity
Connector Terminal
Ground
RH B59
3 Existed
LH B80
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.

EXL-104
 HAZARD SWITCH
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
HAZARD SWITCH
A
Component Function Check INFOID:0000000005912430

1.CHECK HAZARD SWITCH SIGNAL BY CONSULT B

CONSULT DATA MONITOR
1. Turn the ignition switch ON.
2. Select “HAZARD SW” of BCM (FLASHER) data monitor item. C
3. With operating the hazard switch, check the monitor status.

Monitor item Condition Monitor status D

ON On
HAZARD SW Hazard switch
OFF Off
E
Is the inspection result normal?
YES >> Hazard switch circuit is normal.
NO >> Refer to EXL-105, "Diagnosis Procedure".
F
Diagnosis Procedure INFOID:0000000005912431

1.CHECK HAZARD SWITCH SIGNAL INPUT G

1. Turn ignition switch OFF.
2. Disconnect hazard switch connector.
3. Check voltage between hazard switch connector and ground. H

(+)
Hazard switch (−) Voltage (Approx.) I
Connector Terminal
M45 2 Ground 12 V
J
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
K
2.CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between hazard switch harness connector and BCM harness connector. EXL

Hazard switch BCM

Continuity
Connector Terminal Connector Terminal M
M65*1
M45 2 29 Existed
M68*2
*1: Without Intelligent Key N
*2: With Intelligent Key
Is the inspection result normal?
O
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT P
Check continuity between hazard switch harness connector and ground.

Hazard switch
Continuity
Connector Terminal Ground
M45 2 Not existed
Is the inspection result normal?

EXL-105
 HAZARD SWITCH
< DTC/CIRCUIT DIAGNOSIS > [TYPE 1]
YES >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key) or BCS-338,
"Removal and Installation" (without Intelligent Key).
NO >> Repair or replace harness.
4.CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
Check continuity between hazard switch harness connector and ground.

Hazard switch
Continuity
Connector Terminal Ground
M45 1 Existed
Is the inspection result normal?
YES >> Replace hazard switch.
NO >> Repair or replace harness.

EXL-106
 EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [TYPE 1]

SYMPTOM DIAGNOSIS A
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table INFOID:0000000005912466
B
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected. C

Symptom Possible cause Inspection item

• Fuse D
• Halogen bulb
• Harness between IPDM E/R and Headlamp (HI) circuit
One side headlamp Refer to EXL-83, "Component
E
Headlamp (HI) is not • Harness between headlamp and Function Check".
turned ON. ground
• IPDM E/R
Symptom diagnosis F
Both sides “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to EXL-109, "Diagnosis Procedure".
• Combination meter G
High beam indicator lamp is not turned ON. Data monitor “HI-BEAM IND”
Combination meter
[Headlamp (HI) is turned ON.] • BCM (HEADLAMP)
Active test “HEADLAMP”
H
• Fuse
• Halogen bulb
• Harness between IPDM E/R and Headlamp (LO) circuit
Headlamp (LO) is not One side headlamp Refer to EXL-85, "Component I
turned ON. • Harness between headlamp and Function Check".
ground
• IPDM E/R
Both sides
J
Symptom diagnosis
When ignition switch “BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
is turned ON. Refer to EXL-110, "Diagnosis Procedure".
Headlamp is not turned
OFF. K
When ignition switch
IPDM E/R —
is turned OFF.
• Harness between headlamp and Headlamp ground circuit
Headlamp HI and LO are not turned ON. ground Refer to EXL-87, "Diagnosis Proce- EXL
• Halogen bulb dure".
• Combination switch
Combination switch
• Harness between combination
Refer to BCS-196, "Symptom Ta-
M
switch and BCM
ble".
Headlamp is not turned ON/OFF with the lighting • BCM
switch AUTO. • Optical sensor
Optical sensor N
• Harness between optical sensor
Refer to EXL-93, "Component
and BCM
Function Check".
• BCM
• Parking lamp bulb O
Parking lamp circuit
• Harness between IPDM E/R and
Parking lamp is not turned ON. Refer to EXL-89, "Component
parking lamp
Function Check".
• IPDM E/R
P
• Tail lamp bulb
• Harness between IPDM E/R and Tail lamp circuit
Tail lamp is not turned ON. rear combination lamp Refer to EXL-91, "Component
• Rear combination lamp assembly Function Check".
• IPDM E/R

EXL-107
 EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [TYPE 1]
Symptom Possible cause Inspection item
• License plate lamp bulb License plate lamp circuit
License plate lamp is not turned ON. • Harness between IPDM E/R and Refer to EXL-92, "Component
license plate lamp Function Check".
• Parking lamp, tail lamp and license plate lamp
are not turned ON. Symptom diagnosis
• Parking lamp, tail lamp and license plate lamp “PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
are not turned OFF. Refer to EXL-111, "Diagnosis Procedure".
(Each illumination is turned ON/OFF.)
Indicator lamp is nor-
mal. • Harness between BCM and each Turn signal lamp circuit
(Applicable side per- turn signal lamp Refer to EXL-102, "Component
forms the high flasher • Turn signal lamp bulb Function Check".
Turn signal lamp does activation.)
not blink.
• Combination switch
Combination switch
Indicator lamp is in- • Harness between combination
Refer to BCS-196, "Symptom Ta-
cluded. switch and BCM
ble".
• BCM
One side Combination meter —
• Combination meter
• Turn signal indicator lamp signal
Both sides Data monitor “TURN IND”
- BCM
Turn signal indicator (Always) • BCM (FLASHER)
• Combination meter
lamp does not blink. Active test “FLASHER”
(Turn signal indicator
Both sides
lamp is normal.) Combination meter
(Only when activating • Combination meter power supply
Power supply and ground circuit
hazard warning lamp and ground circuit
Refer to MWI-123, "COMBINATION
with the ignition switch • Combination meter
METER : Diagnosis Procedure".
OFF.)
• Hazard switch
• Hazard warning lamp does not activate. Hazard switch
• Harness between hazard switch
• Hazard warning lamp continues activating. Refer to EXL-105, "Component
and BCM
(Turn signal is normal.) Function Check".
• BCM
• Front fog lamp bulb
• Harness between front fog lamp Front fog lamp circuit
Front fog lamp is not One side relay and front fog lamp Refer to EXL-96, "Component
turned ON. • Front fog lamp Function Check".
• Front fog lamp relay
Both side Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Front fog lamp is not turned OFF. Refer to EXL-112, "Diagnosis Procedure".
• Combination meter
Front fog lamp indicator is not turned ON. Data monitor “FR FOG IND”
Combination meter
(Front fog lamp is turned ON.) • BCM (HEAD LAMP)
Active test “FR FOG LAMP”
• Harness between BCM and rear
Rear fog lamp circuit
Rear fog lamp indica- fog lamp
Refer to EXL-100, "Component
tor lamp is normal. • Rear fog lamp bulb
Function Check".
Rear fog lamp is not • BCM
turned ON. • Combination switch
Combination switch
Rear fog lamp indica- • Harness between combination
Refer to BCS-196, "Symptom Ta-
tor lamp is included. switch and BCM
ble".
• BCM
• Combination meter
• Rear fog lamp status signal
Rear fog lamp indicator lamp is not turn ON. Data monitor “RR FOG IND”
- BCM
(Rear fog lamp turns ON) • BCM (HEAD LAMP)
• Combination meter
Active test “RR FOG LAMP”

EXL-108
 BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [TYPE 1]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
A
Description INFOID:0000000005912469

Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS. B
Diagnosis Procedure INFOID:0000000005912470

1.COMBINATION SWITCH INSPECTION C

Check the combination switch. Refer to BCS-196, "Symptom Table".
Is the inspection result normal?
D
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT E
CONSULT DATA MONITOR
1. Select “HL HI REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status. F

Monitor item Condition Monitor status

Lighting switch HI or PASS ON G

HL HI REQ
(2ND) LO OFF
Is the inspection result normal? H
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
I
3.HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to EXL-83, "Component Function Check".
Is the inspection result normal? J
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
K

EXL

EXL-109
 BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [TYPE 1]
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description INFOID:0000000005912471

Both side headlamps (LO) are not turned ON in any condition.

Diagnosis Procedure INFOID:0000000005912472

1.CHECK COMBINATION SWITCH

Check the combination switch. Refer to BCS-196, "Symptom Table".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “HL LO REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.

Monitor item Condition Monitor status

2ND ON
HL LO REQ Lighting switch
OFF OFF
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
3.HEADLAMP (LO) CIRCUIT INSPECTION
Check the headlamp (LO) circuit. Refer to EXL-85, "Component Function Check".
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.

EXL-110
 PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [TYPE 1]
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
A
Description INFOID:0000000005912473

The parking, license plate, tail lamps and each illumination are not turned ON in any condition. B
Diagnosis Procedure INFOID:0000000005912474

1.COMBINATION SWITCH INSPECTION C

Check the combination switch. Refer to BCS-196, "Symptom Table".
Is the inspection result normal?
D
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT E
CONSULT DATA MONITOR
1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status. F

Monitor item Condition Monitor status

1ST ON G
TAIL & CLR REQ Lighting switch
OFF OFF
Is the inspection result normal? H
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
I
3.PARKING LAMP CIRCUIT INSPECTION
Check the parking lamp circuit. Refer to EXL-89, "Component Function Check".
Is the inspection result normal? J
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
K

EXL

EXL-111
 BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [TYPE 1]
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description INFOID:0000000005912475

The front fog lamps are not turned ON in any condition.

Diagnosis Procedure INFOID:0000000005912476

1.CHECK FUSE
Check that the following fuse is fusing.

Unit Fuse No. Capacity

Front fog lamp #39 15 A
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the applicable circuit. And then replace the fuse.
2.COMBINATION SWITCH INSPECTION
Check combination switch. Refer to BCS-196, "Symptom Table".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning part.
3.CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “FR FOG REQ” of IPDM E/R data monitor item.
2. With operating the front fog lamp switch, check the monitor status.

Monitor item Condition Monitor status

Front fog lamp switch ON ON

FR FOG REQ
(With lighting switch 1ST) OFF OFF
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
4.FRONT FOG LAMP RELAY CIRCUIT INSPECTION
Check front fog lamp relay circuit. Refer to EXL-98, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning part.
5.FRONT FOG LAMP CIRCUIT INSPECTION
Check front fog lamp circuit. Refer to EXL-96, "Component Function Check".
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.

EXL-112
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 1]

PERIODIC MAINTENANCE A
HEADLAMP AIMING ADJUSTMENT
LHD
B
LHD : Description INFOID:0000000006425598

PREPARATION BEFORE ADJUSTING C

NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been D
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification. E
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE: F
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION: G
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW H

EXL

JMLIA1020ZZ P

A. Headlamp RH (UP/DOWN) B. Headlamp RH (INSIDE/OUTSIDE) C. Headlamp LH (INSIDE/OUTSIDE)

adjustment screw adjustment screw adjustment screw
D. Headlamp LH (UP/DOWN)
adjustment screw
: Vehicle center

EXL-113
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 1]

Adjustment screw Screw driver rotation Facing direction

Clockwise UP
A Headlamp RH (UP/DOWN)
Counterclockwise DOWN
Clockwise INSIDE
B Headlamp RH (INSIDE/OUTSIDE)
Counterclockwise OUTSIDE
Clockwise INSIDE
C Headlamp LH (INSIDE/OUTSIDE)
Counterclockwise OUTSIDE
Clockwise UP
D Headlamp LH (UP/DOWN)
Counterclockwise DOWN

LHD : Aiming Adjustment Procedure INFOID:0000000006425599

1. Place the screen.

NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
• Set the screen so that it is perpendicular to a level load surface.
2. Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3. Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:
Do not cover lens surface with tape, etc. because it is made from plastic.
4. Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
Low beam distribution on the screen

JSLIA0030ZZ

A. Aiming adjustment area

B. Elbow point
C. Headlamp center
H. Horizontal center line of headlamp
V. Vertical center line of headlamp

EXL-114
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 1]

JSLIA0031ZZ F

C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
G
(lateral) (Vertical)

Distance from headlamp center to screen (L) : 10 m (32.8 ft) H

Unit: mm (in)
Aiming adjustment area
Vertical direction (Y) Lateral direction (X) I
(Lower side from headlamp center height) (Right side from headlamp center line)
Highest light axis 100 3.94)
Target light axis 100 (3.94) 0 -100 (3.94) J
Lowest light axis 150 (5.91)

RHD K

RHD : Description INFOID:0000000006425600

EXL
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been M
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification. N
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.) O
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
P
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW

EXL-115
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 1]

JMLIA1020ZZ

A. Headlamp RH (UP/DOWN) B. Headlamp RH (INSIDE/OUTSIDE) C. Headlamp LH (INSIDE/OUTSIDE)

adjustment screw adjustment screw adjustment screw
D. Headlamp LH (UP/DOWN)
adjustment screw
: Vehicle center

Adjustment screw Screw driver rotation Facing direction

Clockwise UP
A Headlamp RH (UP/DOWN)
Counterclockwise DOWN
Clockwise INSIDE
B Headlamp RH (INSIDE/OUTSIDE)
Counterclockwise OUTSIDE
Clockwise INSIDE
C Headlamp LH (INSIDE/OUTSIDE)
Counterclockwise OUTSIDE
Clockwise UP
D Headlamp LH (UP/DOWN)
Counterclockwise DOWN

RHD : Aiming Adjustment Procedure INFOID:0000000006425601

1. Place the screen.

NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
• Set the screen so that it is perpendicular to a level load surface.
2. Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3. Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:

EXL-116
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 1]
Do not cover lens surface with tape, etc. because it is made from plastic.
4. Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so A
that it is within the aiming adjustment area.
Low beam distribution on the screen
B

JSLIA0028ZZ
E
A. Aiming adjustment area
B. Elbow point
C. Headlamp center F
H. Horizontal center line of headlamp
V. Vertical center line of headlamp
G

JSLIA0029ZZ
EXL
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
(lateral) (Vertical) M

Distance from headlamp center to screen (L) : 10 m (32.8 ft)

N
Unit: mm (in)
Aiming adjustment area
Vertical direction (Y) Lateral direction (X)
(Lower side from headlamp center height) (Left side from headlamp center line)
O

Highest light axis 100 (3.94)

Target light axis 100 (3.94) 0 -100 (3.94)
P
Lowest light axis 150 (5.91)

EXL-117
 FRONT FOG LAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 1]
FRONT FOG LAMP AIMING ADJUSTMENT
Description INFOID:0000000006056702

PREPARATION BEFORE ADJUSTING

NOTE:
• For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.

A: UP
B: DOWN
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.

JMLIA1040ZZ

Aiming Adjustment Procedure INFOID:0000000006056703

1. Place the screen.

NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2. Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3. Start the engine. Illuminate the front fog lamp.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4. Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen

JPLIA0008ZZ

EXL-118
 FRONT FOG LAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 1]

A : Cutoff line A
B : High illuminance area
H : Horizontal center line of front fog lamp
V : Vertical center line of front fog lamp B
X : Cutoff line height

EXL

EXL-119
 FRONT COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]

REMOVAL AND INSTALLATION

FRONT COMBINATION LAMP
Exploded View INFOID:0000000005912481

REMOVAL

JMLIA1031ZZ

1. Front combination lamp

DISASSEMBLY

EXL-120
 FRONT COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]

H
JMLIA1032ZZ

1. Halogen bulb 2. Back cover 3. Parking lamp bulb socket

4. Parking lamp bulb 5. Retaining spring 6. Front turn signal lamp bulb socket I
7. Front turn signal lamp bulb 8. Headlamp housing assembly

Removal and Installation INFOID:0000000005912482 J

REMOVAL
CAUTION: K
Disconnect the battery negative terminal or the fuse.
1. Remove front bumper fascia. Refer to EXT-14, "Removal and Installation".
2. Remove the headlamp mounting bolts. EXL
3. Pull out the headlamp assembly forward the vehicle.
4. Disconnect the connectors, and then remove headlamp assembly.
M
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-113, "LHD : Description". N

Replacement INFOID:0000000005912483

CAUTION: O
• Disconnect the battery negative terminal or the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it. P
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1. Disconnect the headlamp bulb connector.
2. Remove the back cover.

EXL-121
 FRONT COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
3. Remove the retaining spring lock. And remove the bulb from the headlamp housing assembly.
PARKING LAMP BULB
1. Rotate the bulb socket counterclockwise and unlock it.
2. Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1. Rotate the bulb socket counterclockwise and unlock it.
2. Remove the bulb from the bulb socket.
Disassembly and Assembly INFOID:0000000005912484

DISASSEMBLY
1. Remove the back cover.
2. Remove the retaining spring lock, and then remove the bulb from the headlamp housing assembly.
3. Rotate the parking lamp bulb socket counterclockwise and unlock it.
4. Remove the bulb from the parking lamp bulb socket.
5. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
6. Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.

EXL-122
 FRONT FOG LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
FRONT FOG LAMP
A
Exploded View INFOID:0000000005912485

JMLIA1033ZZ

1. Front fog lamp bulb 2. Front fog lamp 3. Front fog lamp bracket G
4. Front bumper

Removal and Installation INFOID:0000000005912486 H

CAUTION:
Disconnect the battery negative terminal or the fuse.
I
REMOVAL
1. Remove the fender protector. Refer to EXT-21, "FENDER PROTECTOR : Removal and Installation".
2. Remove the front fog lamp connector. J
3. Remove the fixing screws, and then remove front fog lamp.
INSTALLATION K
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-118, "Description".
EXL
Replacement INFOID:0000000005912487

CAUTION: M
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect N
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
O
1. Remove the fender protector. Keep the service area.Refer to EXT-21, "FENDER PROTECTOR : Removal
and Installation".

EXL-123
 FRONT FOG LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
2. Remove the front fog lamp bulb connector (1).
3. Rotate the bulb (2) counterclockwise and unlock it.

SKIB8304J

EXL-124
 OPTICAL SENSOR
< REMOVAL AND INSTALLATION > [TYPE 1]
OPTICAL SENSOR
A
Removal and Installation INFOID:0000000006426114

REMOVAL B
1. Insert an appropriate tool between the optical sensor and the instrument upper panel. Pull out the optical
sensor upward.
2. Disconnect the connector. Remove the optical sensor. C

INSTALLATION
Install in the reverse order of removal.
D

EXL

EXL-125
 LIGHTING & TURN SIGNAL SWITCH
< REMOVAL AND INSTALLATION > [TYPE 1]
LIGHTING & TURN SIGNAL SWITCH
Exploded View INFOID:0000000005912490

The lighting & turn switch is integrated in the combination switch. Refer to BCS-199, "Removal and Installa-
tion".

EXL-126
 SIDE TURN SIGNAL LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
SIDE TURN SIGNAL LAMP
A
Exploded View INFOID:0000000005912491

JPLIA1809ZZ

1. Side turn signal lamp bulb socket 2. Side turn signal lamp bulb 3. Side turn signal lamp housing G

Removal and Installation INFOID:0000000005912492

H
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL I
1. Remove the side turn signal lamp in numerical order shown in the figure.

: Vehicle front J
2. Rotate the bulb socket counterclockwise and unlock it.
NOTE:
Support side turn signal lamp harness with tape so that it won't K
fall into the front fender.

EXL

JMLIA1302ZZ
M
INSTALLATION
1. Rotate the bulb socket clockwise and lock it.
2. Fix the pawl-side behind the side turn signal lamp housing first, then push the resin clip-side. N
Replacement INFOID:0000000005912493

CAUTION: O
• Disconnect battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off. P
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
SIDE TURN SIGNAL LAMP BULB
1. Remove the side turn signal lamp.
2. Rotate the bulb socket counterclockwise and unlock it.
NOTE:

EXL-127
 SIDE TURN SIGNAL LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
Support the vehicle-side harness of the side turn signal lamp with tape so that it does not drop inside the
front fender.
3. Remove the bulb from the bulb socket.

EXL-128
 HAZARD SWITCH
< REMOVAL AND INSTALLATION > [TYPE 1]
HAZARD SWITCH
A
Exploded View INFOID:0000000005912494

JMLIA1042ZZ

1. Cluster lid C 2. Hazard switch G

Pawl

Removal and Installation INFOID:0000000005912495

H

REMOVAL
I
1. Remove the cluster lid C. Refer to IP-14, "Exploded View".
2. While pressing pawls, push the hazard switch to remove it.
INSTALLATION J
Install in the reverse order of removal.

EXL

EXL-129
 REAR COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
REAR COMBINATION LAMP
Exploded View INFOID:0000000005912496

REMOVAL

JMLIA1034ZZ

1. Grommet 2. Rear combination lamp

DISASSEMBLY

JMLIA1035ZZ

1. Stop/tail lamp bulb 2. Rear turn signal lamp bulb 3. Back-up lamp bulb/
Rear fog lamp bulb (LHD left side)
4. Bulb holder 5. Seal packing
Refer to GI-4, "Components" for symbols in the figure.

Removal and Installation INFOID:0000000005912497

CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Wrap the tip of remover tool with a cloth to protect the body from damage.
REMOVAL
1. Remove rear combination lamp mounting bolts.
2. Pull rear combination lamp toward rear of the vehicle.
3. Disconnect rear combination lamp connector, and then remove rear combination lamp.

EXL-130
 REAR COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
INSTALLATION
Install in the reverse order of removal. A

Replacement INFOID:0000000005912498

CAUTION: B
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off. C
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP BULB D
1. Remove rear combination lamp assembly.
2. Disengage fixing pawls, and then remove bulb holder.
E

JMLIA1041ZZ
H
3. Rotate stop/tail lamp bulb counterclockwise, and then remove stop/tail lamp bulb.
REAR TURN SIGNAL LAMP BULB I
1. Remove rear combination lamp assembly.
2. Disengage fixing pawls, and then remove bulb holder.
J

EXL

JMLIA1041ZZ

M
3. Rotate rear turn signal lamp bulb counterclockwise, and then remove rear turn signal lamp bulb.
BACK-UP LAMP BULB
N
1. Remove rear combination lamp assembly.
2. Disengage fixing pawls, and then remove bulb holder.
O

JMLIA1041ZZ

EXL-131
 REAR COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
3. Rotate back-up lamp bulb counterclockwise, and then remove back-up lamp bulb.
REAR FOG LAMP BULB
1. Remove rear combination lamp assembly.
2. Disengage fixing pawls, and then remove bulb holder.

JMLIA1041ZZ

3. Rotate rear fog lamp bulb counterclockwise, and then remove rear fog lamp bulb.

EXL-132
 HIGH-MOUNTED STOP LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
HIGH-MOUNTED STOP LAMP
A
WITHOUT REAR SPOILER
WITHOUT REAR SPOILER : Exploded View INFOID:0000000005912502
B

JMLIA1036ZZ

H
1. Back door 2. Grommet 3. High-mounted stop lamp socket
4. High-mounted stop lamp bulb 5. Seal packing 6. High-mounted stop lamp
Refer to GI-4, "Components" for symbols in the figure.
I
WITHOUT REAR SPOILER : Removal and Installation INFOID:0000000005912503

CAUTION: J
Disconnect battery negative terminal or remove the fuse.
REMOVAL
K
1. Disengage high-mounted stop lamp fixing pawls with remover
tool (A).

: Metal clip EXL

CAUTION:
• Apply protect tape (B) on back door to protect the painted
surface from damage. M

N
JMLIA1021ZZ

• Never insert remover tool in the back door glass side to

O
prevent damage of back door glass.

JMLIA1022ZZ

EXL-133
 HIGH-MOUNTED STOP LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
2. Pull the high-mounted stop lamp toward rear of the vehicle.
3. Disconnect the high-mounted stop lamp harness connector, and then remove high-mounted stop lamp.
INSTALLATION
Install in the reverse order of removal.
WITHOUT REAR SPOILER : Replacement INFOID:0000000005912504

CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HIGH-MOUNTED STOP LAMP BULB
1. Remove the high-mounted stop lamp.
2. Rotate the bulb socket counterclockwise, and unlock it.
3. Remove the bulb from the bulb socket.
WITH REAR SPOILER
WITH REAR SPOILER : Exploded View INFOID:0000000006095130

High-mounted stop lamp is integrated in the rear spoiler. Refer to EXT-29, "Exploded View".
WITH REAR SPOILER : Removal and Installation INFOID:0000000006095131

REMOVAL
1. Remove rear spoiler. Refer to EXT-30, "Removal and Installation".
2. Remove high-mounted stop lamp cover fixing screws, and then remove high-mounted stop lamp cover.
3. Remove high-mounted stop lamp from rear spoiler.
INSTALLATION
Install in the reverse order of removal.

EXL-134
 LICENSE PLATE LAMP
< REMOVAL AND INSTALLATION > [TYPE 1]
LICENSE PLATE LAMP
A
Exploded View INFOID:0000000005912505

G
JMLIA1037ZZ

1. License plate lamp connector 2. License plate lamp bulb 3. License plate lamp housing
H
Removal and Installation INFOID:0000000005912506

CAUTION: I
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. While pressing the license plate lamp fixing pawl to direction right side, pull it to direction lower side and J
then remove it.
2. Rotate the bulb socket counterclockwise, and then remove bulb socket.
3. Remove the license plate lamp. K

INSTALLATION
Install in the reverse order of removal.
EXL
Replacement INFOID:0000000005912507

CAUTION: M
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect N
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
O
1. Remove the license plate lamp.
2. Remove the bulb from the socket.
P

EXL-135
 HEADLAMP AIMING SWITCH
< REMOVAL AND INSTALLATION > [TYPE 1]
HEADLAMP AIMING SWITCH
Exploded View INFOID:0000000006291189

For LHD models

JMLIA1147ZZ

1. Instrument lower panel assembly LH 2. Headlamp aiming switch 3. Switch panel

: Pawl

For RHD models

JMLIA1141ZZ

1. Instrument lower panel assembly RH 2. Headlamp aiming switch 3. Switch panel

: Pawl

Removal and Installation INFOID:0000000006291190

REMOVAL
1. Remove the switch panel with remover tool (A).
CAUTION:
Apply protective tape (B) on the part to protect from damage

2. Disengage the headlamp aiming switch harness connector and mirror control switch harness connector (if
so equipped).
3. Remove the headlamp aiming switch from switch panel.
INSTALLATION
Install in the reverse order of removal.

EXL-136
 SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS) [TYPE 1]

SERVICE DATA AND SPECIFICATIONS (SDS) A

SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications INFOID:0000000005912508
B

Item Type Wattage (W)

C
Headlamp (HI/LO) H4 60/55
Front combination lamp Front turn signal lamp PY21W (Amber) 21
Parking lamp W5W 5 D
Front fog lamp H11 55
Side turn signal lamp WY5W (Amber) 5
E
Stop lamp/Tail lamp P21W 21/5
Rear turn signal lamp PY21W (Amber) 21
Rear combination lamp
Back-up lamp P21W 21 F
Rear fog lamp P21W 21
License plate lamp W5W 5
High-mounted stop lamp W16W 18 G

EXL

EXL-137
 APPLICATION NOTICE
< HOW TO USE THIS MANUAL > [TYPE 2]

HOW TO USE THIS MANUAL

APPLICATION NOTICE
Information INFOID:0000000006760465

• Check the vehicle type to use the service information in this section.

Service information Destination

• General areas
Thai production models • Australia and New Zealand
• Hong Kong
Type 1
China production models China
India production models India
• Europe (LH and RH drive)
Type 2 India production models • Lebanon and Jordan
• General areas (LH and RH drive)
Refer to general information.
• In this manual, “Idling Stop System” is referred to as “Stop / Start System”.

EXL-138
 PRECAUTIONS
< PRECAUTION > [TYPE 2]

PRECAUTION A
PRECAUTIONS
FOR EUROPE
B
FOR EUROPE : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER" INFOID:0000000006756539

C
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and D
“SEAT BELT” of this Service Manual.

The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a E
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas- F
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.
G
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in H
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal I
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har- J
ness connectors.
• The vehicle may be equipped with a passenger air bag deactivation switch which can be operated by
the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled and K
will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled and
could inflate for certain types of collision. After SRS maintenance or repair, make sure the passenger
air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived for ser-
vice. EXL

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING: M
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly N
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service. O
FOR EUROPE : Precautions Necessary for Steering Wheel Rotation After Battery Dis-
connection INFOID:0000000006756540
P
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.

EXL-139
 PRECAUTIONS
< PRECAUTION > [TYPE 2]
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT.
EXCEPT FOR EUROPE
EXCEPT FOR EUROPE : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000006891604

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
EXCEPT FOR EUROPE : Precautions Necessary for Steering Wheel Rotation After
Battery Disconnection INFOID:0000000006891603

CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables.

EXL-140
 PRECAUTIONS
< PRECAUTION > [TYPE 2]
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables. A
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
B
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
C
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
D
Supply power using jumper cables if battery is discharged.
2. Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
E
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
F
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT. G

EXL

EXL-141
 COMPONENT PARTS
< SYSTEM DESCRIPTION > [TYPE 2]

SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location INFOID:0000000006765768

JMLIA1579ZZ

1. Light & rain sensor*1 2. Hazard switch 3. Combination switch

4. Headlamp aiming switch 5. Combination meter 6. IPDM E/R
Refer to PCS-8, "Component Parts
Location".
7. Front turn signal lamp 8. Headlamp 9. Parking lamp
10. Front fog lamp*2 11. ECM 12. BCM
Refer to EC4-15, Refer to BCS-9, "BODY CONTROL
"Component Parts Location". SYSTEM : Component Parts Loca-
tion".
13. Side turn signal lamp 14. Rear fog lamp 15. License plate lamp
16. Tail lamp 17. Rear turn signal lamp 18. Front door switch (driver side)
19. Remote keyless entry receiver*3 20. Aiming motor 21. Front fog lamp relay*2
Refer to DLK-28,
"Component Parts Location"
22. Tail lamp RH relay 23. Tail lamp LH relay
A. Front combination lamp (back) B. View with glove box cover assembly
is removed

*1: With auto light system

*2: With front fog lamp
*3: With remote key less entry system

EXL-142
 COMPONENT PARTS
< SYSTEM DESCRIPTION > [TYPE 2]
Component Description INFOID:0000000006756542

Part Description
• Detects each switch condition by the combination switch reading function B
• Judges that the headlamp is turned ON according to the vehicle condition
• Requests the headlamp relay (HI/LO) ON to IPDM E/R (via CAN communication)
• Requests the high beam indicator lamp front fog lamp indicator lamp*1 and rear fog
BCM lamp indicator lamp ON to the combination meter (via CAN communication)
C
• Receives exterior lamp ON/OFF requests from the light & rain sensor by light & rain
sensor serial link.*2
• Judges the ON/OFF status of the exterior lamp according to requests from light & D
rain sensor and the vehicle condition.*2
ECM Transmits engine status signal to BCM. (via CAN communication)
Controls the integrated relay, and supplies voltage to the load according to the request E
IPDM E/R
from BCM (via CAN communication).
• Blinks the turn signal indicator lamp and outputs the turn signal operating sound with
integrated buzzer according to the request from BCM (via CAN communication).
Combination meter F
• Turns the tail lamp indicator lamp, high beam indicator lamp, front fog lamp indicator
lamp and rear fog lamp indicator lamp ON according to the request from BCM (via
CAN communication).

Light & rain sensor*2 Refer to EXL-143, "Light & Rain Sensor". G
The headlamp levelizer adjusts the headlamp light axis upward and downward with
Head lamp aiming motor
the aiming motor integrated in the headlamp.
H
Combination switch Refer to BCS-16, "COMBINATION SWITCH READING SYSTEM : System Descrip-
(Lighting & turn signal switch) tion".
Headlamp aiming switch Adjusts height of headlamp aiming.
I
Door switch Refer to DLK-29, "Component Description".
Hazard switch Inputs the hazard switch signal to BCM.
*1: with front fog lamp J
*2
: with auto light system

Light & Rain Sensor INFOID:0000000006756543

K

• The light & rain sensor detects the outside ambient light level, for-
ward light level and sensor conditions.
• Based on ambient light level (day/night detection), forward light EXL
level (tunnel detection) and sensor conditions it judges ON/OFF
condition for exterior lamps.
• And it transmits exterior lamp ON/OFF request to the BCM by the M
light & rain sensor serial link.
• BCM controls each function depending on the signals. And it
detects the light & rain sensor serial link error and the light & rain
sensor malfunction. N

JSLIA0093ZZ

EXL-143
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
SYSTEM
HEADLAMP SYSTEM
HEADLAMP SYSTEM : System Diagram INFOID:0000000006765883

JPLIA0167GB

HEADLAMP SYSTEM : System Description INFOID:0000000006756545

OUTLINE
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R using CAN communication according to the head-
lamp (LO) ON condition.
Headlamp (LO) ON condition
- Lighting switch 2ND
- Lighting switch AUTO (auto light function ON judgment)
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
HEADLAMP (HI) OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter using CAN communi-
cation according to the headlamp (HI) ON condition. At this time, BCM stops to transmit low beam request
signal.
Headlamp (HI) ON condition
- Lighting switch HI with the lighting switch 2ND or AUTO (auto light function ON judgment)
- Lighting switch PASS
- Lighting switch AUTO, with the front fog lamp switch ON, the ignition switch ON and lighting switch HI.
• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
FOLLOW ME HOME FUNCTION
When the driver is moving to the house entrance from the own vehicle, headlamp is kept still ON by the follow
me home function of BCM.
• When BCM detects the input of lighting switch PASS while all of following conditions satisfied, it transmits
the low beam request signal for a period of time to IPDM E/R through CAN communication.
Follow me home ON condition
- Ignition switch OFF
- Lighting switch OFF

EXL-144
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal. A
• When in any of following conditions, follow me home function can be cancelled while follow me home func-
tion is operating.
Follow me home OFF condition B
- Ignition switch is turned from OFF→ACC or ON
- Lighting switch is turned from OFF→ON
NOTE: C
• Flash-to-pass operation illumination time for 1 time can be extended to approximately 30 seconds during
operation of follow me home function.
• Flash-to-pass operation can be illuminated continuously for approximately 60 seconds (flash-to-pass opera-
tion, 2 times), approximately 90 seconds (flash-to-pass operation, 3 times), and a maximum of approxi- D
mately 120 seconds (flash-to-pass operation, 4 times).
• Follow me home function activating time can be set by CONSULT. Refer to EXL-155, "HEADLAMP : CON-
SULT Function (BCM - HEAD LAMP) (India Production For Europe and General Areas)"(with Intelligent E
Key), EXL-159, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (India Production For Europe and
General Areas)"(without Intelligent Key).
HEADLAMP SYSTEM : Fail-Safe INFOID:0000000006841063 F

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN G
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM
H
Control part Fail-safe operation
• Turns ON the headlamp low relay when the ignition switch is turned ON
Headlamp • Turns OFF the headlamp low relay when the ignition switch is turned OFF I
• Headlamp high relay OFF

AUTO LIGHT SYSTEM

J
AUTO LIGHT SYSTEM : System Diagram INFOID:0000000006756547

WITHOUT DAYTIME RUNNING LIGHT SYSTEM K

EXL

JMLIA1625GB

EXL-145
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
WITH DAYTIME RUNNING LIGHT SYSTEM

JMLIA2203GB

AUTO LIGHT SYSTEM : System Description INFOID:0000000006756548

OUTLINE
• Auto light system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function
- Auto light function
Control by IPDM E/R
- Relay control function
• Auto light function turns the exterior lamps* ON/OFF automatically according to the outside brightness.
*: Headlamp (LO/HI), parking, license plate and tail lamps (Headlamp HI depends on the combination switch
condition.)
AUTO LIGHT FUNCTION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM detects the engine condition by the engine status signal or stop/start status signal* received from ECM
via CAN communication.
• BCM receives exterior lamp ON/OFF requests from the light & rain sensor by light & rain sensor serial link.
• BCM judges the ON/OFF status of the exterior lamp according to ON/OFF requests from light & rain sensor
and the vehicle condition.
• BCM transmits each request signal to IPDM E/R via CAN communication according to ON/OFF condition by
the auto light function.
*: With Stop/Start system
NOTE:
ON/OFF timing differs based on the sensitivity from the setting. The setting can be set by CONSULT. Refer to
EXL-155, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (India Production For Europe and General
Areas)"(with Intelligent Key), EXL-159, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (India Pro-
duction For Europe and General Areas)"(without Intelligent Key).
DAYTIME RUNNING LIGHT SYSTEM

EXL-146
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
DAYTIME RUNNING LIGHT SYSTEM : System Diagram INFOID:0000000006756551

E
JMLIA2202GB

DAYTIME RUNNING LIGHT SYSTEM : System Description INFOID:0000000006756552

F

OUTLINE
• Turns the following exterior lamps ON as the daytime running light. G
- Headlamp (LO)
- Parking, license plate and tail lamps.
• Daytime running light is controlled by daytime running light control function and combination switch reading H
function of BCM, and relay control function of IPDM E/R.
DAYTIME RUNNING LIGHT OPERATION
• BCM detects the combination switch condition by the combination switch reading function. I
• BCM detects vehicle condition depending on the following signals.
- Engine status signal or stop/start status signal* (received from ECM via CAN communication)
• BCM transmits the low beam request signal and daytime running light request signal to IPDM E/R via CAN J
communication according to the daytime running light ON condition.
Daytime running light ON condition
- Engine running or Stop/Start system activating* K
- Lighting switch OFF
- Auto light switch is ON, front fog lamp switch and rear fog lamp switch are OFF, and auto light judgement is
OFF.
EXL
• IPDM E/R turns the headlamp low relay, tail lamp RH relay and tail lamp LH relay ON according to the low
beam request signal and daytime running light request signal. And it turns each lamp ON.
*: With Stop/Start system
HEADLAMP AIMING CONTROL (MANUAL) M

HEADLAMP AIMING CONTROL (MANUAL) : System Description INFOID:0000000006765884

N
The headlamp levelizer adjusts the headlamp light axis upward and downward with the aiming motor inte-
grated in the front combination lamp.
FRONT FOG LAMP SYSTEM O

EXL-147
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
FRONT FOG LAMP SYSTEM : System Diagram INFOID:0000000006765878

JMLIA0970GB

FRONT FOG LAMP SYSTEM : System Description INFOID:0000000006765879

OUTLINE
Front fog lamp is controlled by combination switch reading function and front fog lamp control function of BCM,
and relay control function of IPDM E/R.
FRONT FOG LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front fog light request signal to IPDM E/R and the combination meter via CAN communi-
cation according to the front fog lamp ON condition.
Front fog lamp ON condition
- Front fog lamp switch ON and any of the following.
• Lighting switch 1ST
• Lighting switch 2ND
• Lighting switch AUTO and the ignition switch ON
IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the front
fog light request signal.
Combination meter turns the front fog lamp indicator lamp ON according to the front fog light request signal.
FRONT FOG LAMP SYSTEM : Fail-Safe INFOID:0000000006841064

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM

Control part Fail-safe operation

Front fog lamps Front fog lamp relay OFF

REAR FOG LAMP SYSTEM

EXL-148
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
REAR FOG LAMP SYSTEM : System Diagram INFOID:0000000006765880

E
JPLIA0179GB

REAR FOG LAMP SYSTEM : System Description INFOID:0000000006765881

F

OUTLINE
Rear fog lamp is controlled with the combination switch reading function and the rear fog lamp control function G
of BCM.
REAR FOG LAMP OPERATION H
• BCM detects the condition of the combination switch by the combination switch reading function.
• BCM supplies voltage to rear fog lamp according to the rear fog lamp ON condition.
Rear fog lamp switch is turned from OFF to ON with any of following condition. I
- Lighting switch 2ND
- Lighting switch AUTO and the ignition switch ON
- Front fog lamp ON
• BCM transmits the rear fog lamp status signal to the combination meter using CAN communication. J
• Combination meter turns the rear fog lamp indicator lamp ON according to the rear fog lamp status signal.
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM
K
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram
INFOID:0000000006765882

EXL

P
JPLIA0180GB

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description

INFOID:0000000006756560

OUTLINE

EXL-149
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the
flasher control function of BCM.
TURN SIGNAL LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn
signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION
BCM supplies voltage to both turn signal lamp circuit when the hazard switch is ON. BCM blinks the hazard
warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL OPERATION
• BCM transmits the turn signal indicator lamp signal to the combination meter using CAN communication
while the turn signal lamp and the hazard warning lamp are operating.
• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn signal indicator lamp signal.
3-TIME FLASHER FUNCTION
• By a short touch of the turn signal lever, BCM blinks the turn signal lamps 3 times in the selected direction.
• Cancel the operation when short touch of the turn signal lever in the reverse direction during the 3-time
flasher function operating.
HIGH FLASHER OPERATION
• BCM detects the turn signal lamp circuit status from the current value.
• BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn sig-
nal lamp operating.
NOTE:
The blinking speed is normal while operating the hazard warning lamp.
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : System Diagram INFOID:0000000006766824

WITHOUT DAYTIME RUNNING LIGHT SYSTEM

JMLIA1627GB

EXL-150
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
WITH DAYTIME RUNNING LIGHT SYSTEM
A

E
JMLIA1628GB

PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : System Description F

INFOID:0000000006766833

OUTLINE
Parking, license plate and tail lamps are controlled by combination switch reading function and headlamp con- G
trol function of BCM, and relay control function of IPDM E/R.
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION H
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal*1 or daytime running light request signal*2 to IPDM E/R via
CAN communication according to the ON/OFF condition of the parking, license plate and tail lamps.
I
Parking, license plate and tail lamps ON condition
- Lighting switch 1ST
- Lighting switch 2ND J
- Lighting switch AUTO, and the auto light function ON judgment
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON
• IPDM E/R turns the tail lamp relay, tail lamp RH relay, and tail lamp LH relay ON according to the position
light request signal*1 or daytime running light request signal*2, The parking, license plate and tail lamps turn K
ON.
*1: Without daytime running light system
*2: With daytime running light system EXL
NOTE:
For models with daytime running light, tail lamp relay is not used for exterior lamp.
M
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : Fail-Safe INFOID:0000000006841066

CAN COMMUNICATION CONTROL

N
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM O

Control part Fail-safe operation

• Parking lamp P
• License plate lamp • Turns ON the tail lamp relay when the ignition switch is turned ON
• Illumination • Turns OFF the tail lamp relay when the ignition switch is turned OFF
• Tail lamp

EXTERIOR LAMP BATTERY SAVER SYSTEM

EXL-151
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
EXTERIOR LAMP BATTERY SAVER SYSTEM : System Diagram INFOID:0000000006756567

WITHOUT DAYTIME RUNNING LIGHT SYSTEM

JMLIA1630GB

WITH DAYTIME RUNNING LIGHT SYSTEM

JMLIA1629GB

EXTERIOR LAMP BATTERY SAVER SYSTEM : System Description INFOID:0000000006756568

OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function
Control by IPDM E/R
- Relay control function
• BCM turns the exterior lamps* OFF after a period of time to prevent the battery from over-discharge when
the ignition switch is turned OFF with the exterior lamps ON.
*: Headlamp (LO/HI), parking lamp, tail lamp, license plate lamp, front fog lamp and rear fog lamp
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM turns the exterior lamps OFF (battery saver is activated) when all of the following conditions are satisfied.
• Exterior lamps ON
• When any of the following conditions is satisfied.
- Driver side door switch is turned from OFF to ON while ignition switch is OFF.
- Ignition switch is turned from ON to OFF while driver side door switch is ON.
NOTE:
When following condition (after the exterior lamp battery saver is activated), exterior lamps can be turned ON.

EXL-152
 SYSTEM
< SYSTEM DESCRIPTION > [TYPE 2]
• Lighting switch ON→ OFF → ON
A

EXL

EXL-153
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000006841060

APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.

Diagnosis mode Function Description

Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing BCM.

SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
• Automatic air conditioner
AIR CONDITONER × ×*1
• Manual air conditioner
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW ×
Body control system BCM ×
NATS IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Back door TRUNK ×
Theft warning alarm THEFT ALM × × ×
— RETAINED PWR*2 ×
Signal buffer system SIGNAL BUFFER × ×

NOTE:
• *1: For models with automatic air conditioner, this mode is not used.
• *2: This item is displayed, but is not used.

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.

EXL-154
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]

CONSULT screen item Indication/Unit Description A

Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected
While turning BCM status from low power consumption mode to
B
SLEEP>LOCK
normal mode (Power supply position is “LOCK”)
While turning BCM status from low power consumption mode to
SLEEP>OFF C
normal mode (Power supply position is “OFF”.)
LOCK>ACC While turning power supply position from “LOCK” to “ACC”
ACC>ON While turning power supply position from “ACC” to “IGN”
D
While turning power supply position from “RUN” to “ACC” (Vehicle
RUN>ACC
is stopping and selector lever is except P position.)
While turning power supply position from “CRANKING” to “RUN”
CRANK>RUN E
(From cranking up the engine to run it)
While turning power supply position from “RUN“ to “ACC” (Emer-
RUN>URGENT
gency stop operation)
F
ACC>OFF While turning power supply position from “ACC” to “OFF”
OFF>LOCK While turning power supply position from “OFF” to “LOCK”
Power position status of
OFF>ACC While turning power supply position from “OFF” to “ACC” G
Vehicle Condition the moment a particular
ON>CRANK DTC is detected While turning power supply position from “IGN” to “CRANKING”
While turning BCM status from normal mode (Power supply posi-
OFF>SLEEP
tion is “OFF”.) to low power consumption mode H
While turning BCM status from normal mode (Power supply posi-
LOCK>SLEEP
tion is “LOCK”.) to low power consumption mode
Power supply position is “LOCK” (Ignition switch OFF with steer- I
LOCK
ing is locked.)
Power supply position is “OFF” (Ignition switch OFF with steering
OFF
is unlocked.) J
ACC Power supply position is “ACC” (Ignition switch ACC)
Power supply position is “IGN” (Ignition switch ON with engine
ON
stopped) K
Power supply position is “RUN” (Ignition switch ON with engine
ENGINE RUN
running)
CRANKING Power supply position is “CRANKING” (At engine cranking) EXL
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
IGN Counter 0 - 39 • The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition M
whenever ignition switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

HEADLAMP N

HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (India Production For Europe
and General Areas) INFOID:0000000006756572 O

WORK SUPPORT
P

EXL-155
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]

Service item Setting item Setting

MODE 1*2 Normal

More sensitive setting than normal setting (Turns ON earlier than normal opera-
MODE 2
CUSTOM A/LIGHT SET- tion.)
TING*1 MODE 3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
Without twilight ON custom & less sensitive setting than normal setting (Turns ON
MODE 4
later than normal operation.)

On*2 With the exterior lamp battery saver function

BATTERY SAVER SET
Off Without the exterior lamp battery saver function
MODE 1 10 sec.
HEAD LIGHT TIMER Sets follow me home function activating time
MODE 2*2 30 sec.

*1: For models with auto light system, this item is operated.
*2: Factory setting
DATA MONITOR

Monitor item
Description
[Unit]
PUSH SW
The switch status input from push-button ignition switch
[On/Off]
ENGINE STATE
The engine status received from ECM via CAN communication
[Stop/Stall/Crank/Run]
VEH SPEED 1 The value of the vehicle speed received from combination meter via CAN communi-
[km/h] cation
TURN SIGNAL R
[On/Off]
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
[On/Off]
FR FOG SW
[On/Off]
RR FOG SW
[On/Off]
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL
The switch status input from rear door switch LH
[On/Off]

EXL-156
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
Monitor item
Description
[Unit] A
DOOR SW-BK
The switch status input from back door switch
[On/Off]
OPTICAL SENSOR* B
The sensor condition received from light & rain sensor
[On/Off/NG]
OPTI SEN (DTCT)
[V] NOTE: C
OPTI SEN (FILT) The item is indicated, but not monitored
[V]
*: For models with auto light system, this item is displayed. D

ACTIVE TEST
E
Test item Operation Description
Transmits the position light request signal to IPDM E/R via CAN commu-
On
TAIL LAMP nication to turn the tail lamp ON.
F
Off Stops the tail lamp request signal transmission.
Transmits the high beam request signal via CAN communication to turn
Hi
the headlamp (HI).
G
HEAD LAMP Transmits the low beam request signal via CAN communication to turn
Lo
the headlamp (LO).
Off Stops the high & low beam request signal transmission. H
Transmits the front fog lights request signal to IPDM E/R via CAN com-
On
FR FOG LAMP*1 munication to turn the front fog lamp ON.
Off Stops the front fog lights request signal transmission. I
• Outputs voltage to turn the rear fog lamp ON.
On • Transmits the rear fog lights request signal to combination meter via
RR FOG LAMP CAN communication to turn the rear fog lamp indicator lamp ON.
J
• Stops the voltage to turn the rear fog lamp OFF.
Off
• Stops the rear fog lamp status signal transmission.
Transmits the daytime running light request signal via CAN communica- K
On
DAYTIME RUNNING LIGHT*2 tion to turn the parking, license plate and tail lamps ON.
Off Stop the daytime running light request signal transmission.
*1 EXL
: For models with front fog lamp system, this item is tested.
*2
: For models with daytime running light system, this item is displayed.
FLASHER
M
FLASHER : CONSULT Function (BCM - FLASHER) (India Production For Europe and
General Areas) INFOID:0000000006756573

N
WORK SUPPORT

Service item Setting item Setting O

Lock Only With locking only
Unlk Only With unlocking only Sets the hazard warning lamp answer back function
HAZARD ANSWER P
when the door is lock/unlock with the door request switch
BACK Lock&Unlk* With locking/unlocking and Intelligent Key.
Off Without the function
*: Factory setting
DATA MONITOR

EXL-157
 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]

Monitor item
Description
[Unit]
REQ SW-DR
The switch status input from the request switch (driver side)
[On/Off]
REQ SW-AS
The switch status input from the request switch (passenger side)
[On/Off]
PUSH SW
The switch status input from the push-button ignition switch
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch
[On/Off]
RKE-LOCK
Lock signal status received from the remote keyless entry receiver
[On/Off]
RKE-UNLOCK
Unlock signal status received from the remote keyless entry receiver
[On/Off]
RKE-PANIC NOTE:
[On/Off] The item is indicated, but not monitored

ACTIVE TEST

Test item Operation Description

RH Outputs the voltage to blink the right side turn signal lamps
FLASHER LH Outputs the voltage to blink the left side turn signal lamps
Off Stops the voltage to turn the turn signal lamps OFF

EXL-158
 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000006841061
B
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
D
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
Data Monitor The BCM input/output signals are displayed. E
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
• Read and save the vehicle specification. F
Configuration
• Write the vehicle specification when replacing BCM.

SYSTEM APPLICATION
G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item H
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
I
Door lock DOOR LOCK × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
K

Wiper and washer WIPER × × ×

Turn signal and hazard warning lamps FLASHER × × EXL
• Automatic air conditioner
AIR CONDITONER ×
• Manual air conditioner
Combination switch COMB SW × M
Body control system BCM ×
NATS IMMU ×
Interior room lamp battery saver BATTERY SAVER × × N
Back door TRUNK ×
Theft warning alarm THEFT ALM*1 × × O
— RETAINED PWR*2
Signal buffer system SIGNAL BUFFER × ×
P
Panic alarm PANIC ALARM ×

• *1: For models without theft warning alarm this mode is not used.
• *2: This item is displayed, but is not used.
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (India Production For Europe

EXL-159
 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
and General Areas) INFOID:0000000006756575

WORK SUPPORT

Service item Setting item Setting

MODE 1*2 Normal

More sensitive setting than normal setting (Turns ON earlier than normal opera-
MODE 2
CUSTOM A/LIGHT SET- tion.)
TING*1 MODE 3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
Without twilight ON custom & less sensitive setting than normal setting (Turns ON
MODE 4
later than normal operation.)

On*2 With the exterior lamp battery saver function

BATTERY SAVER SET
Off Without the exterior lamp battery saver function
MODE 1 10 sec.
HEAD LIGHT TIMER Sets follow me home function activating time
MODE 2*2 30 sec.

*1: For models with auto light system, this item is displayed.
*2: Factory setting
DATA MONITOR

Monitor item
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
ACC SW
Ignition switch (ACC) status judged from ACC signal (ACC power supply)
[On/Off]
VEH SPEED The value of the vehicle speed received from combination meter with CAN commu-
[km/h] nication
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off] Each switch status that BCM judges from the combination switch reading function

FR FOG SW*1
[On/Off]

AUTO LIGHT SW*2

[On/Off]
RR FOG SW
[On/Off]
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL
The switch status input from rear door switch LH
[On/Off]
BACK DOOR SW
The switch status input from back door switch
[On/Off]

EXL-160
 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
Monitor item
Description
[Unit] A
TURN SIGNAL R
[On/Off]
TURN SIGNAL L B
Each switch status that BCM judges from the combination switch reading function
[On/Off]
TAIL LAMP SW
[On/Off] C
KEY ON SW
The switch status input from key on switch
[On/Off]
KEYLESS LOCK Lock signal status received from remote keyless entry receiver (integrated in the D
[On/Off] BCM)
PKB SW The parking brake switch status received from combination meter with CAN commu-
[On/Off] nication E
ENGINE RUN
The engine status received from ECM with CAN communication
[On/Off]

LIG SEN COND*2 The sensor condition received from light & rain sensor
F
[On/Off/NG]

*1: For models with front fog lamp system, this item is monitored.
*2: For models with auto light system, this item is monitored.
G

ACTIVE TEST
H
Test item Operation Description
Transmits the position light request signal to IPDM E/R with CAN com-
On
TAIL LAMP munication to turn the tail lamp ON. I
Off Stops the tail lamp request signal transmission.
Transmits the high beam request signal with CAN communication to turn
Hi
the headlamp (HI). J
HEAD LAMP Transmits the low beam request signal with CAN communication to turn
Lo
the headlamp (LO).
Off Stops the high & low beam request signal transmission. K
Transmits the front fog lights request signal to IPDM E/R with CAN com-
On
FR FOG LAMP*1 munication to turn the front fog lamp ON.
Off Stops the front fog lights request signal transmission. EXL
• Outputs the voltage to turn the rear fog lamp ON.
On • Transmits the rear fog lamp status signal to the combination meter with
RR FOG LAMP CAN communication to turn the rear fog lamp indicator lamp ON. M
• Stops the voltage to turn the rear fog lamp OFF.
Off
• Stops the rear fog lamp status signal transmission.
Transmits the daytime running light request signal via CAN communica- N
On
DAYTIME RUNNING LIGHT*2 tion to turn the parking, license plate and tail lamps ON.
Off Stop the daytime running light request signal transmission.
O
*1: For models with front fog lamp, this item is displayed but active test is not operated.
*2: For models with daytime running light system, this item is displayed.
FLASHER P
FLASHER : CONSULT Function (BCM - FLASHER) (India Production For Europe and
General Areas) INFOID:0000000006756576

DATA MONITOR

EXL-161
 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]

Monitor item
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch
[On/Off]

ACTIVE TEST

Test item Operation Description

RH Outputs the voltage to blink the right side turn signal lamps.
FLASHER LH Outputs the voltage to blink the left side turn signal lamps.
Off Stops the voltage to turn the turn signal lamps OFF.

EXL-162
 DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
A
Diagnosis Description INFOID:0000000006841055

AUTO ACTIVE TEST B

Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp C
• Front wiper (LO, HI)
• Parking lamp
• License plate lamp D
• Tail lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch) E
• Cooling fan
Operation Procedure
NOTE: F
Never perform auto active test in the following conditions.
• CONSULT is connected
• Passenger door is open G
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE: H
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the I
ignition switch OFF.
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts. J
NOTE:
• Engine starts when ignition switch is turned ON while brake pedal is depressed.
• Only a vehicle with the vehicle security system, the horn sounds.
K
5. The oil pressure warning lamp starts blinking when the auto active test starts.
6. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE: EXL
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK-114,
"Component Function Check".
M
Inspection in Auto Active Test
When auto active test is actuated, the following operation sequence is repeated 3 times.

Operation N
Inspection location Operation
sequence
1 Oil pressure warning lamp Blinks continuously during operation of auto active test
O
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamp
• License plate lamp
3 10 seconds P
• Tail lamp
• Front fog lamp
4 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
6 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds

EXL-163
 DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
Concept of Auto Active Test

JMMIA0354GB

• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis Chart in Auto Active Test

Symptom Inspection contents Possible cause

Any of the following components do not operate YES BCM signal input circuit
• Parking lamp
• License plate lamp Perform auto active test. • Lamp or motor
• Tail lamp Does the applicable system • Lamp or motor ground circuit
• Front fog lamp operate? NO • Harness or connector between
• Headlamp (HI, LO) IPDM E/R and applicable system
• Front wiper (HI, LO) • IPDM E/R

• BCM signal input circuit

• CAN communication signal be-
YES tween BCM and ECM
Perform auto active test. • CAN communication signal be-
A/C compressor does not operate Does the magnet clutch oper- tween ECM and IPDM E/R
ate? • Magnet clutch
• Harness or connector between
NO
IPDM E/R and magnet clutch
• IPDM E/R
• Harness or connector between
IPDM E/R and oil pressure switch
YES
• Oil pressure switch
• IPDM E/R
Perform auto active test.
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal be-
lamp blink? tween IPDM E/R and BCM
• CAN communication signal be-
NO
tween BCM and combination
meter
• Combination meter
• ECM signal input circuit
YES • CAN communication signal be-
tween ECM and IPDM E/R
Perform auto active test.
Cooling fan does not operate • Cooling fan motor
Does the cooling fan operate?
• Harness or connector between
NO
IPDM E/R and cooling fan motor
• IPDM E/R

EXL-164
 DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
CONSULT Function (IPDM E/R) INFOID:0000000006841056

A
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
B
Diagnosis mode Description
Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R. C
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
D
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.

SELF DIAGNOSTIC RESULT

E
Refer to PCS-39, "DTC Index".
DATA MONITOR
Monitor item F

Monitor Item MAIN SIG-

Description
[Unit] NALS
G
MOTOR FAN REQ Displays the value of the cooling fan speed request signal received from ECM via
×
[1/2/3/4] CAN communication.
AC COMP REQ Displays the status of the A/C compressor request signal received from ECM via
× H
[Off/On] CAN communication.
TAIL&CLR REQ Displays the status of the position light request signal received from BCM via CAN
×
[Off/On] communication.
I
HL LO REQ Displays the status of the low beam request signal received from BCM via CAN
×
[Off/On] communication.
HL HI REQ Displays the status of the high beam request signal received from BCM via CAN
× J
[Off/On] communication.
FR FOG REQ Displays the status of the front fog light request signal received from BCM via CAN
×
[Off/On] communication.
FR WIP REQ Displays the status of the front wiper request signal received from BCM via CAN
K
×
[Stop/1LOW/Low/Hi] communication.
WIP AUTO STOP
× Displays the status of the front wiper stop position signal judged by IPDM E/R. EXL
[STOP P/ACT P]
WIP PROT
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[Off/BLOCK]
IGN RLY1 -REQ Displays the status of the ignition switch ON signal received from BCM via CAN M
[Off/On] communication.
IGN RLY
× Displays the status of the ignition relay judged by IPDM E/R.
[Off/On] N
PUSH SW
Displays the status of the push-button ignition switch judged by IPDM E/R.
[Off/On]
INTER/NP SW O
Displays the status of the shift position judged by IPDM E/R.
[Off/On]
ST RLY CONT Displays the status of the starter relay status signal received from BCM via CAN
[Off/On] communication. P
IHBT RLY -REQ Displays the status of the starter control relay signal received from BCM via CAN
[Off/On] communication.
ST/INHI RLY Displays the status of the starter relay and starter control relay judged by IPDM E/
[Off/ ST ON/INHI ON/UNKWN] R.
DETENT SW Displays the status of the A/T shift selector (detention switch)* judged by IPDM E/
[Off/On] R.

EXL-165
 DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
Monitor Item MAIN SIG-
Description
[Unit] NALS
S/L RLY -REQ Displays the status of the steering lock relay signal received from BCM via CAN
[Off/On] communication.
S/L STATE
Displays the status of the steering lock judged by IPDM E/R.
[LOCK/UNLK/UNKWN]
DTRL REQ Displays the status of the daytime running light request signal received from BCM
[Off/On] via CAN communication.
OIL P SW
Displays the status of the oil pressure switch judged by IPDM E/R.
[Open/Close]
HOOD SW
Displays the status of the hood switch judged by IPDM E/R.
[Off/On]
HL WASHER REQ NOTE:
[Off/On] This item is indicated, but not monitored.
THFT HRN REQ Displays the status of the theft warning horn request signal received from BCM via
[Off/On] CAN communication.
HORN CHIRP NOTE:
[Off/On] This item is indicated, but not monitored.
*: CVT shift selector (detention switch) for CVT models.
ACTIVE TEST
Test item

Test item Operation Description

HORN On Operates horn relay for 20 ms.
Off OFF
FRONT WIPER Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.
1 OFF
2 Operates the cooling fan relay (LO operation).
MOTOR FAN
3 Operates the cooling fan relay (MID operation).
4 Operates the cooling fan relay (HI operation).
NOTE:
HEAD LAMP WASHER Off
This item is indicated, but cannot be tested.
Off OFF
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates simultaneously the headlamp low relay and the headlamp high relay
Hi
at 1 second ON/OFF intervals.
Fog Operates the front fog lamp relay.

EXL-166
 DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYS-
A
TEM)
Diagnosis Description INFOID:0000000006841057
B
AUTO ACTIVE TEST
Description C
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Front wiper (LO, HI)
• Parking lamp D
• License plate lamp
• Tail lamp
• Headlamp (LO, HI) E
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure F
NOTE:
Never perform auto active test in the following conditions.
• CONSULT is connected
G
• Passenger door is open
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE: H
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the I
ignition switch OFF.
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts. J
NOTE:
Only a vehicle with the vehicle security system, the horn sounds.
5. The oil pressure warning lamp starts blinking when the auto active test starts. K
6. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF. EXL
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK-284,
"Component Function Check".
Inspection in Auto Active Test M
When auto active test is actuated, the following operation sequence is repeated 3 times.

Operation N
Inspection location Operation
sequence
1 Oil pressure warning lamp Blinks continuously during operation of auto active test
2 Front wiper LO for 5 seconds → HI for 5 seconds O
• Parking lamp
3 • License plate lamp 10 seconds
• Tail lamp P
4 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
6 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds

EXL-167
 DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
Concept of Auto Active Test

JMMIA0355GB

• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode

Symptom Inspection contents Possible cause

Any of the following components do not operate YES BCM signal input circuit
• Parking lamp • Lamp or motor
Perform auto active test.
• License plate lamp • Lamp or motor ground circuit
Does the applicable system
• Tail lamp NO • Harness or connector between
operate?
• Headlamp (HI, LO) IPDM E/R and applicable system
• Front wiper (HI, LO) • IPDM E/R
• BCM signal input circuit
• CAN communication signal be-
YES tween BCM and ECM
Perform auto active test. • CAN communication signal be-
A/C compressor does not operate Does the magnet clutch oper- tween ECM and IPDM E/R
ate? • Magnet clutch
• Harness or connector between
NO
IPDM E/R and magnet clutch
• IPDM E/R
• Harness or connector between
IPDM E/R and oil pressure
YES switch
• Oil pressure switch
Perform auto active test. • IPDM E/R
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal be-
lamp blink? tween IPDM E/R and BCM
• CAN communication signal be-
NO
tween BCM and combination
meter
• Combination meter
• ECM signal input circuit
YES • CAN communication signal be-
tween ECM and IPDM E/R
Perform auto active test.
Cooling fan does not operate • Cooling fan motor
Does the cooling fan operate?
• Harness or connector between
NO
IPDM E/R and cooling fan motor
• IPDM E/R

EXL-168
 DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
CONSULT Function (IPDM E/R) INFOID:0000000006841058

A
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
B
Diagnosis mode Description
Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R. C
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
D
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.

SELF DIAGNOSTIC RESULT

E
Refer to PCS-105, "DTC Index".
DATA MONITOR
Monitor item F

Monitor Item MAIN SIG-

Description
[Unit] NALS
G
MOTOR FAN REQ Displays the value of the cooling fan speed request signal received from ECM via
×
[1/2/3/4] CAN communication.
AC COMP REQ Displays the status of the A/C compressor request signal received from ECM via
× H
[Off/On] CAN communication.
TAIL&CLR REQ Displays the status of the position light request signal received from BCM via CAN
×
[Off/On] communication.
I
HL LO REQ Displays the status of the low beam request signal received from BCM via CAN
×
[Off/On] communication.
HL HI REQ Displays the status of the high beam request signal received from BCM via CAN
× J
[Off/On] communication.
FR FOG REQ Displays the status of the front fog light request signal received from BCM via CAN
×
[Off/On] communication.
FR WIP REQ Displays the status of the front wiper request signal received from BCM via CAN
K
×
[Stop/1LOW/Low/Hi] communication.
WIP AUTO STOP
× Displays the status of the front wiper stop position signal judged by IPDM E/R. EXL
[STOP P/ACT P]
WIP PROT
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[Off/BLOCK]
IGN RLY M
× Displays the status of the ignition relay judged by IPDM E/R.
[Off/On]
INTER/NP SW
Displays the status of the shift position judged by IPDM E/R.
[Off/On] N
ST RLY REQ Displays the status of the starter control relay signal received from BCM via CAN
[Off/On] communication.
DTRL REQ Displays the status of the daytime running light request signal received from BCM O
[Off/On] via CAN communication.
OIL P SW
Displays the status of the oil pressure switch judged by IPDM E/R.
[Open/Close] P
HOOD SW
Displays the status of the hood switch judged by IPDM E/R.
[Off/On]
HL WASHER REQ NOTE:
[Off/On] This item is indicated, but not monitored.
THFT HRN REQ Displays the status of the theft warning horn request signal received from BCM via
[Off/On] CAN communication.

EXL-169
 DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [TYPE 2]
Monitor Item MAIN SIG-
Description
[Unit] NALS
HORN CHIRP NOTE:
[Off/On] This item is indicated, but not monitored.
CRNRNG LMP REQ NOTE:
[Off/On] This item is indicated, but not monitored.

ACTIVE TEST
Test item

Test item Operation Description

HORN On Operates horn relay for 20 ms.
Off OFF
FRONT WIPER Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.
1 OFF
2 Operates the cooling fan relay (LO operation).
MOTOR FAN
3 Operates the cooling fan relay (MID operation).
4 Operates the cooling fan relay (HI operation).
NOTE:
HEAD LAMP WASHER Off
This item is indicated, but cannot be tested.
Off OFF
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates simultaneously the headlamp low relay and the headlamp high relay at
Hi
1 second ON/OFF intervals.
Fog Operates the front fog lamp relay.

EXL-170
 BCM, IPDM E/R
< ECU DIAGNOSIS INFORMATION > [TYPE 2]

ECU DIAGNOSIS INFORMATION A

BCM, IPDM E/R
List of ECU Reference INFOID:0000000006882467
B

WITH INTELLIGENT KEY

C
ECU Reference
BCS-57, "Reference Value (Type A)" *
BCS-79, "Reference Value (Type B)" * D
BCM BCS-149, "Fail-safe"
BCS-152, "DTC Inspection Priority Chart"
E
BCS-153, "DTC Index"
PCS-19, "Reference Value"
IPDM E/R PCS-38, "Fail-Safe" F
PCS-39, "DTC Index"
*: Regarding to the vehicle type, refer to BCS-57, "Application Notice".
G
WITHOUT INTELLIGENT KEY

ECU Reference
H
BCS-242, "Reference Value (Type A)" *
BCS-256, "Reference Value (Type B)" *
BCM BCS-301, "Fail-safe" I
BCS-302, "DTC Inspection Priority Chart"
BCS-302, "DTC Index"
J
PCS-86, "Reference Value"
IPDM E/R PCS-104, "Fail-Safe"
PCS-105, "DTC Index" K
*: Regarding to the vehicle type, refer to BCS-242, "Application Notice".

EXL

EXL-171
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

WIRING DIAGRAM
EXTERIOR LIGHTING SYSTEM
Application Notice INFOID:0000000007228621

Wiring diagram type Destination

• Models for Europe (Without Stop / Start System): Vehicle production: From July 2010 to June 2011
TYPE A
• Models for general area from India plant*
• Models for Europe (With Stop / Start System): Vehicle production: From July 2010 to June 2011
TYPE B
• Models for South Africa
• Models for Lebanon and Jordan
TYPE C
• Models for Europe: Vehicle production: From July 2011
*: Refer to GI-26, "Information About Identification or Model Code", “Information About Identification or Model
Code” to identify a production plant.
TYPE A

EXL-172
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]
TYPE A : Wiring Diagram INFOID:0000000006756582

EXL

JCLWM6031GB
P

EXL-173
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6032GB

EXL-174
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6033GB

EXL-175
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6034GB

EXL-176
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6035GB

EXL-177
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6036GB

EXL-178
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6037GB

EXL-179
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6038GB

EXL-180
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6039GB

EXL-181
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6040GB

EXL-182
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6041GB

EXL-183
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6042GB

EXL-184
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6043GB

EXL-185
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6044GB

EXL-186
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6045GB

EXL-187
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6046GB

EXL-188
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6047GB

EXL-189
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6048GB

TYPE B

EXL-190
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]
TYPE B : Wiring Diagram INFOID:0000000007228613

EXL

JCLWM6611GB
P

EXL-191
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6612GB

EXL-192
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6613GB

EXL-193
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWM6614GB

EXL-194
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWM6615GB

EXL-195
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWA5357GB

EXL-196
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWA5358GB

EXL-197
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWA5359GB

EXL-198
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWA5360GB

EXL-199
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWA5361GB

EXL-200
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWA5362GB

EXL-201
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JCLWA5363GB

EXL-202
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JCLWA5364GB

TYPE C P

EXL-203
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]
TYPE C : Wiring Diagram INFOID:0000000007640609

For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not
described in wiring diagram), refer to GI-12, "Connector Information".

JRLWC0713GB

EXL-204
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JRLWC0714GB

EXL-205
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JRLWC0715GB

EXL-206
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

EXL

JRLWC0716GB

EXL-207
 EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [TYPE 2]

JRLWC0717GB

EXL-208
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [TYPE 2]

BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000007618885
B

OVERALL SEQUENCE
C

EXL

JMKIA8652GB

DETAILED FLOW

EXL-209
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [TYPE 2]

1.GET INFORMATION FOR SYMPTOM

1. Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2. Check operation condition of the function that is malfunctioning.

>> GO TO 2.
2.CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is detected.
- Record DTC and freeze frame data (Print them out using CONSULT.)
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 5.
4.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to BCS-152, "DTC Inspection Priority Chart" [BCM (with Intelligent
Key)], BCS-302, "DTC Inspection Priority Chart" [BCM (without Intelligent Key)] and determine trouble diag-
nosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES >> GO TO 7.
NO >> Check according to GI-51, "Intermittent Incident".
6.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES >> GO TO 7.
NO >> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.

EXL-210
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [TYPE 2]

7.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE A

Inspect according to Diagnostic Procedure of the system.
Is malfunctioning part detected?
YES >> GO TO 8. B
NO >> Check according to GI-51, "Intermittent Incident".
8.REPAIR OR REPLACE THE MALFUNCTIONING PART
C
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is detected, erase it. D

>> GO TO 9.
E
9.FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely. F
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
G
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO >> Before returning the vehicle to the customer, always erase DTC.
H

EXL

EXL-211
 EXTERIOR LAMP FUSE
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]

DTC/CIRCUIT DIAGNOSIS
EXTERIOR LAMP FUSE
Diagnosis Procedure INFOID:0000000006765888

1.CHECK FUSE
Check that the following fuses are not fusing.
TYPE A
Unit Location Fuse No. Capacity
Headlamp HI (LH) IPDM E/R #45 10 A
Headlamp HI (RH) IPDM E/R #44 10 A
Headlamp LO (LH) IPDM E/R #42 15 A
Headlamp LO (RH) IPDM E/R #41 15 A
Front fog lamp Fuse and fusible link block #39 15 A
• Parking lamp
• Tail lamp (RH) IPDM E/R #46 10 A
• License plate lamp
With daytime running
Tail lamp (LH) — #31 10 A
light system
Without daytime running
Tail lamp (LH) — #36 10 A
light system
Stop lamp Fuse and fusible link block #38 10 A
IPDM E/R 1 10 A
#52*
Back-up lamp
— #5*2 10 A

*1: Except for M/T models

*2: For M/T models
TYPE B
Unit Location Fuse No. Capacity
Headlamp HI (LH) IPDM E/R #45 10 A
Headlamp HI (RH) IPDM E/R #44 10 A
Headlamp LO (LH) IPDM E/R #42 15 A
Headlamp LO (RH) IPDM E/R #41 15 A
Front fog lamp Fuse and fusible link block #39 15 A
• Parking lamp
• Tail lamp (RH) IPDM E/R #46 10 A
• License plate lamp
With daytime running light
Tail lamp (LH) — #31 10 A
system
Without daytime running
Tail lamp (LH) — #36 10 A
light system
Stop lamp Fuse and fusible link block #38 10 A

#5*1
Back-up lamp — #63*2 10 A

#64*3

*1: For M/T, without Stop/Start system models

*2: For CVT, via DC/DC converter
*3: For M/T, via DC/DC converter
Is the inspection result normal?
EXL-212
 EXTERIOR LAMP FUSE
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
YES >> The fuse is normal.
NO >> Repair the applicable circuit. And then replace the fuse. A

EXL

EXL-213
 HEADLAMP (HI) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
HEADLAMP (HI) CIRCUIT
Component Function Check INFOID:0000000006825085

1.CHECK HEADLAMP (HI) OPERATION

CONSULT ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the headlamp (HI) is turned ON.

Hi : Headlamp (HI) ON
Off : Headlamp (HI) OFF
NOTE:
ON/OFF is repeated 1 second each.
Is the inspection result normal?
YES >> Headlamp (HI) circuit is normal.
NO >> Refer to EXL-214, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006825086

1.CHECK HEADLAMP (HI) OUTPUT VOLTAGE

CONSULT ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect headlamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5. With operating the test items, check voltage between IPDM E/R harness connector and ground.

(+)
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal

RH Hi Battery voltage
63
Off 0V
E14 Ground EXTERNAL LAMPS
LH Hi Battery voltage
61
Off 0V
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (HI) OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector.

IPDM E/R Headlamp

Continuity
Connector Terminal Connector Terminal
RH 63 E45
E14 1 Existed
LH 61 E26
Is the inspection result normal?
YES >> Replace headlamp bulb.
NO >> Repair or replace harness.
3.CHECK HEADLAMP (HI) FUSE
1. Turn ignition switch OFF.

EXL-214
 HEADLAMP (HI) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
2. Check that the following fuses are not fusing.
A
Unit Location Fuse No. Capacity
Headlamp HI (RH) #44
IPDM E/R 10 A
Headlamp HI (LH) #45 B
Is the inspection result normal?
YES >> Replace IPDM E/R.
C
NO >> GO TO 4.
4.CHECK HEADLAMP HIGH (HI) SHORT CIRCUIT
1. Disconnect IPDM E/R connector. D
2. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R E
Continuity
Connector Terminal
Ground
RH 63
E14 Not existed
LH 61 F
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
G
NO >> Repair or replace harness. And then replace the fuse.

EXL

EXL-215
 HEADLAMP (LO) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
HEADLAMP (LO) CIRCUIT
Component Function Check INFOID:0000000006825087

1.CHECK HEADLAMP (LO) OPERATION

CONSULT ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the headlamp (LO) is turned ON.

Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF
Is the inspection result normal?
YES >> Headlamp (LO) is normal.
NO >> Refer to EXL-216, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006825088

1.CHECK HEADLAMP (LO) OUTPUT VOLTAGE

CONSULT ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect headlamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5. With operating the test items, check voltage between IPDM E/R harness connector and ground.

(+)
(−) Voltage
IPDM E/R Test item
(Approx.)
Connector Terminal
Lo Battery voltage
RH 40
Off 0V
E12 Ground EXTERNAL LAMPS
38*1 Lo Battery voltage
LH 2
39* Off 0V

*1: Without Stop/Start system models

*2: With Stop/Start system models
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (LO) OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector.

IPDM E/R Headlamp

Continuity
Connector Terminal Connector Terminal
RH 40 E45
E12 38*1 3 Existed
LH E26
39*2

*1: Without Stop/Start system models

*2: With Stop/Start system models
Is the inspection result normal?
YES >> Replace headlamp bulb.

EXL-216
 HEADLAMP (LO) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
NO >> Repair or replace harness.
3.CHECK HEADLAMP (LO) FUSE A

1. Turn ignition switch OFF.

2. Check that the following fuses are not fusing.
B
Unit Lotion Fuse No. Capacity
Headlamp LO (RH) #41
IPDM E/R 15 A C
Headlamp LO (LH) #42
Is the inspection result normal?
YES >> Replace IPDM E/R. D
NO >> GO TO 4.
4.CHECK HEADLAMP (LO) SHORT CIRCUIT
E
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R F
Continuity
Connector Terminal
RH 40 Ground
G
E12 38* 1 Not existed
LH
39*2

*1: Without Stop/Start system models H

*2: With Stop/Start system models
Is the inspection result normal?
I
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
J

EXL

EXL-217
 HEADLAMP GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
HEADLAMP GROUND CIRCUIT
Diagnosis Procedure INFOID:0000000006825091

1.CHECK HEADLAMP GROUND OPEN CIRCUIT

1. Turn ignition switch OFF.
2. Disconnect headlamp connector.
3. Check continuity between headlamp harness connector and ground.

Headlamp
Continuity
Connector Terminal
Ground
RH E45
2 Existed
LH E26
Is the inspection result normal?
YES >> Headlamp ground circuit is normal.
NO >> Repair or replace harness.

EXL-218
 HEADLAMP AIMING SYSTEM (MANUAL)
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
HEADLAMP AIMING SYSTEM (MANUAL)
A
Component Inspection INFOID:0000000006825092

1.CHECK HEADLAMP AIMING SWITCH B

1. Remove headlamp aiming switch.
2. Check resistance among each headlamp aiming switch terminal.
C
Headlamp aiming switch Condition Resistance
Terminal Switch position (Approx.)
D
0 A: 1000 Ω
1 B: 511 Ω
2
1 2 C: 348 Ω E
3 D: 240 Ω
3 — E: 390 Ω JSLIA0084ZZ

F
Is the inspection result normal?
YES >> Headlamp aiming switch is normal.
NO >> Replace the headlamp aiming switch.
G

EXL

EXL-219
 TAIL LAMP LH RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
TAIL LAMP LH RELAY CIRCUIT
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006825099

1.CHECK TAIL LAMP LH RELAY FUSE

1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.

Unit Fuse No. Capacity

#36
Tail lamp LH relay 10 A
#46
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK TAIL LAMP LH RELAY POWER SUPPLY CIRCUIT 1
1. Remove tail lamp LH relay.
2. Check voltage between tail lamp LH relay harness connector and ground.

(+)
Voltage
Tail lamp LH relay (–)
(Approx.)
Connector Terminal
E70 5 Ground Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK TAIL LAMP LH RELAY POWER SUPPLY CIRCUIT 2
CONSULT ACTIVE TEST
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
3. With operating the test items, check voltage between tail lamp LH relay harness connector and ground.

(+)
Voltage
Tail lamp LH relay (–) Test item
(Approx.)
Connector Terminal

EXTERNAL TAIL Battery voltage

E70 2 Ground
LAMPS Off 0V
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK TAIL LAMP LH RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and tail lamp LH relay harness connector.

IPDM E/R Tail lamp LH relay

Continuity
Connector Terminal Connector Terminal
E14 58 E70 2 Existed
Is the inspection result normal?
YES >> Replace IPDM E/R.
EXL-220
 TAIL LAMP LH RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
NO >> Repair or replace harness.
5.CHECK TAIL LAMP LH RELAY GROUND CIRCUIT A

1. Turn ignition switch OFF.

2. Check continuity between tail lamp LH relay harness connector and ground.
B
Tail lamp LH relay
Continuity
Connector Terminal Ground
C
E70 1 Existed
Is the inspection result normal?
YES >> GO TO 6. D
NO >> Repair or replace harness.
6.CHECK TAIL LAMP LH RELAY
E
Check tail lamp LH relay.
Refer to EXL-221, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Inspection"
Is the inspection result normal?
F
YES >> Tail lamp LH relay circuit is normal.
NO >> Replace tail lamp LH relay.
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Inspection INFOID:0000000006825100 G

1.CHECK TAIL LAMP LH RELAY

1. Turn ignition switch OFF. H
2. Remove tail lamp LH relay.
3. Check continuity between tail lamp LH relay terminals.
I
Terminal
Condition Continuity
tail lamp LH relay
12 V direct current supply between termi-
J
Existed
3 5 nals 1 and 2
No current supply Not existed
K
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace tail lamp LH relay.
SEF497Y EXL
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006825632
M

1.CHECK TAIL LAMP LH RELAY FUSE

1. Turn ignition switch OFF. N
2. Check that the following fuses are not fusing.

Unit Fuse No. Capacity

O
Tail lamp LH relay #46 10 A
Is the inspection result normal?
YES >> GO TO 2. P
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK TAIL LAMP LH RELAY POWER SUPPLY CIRCUIT
1. Remove tail lamp LH relay.
2. Check voltage between tail lamp LH relay harness connector and ground.

EXL-221
 TAIL LAMP LH RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]

(+)
Voltage
Tail lamp LH relay (–)
(Approx.)
Connector Terminal
2
E67 Ground Battery voltage
5
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.CHECK TAIL LAMP LH RELAY CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector and tail lamp LH relay harness connector.

IPDM E/R Tail lamp LH relay

Continuity
Connector Terminal Connector Terminal
2
E14 60 E67 Existed
5
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace harness.
4.CHECK TAIL LAMP LH RELAY CONTROL SIGNAL OUTPUT
CONSULT ACTIVE TEST
1. Install tail lamp LH relay.
2. Turn ignition switch ON.
3. Select “DAYTIME RUNNING LIGHT” of BCM (HEADLAMP) active test item.
4. With operating the test item, check voltage between IPDM E/R harness connector and ground.

(+)
Voltage
IPDM E/R (−)
Test item (Approx.)
Connector Terminal
On 0V
E10 19 Ground DAYTIME RUNNING LIGHT
Off Battery voltage
Is the inspection result normal?
YES >> GO TO 8.
NO-1(Fixed at 0 V)>>GO TO 6.
NO-2(Fixed at battery voltage) >>GO TO 5.
5.CHECK DAYTIME RUNNING LIGHT REQUEST SIGNAL
CONSULT DATA MONITOR
1. Select “DTRL REQ” of IPDM E/R data monitor item.
2. With operating the daytime running light, check the monitor status.

Monitor item Condition Monitor status

ON Condition On
DTRL REQ Daytime running light
OFF Condition Off
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
6.CHECK TAIL LAMP LH RELAY CONTROL SIGNAL OPEN CIRCUIT
EXL-222
 TAIL LAMP LH RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
1. Turn ignition switch OFF.
2. Remove tail lamp LH relay. A
3. Disconnect IPDM E/R harness connector.
4. Check continuity between IPDM E/R harness connector and tail lamp LH relay harness connector.
B
IPDM E/R Tail lamp LH relay
Continuity
Connector Terminal Connector Terminal
E10 19 E67 1 Existed C
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace harness. D
7.CHECK TAIL LAMP LH RELAY CONTROL SIGNAL SHORT CIRCUIT
1. Remove tail lamp RH relay. E
2. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R
Continuity F
Connector Terminal Ground
E10 19 Not existed
Is the inspection result normal? G
YES >> Replace IPDM E/R.
NO >> Repair or replace harness.
8.CHECK TAIL LAMP LH RELAY H

Check tail lamp LH relay.

Refer to EXL-223, "WITH DAYTIME RUNNING LIGHT SYSTEM : Component Inspection"
I
Is the inspection result normal?
YES >> Tail lamp LH relay circuit is normal.
NO >> Replace tail lamp LH relay.
J
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Inspection INFOID:0000000006825633

1.CHECK TAIL LAMP LH RELAY K

1. Turn ignition switch OFF.
2. Remove tail lamp LH relay.
3. Check continuity between tail lamp LH relay terminals. EXL

Terminal
Condition Continuity
tail lamp LH relay M
12 V direct current supply between termi-
Existed
3 5 nals 1 and 2
No current supply Not existed N

Is the inspection result normal?

YES >> INSPECTION END O
NO >> Replace tail lamp LH relay.
SEF497Y

EXL-223
 TAIL LAMP RH RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
TAIL LAMP RH RELAY CIRCUIT
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006825645

1.CHECK TAIL LAMP RH RELAY FUSE

1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.

Unit Fuse No. Capacity

#31
Tail lamp RH relay 10 A
#46
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK TAIL LAMP RH RELAY POWER SUPPLY CIRCUIT 1
1. Remove tail lamp RH relay.
2. Check voltage between tail lamp RH relay harness connector and ground.

(+)
Voltage
Tail lamp RH relay (–)
(Approx.)
Connector Terminal
E71 5 Ground Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK TAIL LAMP RH RELAY POWER SUPPLY CIRCUIT 2
CONSULT ACTIVE TEST
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
3. With operating the test items, check voltage between tail lamp RH relay harness connector and ground.

(+)
Voltage
Tail lamp RH relay (–) Test item
(Approx.)
Connector Terminal

EXTERNAL TAIL Battery voltage

E71 2 Ground
LAMPS Off 0V
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK TAIL LAMP RH RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and tail lamp RH relay harness connector.

IPDM E/R Tail lamp RH relay

Continuity
Connector Terminal Connector Terminal
E14 59 E71 2 Existed
Is the inspection result normal?
YES >> Replace IPDM E/R.
EXL-224
 TAIL LAMP RH RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
NO >> Repair or replace harness.
5.CHECK TAIL LAMP RH RELAY GROUND CIRCUIT A

1. Turn ignition switch OFF.

2. Check continuity between tail lamp RH relay harness connector and ground.
B
Tail lamp RH relay
Continuity
Connector Terminal Ground
C
E71 1 Existed
Is the inspection result normal?
YES >> GO TO 6. D
NO >> Repair or replace harness.
6.CHECK TAIL LAMP RH RELAY
E
Check tail lamp RH relay.
Refer to EXL-227, "WITH DAYTIME RUNNING LIGHT SYSTEM : Component Inspection"
Is the inspection result normal?
F
YES >> Tail lamp RH relay circuit is normal.
NO >> Replace tail lamp RH relay.
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Inspection INFOID:0000000006825646 G

1.CHECK TAIL LAMP RH RELAY

1. Turn ignition switch OFF. H
2. Remove tail lamp RH relay.
3. Check continuity between tail lamp RH relay terminals.
I
Terminal
Condition Continuity
tail lamp RH relay
12 V direct current supply between termi-
J
Existed
3 5 nals 1 and 2
No current supply Not existed
K
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace tail lamp RH relay.
SEF497Y EXL
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006825650
M

1.CHECK TAIL LAMP RH RELAY FUSE

1. Turn ignition switch OFF. N
2. Check that the following fuses are not fusing.

Unit Fuse No. Capacity

O
Tail lamp RH relay #31 10 A
Is the inspection result normal?
YES >> GO TO 2. P
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK TAIL LAMP RH RELAY CONTROL SIGNAL OUTPUT
CONSULT ACTIVE TEST
1. Install tail lamp RH relay.
2. Turn ignition switch ON.
3. Select “DAYTIME RUNNING LIGHT” of BCM (HEADLAMP) active test item.

EXL-225
 TAIL LAMP RH RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
4. With operating the test item, check voltage between IPDM E/R harness connector and ground.

(+)
Voltage
IPDM E/R (−)
Test item (Approx.)
Connector Terminal
On 0V
E10 19 Ground DAYTIME RUNNING LIGHT
Off Battery voltage
Is the inspection result normal?
YES >> GO TO 6.
NO-1(Fixed at 0 V)>>GO TO 4.
NO-2(Fixed at battery voltage) >>GO TO 3.
3.CHECK DAYTIME RUNNING LIGHT REQUEST SIGNAL
CONSULT DATA MONITOR
1. Select “DTRL REQ” of IPDM E/R data monitor item.
2. With operating the daytime running light, check the monitor status.

Monitor item Condition Monitor status

ON Condition On
DTRL REQ Daytime running light
OFF Condition Off
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
4.CHECK TAIL LAMP RH RELAY CONTROL SIGNAL OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove tail lamp RH relay.
3. Disconnect IPDM E/R harness connector.
4. Check continuity between IPDM E/R harness connector and tail lamp RH relay harness connector.

IPDM E/R Tail lamp RH relay

Continuity
Connector Terminal Connector Terminal
E10 19 E71 1 Existed
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
5.CHECK TAIL LAMP RH RELAY CONTROL SIGNAL SHORT CIRCUIT
1. Remove tail lamp LH relay.
2. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R
Continuity
Connector Terminal Ground
E10 19 Not existed
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace harness.
6.CHECK TAIL LAMP RH RELAY
Check tail lamp RH relay.
Refer to EXL-227, "WITH DAYTIME RUNNING LIGHT SYSTEM : Component Inspection"
Is the inspection result normal?
YES >> Tail lamp RH relay circuit is normal.

EXL-226
 TAIL LAMP RH RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
NO >> Replace tail lamp RH relay.
A
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Inspection INFOID:0000000006825651

1.CHECK TAIL LAMP RH RELAY B

1. Turn ignition switch OFF.
2. Remove tail lamp RH relay.
3. Check continuity between tail lamp RH relay terminals.
C

Terminal
Condition Continuity
tail lamp RH relay D
12 V direct current supply between termi-
Existed
3 5 nals 1 and 2
No current supply Not existed E
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace tail lamp RH relay. F
SEF497Y

EXL

EXL-227
 PARKING LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
PARKING LAMP CIRCUIT
Component Function Check INFOID:0000000006765901

NOTE:
Check tail lamp RH and LH relay circuit first if the parking lamp, the tail lamp, and the license plate lamp are
not turned ON.
• Tail lamp RH relay circuit: Refer to EXL-224, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis
Procedure" (without daytime running light), EXL-225, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag-
nosis Procedure" (with daytime running light).
• Tail lamp LH relay circuit: Refer to EXL-220, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis
Procedure" (without daytime running light), EXL-221, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag-
nosis Procedure" (with daytime running light).
1.CHECK PARKING LAMP OPERATION
CONSULT ACTIVE TEST
1. Select “TAIL LAMP” or “DAYTIME RUNNING LIGHT” of BCM(HEADLAMP) active test item.
2. With operating the test items, check that the parking lamp is turned ON.

On : Parking lamp ON
Off : Parking lamp OFF
Is the inspection result normal?
YES >> Parking lamp circuit is normal.
NO >> Refer to EXL-228, "Diagnosis Procedure".
NOTE:
For active test items of models with daytime running light, use “DAYTIME RUNNING LIGHT”.
Diagnosis Procedure INFOID:0000000006765902

1.CHECK PARKING LAMP BULB

Check the applicable lamp bulb.
Is the bulb normal?
YES >> GO TO 2.
NO >> Replace the bulb.
2.CHECK PARKING LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove tail lamp RH relay.
3. Check continuity between tail lamp RH relay harness connector and parking lamp harness connector.

Tail lamp RH relay Parking lamp

Continuity
Connector Terminal Connector Terminal
RH E43
E71 3 1 Existed
LH E24
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between parking lamp harness connector and ground.

Parking lamp
Continuity
Connector Terminal
Ground
RH E43
2 Existed
LH E24

EXL-228
 PARKING LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary. A
NO >> Repair or replace harness.

EXL

EXL-229
 TAIL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
TAIL LAMP CIRCUIT
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006826719

NOTE:
Check tail lamp RH and LH relay circuit first if the parking lamp, the tail lamp, and the license plate lamp are
not turned ON.
• Tail lamp RH relay circuit: Refer to EXL-224, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis
Procedure" (without daytime running light), EXL-225, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag-
nosis Procedure" (with daytime running light).
• Tail lamp LH relay circuit: Refer to EXL-220, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis
Procedure" (without daytime running light), EXL-221, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag-
nosis Procedure" (with daytime running light).
1.CHECK TAIL LAMP OPERATION
CONSULT ACTIVE TEST
1. Select “TAIL LAMP” of BCM(HEADLAMP) active test item.
2. With operating the test items, check that the tail lamp is turned ON.

ON : Tail Lamp ON
Off : Tail lamp OFF
Is the inspection result normal?
YES >> Tail lamp circuit is normal.
NO >> Refer to EXL-230, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006826720

1.CHECK TAIL LAMP BULB

Check the applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK TAIL LAMP OPERATION
Check that the tail lamp is turned ON.
Which tail lamp does not turn ON?
RH >> GO TO 3.
LH >> GO TO 4.
3.CHECK TAIL LAMP RH OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove tail lamp RH relay.
3. Disconnect rear combination lamp RH connector.
4. Check continuity between tail lamp RH relay harness connector and rear combination lamp RH harness
connector.

Tail lamp RH relay Rear combination lamp RH

Continuity
Connector Terminal Connector Terminal
E71 3 B59 6 Existed
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
4.CHECK TAIL LAMP LH OPEN CIRCUIT
1. Turn ignition switch OFF.
EXL-230
 TAIL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
2. Remove tail lamp LH relay.
3. Disconnect rear combination lamp LH connector. A
4. Check continuity between tail lamp LH relay harness connector and rear combination lamp LH harness
connector.
B
Tail lamp LH relay Rear combination lamp LH
Continuity
Connector Terminal Connector Terminal
E70 3 B80 6 Existed C
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness. D
5.CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground. E

Rear combination lamp

Continuity
Connector Terminal
Ground F
RH B59
3 Existed
LH B80
Is the inspection result normal? G
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
WITH DAYTIME RUNNING LIGHT SYSTEM H

WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check INFOID:0000000006756603

I
NOTE:
Check tail lamp RH and LH relay circuit first if the parking lamp, the tail lamp, and the license plate lamp are
not turned ON.
• Tail lamp RH relay circuit: Refer to EXL-224, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis J
Procedure" (without daytime running light), EXL-225, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag-
nosis Procedure" (with daytime running light).
• Tail lamp LH relay circuit: Refer to EXL-220, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis K
Procedure" (without daytime running light), EXL-221, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag-
nosis Procedure" (with daytime running light).
1.CHECK TAIL LAMP OPERATION EXL
CONSULT ACTIVE TEST
1. Select “DAYTIME RUNNING LIGHT” of BCM(HEADLAMP) active test item.
2. With operating the test items, check that the tail lamp is turned ON. M

ON : Tail Lamp ON
Off : Tail lamp OFF N
Is the inspection result normal?
YES >> Tail lamp circuit is normal.
NO >> Refer to EXL-231, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure". O

WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006756604

P
1.CHECK TAIL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK TAIL LAMP OPERATION
EXL-231
 TAIL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
Check that the tail lamp is turned ON.
Which tail lamp does not turn ON?
RH >> GO TO 3.
LH >> GO TO 4.
3.CHECK TAIL LAMP RH OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove tail lamp RH relay.
3. Disconnect rear combination lamp RH connector.
4. Check continuity between tail lamp RH relay harness connector and rear combination lamp RH harness
connector.

Tail lamp RH relay Rear combination lamp RH

Continuity
Connector Terminal Connector Terminal
E71 3 B59 6 Existed
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
4.CHECK TAIL LAMP LH OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove tail lamp LH relay.
3. Disconnect rear combination lamp LH connector.
4. Check continuity between tail lamp LH relay harness connector and rear combination lamp LH harness
connector.

Tail lamp LH relay Rear combination lamp LH

Continuity
Connector Terminal Connector Terminal
E67 3 B80 6 Existed
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
5.CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground.

Rear combination lamp

Continuity
Connector Terminal
Ground
RH B59
3 Existed
LH B80
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.

EXL-232
 LICENSE PLATE LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
LICENSE PLATE LAMP CIRCUIT
A
Component Function Check INFOID:0000000006756607

NOTE: B
Check tail lamp RH and LH relay circuit first if the parking lamp, the tail lamp, and the license plate lamp are
not turned ON.
• Tail lamp RH relay circuit: Refer to EXL-224, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis
Procedure" (without daytime running light), EXL-225, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag- C
nosis Procedure" (with daytime running light).
• Tail lamp LH relay circuit: Refer to EXL-220, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis
Procedure" (without daytime running light), EXL-221, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag- D
nosis Procedure" (with daytime running light).
1.CHECK LICENSE PLATE LAMP OPERATION
E
CONSULT ACTIVE TEST
1. Select “TAIL LAMP” or “DAYTIME RUNNING LIGHT” of BCM(HEADLAMP) active test item.
2. With operating the lighting switch, check that the license plate lamp is turned ON.
F
On : License plate lamp ON
Off : License plate lamp OFF
G
Is the inspection result normal?
YES >> License plate lamp circuit is normal.
NO >> Refer to EXL-233, "Diagnosis Procedure".
NOTE: H
For active test items of models with daytime running light, use “DAYTIME RUNNING LIGHT”.
Diagnosis Procedure INFOID:0000000006756608
I
1.CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb. J
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace bulb. K
2.CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
EXL
2. Remove tail lamp RH relay.
3. Disconnect license plate lamp connector.
4. Check continuity between tail lamp RH relay harness connector and license plate lamp harness connec-
tor. M

Tail lamp RH relay License plate lamp

Continuity
Connector Terminal Connector Terminal N
E71 3 B46 1 Existed
Is the inspection result normal?
O
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT P
Check continuity between license plate lamp harness connector and ground.

License plate lamp

Continuity
Connector Terminal Ground
B46 2 Existed
Is the inspection result normal?

EXL-233
 LICENSE PLATE LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.

EXL-234
 LIGHT & RAIN SENSOR
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
LIGHT & RAIN SENSOR
A
Component Function Check INFOID:0000000006756609

1.CHECK LIGHT & RAIN SENSOR B

1. Clean light & rain sensor detection area of windshield fully.
2. Turn ignition switch ON.
3. Turn lighting switch AUTO. C
4. With the light & rain sensor illuminating, check the auto light function.

Condition Auto light function

D
When illuminating Not operating
Light & rain sensor
When shutting off light Operating
Is the inspection result normal? E
YES >> Light & rain sensor is normal.
NO >> Refer to EXL-235, "Diagnosis Procedure".
F
Diagnosis Procedure INFOID:0000000006756610

1.CHECK LIGHT & RAIN SENSOR FUSE G

1. Turn ignition switch OFF.
2. Check that the following fuse is not fusing.
H
Unit Fuse No. Capacity
Light & rain sensor #13 10 A
Is the inspection result normal? I
YES >> GO TO 2.
NO >> Replace the fuse after repairing the applicable circuit.
2.CHECK LIGHT & RAIN SENSOR POWER SUPPLY J

1. Disconnect light & rain sensor connector.

2. Check voltage between light & rain sensor harness connector and ground.
K
(+)
Voltage
Light & rain sensor (−)
(Approx.) EXL
Connector Terminal
R12 1 Ground Battery voltage
Is the inspection result normal? M
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK LIGHT & RAIN SENSOR GROUND CIRCUIT N

Check continuity between light & rain sensor harness connector and ground.
O
Light & rain sensor
Continuity
Connector Terminal Ground
R12 3 Existed P
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK LIGHT & RAIN SENSOR SIGNAL
1. Connect light & rain sensor connector.
2. Turn ignition switch ON.

EXL-235
 LIGHT & RAIN SENSOR
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
3. Check signal between BCM harness connector and ground with oscilloscope.

(+)
Signal
BCM (−) Condition
(Reference value)
Connector Terminal

M65*1
14 Ground Ignition switch ON
M68*2

JPMIA0156GB

Approx. 8.7V
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> Replace light & rain sensor.
NO >> GO TO 5.
5.CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM connector and light & rain sensor connector.
3. Check continuity between BCM harness connector and light & rain sensor harness connector.

BCM Light & rain sensor

Continuity
Connector Terminal Connector Terminal

M65*1
14 R12 2 Existed
M68*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT FOR SHORT
Check continuity between BCM harness connector and ground.

BCM
Continuity
Connector Terminal
Ground
M65*1
14 Not existed
M68*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> Refer to BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
NO >> Repair or replace harness.

EXL-236
 FRONT FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
FRONT FOG LAMP CIRCUIT
A
Component Function Check INFOID:0000000006825093

1.CHECK FRONT FOG LAMP OPERATION B

CONSULT ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the front fog lamp is turned ON. C

Fog : Front fog lamp ON

Off : Front fog lamp OFF D
Is the inspection result normal?
YES >> Front fog lamp circuit is normal.
E
NO >> Refer to EXL-237, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006825094

F
1.CHECK FRONT FOG LAMP INPUT SIGNAL
CONSULT ACTIVE TEST
1. Turn ignition switch OFF. G
2. Disconnect front fog lamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item. H
5. With operating the test items, check voltage between front fog lamp harness connector and ground.

(+)
Voltage I
Front fog lamp (−) Test item
(Approx.)
Connector Terminal
Fog Battery voltage J
RH E48
Off 0V
1 Ground EXTERNAL LAMPS
Fog Battery voltage
LH E30 K
Off 0V
Is the inspection result normal?
YES >> GO TO 2. EXL
NO >> GO TO 3.
2.CHECK FRONT FOG LAMP GROUND CIRCUIT
1. Turn ignition switch OFF. M
2. Check continuity between front fog lamp harness connector and ground.

Front fog lamp N

Continuity
Connector Terminal
Ground
RH E48
2 Existed O
LH E30
Is the inspection result normal?
YES >> Replace bulb. P
NO >> Repair or replace harness.
3.CHECK FRONT FOG LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove front fog lamp relay.
3. Check continuity between front fog lamp relay harness connector and front fog lamp harness connector.

EXL-237
 FRONT FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]

Front fog lamp Front fog lamp relay

Continuity
Connector Terminal Connector Terminal
RH E48
1 E3 3 Existed
LH E30
Is the inspection result normal?
YES >> Refer to GI-51, "Intermittent Incident".
NO >> Repair or replace harness.

EXL-238
 FRONT FOG LAMP RELAY
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
FRONT FOG LAMP RELAY
A
Diagnosis Procedure INFOID:0000000006825095

1.CHECK FRONT FOG LAMP FUSE B

1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.
C
Unit Fuse No. Capacity
Front fog lamp #39 15 A
Is the inspection result normal? D
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
E
2.CHECK FRONT FOG LAMP RELAY POWER SUPPLY CIRCUIT
1. Remove front fog lamp relay.
2. Check voltage front fog lamp relay harness connector and ground. F

(+)
Voltage
Front fog lamp relay (–) G
(Approx.)
Connector Terminal
2
E3 Ground Battery voltage H
5
Is the inspection result normal?
YES >> GO TO 3. I
NO >> Repair or replace harness.
3.CHECK FRONT FOG LAMP RELAY CIRCUIT 1
CONSULT ACTIVE TEST J
1. Install front fog lamp relay.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item. K
4. With operating the test items, check voltage between IPDM E/R harness connector and ground.

(+)
Voltage
EXL
IPDM E/R (–) Test item
(Approx.)
Connector Terminal

EXTERNAL Fog 0V M
E10 21 Ground
LAMPS Off Battery voltage
Is the inspection result normal?
N
YES >> GO TO 5.
Fixed battery voltage>>Replace IPDM E/R.
Fixed 0 V>>GO TO 4.
O
4.CHECK FRONT FOG LAMP RELAY CIRCUIT 2
1. Remove front fog lamp relay.
2. Disconnect IPDM E/R connector. P
3. Check continuity between IPDM E/R harness connector and front fog lamp relay harness connector.

IPDM E/R Front fog lamp relay

Continuity
Connector Terminal Connector Terminal
E10 21 E3 1 Existed
4. Check continuity between IPDM E/R harness connector and ground.

EXL-239
 FRONT FOG LAMP RELAY
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]

IPDM E/R
Continuity
Connector Terminal Ground
E10 21 Not existed
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
5.CHECK FRONT FOG LAMP RELAY 1
1. Remove front fog lamp relay.
2. Check front fog lamp relay.
Refer to EXL-240, "Component Inspection"
Is the inspection result normal?
YES >> Front fog lamp relay circuit is normal.
NO >> Replace front fog lamp relay.
6.CHECK FRONT FOG LAMP RELAY 2
1. Remove front fog lamp relay.
2. Check front fog lamp relay.
Refer to EXL-240, "Component Inspection"
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Replace front fog lamp relay.
Component Inspection INFOID:0000000006825096

1.CHECK FRONT FOG LAMP RELAY

1. Turn ignition switch OFF.
2. Remove front fog lamp relay.
3. Check continuity between front fog lamp relay terminals.

Terminal
Condition Continuity
Front fog lamp relay
12 V direct current supply between termi-
Existed
3 5 nals 1 and 2
No current supply Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace front fog lamp relay.
SEF497Y

EXL-240
 REAR FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
REAR FOG LAMP CIRCUIT
A
Component Function Check INFOID:0000000006825109

1.CHECK REAR FOG LAMP OPERATION B

CONSULT ACTIVE TEST
1. Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item.
2. With operating the test items, check that the rear fog lamp is turned ON. C

On : Rear fog lamp ON

Off : Rear fog lamp OFF D
Is the inspection result normal?
YES >> Rear fog lamp circuit is normal.
E
NO >> Refer to EXL-241, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006825110

F
1.CHECK REAR FOG LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal? G
YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK REAR FOG LAMP OUTPUT VOLTAGE H

CONSULT ACTIVE TEST

1. Turn ignition switch OFF. I
2. Disconnect rear combination lamp connector.
3. Turn ignition switch ON.
4. Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item.
5. With operating the test items, check voltage between rear combination lamp harness connector and J
ground.
LHD models
(+) K
Voltage
Rear combination lamp LH (−) Test item
(Approx.)
Connector Terminal
EXL
On 12 V
B80 2 Ground RR FOG LAMP
Off 0V

RHD models M
(+)
Voltage
Rear combination lamp RH (−) Test item
(Approx.)
N
Connector Terminal
On 12 V
B59 2 Ground RR FOG LAMP
Off 0V O
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 3. P
3.CHECK REAR FOG LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and rear combination lamp harness connector.

EXL-241
 REAR FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
LHD models
BCM Rear combination lamp LH
Continuity
Connector Terminal Connector Terminal

M66*1
52 B80 2 Existed
M69*2
*1: Without Intelligent Key
*2: With Intelligent Key
RHD models
BCM Rear combination lamp RH
Continuity
Connector Terminal Connector Terminal

M66*1
52 B59 2 Existed
M69*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK REAR FOG LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.

BCM
Continuity
Connector Terminal
Ground
M66*1
52 Not existed
M69*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> Check bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer to
BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338, "Removal and Installation"
(without Intelligent Key).
NO >> Repair or replace harness.
5.CHECK REAR FOG LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
LHD models
Rear combination lamp LH
Continuity
Connector Terminal Ground
B80 3 Existed

RHD models
Rear combination lamp RH
Continuity
Connector Terminal Ground
B59 3 Existed
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.

EXL-242
 TURN SIGNAL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
TURN SIGNAL LAMP CIRCUIT
A
Component Function Check INFOID:0000000006825111

1.CHECK TURN SIGNAL LAMP B

CONSULT ACTIVE TEST
1. Select “FLASHER” of BCM (FLASHER) active test item.
2. With operating the test items, check that the turn signal lamps is turned ON. C

LH : Turn signal lamps (LH) ON

RH : Turn signal lamps (RH) ON D
Off : Turn signal lamps OFF
Is the inspection result normal? E
YES >> Turn signal lamp circuit is normal.
NO >> Refer to EXL-243, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006825112 F

1.CHECK TURN SIGNAL LAMP BULB

Check the applicable lamp bulb. G
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace bulb. H

2.CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

1. Turn ignition switch OFF. I
2. Disconnect front turn signal lamp connector, side turn signal lamp connector and rear combination lamp
connector.
3. Turn ignition switch ON.
J
4. With operating the turn signal switch, check voltage between BCM harness connector and ground.

(+)
BCM (–) Condition
Voltage K
(Approx.)
Connector Terminal

EXL

LH M
60

PKID0926E
N
M67*1 Turn signal OFF 0V
Ground
M70*2 switch
O

RH
61
P

PKID0926E

OFF 0V

*1: Without Intelligent Key

*2: With Intelligent Key

EXL-243
 TURN SIGNAL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4.
3.CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp harness connector.
Front turn signal lamp
BCM Front turn signal lamp
Continuity
Connector Terminal Connector Terminal
RH M67*1 61 E46
1 Existed
LH M70*2 60 E27

Side turn signal lamp

BCM Side turn signal lamp
Continuity
Connector Terminal Connector Terminal
RH M67*1 61 E40
*2
1 Existed
LH M70 60 E23

Rear turn signal lamp

BCM Rear combination lamp
Continuity
Connector Terminal Connector Terminal
RH M67*1 61 B59
*2
4 Existed
LH M70 60 B80

*1: Without Intelligent Key

*2: With Intelligent Key
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
4.CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.

BCM
Continuity
Connector Terminal
Ground
RH M67*1 61
Not existed
LH M70*2 60

*1: Without Intelligent Key

*2: With Intelligent Key
Is the inspection result normal?
YES >> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer
to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338, "Removal and Installa-
tion" (without Intelligent Key).
NO >> Repair or replace harness.
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp and ground.

EXL-244
 TURN SIGNAL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
Front turn signal lamp
Front turn signal lamp A
Continuity
Connector Terminal
Ground
RH E46
2 Existed B
LH E27

Side turn signal lamp

Side turn signal lamp
Continuity C
Connector Terminal
Ground
RH E40
2 Existed
LH E23 D
Rear turn signal lamp
Rear combination lamp
Continuity E
Connector Terminal
Ground
RH B59
3 Existed
LH B80 F
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness. G

EXL

EXL-245
 HAZARD SWITCH
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
HAZARD SWITCH
Component Function Check INFOID:0000000006825113

1.CHECK HAZARD SWITCH SIGNAL BY CONSULT

CONSULT DATA MONITOR
1. Turn the ignition switch ON.
2. Select “HAZARD SW” of BCM (FLASHER) data monitor item.
3. With operating the hazard switch, check the monitor status.

Monitor item Condition Monitor status

ON On
HAZARD SW Hazard switch
OFF Off
Is the inspection result normal?
YES >> Hazard switch circuit is normal.
NO >> Refer to EXL-246, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006825114

1.CHECK HAZARD SWITCH SIGNAL INPUT

1. Turn ignition switch OFF.
2. Disconnect hazard switch connector.
3. Check voltage between hazard switch connector and ground.

(+)
Hazard switch (−) Voltage (Approx.)
Connector Terminal
M45 2 Ground 12 V
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between hazard switch harness connector and BCM harness connector.

Hazard switch BCM

Continuity
Connector Terminal Connector Terminal

M65*1
M45 2 29 Existed
M68*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT
Check continuity between hazard switch harness connector and ground.

Hazard switch
Continuity
Connector Terminal Ground
M45 2 Not existed
Is the inspection result normal?

EXL-246
 HAZARD SWITCH
< DTC/CIRCUIT DIAGNOSIS > [TYPE 2]
YES >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key) or BCS-338,
"Removal and Installation" (without Intelligent Key). A
NO >> Repair or replace harness.
4.CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
B
Check continuity between hazard switch harness connector and ground.

Hazard switch
Continuity C
Connector Terminal Ground
M45 1 Existed
Is the inspection result normal? D
YES >> Replace hazard switch.
NO >> Repair or replace harness.
E

EXL

EXL-247
 EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [TYPE 2]

SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Symptom Table INFOID:0000000006756615

CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.

Symptom Possible cause Inspection item

• Fuse
• Halogen bulb
• Harness between IPDM E/R and Headlamp (HI) circuit
One side headlamp Refer to EXL-214, "Component
Headlamp (HI) is not • Harness between headlamp and Function Check".
turned ON. ground
• IPDM E/R
Symptom diagnosis
Both sides “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to EXL-252, "Diagnosis Procedure".
• Combination meter
High beam indicator lamp is not turned ON. Data monitor “HI-BEAM IND”
Combination meter
[Headlamp (HI) is turned ON.] • BCM (HEADLAMP)
Active test “HEADLAMP”
• Fuse
• Halogen bulb
• Harness between IPDM E/R and Headlamp (LO) circuit
Headlamp (LO) is not One side headlamp Refer to EXL-216, "Component
turned ON. • Harness between headlamp and Function Check".
ground
• IPDM E/R
Both sides Symptom diagnosis
When ignition switch “BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
is turned ON. Refer to EXL-253, "Diagnosis Procedure".
Headlamp is not turned
OFF. When ignition switch
IPDM E/R —
is turned OFF.
• Harness between headlamp and Headlamp ground circuit
Headlamp HI and LO are not turned ON. ground Refer to EXL-218, "Diagnosis Pro-
• Halogen bulb cedure".
• Combination switch
Combination switch
• Harness between combination
Refer to BCS-196, "Symptom Ta-
switch and BCM
ble".
Each lamp is not turned ON/OFF with lighting • BCM
switch AUTO. • Light & rain sensor
Light & rain sensor
• Harness between light & rain sen-
Refer to EXL-235, "Component
sor and BCM
Function Check".
• BCM
• Parking lamp bulb
Parking lamp circuit
• Harness between IPDM E/R and
Parking lamp is not turned ON. Refer to EXL-228, "Component
parking lamp
Function Check".
• IPDM E/R
• Tail lamp bulb Tail lamp circuit
• Harness between IPDM E/R and Refer to EXL-230, "WITHOUT DAY-
Tail lamp is not turned ON.
rear combination lamp TIME RUNNING LIGHT SYSTEM :
• IPDM E/R Component Function Check".

EXL-248
 EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [TYPE 2]
Symptom Possible cause Inspection item
A
• License plate lamp bulb License plate lamp circuit
License plate lamp is not turned ON. • Harness between IPDM E/R and Refer to EXL-233, "Component
license plate lamp Function Check".
• Fuse B
Tail lamp RH relay circuit
• Harness between IPDM E/R and
Parking lamp, tail lamp RH and license plate lamp Refer to EXL-224, "WITHOUT DAY-
tail lamp RH relay
are not turned ON. TIME RUNNING LIGHT SYSTEM :
• IPDM E/R
• Tail lamp RH relay
Diagnosis Procedure". C
• Parking lamp, tail lamp and license plate lamp Symptom diagnosis
are not turned ON. “PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
• Parking lamp, tail lamp and license plate lamp Refer to EXL-254, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Di- D
are not turned OFF. agnosis Procedure".
Indicator lamp is nor-
mal. • Harness between BCM and each Turn signal lamp circuit E
(Applicable side per- turn signal lamp Refer to EXL-243, "Component
forms the high flasher • Turn signal lamp bulb Function Check".
Turn signal lamp does activation.)
not blink. F
• Combination switch
Combination switch
Indicator lamp is in- • Harness between combination
Refer to BCS-196, "Symptom Ta-
cluded. switch and BCM
ble".
• BCM G
One side Combination meter —
• Combination meter
• Turn signal indicator lamp signal
Both sides
- BCM
Data monitor “TURN IND” H
Turn signal indicator (Always) • BCM (FLASHER)
• Combination meter
lamp does not blink. Active test “FLASHER”
(Turn signal indicator
Both sides
lamp is normal.) Combination meter I
(Only when activating • Combination meter power supply
Power supply and ground circuit
hazard warning lamp and ground circuit
Refer to MWI-123, "COMBINATION
with the ignition switch • Combination meter
METER : Diagnosis Procedure".
OFF.) J
• Hazard switch
• Hazard warning lamp does not activate. Hazard switch
• Harness between hazard switch
• Hazard warning lamp continues activating. Refer to EXL-246, "Component
and BCM
(Turn signal is normal.)
• BCM
Function Check". K

• Front fog lamp bulb Front fog lamp circuit

Front fog lamp is not One side • Harness between front fog lamp Refer to EXL-237, "Component
turned ON. relay and front fog lamp Function Check". EXL
Both side Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Front fog lamp is not turned OFF. Refer to EXL-256, "Diagnosis Procedure". M
• Combination meter
Front fog lamp indicator is not turned ON. Data monitor “FR FOG IND”
Combination meter
(Front fog lamp is turned ON.) • BCM (HEAD LAMP)
N
Active test “FR FOG LAMP”
• Harness between BCM and rear
Rear fog lamp circuit
Rear fog lamp indica- fog lamp
Refer to EXL-241, "Component O
tor lamp is normal. • Rear fog lamp bulb
Function Check".
Rear fog lamp is not • BCM
turned ON. • Combination switch
Combination switch
Rear fog lamp indica- • Harness between combination P
Refer to BCS-196, "Symptom Ta-
tor lamp is included. switch and BCM
ble".
• BCM
• Combination meter
• Rear fog lamp status signal
Rear fog lamp indicator lamp is not turn ON. Data monitor “RR FOG IND”
• Combination meter
(Rear fog lamp turns ON) • BCM (HEAD LAMP)
• BCM
Active test “RR FOG LAMP”

WITH DAYTIME RUNNING LIGHT SYSTEM

EXL-249
 EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [TYPE 2]
WITH DAYTIME RUNNING LIGHT SYSTEM : Symptom Table INFOID:0000000006827042

CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.

Symptom Possible cause Inspection item

• Fuse
• Halogen bulb
• Harness between IPDM E/R and Headlamp (HI) circuit
One side headlamp Refer to EXL-214, "Component
Headlamp (HI) is not • Harness between headlamp and Function Check".
turned ON. ground
• IPDM E/R
Symptom diagnosis
Both sides “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to EXL-252, "Diagnosis Procedure".
• Combination meter
High beam indicator lamp is not turned ON. Data monitor “HI-BEAM IND”
Combination meter
[Headlamp (HI) is turned ON.] • BCM (HEADLAMP)
Active test “HEADLAMP”
• Fuse
• Halogen bulb
• Harness between IPDM E/R and Headlamp (LO) circuit
Headlamp (LO) is not One side headlamp Refer to EXL-216, "Component
turned ON. • Harness between headlamp and Function Check".
ground
• IPDM E/R
Both sides Symptom diagnosis
When ignition switch “BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
is turned ON. Refer to EXL-253, "Diagnosis Procedure".
Headlamp is not turned
OFF. When ignition switch
IPDM E/R —
is turned OFF.
• Harness between headlamp and Headlamp ground circuit
Headlamp HI and LO are not turned ON. ground Refer to EXL-218, "Diagnosis Pro-
• Halogen bulb cedure".
• Combination switch
Combination switch
• Harness between combination
Refer to BCS-196, "Symptom Ta-
switch and BCM
ble".
Each lamp is not turned ON/OFF with lighting • BCM
switch AUTO. • Light & rain sensor
Light & rain sensor
• Harness between light & rain sen-
Refer to EXL-235, "Component
sor and BCM
Function Check".
• BCM
• Parking lamp bulb
Parking lamp circuit
• Harness between IPDM E/R and
Parking lamp is not turned ON. Refer to EXL-228, "Component
parking lamp
Function Check".
• IPDM E/R
• Tail lamp bulb Tail lamp circuit
• Harness between IPDM E/R and Refer to EXL-231, "WITH DAYTIME
Tail lamp is not turned ON.
rear combination lamp RUNNING LIGHT SYSTEM : Com-
• IPDM E/R ponent Function Check".
• License plate lamp bulb License plate lamp circuit
License plate lamp is not turned ON. • Harness between IPDM E/R and Refer to EXL-233, "Component
license plate lamp Function Check".

EXL-250
 EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [TYPE 2]
Symptom Possible cause Inspection item
A
• Fuse
Tail lamp RH relay circuit
• Harness between IPDM E/R and
Parking lamp, tail lamp RH and license plate lamp Refer to EXL-227, "WITH DAYTIME
tail lamp RH relay
are not turned ON. RUNNING LIGHT SYSTEM : Com-
• IPDM E/R B
ponent Inspection".
• Tail lamp RH relay
• Parking lamp, tail lamp and license plate lamp
Symptom diagnosis
are not turned ON.
• Parking lamp, tail lamp and license plate lamp
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON” C
Refer to EXL-254, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagno-
are not turned OFF.
sis Procedure".
(Each illumination is turned ON/OFF.)
Indicator lamp is nor- D
mal. • Harness between BCM and each Turn signal lamp circuit
(Applicable side per- turn signal lamp Refer to EXL-243, "Component
forms the high flasher • Turn signal lamp bulb Function Check".
Turn signal lamp does activation.) E
not blink.
• Combination switch
Combination switch
Indicator lamp is in- • Harness between combination
Refer to BCS-196, "Symptom Ta-
cluded. switch and BCM
ble".
F
• BCM
One side Combination meter —
• Combination meter G
• Turn signal indicator lamp signal
Both sides Data monitor “TURN IND”
- BCM
Turn signal indicator (Always) • BCM (FLASHER)
• Combination meter
lamp does not blink. Active test “FLASHER”
(Turn signal indicator
H
Both sides
lamp is normal.) Combination meter
(Only when activating • Combination meter power supply
Power supply and ground circuit
hazard warning lamp and ground circuit
Refer to MWI-123, "COMBINATION
with the ignition switch • Combination meter I
METER : Diagnosis Procedure".
OFF.)
• Hazard switch
• Hazard warning lamp does not activate. Hazard switch
• Harness between hazard switch J
• Hazard warning lamp continues activating. Refer to EXL-246, "Component
and BCM
(Turn signal is normal.) Function Check".
• BCM
• Front fog lamp bulb Front fog lamp circuit
One side • Harness between front fog lamp Refer to EXL-237, "Component
K
Front fog lamp is not
turned ON. relay and front fog lamp Function Check".
Both side Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON” EXL
Front fog lamp is not turned OFF. Refer to EXL-256, "Diagnosis Procedure".
• Combination meter
Front fog lamp indicator is not turned ON. Data monitor “FR FOG IND” M
Combination meter
(Front fog lamp is turned ON.) • BCM (HEAD LAMP)
Active test “FR FOG LAMP”
• Harness between BCM and rear
Rear fog lamp circuit N
Rear fog lamp indica- fog lamp
Refer to EXL-241, "Component
tor lamp is normal. • Rear fog lamp bulb
Function Check".
Rear fog lamp is not • BCM
turned ON. • Combination switch O
Combination switch
Rear fog lamp indica- • Harness between combination
Refer to BCS-196, "Symptom Ta-
tor lamp is included. switch and BCM
ble".
• BCM
P
• Combination meter
• Rear fog lamp status signal
Rear fog lamp indicator lamp is not turn ON. Data monitor “RR FOG IND”
• Combination meter
(Rear fog lamp turns ON) • BCM (HEAD LAMP)
• BCM
Active test “RR FOG LAMP”

EXL-251
 BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [TYPE 2]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
Description INFOID:0000000006765912

Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis Procedure INFOID:0000000006765913

1.COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to BCS-196, "Symptom Table".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “HL HI REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.

Monitor item Condition Monitor status

Lighting switch HI or PASS ON

HL HI REQ
(2ND) LO OFF
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
3.HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to EXL-214, "Component Function Check".
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.

EXL-252
 BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [TYPE 2]
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
A
Description INFOID:0000000006765914

Both side headlamps (LO) are not turned ON in any condition. B

Diagnosis Procedure INFOID:0000000006765915

1.CHECK COMBINATION SWITCH C

Check the combination switch. Refer to BCS-196, "Symptom Table".
Is the inspection result normal?
D
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT E
CONSULT DATA MONITOR
1. Select “HL LO REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status. F

Monitor item Condition Monitor status

2ND ON G
HL LO REQ Lighting switch
OFF OFF
Is the inspection result normal? H
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
I
3.HEADLAMP (LO) CIRCUIT INSPECTION
Check the headlamp (LO) circuit. Refer to EXL-216, "Component Function Check".
Is the inspection result normal? J
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
K

EXL

EXL-253
 PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [TYPE 2]
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Description INFOID:0000000006765920

The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006765921

1.COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to BCS-196, "Symptom Table".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.

Monitor item Condition Monitor status

1ST ON
TAIL & CLR REQ Lighting switch
OFF OFF
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
3.TAIL LAMP RH RELAY CIRCUIT INSPECTION
Check the tail lamp RH relay circuit. Refer to EXL-224, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM :
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning part.
4.TAIL LAMP LH RELAY CIRCUIT INSPECTION
Check the tail lamp LH relay circuit. Refer to EXL-220, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM :
Diagnosis Procedure".
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Description INFOID:0000000006827053

The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006827054

1.COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to BCS-196, "Symptom Table".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
EXL-254
 PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [TYPE 2]
CONSULT DATA MONITOR
1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item. A
2. With operating the lighting switch, check the monitor status.

Monitor item Condition Monitor status B

1ST ON
TAIL & CLR REQ Lighting switch
OFF OFF
C
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338, D
"Removal and Installation" (without Intelligent Key).
3.TAIL LAMP RH RELAY CIRCUIT INSPECTION
Check the tail lamp RH relay circuit. Refer to EXL-221, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag- E
nosis Procedure".
Is the inspection result normal?
YES >> GO TO 4. F
NO >> Repair or replace the malfunctioning part.
4.TAIL LAMP LH RELAY CIRCUIT INSPECTION
G
Check the tail lamp LH relay circuit. Refer to EXL-225, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagno-
sis Procedure".
Is the inspection result normal?
H
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.
I

EXL

EXL-255
 BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [TYPE 2]
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description INFOID:0000000006765918

The front fog lamps are not turned ON in any condition.

Diagnosis Procedure INFOID:0000000006765919

1.CHECK FUSE
Check that the following fuse is fusing.

Unit Fuse No. Capacity

Front fog lamp #39 15 A
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the applicable circuit. And then replace the fuse.
2.COMBINATION SWITCH INSPECTION
Check combination switch. Refer to BCS-196, "Symptom Table".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning part.
3.CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “FR FOG REQ” of IPDM E/R data monitor item.
2. With operating the front fog lamp switch, check the monitor status.

Monitor item Condition Monitor status

Front fog lamp switch ON ON

FR FOG REQ
(With lighting switch 1ST) OFF OFF
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with Intelligent Key), BCS-338,
"Removal and Installation" (without Intelligent Key).
4.FRONT FOG LAMP RELAY CIRCUIT INSPECTION
Check front fog lamp relay circuit. Refer to EXL-239, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning part.
5.FRONT FOG LAMP CIRCUIT INSPECTION
Check front fog lamp circuit. Refer to EXL-237, "Component Function Check".
Is the inspection result normal?
YES >> Replace IPDM E/R.
NO >> Repair or replace the malfunctioning part.

EXL-256
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 2]

PERIODIC MAINTENANCE A
HEADLAMP AIMING ADJUSTMENT
LHD
B
LHD : Description INFOID:0000000006891837

PREPARATION BEFORE ADJUSTING C

NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been D
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification. E
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE: F
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION: G
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW H

EXL

JMLIA1020ZZ P

A. Headlamp RH (UP/DOWN) B. Headlamp RH (INSIDE/OUTSIDE) C. Headlamp LH (INSIDE/OUTSIDE)

adjustment screw adjustment screw adjustment screw
D. Headlamp LH (UP/DOWN)
adjustment screw
: Vehicle center

EXL-257
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 2]

Adjustment screw Screw driver rotation Facing direction

Clockwise UP
A Headlamp RH (UP/DOWN)
Counterclockwise DOWN
Clockwise INSIDE
B Headlamp RH (INSIDE/OUTSIDE)
Counterclockwise OUTSIDE
Clockwise INSIDE
C Headlamp LH (INSIDE/OUTSIDE)
Counterclockwise OUTSIDE
Clockwise UP
D Headlamp LH (UP/DOWN)
Counterclockwise DOWN

LHD : Aiming Adjustment Procedure INFOID:0000000006891838

1. Place the screen.

NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
• Set the screen so that it is perpendicular to a level load surface.
2. Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3. Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:
Do not cover lens surface with tape, etc. because it is made from plastic.
4. Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
Low beam distribution on the screen

JSLIA0030ZZ

A. Aiming adjustment area

B. Elbow point
C. Headlamp center
H. Horizontal center line of headlamp
V. Vertical center line of headlamp

EXL-258
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 2]

JSLIA0031ZZ F

C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
G
(lateral) (Vertical)

Distance from headlamp center to screen (L) : 10 m (32.8 ft) H

Unit: mm (in)
Aiming adjustment area
Vertical direction (Y) Lateral direction (X) I
(Lower side from headlamp center height) (Right side from headlamp center line)
Highest light axis 100 3.94)
Target light axis 100 (3.94) 0 -100 (3.94) J
Lowest light axis 150 (5.91)

RHD K

RHD : Description INFOID:0000000006891839

EXL
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been M
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification. N
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.) O
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
P
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW

EXL-259
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 2]

JMLIA1020ZZ

A. Headlamp RH (UP/DOWN) B. Headlamp RH (INSIDE/OUTSIDE) C. Headlamp LH (INSIDE/OUTSIDE)

adjustment screw adjustment screw adjustment screw
D. Headlamp LH (UP/DOWN)
adjustment screw
: Vehicle center

Adjustment screw Screw driver rotation Facing direction

Clockwise UP
A Headlamp RH (UP/DOWN)
Counterclockwise DOWN
Clockwise INSIDE
B Headlamp RH (INSIDE/OUTSIDE)
Counterclockwise OUTSIDE
Clockwise INSIDE
C Headlamp LH (INSIDE/OUTSIDE)
Counterclockwise OUTSIDE
Clockwise UP
D Headlamp LH (UP/DOWN)
Counterclockwise DOWN

RHD : Aiming Adjustment Procedure INFOID:0000000006891840

1. Place the screen.

NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
• Set the screen so that it is perpendicular to a level load surface.
2. Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3. Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:

EXL-260
 HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 2]
Do not cover lens surface with tape, etc. because it is made from plastic.
4. Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so A
that it is within the aiming adjustment area.
Low beam distribution on the screen
B

JSLIA0028ZZ
E
A. Aiming adjustment area
B. Elbow point
C. Headlamp center F
H. Horizontal center line of headlamp
V. Vertical center line of headlamp
G

JSLIA0029ZZ
EXL
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
(lateral) (Vertical) M

Distance from headlamp center to screen (L) : 10 m (32.8 ft)

N
Unit: mm (in)
Aiming adjustment area
Vertical direction (Y) Lateral direction (X)
(Lower side from headlamp center height) (Left side from headlamp center line)
O

Highest light axis 100 (3.94)

Target light axis 100 (3.94) 0 -100 (3.94)
P
Lowest light axis 150 (5.91)

EXL-261
 FRONT FOG LAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 2]
FRONT FOG LAMP AIMING ADJUSTMENT
Description INFOID:0000000006891842

PREPARATION BEFORE ADJUSTING

NOTE:
• For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.

A: UP
B: DOWN
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.

JMLIA1040ZZ

Aiming Adjustment Procedure INFOID:0000000006891843

1. Place the screen.

NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2. Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3. Start the engine. Illuminate the front fog lamp.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4. Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen

JPLIA0008ZZ

EXL-262
 FRONT FOG LAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [TYPE 2]

A : Cutoff line A
B : High illuminance area
H : Horizontal center line of front fog lamp
V : Vertical center line of front fog lamp B
X : Cutoff line height

EXL

EXL-263
 FRONT COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]

REMOVAL AND INSTALLATION

FRONT COMBINATION LAMP
Exploded View INFOID:0000000006824431

REMOVAL

JMLIA1031ZZ

1. Front combination lamp

DISASSEMBLY

EXL-264
 FRONT COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]

H
JMLIA1032ZZ

1. Halogen bulb 2. Back cover 3. Parking lamp bulb socket

4. Parking lamp bulb 5. Retaining spring 6. Front turn signal lamp bulb socket I
7. Front turn signal lamp bulb 8. Headlamp housing assembly

Removal and Installation INFOID:0000000006824432 J

REMOVAL
CAUTION: K
Disconnect the battery negative terminal or the fuse.
1. Remove front bumper fascia. Refer to EXT-14, "Removal and Installation".
2. Remove the headlamp mounting bolts. EXL
3. Pull out the headlamp assembly forward the vehicle.
4. Disconnect the connectors, and then remove headlamp assembly.
M
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-113, "LHD : Description". N

Replacement INFOID:0000000006824433

CAUTION: O
• Disconnect the battery negative terminal or the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it. P
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1. Disconnect the headlamp bulb connector.
2. Remove the back cover.

EXL-265
 FRONT COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
3. Remove the retaining spring lock. And remove the bulb from the headlamp housing assembly.
PARKING LAMP BULB
1. Rotate the bulb socket counterclockwise and unlock it.
2. Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1. Rotate the bulb socket counterclockwise and unlock it.
2. Remove the bulb from the bulb socket.
Disassembly and Assembly INFOID:0000000006824434

DISASSEMBLY
1. Remove the back cover.
2. Remove the retaining spring lock, and then remove the bulb from the headlamp housing assembly.
3. Rotate the parking lamp bulb socket counterclockwise and unlock it.
4. Remove the bulb from the parking lamp bulb socket.
5. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
6. Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.

EXL-266
 FRONT FOG LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
FRONT FOG LAMP
A
Exploded View INFOID:0000000006824436

JMLIA1033ZZ

1. Front fog lamp bulb 2. Front fog lamp 3. Front fog lamp bracket G
4. Front bumper

Removal and Installation INFOID:0000000006824437 H

CAUTION:
Disconnect the battery negative terminal or the fuse.
I
REMOVAL
1. Remove the fender protector. Refer to EXT-21, "FENDER PROTECTOR : Removal and Installation".
2. Remove the front fog lamp connector. J
3. Remove the fixing screws, and then remove front fog lamp.
INSTALLATION K
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-118, "Description".
EXL
Replacement INFOID:0000000006824438

CAUTION: M
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect N
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
O
1. Remove the fender protector. Keep the service area.Refer to EXT-21, "FENDER PROTECTOR : Removal
and Installation".

EXL-267
 FRONT FOG LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
2. Remove the front fog lamp bulb connector (1).
3. Rotate the bulb (2) counterclockwise and unlock it.

SKIB8304J

EXL-268
 LIGHT & RAIN SENSOR
< REMOVAL AND INSTALLATION > [TYPE 2]
LIGHT & RAIN SENSOR
A
Exploded View INFOID:0000000006826828

CAUTION: B
When the light & rain sensor is removed from windshield, the light & rain sensor cannot be re-used.
REMOVAL
C

H
JMLIA1389ZZ

1. Light & rain sensor bracket 2. Mirror base 3. Light & rain sensor
I
4. Inside mirror assembly
: Pawl
Refer to GI-4, "Components" for symbols in the figure. J
Removal and Installation INFOID:0000000006826829

K
REMOVAL
1. Remove inside mirror assembly. Refer to MIR-78, "Removal and Installation".
2. Disconnect light & rain sensor connector. EXL
3. Disengage both sides of metal spring clips, and remove the light & rain sensor from the windshield.
INSTALLATION
Note the following items, and the install in the reverse order of removal. M
CAUTION:
• Surface of windshield should be cleaned.
• Never touch gel/adhesive of new part. N
• Lock the metal spring clips and install the light & rain sensor securely.

EXL-269
 LIGHTING & TURN SIGNAL SWITCH
< REMOVAL AND INSTALLATION > [TYPE 2]
LIGHTING & TURN SIGNAL SWITCH
Exploded View INFOID:0000000006824439

The lighting & turn switch is integrated in the combination switch. Refer to BCS-199, "Removal and Installa-
tion".

EXL-270
 SIDE TURN SIGNAL LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
SIDE TURN SIGNAL LAMP
A
Exploded View INFOID:0000000006824440

JPLIA1809ZZ

1. Side turn signal lamp bulb socket 2. Side turn signal lamp bulb 3. Side turn signal lamp housing G

Removal and Installation INFOID:0000000006824441

H
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL I
1. Remove the side turn signal lamp in numerical order shown in the figure.

: Vehicle front J
2. Rotate the bulb socket counterclockwise and unlock it.
NOTE:
Support side turn signal lamp harness with tape so that it won't K
fall into the front fender.

EXL

JMLIA1302ZZ
M
INSTALLATION
1. Rotate the bulb socket clockwise and lock it.
2. Fix the pawl-side behind the side turn signal lamp housing first, then push the resin clip-side. N
Replacement INFOID:0000000006824442

CAUTION: O
• Disconnect battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off. P
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
SIDE TURN SIGNAL LAMP BULB
1. Remove the side turn signal lamp.
2. Rotate the bulb socket counterclockwise and unlock it.
NOTE:

EXL-271
 SIDE TURN SIGNAL LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
Support the vehicle-side harness of the side turn signal lamp with tape so that it does not drop inside the
front fender.
3. Remove the bulb from the bulb socket.

EXL-272
 HAZARD SWITCH
< REMOVAL AND INSTALLATION > [TYPE 2]
HAZARD SWITCH
A
Exploded View INFOID:0000000006824443

JMLIA1042ZZ

1. Cluster lid C 2. Hazard switch G

Pawl

Removal and Installation INFOID:0000000006824444

H

REMOVAL
I
1. Remove the cluster lid C. Refer to IP-14, "Exploded View".
2. While pressing pawls, push the hazard switch to remove it.
INSTALLATION J
Install in the reverse order of removal.

EXL

EXL-273
 REAR COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
REAR COMBINATION LAMP
Exploded View INFOID:0000000006824445

REMOVAL

JMLIA1034ZZ

1. Grommet 2. Rear combination lamp

DISASSEMBLY

JMLIA1632ZZ

1. Stop/tail lamp bulb 2. Rear turn signal lamp bulb 3. Back-up lamp bulb (LDH models)/
Rear fog lamp bulb (RHD models)
4. Bulb holder 5. Seal packing RH 6. Back-up lamp bulb (RDH models)/
Rear fog lamp bulb (LHD models)
7. Seal packing LH
Refer to GI-4, "Components" for symbols in the figure.

Removal and Installation INFOID:0000000006824446

CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Wrap the tip of remover tool with a cloth to protect the body from damage.
REMOVAL
1. Remove rear combination lamp mounting bolts.
2. Pull rear combination lamp toward rear of the vehicle.

EXL-274
 REAR COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
3. Disconnect rear combination lamp connector, and then remove rear combination lamp.
A
INSTALLATION
Install in the reverse order of removal.
Replacement INFOID:0000000006824447 B

CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it. C
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one. D
STOP/TAIL LAMP BULB
1. Remove rear combination lamp assembly.
E
2. Disengage fixing pawls, and then remove bulb holder.

H
JMLIA1041ZZ

3. Rotate stop/tail lamp bulb counterclockwise, and then remove stop/tail lamp bulb. I
REAR TURN SIGNAL LAMP BULB
1. Remove rear combination lamp assembly.
J
2. Disengage fixing pawls, and then remove bulb holder.

EXL

M
JMLIA1041ZZ

3. Rotate rear turn signal lamp bulb counterclockwise, and then remove rear turn signal lamp bulb.
N
BACK-UP LAMP BULB
1. Remove rear combination lamp assembly.
2. Disengage fixing pawls, and then remove bulb holder. O

JMLIA1041ZZ

EXL-275
 REAR COMBINATION LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]

3. Rotate back-up lamp bulb counterclockwise, and then remove back-up lamp bulb.
REAR FOG LAMP BULB
1. Remove rear combination lamp assembly.
2. Disengage fixing pawls, and then remove bulb holder.

JMLIA1041ZZ

3. Rotate rear fog lamp bulb counterclockwise, and then remove rear fog lamp bulb.

EXL-276
 HIGH-MOUNTED STOP LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
HIGH-MOUNTED STOP LAMP
A
WITHOUT REAR SPOILER
WITHOUT REAR SPOILER : Exploded View INFOID:0000000006824448
B

JMLIA1036ZZ

H
1. Back door 2. Grommet 3. High-mounted stop lamp socket
4. High-mounted stop lamp bulb 5. Seal packing 6. High-mounted stop lamp
Refer to GI-4, "Components" for symbols in the figure.
I
WITHOUT REAR SPOILER : Removal and Installation INFOID:0000000006824449

CAUTION: J
Disconnect battery negative terminal or remove the fuse.
REMOVAL
K
1. Disengage high-mounted stop lamp fixing pawls with remover
tool (A).

: Metal clip EXL

CAUTION:
• Apply protect tape (B) on back door to protect the painted
surface from damage. M

N
JMLIA1021ZZ

• Never insert remover tool in the back door glass side to

O
prevent damage of back door glass.

JMLIA1022ZZ

EXL-277
 HIGH-MOUNTED STOP LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
2. Pull the high-mounted stop lamp toward rear of the vehicle.
3. Disconnect the high-mounted stop lamp harness connector, and then remove high-mounted stop lamp.
INSTALLATION
Install in the reverse order of removal.
WITHOUT REAR SPOILER : Replacement INFOID:0000000006824450

CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HIGH-MOUNTED STOP LAMP BULB
1. Remove the high-mounted stop lamp.
2. Rotate the bulb socket counterclockwise, and unlock it.
3. Remove the bulb from the bulb socket.
WITH REAR SPOILER
WITH REAR SPOILER : Exploded View INFOID:0000000006824451

High-mounted stop lamp is integrated in the rear spoiler. Refer to EXT-29, "Exploded View".
WITH REAR SPOILER : Removal and Installation INFOID:0000000006824452

REMOVAL
1. Remove rear spoiler. Refer to EXT-30, "Removal and Installation".
2. Remove high-mounted stop lamp cover fixing screws, and then remove high-mounted stop lamp cover.
3. Remove high-mounted stop lamp from rear spoiler.
INSTALLATION
Install in the reverse order of removal.

EXL-278
 LICENSE PLATE LAMP
< REMOVAL AND INSTALLATION > [TYPE 2]
LICENSE PLATE LAMP
A
Exploded View INFOID:0000000006824453

G
JMLIA1037ZZ

1. License plate lamp connector 2. License plate lamp bulb 3. License plate lamp housing
H
Removal and Installation INFOID:0000000006824454

CAUTION: I
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. While pressing the license plate lamp fixing pawl to direction right side, pull it to direction lower side and J
then remove it.
2. Rotate the bulb socket counterclockwise, and then remove bulb socket.
3. Remove the license plate lamp. K

INSTALLATION
Install in the reverse order of removal.
EXL
Replacement INFOID:0000000006824455

CAUTION: M
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect N
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
O
1. Remove the license plate lamp.
2. Remove the bulb from the socket.
P

EXL-279
 HEADLAMP AIMING SWITCH
< REMOVAL AND INSTALLATION > [TYPE 2]
HEADLAMP AIMING SWITCH
Exploded View INFOID:0000000006824456

For LHD models

JMLIA1147ZZ

1. Instrument lower panel assembly LH 2. Headlamp aiming switch 3. Switch panel

: Pawl

For RHD models

JMLIA1141ZZ

1. Instrument lower panel assembly RH 2. Headlamp aiming switch 3. Switch panel

: Pawl

Removal and Installation INFOID:0000000006824457

REMOVAL
1. Remove the switch panel with remover tool (A).
CAUTION:
Apply protective tape (B) on the part to protect from damage

2. Disengage the headlamp aiming switch harness connector and mirror control switch harness connector (if
so equipped).
3. Remove the headlamp aiming switch from switch panel.
INSTALLATION
Install in the reverse order of removal.

EXL-280
 SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS) [TYPE 2]

SERVICE DATA AND SPECIFICATIONS (SDS) A

SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications INFOID:0000000006824458
B

Item Type Wattage (W)

C
Headlamp (HI/LO) H4 60/55
Front combination lamp Front turn signal lamp PY21W (Amber) 21
Parking lamp W5W 5 D
Front fog lamp H11 55
Side turn signal lamp WY5W (Amber) 5
E
Stop lamp/Tail lamp P21W 21/5
Rear turn signal lamp PY21W (Amber) 21
Rear combination lamp
Back-up lamp P21W 21 F
Rear fog lamp P21W 21
License plate lamp W5W 5
High-mounted stop lamp W16W 18 G

EXL

EXL-281