Angular contact

ball bearings

Nomenclature
7200 BE CB Y HC5

2 4
1 3

1. Design: 2. Clearance: 3. Cage designs:

B 40° contact angle (C0)* Normal clearance (3000 series) Y Pressed brass cage,
ball guided
BE 40° contact angle, C2 Axial clearance tighter than
high capacity, normal (3000 and QJ series) M Machined brass cage,
all ISO corners rolling element guided
C3 Axial clearance looser than
A Conrad assembly (3000 series) normal (3000 and QJ series) MA Machined window-type brass
cage, outer ring centered
E Max type (3000 series)
P Injection molded cage
D Split inner ring (3300 series) 7000 series clearance of fiberglass reinforced
polyamide 6.6, rolling
NR Snap ring (3000 series) CA Modified for duplex mounting element guided
with axial clearance < normal
N2 Locating slot (QJ series) PHAS Injection molded window-type
CB Modified for duplex mounting cage of fiberglass reinforced
with normal axial clearance
2Z Shield on both sides polyetheretherketone (PEEK),
(3000 series) with lubrication grooves in the
CC Modified for duplex mounting guiding surfaces, outer ring center
with axial clearance > normal
2RS1 Seals of synthetic rubber (NBR)
on both sides (3000 series) J Pressed steel cage,
GA Modified for duplex mounting rolling element guided
with light preload
F Machined steel cage,
GB Modified for duplex mounting rolling element guided
with medium preload

GC Modified for duplex mounting 4. Special features:

with heavy preload
HC4 Full ceramic bearing
G.. Special preload, value in daN
HC5 Ceramic ball set
Note: 3000 series are double row
angular contact bearings * Not marked on bearing or package.

49
 Angular contact ball bearings

Technical
Product features
Details

Single row ACBB Double row ACBB Four-point contact ACBB

Boundary In accordance with In accordance with In accordance with

dimensions ISO 15-1998 ISO 15-1998 ISO 15-1998

Tolerances ABEC 3 (P6) ABEC 3 ABEC 1

Heat stabilization 257° F 257° F 257° F

(125° C) (125° C) (125° C)

Misalignment None – contact SKF None – contact SKF None – contact SKF

Cage materials Polyamide (P) Polyamide (TN9) Machined brass (M, MA)
Machined brass (M) (limited sizes only)
Pressed steel (J) Pressed steel (H)

Axial load – max 1.4 x C0 for 0.7 x C0 – Conrad 0.7 x C0

single or tandem Fa / Fr ≤ 0.3
mounted bearings
0.7 x C0 for duplex
mounted bearings

Seals Not available 2RS1 – Synthetic rubber (NBR) Not available

Shields Consult SKF for 2Z – Stamped steel Consult SKF for

NILOS ring options NILOS ring options

4JOHMF
SPX
'PVSQPJOU %PVCMF
SPX
5ISVTU QBDL

BOHVMBS DPOUBDU BOHVMBS DPOUBDU BOHVMBS DPOUBDU BOHVMBS DPOUBDU
CBMM
CFBSJOH CBMM
CFBSJOH CBMM
CFBSJOH CBMM
CFBSJOH
EBUB
UBCMFT
PO
QBHF
 EBUB
UBCMFT
PO
QBHF
 EBUB
UBCMFT
PO
QBHF
 EBUB
UBCMFT
PO
QBHF


50
 Introduction

Introduction Angular contact ball bearings,

SKF standard angular contact ball bearings are

single row Product highlights
Single row angular contact ball bearings can
available with axial clearances, preloads and accommodate combined loads however the
high precision. Single row angular contact ball axial loads can only act in one direction
bearings are designed to accommodate axial High running accuracy and speed
(Figure 1). Under radial loads, a force acting
loads acting in one direction. Under radial capabilities
in the axial direction is produced which must
loads, an induced force acting in the axial Angular contact ball bearings feature
be counteracted. Consequently, the bearings
direction is produced which must be counter- high radial and axial load capacity
are normally adjusted against a second
acted. Consequently, the single bearings are combined with high speed capabilities.
bearing.
normally adjusted against a second bearing. SKF ACBB are made as standard to
The single row angular contact ball bearings
SKF angular contact ball bearings are pro- ISO P6 or ABMA ABEC 3 precision as
shown in the tables have one high and one
duced in a wide variety of designs and sizes. standard.
low shoulder on each ring, enabling a large
Those commonly used in general engineering number of balls to be incorporated. This gives
are shown in this catalog: the bearings relatively high load carrying Universal matching
capacity. The contact angle is 40° (suffix B) Angular contact ball bearings are
• Single row bearings manufactured for universal mounting
• Double row bearings and the bearings are therefore suitable for
heavy axial loads. They are of non-separable in multiple arrangements, including
• Four-point contact ball bearings
design and permit relatively high-speed face-to-face, back-to-back and
• Thrust pack
operation. tandem.
Bearings of the BE design feature an
increased load carrying capacity, and either Large product assortment
Basic design machined brass (M) or glass fiber reinforced Available in a wide range (10 to 240
polyamide 6-6 (P) cages as standard. mm inside bore diameter) with cage
Angular contact ball bearings have raceways in The single row angular contact ball bearings and clearance / preload combinations.
the inner and outer rings that are displaced are produced in two standard versions for The double row design is available with
with respect to each other in the direction of different design purposes. The standard design a choice of shields, seals and snap
the bearing axis. This means that they are (no additional designation suffix such as BEP) rings as well as max-type bearings
particularly suitable for the accommodation of is intended for arrangements where only one with a filling slot. Special application
combined loads; for example, simultaneously bearing is used at each bearing position designs include 4-point contact and
acting radial and axial loads. (Figure 4, page 58). thrust pack.
The axial load carrying capacity of angular The most common version, identified by
contact ball bearings increases with increasing suffix CB (universal matching) is designed for Machined brass cage for heavy
contact angle A. This is defined as the angle arrangements where two or more bearings
between the line joining the points of contact duty applications
are mounted immediately adjacent to each The machined brass cage provides
between the ball and the raceways in the radi- other in random order (back-to-back,
al plane, along which the load is transmitted better performance and longer service
face-to-face or tandem). Because of demand, life under harsh conditions and can be
from one raceway to the other, and a line the larger sized bearings are only produced
perpendicular to the bearing axis. For single used in applications where a standard
with universal matching (suffix CB) (Figure 5, metal or plastic cage is normally used.
row bearings, the magnitude of the contact page 58).
angle is indicated by a suffix in the designation
(B = 40 degrees) (Figure 1). For double row Meets ANSI pump
angular contact ball bearings, the contact requirements
angle is 30 degrees and for QJ four-point SKF Explorer class Angular contact ball bearings are wide-
angular contact ball bearings the contact angle ly used in centrifugal pump applications
is 35 degrees and neither is indicated in the bearings and are manufactured in accordance
nomenclature. High performance SKF Explorer angular con- with ANSI pump standards.
tact ball bearings are printed in blue in the
product tables. SKF Explorer bearings retain
the designation of the earlier standard bear-
ings, e.g. 7208 BECBP. However, each bearing
Figure 1 and its box are marked with the name “SKF
Explorer”. Additional details on SKF Explorer
performance class bearings can be found on
page 23.

51
 Angular contact ball bearings

Introduction

Angular contact ball bearings, Angular contact ball bearings, Variations

double row (Figure 1a) four-point (Figure 1b)
SKF double row ball bearings are designed Four-point contact ball bearings are single row Angular contact ball bearings, single
with solid or one-piece inner and outer rings angular contact ball bearings having raceways row for universal matching
with contact angles converging outside the which are designed to enable axial loads to be These bearings are specially manufactured so
bearing providing overall system rigidity. accommodated in both directions. They need that when mounted in random order (back-to-
The double row angular contact ball bear- less axial space than double row bearings. The back, face-to-face or tandem) (Figure 2), but
ings are available in two styles, Conrad (suffix four-point contact ball bearings shown in the immediately adjacent to each other, the prede-
A) and Max type (suffix E). The more popular following tables have a contact angle of 35° termined value of axial internal clearance or
style is the Conrad type. This assembly uses a and a two-part inner ring, allowing a large preload will be attained. An even distribution of
slight elastic deflection of the outer ring to number of balls to be incorporated, thus load will occur without shims or similar devices.
insert the “last ball”. This results in uninter- providing a high load carrying capacity. The The standard bearings for universal matching
rupted raceways with smooth running, and bearings are separable, i.e. the inner ring carry the suffix CB where C indicates clearance
significant thrust carrying capacity in both halves and the outer ring with ball and cage and B the magnitude of the clearance (Figure 3).
directions. assembly can be mounted individually. Bearings with a smaller or greater clearance
Bearings of the Max type design (suffix E) are also available (suffixes CA and CC, respec-
have a filling slot for inserting the balls. This Angular contact ball bearings, tively) as are bearings with light, moderate or
permits assembly with a greater number of thrust pack heavy preload, (suffixes GA, GB and GC,
balls than in the previously described Conrad respectively where G = preload or negative
A thrust pack bearing consists of a standard
type bearings. clearance). When ordering bearings for univer-
QJ bearing and a single row angular contact
Filling slot bearing features are similar to sal matching; for example 7206 BECB, it is
bearing (BEGAM version) matched together
those of the Conrad type; however, because of necessary to indicate the number of individual
and are intended for applications having
the greater number of balls (with the excep- bearings required since SKF does not stock
predominate axial load in one direction. The
tion of a few sizes) their radial load carrying these in sets.
axial load should not reverse direction during
capacity is often higher than that of the operation except for transient conditions such
Conrad type. On the other hand, heavy thrust as at machine start up or shut-down, else the
loads can be accommodated in only one direc- BEGAM bearing may become unloaded and
tion. These bearings should be mounted so have possible skidding problems. These bear-
that the predominant axial load acting on the ings are matched in sets and are serialized and
shaft is directed away from the filling slot therefore are not interchangeable amongst sets.
(Figure 1a). Thrust loads in the direction of
the filling slot should not exceed a thrust to
radial load ratio of Fa / Fr = 0.3.
Part number markings are normally located Figure 1a Figure 1b
on either the side face or the O.D. The side
face marking is always on the side opposite
1SJNBSZ
UISVTU EJSFDUJPO
the filling slot, and the O.D. marking is offset
from the center away from the side with the
filling slot. Therefore, even double sealed or
shielded bearings with the filling slot covered
from view can be oriented correctly.

%PVCMF
SPX
BOHVMBS DPOUBDU 'PVSQPJOU DPOUBDU

CBMM
CFBSJOH CBMM
CFBSJOH

Figure 2

5BOEFN #BDLUPCBDL 'BDFUPGBDF

BSSBOHFNFOU BSSBOHFNFOU BSSBOHFNFOU

52
 Introduction

Limiting speeds Load carrying capacity of bearing sets

The limiting speeds listed in the bearing tables The values given in the bearing tables for the Special solutions using
are guideline values and are valid for single row
bearings. The values under oil lubrication are
basic dynamic load ratings apply to single bear-
ings. The basic dynamic and static load ratings angular contact ball
maximum values and the values under grease
lubrication are maximum values that can be
for sets of bearings arranged back-to-back,
face-to-face or in tandem is obtained by multi-
bearings
attained using a good quality grease of a soft plying the C value for a single bearings by:
consistency. • Precision angular contact ball bearings
If single bearings are to be adjusted against Two bearings 1.62 x C for machine tools
each other in matched sets of two, three or Three bearings 2.16 x C • Large-size single and double row bearings
four bearings, the limiting speed values given in Four bearings 2.64 x C for heavy engineering applications
the bearing tables must be reduced. Reduction • Hub units produced for the automotive
Where the basic static load rating is industry
factors are given in the table below. concerned, the table value C0 should be
multiplied by the number of bearings in the
The precision angular contact ball bearings
set, 2, 3 or 4.
Reduction factors for limiting speeds are available with a contact angle of 15°
For example, a pair of 7205 BEGAP angular
angular contact ball bearings, single row (suffix CD) or 25° (suffix ACD) and can be
contact ball bearings will have the following
supplied either individually or in matched
values:
sets of two, three or four bearings.
Bearing arrangement Reduction factors
C (single) = 3510 lbs
Details on these special solution products
Two bearings 0.80 C (pair) = 3510 x 1.62 = 5690 lbs
are available in other SKF publications,
Three bearings 0.70 C0 (single) = 2290 lbs which can be supplied upon request.
C0 (pair) = 2290 x 2 = 4580 lbs
Four bearings 0.65
Grease speed (single) = 10000 rpm
Grease speed (pair) = 10000 x 0.8 = 8000 rpm
The C, C0 and speed limits of the pair of
bearings must be used for calculation purposes
in this case.

Figure 3

0
+

Clearance
CC
$#
CA
"YJBM
Axial Axial
"YJBM
preload clearance
QSFMPBE – +
DMFBSBODF
("

GB
GC

–
Preload 0

53
 Angular contact ball bearings
Introduction

Figure 3a

Conrad type
Designations for Conrad type double-row ball bearings with various combinations of seals, shields and snap rings

A A-Z A-2Z ANR A-ZNR A-ZNBR A-2ZNR

A-RS A-2RS A-RSNR A-RSNBR A-2RSNR

Max type
Designations for Max type (single slot) filling slot double-row ball bearings with various combinations of seals, shields and snap rings

E E-Z E-ZB E-2Z E-RSNR E-RSNBR E-2RSNR

E-RS E-RSB E-2RS ENAR E-ZNAR E-ZNABR E-2ZNAR

ENR E-ZNR E-ZNBR E-2ZNR E-RSNAR E-RSNABR E-2RSNAR

54
 Introduction

Angular contact ball bearings, regreased while double sealed bearings are Max type bearings use a suffix A to indicate
double row greased for life. that the snap ring is on the side of the filling
They should not be heated at tempera- slot (NAR). Suffix B in single seal or shield des-
Shielded (Z) and sealed (RS) bearings tures greater than 250° F (120° C) prior ignation indicates that the seal or shield is on
In addition to the open designs, most SKF to mounting and must on no account the opposite side of the filling slot (RSB or ZB).
double row ball bearings are offered with be washed.
shields or seals, on either one or both sides. In Angular contact ball bearings,
most sizes, open bearings also contain seal Snap rings four-point
grooves on the inner and/or outer rings. Snap rings (suffix NR) in the outer ring can
Shields (suffix Z and 2Z) are non-contacting. Locating slots
provide an easy method of locating the bearing
They form a small gap with a chamfer on the in the application. The snap rings and the snap Four-point contact ball bearings are designed
inner ring. They are made from pressed steel ring grooves in the outer rings generally con- to accommodate predominantly axial loads and
and are fixed into an outer ring groove. This form to ABMA Standard 20 and ISO standard are arranged as thrust bearings with radial
non-contacting closure is designed to retain 464. Important snap ring dimensions are clearance in the housing in many applications.
lubricant and exclude larger particles of foreign shown in the deep groove ball bearings section, To permit simple location and prevent rotation
matter. These shielded bearings are primarily Table 4 page 57. of the outer ring, all bearings with an outside
intended for applications with inner ring rota- diameter of 160 mm and above are provided
tion. Single shielded bearings can be used with Combination of seals, shields and snap rings with two locating slots in the outer ring (N2
oil or grease lubrication, while double shielded design). The dimensions of these locating slots
bearings are packed with a predetermined Most bearings are available in various combina- are given in Table 1.
quantity of grease, providing maintenance-free tions of seals, shields and snap rings. (Figure
operation for the life of the bearings. 3a) illustrates the designations for Conrad type
Most bearings are also available with either bearings in various configurations and shows
one or two contacting seals, (suffix -RS and the same for max-type filling slot bearings.
-2RS). The seals consist of an oil and wear In a single sealed or shielded Conrad type
resistant elastomer bonded to a metal plate. bearing with snap ring, the snap ring is nor-
The O.D. of either of the seal is firmly fixed into mally on the opposite side of the seal or shield.
an outer ring groove. The lip at the I.D. of the An additional suffix B indicates the snap ring is
seal contacts an inner ring seal chamfer for on the same side as the seal or shield, e.g. NBR.
effective closure. This seal effectively excludes
solid contaminants and moisture from the
inside surfaces of the bearing. The permissible
operating temperature range for the seals with
a proper lubricant is -40° to +250° F (-40° to
+120° C). Single sealed bearings can be

Table 1

Locating slots in outer ring of four-point contact ball bearings

A
b
D r0
h

A 45°
A-A

Outside Dimensions
diameter
Series QJ 2 Series QJ 3
D
over incl. b h r0 b h r0
mm
in mm in mm in mm in mm in mm in mm in

- 170
6.5 0.256 8.1 0.319 1 0.039 8.5 0.335 10.1 0.398 2 0.079
- 6.6929
170 210
8.5 0.335 10.1 0.398 2 0.787 10.5 0.413 11.7 0.461 2 0.079
6.6929 8.2677
210 270
10.5 0.413 11.7 0.461 2 0.787 10.5 0.413 11.7 0.461 2 0.079
8.2677 10.6299
270 400
10.5 0.413 12.7 0.500 2 0.787 10.5 0.413 12.7 0.500 2 0.079
10.6299 15.784

55
 Angular contact ball bearings

Introduction

Internal clearance Table 2

Axial internal clearance

Unmounted axial internal clearance of single row angular contact ball
single row angular contact ball bearings bearings of series 72B (E), 73B (E) and 74B (B) when arranged in random
Internal clearance in a single row angular con- pairs (back-to-back or face-to-face)
tact ball bearing is only obtained after mounting
and is dependent on adjustment against a sec-
Bore Axial internal clearance
ond bearing that provides axial location in the diameter
opposite direction. CA CB CC
Bearings for universal pairing (suffix CB) are d
the standard SKF bearings for paired mounting over incl. min max min max min max min max min max min max
in random order (back-to-back, face-to-face or mm µm in µm in µm in
tandem). Bearings can be supplied with smaller
axial internal clearance (suffix CA) or larger (suf- - 10 4 12 0.0002 0.0005 14 22 0.0006 0.0009 22 30 0.0009 0.0012
fix CC) or with preload (suffixes GA, GB and GC) 10 18 5 13 0.0002 0.0005 15 23 0.0006 0.0009 24 32 0.0009 0.0013
for universal pairing. 18 30 7 15 0.0003 0.0006 18 26 0.0007 0.0010 32 40 0.0013 0.0016
Bearings identified by suffix CA, CB or CC can
be mounted immediately adjacent to each other 30 50 9 17 0.0004 0.0007 22 30 0.0009 0.0012 40 48 0.0016 0.0019
50 80 11 23 0.0004 0.0009 26 38 0.0010 0.0015 48 60 0.0019 0.0024
in any order and two or more bearings may be 80 120 14 26 0.0006 0.0010 32 44 0.0013 0.0017 55 67 0.0022 0.0026
used. Bearings with preload of the GA, GB and
GC designs can only be arranged in pairs, other- 120 180 17 29 0.0007 0.0011 35 47 0.0014 0.0019 62 74 0.0024 0.0029
wise the preload will increase. 180 250 21 37 0.0008 0.0015 45 61 0.0018 0.0024 74 90 0.0029 0.0035
The values of axial internal clearance for the 250 315 26 42 0.0010 0.0017 52 68 0.0020 0.0027 90 106 0.0035 0.0042
classes CA, CB and CC can be found in Table 2.
They are valid for bearings arranged back-to-
Radial clearance [~=] 0.85 axial clearance.
back or face-to-face before mounting and under
zero measuring load. Preload values for classes
GA, GB and GC are given in Table 2a. Table 3
shows a conversion from the old preload
suffices to the current suffix.

Table 2a

Unmounted preload of single row angular contact ball bearings of series 72B (E),
73B (E) and 74 (B) when arranged in random pairs (back-to-back or face-to-face)

Bore Preload
diameter
GA GB GC
d
over incl. min max min max max max min max min max min max min max min max min max min max min max
mm µm in N lbf µm in N lbf µm in N lbf

10 18 4 -4 0.0002 -0.0002 80 18 -2 -10 -0.0001 -0.0004 30 330 7 74 -8 -16 -0.0003 -0.0006 230 660 52 149
18 30 4 -4 0.0002 -0.0002 120 27 -2 -10 -0.0001 -0.0004 40 480 9 108 -8 -16 -0.0003 -0.0006 340 970 76 218
30 50 4 -4 0.0002 -0.0002 160 36 -2 -10 -0.0001 -0.0004 60 630 13 142 -8 -16 -0.0003 -0.0006 450 1 280 101 288

50 80 6 -6 0.0002 -0.0002 380 86 -3 -15 -0.0001 -0.0006 140 1 500 31 338 -12 -24 -0.0005 -0.0009 1 080 3 050 243 686
80 120 6 -6 0.0002 -0.0002 410 92 -3 -15 -0.0001 -0.0006 150 1 600 34 360 -12 -24 -0.0005 -0.0009 1 150 3 250 259 731
120 180 6 -6 0.0002 -0.0002 540 122 -3 -15 -0.0001 -0.0006 200 2 150 45 484 -12 -24 -0.0005 -0.0009 1 500 4 300 337 968

180 250 8 -8 0.0003 -0.0003 940 212 -4 -20 -0.0002 -0.0008 330 3 700 74 833 -16 -32 -0.0006 -0.0013 2 650 7 500 596 1 688
250 315 8 -8 0.0003 -0.0003 1 080 243 -4 -20 -0.0002 -0.0008 380 4 250 85 956 -16 -32 -0.0006 -0.0013 3 000 8 600 674 1 935

56
 Introduction

Axial internal clearance double row Table 3

angular contact ball bearings
Internal clearances for double row angular Old/new preload designation interchange,
contact ball bearings differ from deep groove single row angular contact ball bearings 72xx, 73xx and 74xx series
ball bearings in that axial rather than radial
clearance is specified. Table 4 shows the axial Bore Bore Old preload suffix
clearance of the SKF double row angular contact size diameter
bearings in four standard clearance ranges; C2
(mm) G02 G05 G1* G2 G3 G5
(less than normal clearance), normal clearance,
C3 (greater than normal clearance), and C4
(greater than C3 clearance). These are valid 00 10 GB GB GC – – –
for bearings before mounting under zero 01 12 GB GB GC – – –
measuring load. 02 15 GB GB GC – – –
03 17 GB GB GC – – –
Axial internal clearance 04 20 GA GB GC – – –
four-point contact ball bearings 06 30 GA GB GC – – –
Standard manufacture SKF four-point contact 07 35 GA GB GB GC – –
08* 40* GA GB GB* GC – –
ball bearings have Normal axial internal clear-
09 45 GA GB GB GC – –
ance. Most sizes can also be supplied with
10 50 GA GB GB GC – –
greater or smaller internal clearance than
11 55 GA GA GB GB GB GC
Normal. Availability should be checked before
12 60 GA GA GB GB GB GC
ordering.
13 65 GA GA GB GB GB GC
The values for the axial internal clearance are
14 70 GA GA GB GB GB GC
shown in Table 5 and are for bearings before
15 75 GA GA GB GB GB GC
mounting under zero measuring load. 16 80 GA GA GB GB GB GC
Old versus new designations 17 85 GA GA GB GB GB GC
18 90 GA GA GB GB GB GC
on SRACBB (Table 3)
19 95 GA GA GB GB GB GC
Use this table to determine which new preload 20 100 GA GA GB GB GB GC
designations replace old preload designations. 21 105 GA GA GB GB GB GC
Simply find the bearing bore size/diameter on 22 110 GA GA GB GB GB GC
the left, and the old preload across the top. The 24 120 GA GA GB GB GB GC
new designation is at the point where the bore 26 130 GA GA GB GB GB GC
size/diameter row intersects with the old preload 28 140 GA GA GB GB GB GC
column. 30 150 GA GA GB GB GB GC
*Example: 7308 BEAG1Y = 08 bore size, 32 160 GA GA GB GB GB GC
34 170 GA GA GB GB GB GC
40 mm bore diameter
36 180 GA GA GB GB GB GC
G1 (100 lbs) preload
Replace with: 7308 BEGBY

Table 4

Axial internal clearance of Conrad type and filling slot double row angular contact ball bearings
32 and 33 series (values in 0.001 mm)

Bore Axial internal clearance

diameter
C2 Normal C3 C4
d
over incl. min max min max min max min max min max min max min max min max
mm µm in µm in µm in µm in

- 10 1 11 0.0000 0.0004 5 21 0.0002 0.0008 12 28 0.0005 0.0011 40 60 0.0016 0.0024

10 18 1 12 0.0000 0.0005 6 23 0.0002 0.0009 13 31 0.0005 0.0012 42 64 0.0017 0.0025
18 24 2 14 0.0001 0.0006 7 25 0.0003 0.0010 16 34 0.0006 0.0013 43 69 0.0017 0.0027

24 30 2 15 0.0001 0.0006 8 27 0.0003 0.0011 18 37 0.0007 0.0015 45 75 0.0018 0.0030

30 40 2 16 0.0001 0.0006 9 29 0.0004 0.0011 21 40 0.0008 0.0016 48 84 0.0019 0.0033
40 50 2 18 0.0001 0.0007 11 33 0.0004 0.0013 23 44 0.0009 0.0017 51 90 0.0020 0.0035

50 65 3 22 0.0001 0.0009 13 36 0.0005 0.0014 26 48 0.0010 0.0019 55 96 0.0022 0.0038

65 80 3 24 0.0001 0.0009 15 40 0.0006 0.0016 30 54 0.0012 0.0021 61 106 0.0024 0.0042
80 100 3 26 0.0001 0.0010 18 46 0.0007 0.0018 35 63 0.0014 0.0025 70 123 0.0028 0.0048

100 110 4 30 0.0002 0.0012 22 53 0.0009 0.0021 42 73 0.0017 0.0029 80 148 0.0031 0.0058

57
 Angular contact ball bearings
Introduction

Table 5

Axial internal clearance of four-point contact ball bearings

Bore Axial internal clearance

diameter
d C2 Normal C3 C4
over incl. min max min max min max min max min max min max min max min max
mm in mm in µm in µm in µm in µm in

10 18 0.3937 0.7087 15 55 0.0006 0.0022 45 85 0.0018 0.0033 75 125 0.0030 0.0049 115 165 0.0045 0.0065
18 40 0.7087 1.5748 26 66 0.0010 0.0026 56 106 0.0022 0.0042 96 146 0.0038 0.0057 136 186 0.0054 0.0073
40 60 1.5748 2.3622 36 86 0.0014 0.0034 76 126 0.0030 0.0050 116 166 0.0046 0.0065 156 206 0.0061 0.0081

60 80 2.3622 3.1496 46 96 0.0018 0.0038 86 136 0.0034 0.0054 126 176 0.0050 0.0069 166 226 0.0065 0.0089
80 100 3.1496 3.9370 56 106 0.0022 0.0042 96 156 0.0038 0.0061 136 196 0.0054 0.0077 186 246 0.0073 0.0097
100 140 3.9370 5.5118 66 126 0.0026 0.005 116 176 0.0046 0.0069 156 216 0.0061 0.0085 206 266 0.0081 0.0105

140 180 5.5118 7.0866 76 156 0.0030 0.0061 136 196 0.0054 0.0077 176 246 0.0069 0.0097 226 296 0.0089 0.0116
180 220 7.0866 8.6614 96 176 0.0038 0.0069 156 226 0.0061 0.0089 206 276 0.0081 0.0109 256 326 0.0101 0.0128

Radial clearance [~=] 0.7 axial clearance.

Design of bearing arrangements Figure 4 Figure 5

When designing bearing arrangements using
single row angular contact ball bearings it is
necessary to pay attention to the special
characteristics of the bearings. Because of
their internal design they cannot be used singly
and must be used either with a second bearing
(Figure 4) or as bearing sets (Figure 5).
As already mentioned under "Internal clear-
ance", it is necessary to adjust the two single
row angular contact ball bearings of an
arrangement against each other until the
operational clearance or requisite preload is
obtained.
Arrangements using bearings for universal
mounting, where the bearings are immediately
adjacent to each other, do not require adjust-
ment. Here, the required operational preload or
clearance is obtained by choosing an appropriate
preload or clearance class as well as suitable
fits for the bearings in the housing and on the
shaft. For more specific mounting instructions
visit the SKF website at www.skf.com/mount or
contact SKF Applications Engineering.

58
 Introduction

Loads Equivalent dynamic bearing load for Minimum load

four-point contact bearings
Equivalent dynamic bearing load for In order to provide satisfactory opera-
When four-point contact ball bearings with a
single row bearings of the B and BE tion of all ball and roller bearings they
contact angle of 35° are used as locating bear-
designs when mounted as single ings to accommodate radial and axial loads, the
must always be subjected to a given
bearings or paired in tandem equivalent dynamic bearing load can be minimum load.
obtained from This is also true of angular contact ball bear-
P = Fr when Fa / Fr ≤ 1.14 ings, particularly if they run at high speeds
P = 0.35 Fr + 0.57 Fa when Fa / Fr > 1.14 P = Fr + 0.66 Fa where the inertia forces of the balls and cage,
when Fa / Fr ≤ 0.95 and the friction in the lubricant can have a
where detrimental influence on the rolling conditions
P = equivalent dynamic bearing load P = 0.6 Fr + 1.07 Fa in the bearing and may cause damaging sliding
Fr = radial load acting on the bearing when Fa / Fr > 0.95 movements to occur between the balls and the
Fa = axial load acting on the bearing raceways.
It should be remembered that satisfactory The requisite minimum radial load to be
When determining the axial force Fa performance of the ball set of four-point applied in such cases can be determined by
reference should be made to the following contact ball bearings is only obtained when the using the Interactive Engineering Catalog on
section. balls are in contact with the raceways at two the SKF website www.skf.com or by contacting
points, i.e. when the axial load SKF Applications Engineering. However, the
weight of the components supported by the
Equivalent dynamic bearing load for bearing, together with the external forces, often
Fa ≥ 1.27 Fr
bearings mounted in pairs, back-to- exceeds the requisite minimum load. If this is
back or face-to-face If the four-point contact ball bearing is used not the case, an additional radial load must be
as a thrust bearing in combination with other applied to the bearing; for example, by increas-
P = Fr + 0.55 Fa radial bearings, and it is mounted with radial ing belt tension, by applying a preload to the
when Fa / Fr ≤ 1.14 clearance in the housing, the equivalent inner or outer rings, or by using springs.
dynamic bearing load becomes
P = 0.57 Fr + 0.93 Fa
when Fa / Fr > 1.14 P = 1.07 Fa
Frequency vibration data
Frequency vibration data is available on the
Fa and Fr are the forces acting on the
SKF website www.skf.com in the Interactive
bearing pair.
Engineering Catalog or by contacting SKF
Applications Engineering.
Equivalent dynamic bearing load for
double row bearings
For the double row angular contact bearings
described in this catalog, the equivalent
dynamic bearing load is

P = XFr + YFa

where
P = equivalent dynamic bearing load
X = radial load factor for the bearing
Y = axial load factor for the bearing
Fr = actual radial bearing load
Fa = actual axial bearing load

X and Y factors are given for each bearing in

Table 6a for Conrad type and Table 6b for Max
type they change depending on the load ratio
Fa / Fr in relationship to the reference value e.

59
 Angular contact ball bearings
Introduction

Table 6a

Calculation factors for double row angular contact ball bearings,

Conrad type

Designation Dynamic Static

Fa / Fr ≤ e Fa / Fr ≥ e

e X Y X Y Y0

3200 A 0.80 1 0.78 0.63 1.24 0.66

3201 A 0.80 1 0.78 0.63 1.24 0.66
3202 A 0.80 1 0.78 0.63 1.24 0.66
3203 A 0.80 1 0.78 0.63 1.24 0.66
3204 A 0.80 1 0.78 0.63 1.24 0.66
3205 A 0.80 1 0.78 0.63 1.24 0.66
3206 A 0.80 1 0.78 0.63 1.24 0.66
3207 A 0.80 1 0.78 0.63 1.24 0.66
3208 A 0.80 1 0.78 0.63 1.24 0.66
3209 A 0.80 1 0.78 0.63 1.24 0.66
3210 A 0.80 1 0.78 0.63 1.24 0.66
3211 A 0.80 1 0.78 0.63 1.24 0.66
3212 A 0.80 1 0.78 0.63 1.24 0.66
3213 A 0.80 1 0.78 0.63 1.24 0.66
3214 A 0.80 1 0.78 0.63 1.24 0.66
3215 A 0.80 1 0.78 0.63 1.24 0.66
3216 A 0.80 1 0.78 0.63 1.24 0.66
3217 A 0.80 1 0.78 0.63 1.24 0.66
3218 A 0.80 1 0.78 0.63 1.24 0.66
3219 A 0.80 1 0.78 0.63 1.24 0.66
3220 A 0.80 1 0.78 0.63 1.24 0.66

3304 A 0.80 1 0.78 0.63 1.24 0.66

3305 A 0.80 1 0.78 0.63 1.24 0.66
3306 A 0.80 1 0.78 0.63 1.24 0.66
3307 A 0.80 1 0.78 0.63 1.24 0.66
3308 A 0.80 1 0.78 0.63 1.24 0.66
3309 A 0.80 1 0.78 0.63 1.24 0.66
3310 A 0.80 1 0.78 0.63 1.24 0.66
3311 A 0.80 1 0.78 0.63 1.24 0.66
3312 A 0.80 1 0.78 0.63 1.24 0.66
3313 A 0.80 1 0.78 0.63 1.24 0.66
3314 A 0.80 1 0.78 0.63 1.24 0.66
3315 A 0.80 1 0.78 0.63 1.24 0.66
3316 A 0.80 1 0.78 0.63 1.24 0.66
3317 A 0.80 1 0.78 0.63 1.24 0.66
3318 A 0.80 1 0.78 0.63 1.24 0.66

60
 Introduction

Table 6b

Calculation factors for double row angular contact ball bearings,

Max type

Designation Dynamic Static

Fa / Fr ≤ e Fa / Fr ≥ e

e X Y X Y Y0

3204 E 0.68 1 0.92 0.67 1.44 0.76

3205 E 0.68 1 0.92 0.67 1.44 0.76
3206 E 0.68 1 0.92 0.67 1.44 0.76
3207 E 0.80 1 0.78 0.63 1.24 0.66
3208 E 0.80 1 0.78 0.63 1.24 0.66
3209 E 0.80 1 0.78 0.63 1.24 0.66
3210 E 0.80 1 0.78 0.63 1.24 0.66
3211 E 0.80 1 0.78 0.63 1.24 0.66
3212 E 0.80 1 0.78 0.63 1.24 0.66
3213 E 0.80 1 0.78 0.63 1.24 0.66
3214 E 0.80 1 0.78 0.63 1.24 0.66
3215 E 0.80 1 0.78 0.63 1.24 0.66
3216 E 0.80 1 0.78 0.63 1.24 0.66
3217 E 0.80 1 0.78 0.63 1.24 0.66
3218 E 0.80 1 0.78 0.63 1.24 0.66

3304 E 0.80 1 0.78 0.63 1.24 0.66

3305 E 0.80 1 0.78 0.63 1.24 0.66
3306 E 0.80 1 0.78 0.63 1.24 0.66
3307 E 0.80 1 0.78 0.63 1.24 0.66
3308 E 0.80 1 0.78 0.63 1.24 0.66
3309 E 0.80 1 0.78 0.63 1.24 0.66
3310 E 0.80 1 0.78 0.63 1.24 0.66
3311 E 0.80 1 0.78 0.63 1.24 0.66
3312 E 0.80 1 0.78 0.63 1.24 0.66
3313 E 0.80 1 0.78 0.63 1.24 0.66
3314 E 0.80 1 0.78 0.63 1.24 0.66
3315 E 0.80 1 0.78 0.63 1.24 0.66
3316 E 0.80 1 0.78 0.63 1.24 0.66

61
 Angular contact ball bearings
Single row
B
Standard and SKF Explorer
Series: 7200 BE — 7248 B
Size: 10 mm — 240 mm
0.3937 in — 9.4488 in

D d

These bearings are typically mounted in pairs. Refer to page 52 for details.

Designation Principal dimensions Basic load ratings Speed rating Mass

Bore Outside diameter Width Dynamic Static Reference Limiting

d D B C C0 speed speed
mm in mm in mm in N lbf N lbf r/min r/min kg lb

7200 BE 10 0.3937 30 1.1811 9 0.3543 7 020 1 580 3 350 750 30 000 30 000 0.03 0.07
7201 BE 12 0.4724 32 1.2598 10 0.3937 7 610 1 710 3 800 850 26 000 26 000 0.04 0.08
7202 BE 15 0.5906 35 1.3780 11 0.4331 8 840 1 990 4 800 1 080 24 000 24 000 0.05 0.10

7203 BE 17 0.6693 40 1.5748 12 0.4724 11 000 2 470 6 100 1 370 22 000 22 000 0.07 0.15
7204 BE 20 0.7874 47 1.8504 14 0.5512 13 300 2 990 8 300 1 870 18 000 19 000 0.11 0.24
7205 BE 25 0.9843 52 2.0472 15 0.5906 15 600 3 510 10 200 2 290 17 000 17 000 0.14 0.31

7206 BE 30 1.1811 62 2.4409 16 0.6299 24 000 5 400 15 600 3 510 14 000 14 000 0.21 0.46
7207 BE 35 1.3780 72 2.8346 17 0.6693 31 000 6 970 20 800 4 680 12 000 12 000 0.30 0.66
7208 BE 40 1.5748 80 3.1496 18 0.7087 36 500 8 210 26 000 5 840 11 000 11 000 0.39 0.86

7209 BE 45 1.7717 85 3.3465 19 0.7480 38 000 8 540 28 000 6 290 10 000 10 000 0.44 0.97
7210 BE 50 1.9685 90 3.5433 20 0.7874 40 000 8 990 30 500 6 860 9 000 9 000 0.51 1.12
7211 BE 55 2.1654 100 3.9370 21 0.8268 46 200 10 400 38 000 8 540 7 500 8 000 0.66 1.46

7212 BE 60 2.3622 110 4.3307 22 0.8661 61 000 13 700 45 500 10 200 7 500 7 500 0.85 1.88
7213 BE 65 2.5591 120 4.7244 23 0.9055 66 300 14 900 54 000 12 100 6 300 6 700 1.10 2.43
7214 BE 70 2.7559 125 4.9213 24 0.9449 72 000 16 200 60 000 13 500 6 700 6 700 1.18 2.61

7215 BE 75 2.9528 130 5.1181 25 0.9843 70 200 15 800 64 000 14 400 5 600 6 000 1.29 2.80
7216 BE 80 3.1496 140 5.5118 26 1.0236 85 000 19 100 73 500 16 500 5 600 5 600 1.59 3.50
7217 BE 85 3.3465 150 5.9055 28 1.1024 95 600 21 500 83 000 18 700 5 000 5 300 1.99 4.40

7218 BE 90 3.5433 160 6.2992 30 1.1811 108 000 24 300 96 500 21 700 4 500 4 800 2.41 5.30
7219 BE 95 3.7402 170 6.6929 32 1.2598 129 000 29 000 108 000 24 300 4 800 4 800 2.95 6.50
7220 BE 100 3.9370 180 7.0866 34 1.3386 135 000 30 300 122 000 27 400 4 000 4 300 3.61 8.00

7221 BE 105 4.1339 190 7.4803 36 1.4173 148 000 33 300 137 000 30 800 3 800 4 000 4.18 9.20
7222 BE 110 4.3307 200 7.8740 38 1.4961 153 000 34 400 153 000 34 400 3 600 3 800 4.95 10.90
7224 B 120 4.7244 215 8.4646 40 1.5748 165 000 37 100 163 000 36 600 3 400 3 600 5.89 13.00

7226 B 130 5.1181 230 9.0551 40 1.5748 186 000 41 800 193 000 43 400 3 200 3 400 6.76 14.90
7228 B 140 5.5118 250 9.8425 42 1.6535 199 000 44 700 196 000 44 100 2 800 3 000 8.83 19.50
7230 B 150 5.9055 270 10.6299 45 1.7717 216 000 48 600 224 000 50 400 2 600 2 800 10.80 23.80

7232 B 160 6.2992 290 11.4173 48 1.8898 255 000 57 300 236 000 53 100 2 400 2 600 13.60 30.00
7234 B 170 6.6929 310 12.2047 52 2.0472 281 000 63 200 270 000 60 700 2 400 2 400 16.70 36.80
7236 B 180 7.0866 320 12.5984 52 2.0472 291 000 65 400 320 000 71 900 2 200 2 400 17.60 38.80

7238 B 190 7.4803 340 13.3858 55 2.1654 307 000 69 000 355 000 79 800 2 000 2 200 21.90 48.30
7248 B 240 9.4488 440 17.3228 72 2.8346 364 000 81 800 540 000 121 400 1 600 1 700 49.00 108.00

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

62
 B
Single row
Standard and SKF Explorer
Series: 7301 BE — 7330 B
Size: 12 mm — 150 mm
0.4724 in — 5.9055 in

D d

These bearings are typically mounted in pairs. Refer to page 52 for details.

Designation Principal dimensions Basic load ratings Speed rating Mass

Bore Outside diameter Width Dynamic Static Reference Limiting

d D B C C0 speed speed
mm in mm in mm in N lbf N lbf r/min r/min kg lb

7301 BE 12 0.4724 37 1.4567 12 0.4724 10 600 2 400 5 000 1 120 24 000 24 000 0.06 0.10
7302 BE 15 0.5906 42 1.6535 13 0.5118 13 000 2 900 6 700 1 510 20 000 20 000 0.08 0.20
7303 BE 17 0.6693 47 1.8504 14 0.5512 15 900 3 600 8 300 1 870 19 000 19 000 0.11 0.20

7304 BE 20 0.7874 52 2.0472 15 0.5906 19 000 4 300 10 400 2 340 18 000 18 000 0.15 0.30
7305 BE 25 0.9843 62 2.4409 17 0.6693 26 500 6 000 15 600 3 510 15 000 15 000 0.24 0.50
7306 BE 30 1.1811 72 2.8346 19 0.7480 35 500 8 000 21 200 4 770 13 000 13 000 0.37 0.80

7307 BE 35 1.3780 80 3.1496 21 0.8268 41 500 9 300 24 500 5 510 11 000 11 000 0.49 1.10
7308 BE 40 1.5748 90 3.5433 23 0.9055 50 000 11 200 33 500 7 530 10 000 10 000 0.68 1.50
7309 BE 45 1.7717 100 3.9370 25 0.9843 61 000 13 700 41 500 9 300 9 000 9 000 0.90 2.00

7310 BE 50 1.9685 110 4.3307 27 1.0630 75 000 16 900 51 000 11 500 8 000 8 000 1.16 2.60
7311 BE 55 2.1654 120 4.7244 29 1.1417 85 000 19 100 60 000 13 500 7 000 7 000 1.49 3.30
7312 BE 60 2.3622 130 5.1181 31 1.2205 104 000 23 400 69 500 15 600 6 700 6 700 1.88 4.10

7313 BE 65 2.5591 140 5.5118 33 1.2992 116 000 26 100 80 000 18 000 6 300 6 300 2.31 5.10
7314 BE 70 2.7559 150 5.9055 35 1.3780 127 000 28 500 90 000 20 200 5 600 5 600 2.83 6.20
7315 BE 75 2.9528 160 6.2992 37 1.4567 132 000 29 700 106 000 23 800 5 300 5 300 3.26 7.20

7316 BE 80 3.1496 170 6.6929 39 1.5354 143 000 32 100 118 000 26 500 5 000 5 000 4.03 8.90
7317 BE 85 3.3465 180 7.0866 41 1.6142 156 000 35 100 132 000 29 700 4 800 4 800 4.74 10.40
7318 BE 90 3.5433 190 7.4803 43 1.6929 166 000 37 300 146 000 32 800 4 500 4 500 5.53 12.20

7319 BE 95 3.7402 200 7.8740 45 1.7717 180 000 40 500 163 000 36 600 4 300 4 300 6.41 14.10
7320 BE 100 3.9370 215 8.4646 47 1.8504 216 000 48 600 190 000 42 700 4 000 4 000 8.00 17.60
7321 BE 105 4.1339 225 8.8583 49 1.9291 203 000 45 600 208 000 46 800 3 400 3 600 9.12 20.10

7322 BE 110 4.3307 240 9.4488 50 1.9685 225 000 50 600 224 000 50 400 3 200 3 400 10.70 23.60
7324 B 120 4.7244 260 10.2362 55 2.1654 238 000 53 500 250 000 56 200 3 000 3 200 13.80 30.40
7326 B 130 5.1181 280 11.0236 58 2.2835 296 000 66 500 270 000 60 700 2 800 2 800 17.10 37.70

7328 B 140 5.5118 300 11.8110 62 2.4409 302 000 67 900 310 000 69 700 2 600 2 600 21.30 47.00
7330 B 150 5.9055 320 12.5984 65 2.5591 332 000 74 600 365 000 82 100 2 400 2 400 25.00 55.10

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

63
 Angular contact ball bearings
Single row B
Standard
Series: 7334 B — 7344 B
Size: 170 mm — 220 mm
6.6929 in — 8.6614 in

Series: 7405 B — 7432

D d
Size: 25 mm — 160 mm
0.9843 in — 6.2992 in

These bearings are typically mounted in pairs. Refer to page 52 for details.

Designation Principal dimensions Basic load ratings Speed rating Mass

Bore Outside diameter Width Dynamic Static Reference Limiting

d D B C C0 speed speed
mm in mm in mm in N lbf N lbf r/min r/min kg lb

7334 B 170 6.6929 360 14.1732 72 2.8346 390 000 87 700 455 000 102 300 2 000 2 200 34.60 76.30
7336 B 180 7.0866 380 14.9606 75 2.9528 410 000 92 200 490 000 110 200 2 000 2 000 40.00 88.20
7338 B 190 7.4803 400 15.7480 78 3.0709 442 000 99 400 560 000 125 900 1 900 1 900 48.30 106.50

7340 B 200 7.8740 420 16.5354 80 3.1496 462 000 103 900 655 000 147 200 1 800 1 800 52.80 116.40
7344 B 220 8.6614 460 18.1102 88 3.4645 494 000 111 100 720 000 161 900 1 600 1 700 70.00 154.30

7405 B 25 0.9843 80 3.1496 21 0.8268 39 700 8 900 23 600 5 300 11 000 11 000 0.61 1.30
7406 B 30 1.1811 90 3.5433 23 0.9055 47 500 10 700 29 000 6 500 10 000 10 000 0.85 1.90
7407 B 35 1.3780 100 3.9370 25 0.9843 60 500 13 600 38 000 8 500 8 500 9 000 1.10 2.40

7408 B 40 1.5748 110 4.3307 27 1.0630 70 200 15 800 45 500 10 200 8 000 8 000 1.40 3.10
7409 B 45 1.7717 120 4.7244 29 1.1417 85 200 19 200 55 000 12 400 7 000 7 500 1.80 4.00
7410 B 50 1.9685 130 5.1181 31 1.2205 95 600 21 500 64 000 14 400 6 300 6 700 2.25 5.00

7411 B 55 2.1654 140 5.5118 33 1.2992 111 000 25 000 76 500 17 200 6 000 6 300 2.75 6.10
7412 B 60 2.3622 150 5.9055 35 1.3780 119 000 26 800 86 500 19 400 5 600 5 600 3.30 7.30
7413 B 65 2.5591 160 6.2992 37 1.4567 130 000 29 200 96 500 21 700 5 000 5 300 3.85 8.50

7414 B 70 2.7559 180 7.0866 42 1.6535 159 000 35 700 127 000 28 500 4 500 4 800 5.00 11.00
7415 B 75 2.9528 190 7.4903 45 1.7717 168 000 37 800 140 000 31 500 4 300 4 500 6.85 15.10
7416 B 80 3.1496 200 7.8740 48 1.8898 178 000 40 000 153 000 34 400 4 000 4 300 8.00 17.60

7417 B 85 3.3465 210 8.2677 52 2.0472 190 000 42 700 166 000 37 300 3 800 4 000 10.30 22.70
7418 90 3.5433 225 8.8583 54 2.1260 216 000 48 600 200 000 45 000 3 600 3 800 11.50 25.40
7419 95 3.7402 250 9.8425 55 2.1654 251 000 56 400 245 000 55 100 3 400 3 400 13.50 29.80

7420 100 3.9370 265 10.4331 60 2.3622 276 000 62 000 275 000 61 800 3 200 3 200 15.50 34.20
7432 160 6.2992 400 15.7480 88 3.4646 468 000 105 200 610 000 137 100 2 200 2 200 59.14 130.40

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

64
 Single row
B
Four-point ACBB
Standard and SKF Explorer
Series: QJ 202 N2MA — QJ 252 N2MA
Size: 15 mm — 260 mm
0.5906 in — 10.2362 in

D d

"N2" Design
N2 Design

These bearings are typically mounted in pairs. Refer to page 52 for details.

Designation Principal dimensions Basic load ratings Speed rating Mass

Bore Outside diameter Width Dynamic Static Reference Limiting

d D B C C0 speed speed
mm in mm in mm in N lbf N lbf r/min r/min kg lb

QJ 202 N2MA 15 0.5906 35 1.3780 11 0.4331 12 700 2 850 8 300 1 870 22 000 36 000 0.06 0.14
QJ 203 N2MA 17 0.6693 40 1.5748 12 0.4724 15 900 3 570 10 600 2 380 19 000 30 000 0.08 0.18
QJ 205 MA 25 0.9843 52 2.0472 15 0.5906 27 000 6 070 21 200 4 770 16 000 22 000 0.16 0.35

QJ 206 MA 30 1.1811 62 2.4409 16 0.6299 37 500 8 430 30 500 6 860 14 000 19 000 0.24 0.53
QJ 207 N2MA 35 1.3780 72 2.8346 17 0.6693 49 000 11 020 41 500 9 330 12 000 17 000 0.36 0.79
QJ 208 MA 40 1.5748 80 3.1496 18 0.7087 56 000 12 590 49 000 11 020 11 000 15 000 0.45 0.99

QJ 209 MA 45 1.7717 85 3.3465 19 0.7480 63 000 14 160 56 000 12 590 10 000 14 000 0.52 1.15
QJ 210 MA 50 1.9685 90 3.5433 20 0.7874 65 500 14 720 61 000 13 710 9 000 13 000 0.59 1.30
QJ 211 MA 55 2.1654 100 3.9370 21 0.8268 85 000 19 110 83 000 18 660 8 000 11 000 0.77 1.70

QJ 212 MA 60 2.3622 110 4.3307 22 0.8661 96 500 21 690 93 000 20 910 7 500 10 000 0.99 2.18
QJ 212 N2PHAS 60 2.3622 110 4.3307 22 0.8661 96 500 21 690 93 000 20 910 8 500 10 000 0.89 1.96
QJ 213 MA 65 2.5591 120 4.7244 23 0.9055 110 000 24 730 112 000 25 180 6 700 9 500 1.20 2.60

QJ 214 MA 70 2.7559 125 4.9213 24 0.9449 120 000 27 000 122 000 27 430 6 300 9 000 1.32 2.90
QJ 215 MA 75 2.9528 130 5.1181 25 0.9843 125 000 28 100 132 000 29 670 6 300 8 500 1.45 3.20
QJ 216 MA 80 3.1496 140 5.5118 26 1.0236 146 000 32 800 156 000 35 100 5 600 8 000 1.85 4.10

QJ 217 MA 85 3.3465 150 5.9055 28 1.1024 156 000 35 100 173 000 38 900 5 300 7 500 2.25 5.00
QJ 218 N2MA 90 3.5433 160 6.2992 30 1.1811 186 000 41 800 200 000 45 000 5 000 7 000 2.75 6.10
QJ 219 N2MA 95 3.7402 170 6.6929 32 1.2598 212 000 47 700 232 000 52 200 4 800 6 700 3.35 7.40

QJ 220 N2MA 100 3.9370 180 7.0866 34 1.3386 236 000 53 100 265 000 59 600 4 500 6 300 4.05 8.90
QJ 222 N2MA 110 4.3370 200 7.8740 38 1.4961 280 000 62 900 325 000 73 100 4 000 5 600 5.60 12.30
QJ 224 N2MA 120 4.7244 215 8.4646 40 1.5748 300 000 67 400 365 000 82 100 3 600 5 000 6.95 15.30

QJ 226 N2MA 130 5.1181 230 9.0551 40 1.5748 310 000 69 700 400 000 89 900 3 400 4 800 7.75 17.10
QJ 228 N2MA 140 5.5118 250 9.8425 42 1.6535 345 000 77 600 475 000 106 800 3 200 4 300 9.85 21.70
QJ 230 N2MA 150 5.9055 270 10.6299 45 1.7717 400 000 89 900 570 000 128 100 3 000 4 000 12.50 27.60

QJ 232 N2MA 160 6.2992 290 11.4173 48 1.8898 450 000 101 200 670 000 150 600 2 800 3 800 15.50 34.20
QJ 234 N2MA 170 6.6929 310 12.2047 52 2.0472 455 000 102 300 720 000 161 900 2 600 3 400 19.50 43.00
QJ 236 N2MA 180 7.0866 320 12.5984 52 2.0472 475 000 106 800 765 000 172 000 2 400 3 400 20.50 45.20

QJ 240 N2MA 200 7.8740 360 14.1732 58 2.2835 540 000 121 400 915 000 205 700 1 800 3 000 28.50 62.80
QJ 248 N2MA 240 9.4488 440 17.3228 72 2.8346 650 000 146 100 1 200 000 269 800 1 500 2 400 53.00 116.80
QJ 252 N2MA 260 10.2362 480 18.8976 80 3.1496 728 000 163 700 1 430 000 321 500 1 300 2 200 68.00 149.90

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

65
 Angular contact ball bearings
Single row
B
Four-point ACBB
Standard and SKF Explorer
Series: QJ 303 N2MA — QJ 344 N2MA
Size: 17 mm — 220 mm
0.6693 in — 8.6614 in

D d

"N2" Design
N2 Design

Designation Principal dimensions Basic load ratings Speed rating Mass

Bore Outside diameter Width Dynamic Static Reference Limiting

d D B C C0 speed speed
mm in mm in mm in N lbf N lbf r/min r/min kg lb

QJ 303 N2MA 17 0.6693 47 1.8504 14 0.5512 23 400 5 260 15 000 3 370 17 000 28 000 0.14 0.30
QJ 304 MA 20 0.7874 52 2.0472 15 0.5906 32 000 7 190 21 600 4 860 18 000 24 000 0.18 0.40
QJ 305 MA 25 0.9843 62 2.4409 17 0.6693 39 000 8 770 28 000 6 290 12 000 20 000 0.29 0.60

QJ 306 MA 30 1.1811 72 2.8346 19 0.7480 53 000 11 910 41 500 9 330 12 000 17 000 0.42 0.90
QJ 307 MA 35 1.3780 80 3.1496 21 0.8268 64 000 14 390 51 000 11 460 11 000 15 000 0.57 1.30
QJ 308 MA 40 1.5748 90 3.5433 23 0.9055 78 000 17 530 64 000 14 390 10 000 14 000 0.78 1.70

QJ 309 MA 45 1.7717 100 3.9370 25 0.9843 100 000 22 480 83 000 18 700 9 000 12 000 1.05 2.30
QJ 310 MA 50 1.9685 110 4.3307 27 1.0630 118 000 26 530 100 000 22 500 8 000 11 000 1.35 3.00
QJ 311 MA 55 2.1654 120 4.7244 29 1.1417 137 000 30 800 118 000 26 500 7 000 10 000 1.75 3.90

QJ 312 MA 60 2.3622 130 5.1181 31 1.2205 156 000 35 100 137 000 30 800 6 700 9 000 2.15 4.70
QJ 313 MA 65 2.5591 140 5.5118 33 1.2992 176 000 39 600 156 000 35 100 6 300 8 500 2.70 6.00
QJ 314 MA 70 2.7559 150 5.9055 35 1.3780 200 000 45 000 180 000 40 500 5 600 8 000 3.15 6.90

QJ 315 N2MA 75 2.9528 160 6.2992 37 1.4567 216 000 48 600 200 000 45 000 5 300 7 500 3.90 8.60
QJ 316 N2MA 80 3.1496 170 6.6929 39 1.5354 232 000 52 200 228 000 51 300 5 000 7 000 4.60 10.10
QJ 317 N2MA 85 3.3465 180 7.0866 41 1.6142 250 000 56 200 255 000 57 300 4 800 6 700 5.45 12.00

QJ 318 N2MA 90 3.5433 190 7.4803 43 1.6929 285 000 64 100 305 000 68 600 4 500 6 300 6.45 14.20
QJ 319 N2MA 95 3.7402 200 7.8740 45 1.7717 305 000 68 600 340 000 76 400 4 300 6 000 7.45 16.40
QJ 320 N2MA 100 3.9370 215 8.4646 47 1.8504 345 000 77 600 400 000 89 900 4 000 5 600 9.30 20.50

QJ 322 N2MA 110 4.3307 240 9.4488 50 1.9685 390 000 87 700 480 000 107 900 3 600 4 800 12.50 27.60
QJ 324 N2MA 120 4.7244 260 10.2362 55 2.1654 415 000 93 300 530 000 119 100 3 200 4 500 16.00 35.30
QJ 326 N2MA 130 5.1181 280 11.0236 58 2.2835 455 000 102 300 610 000 137 100 3 000 4 000 19.50 43.00

QJ 328 N2MA 140 5.5118 300 11.8110 62 2.4409 500 000 112 400 695 000 156 200 2 800 3 800 24.00 52.90
QJ 330 N2MA 150 5.9055 320 12.5984 65 2.5591 530 000 119 100 765 000 172 000 2 600 3 600 29.00 63.90
QJ 332 N2MA 160 6.2992 340 13.3858 68 2.6772 570 000 128 100 880 000 197 800 2 400 3 400 34.50 76.10

QJ 334 N2MA 170 6.6929 360 14.1732 72 2.8346 655 000 147 200 1 040 000 233 800 2 200 3 200 41.50 91.50
QJ 336 N2MA 180 7.0866 380 14.9606 75 2.9528 680 000 152 900 1 020 000 229 300 2 200 3 000 47.50 104.70
QJ 338 N2MA 190 7.4803 400 15.7480 78 3.0709 702 000 157 800 1 116 000 250 900 1 700 2 800 49.00 108.00

QJ 344 N2/309829 220 8.6614 460 18.1102 88 3.4646 904 000 203 200 1 660 000 373 200 1 500 2 400 78.00 172.00
QJ 344 N2MA 220 8.6614 460 18.1102 88 3.4646 780 000 175 300 1 400 000 314 700 1 500 2 400 78.00 172.00

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

66
 Single row
B
Four-point ACBB
Standard
Series: QJ 1017 N2MA — QJ 1988 N2MA
Size: 85 mm — 440 mm
3.3465 in — 17.3228 in

D d

"N2" Design
N2 Design

Designation Principal dimensions Basic load ratings Speed rating Mass

Bore Outside diameter Width Dynamic Static Reference Limiting

d D B C C0 speed speed
mm in mm in mm in N lbf N lbf r/min r/min kg lb

QJ 1017 N2MA 85 3.3465 130 5.1181 22 0.8661 85 200 19 200 102 000 22 900 5 000 8 000 1.10 2.40
QJ 1021 N2MA 105 4.1339 160 6.2992 26 1.0236 124 000 27 900 156 000 35 100 4 000 6 700 2.00 4.40
QJ 1022 N2MA 110 4.3307 170 6.6929 28 1.1024 146 000 32 800 186 000 41 800 3 800 6 300 2.50 5.50

QJ 1030 N2MA 150 5.9055 225 8.8583 35 1.3780 216 000 48 600 305 000 68 600 2 800 4 500 5.25 11.57
QJ 1032 N2MA 160 6.2992 240 9.4488 38 1.4961 247 000 55 500 355 000 79 800 2 600 4 300 6.45 14.20
QJ 1038 N2MA 190 7.4803 290 11.4173 46 1.8110 338 000 76 000 510 000 114 600 2 200 3 400 11.50 25.40

QJ 1040 N2MA 200 7.8740 310 12.2047 51 2.0079 390 000 87 700 620 000 139 400 2 000 3 200 15.00 33.10
QJ 1056 N2MA 280 11.0236 420 16.5354 65 2.5591 553 000 124 300 1 060 000 238 300 1 400 2 400 33.50 73.90
QJ 1060 MA 300 11.8110 460 18.1102 74 2.9134 650 000 146 100 1 340 000 301 200 1 300 2 200 47.50 104.70

QJ 1064 MA 320 12.5984 480 18.8976 74 2.9134 715 000 160 700 1 530 000 343 900 1 200 2 000 50.00 110.20
QJ 1068 N2MA 340 13.3858 520 20.4724 82 3.2283 780 000 175 300 1 700 000 382 200 1 100 1 800 67.50 148.80
QJ 1072 N2MA 360 14.1732 540 21.2598 82 3.2283 793 000 178 300 1 800 000 404 600 1 100 1 700 70.50 155.40

QJ 1076 N2MA 380 14.9606 560 22.0472 82 3.2283 819 000 184 100 1 900 000 427 100 1 000 1 700 73.50 162.00
QJ 1080 N2MA 400 15.7480 600 23.6220 90 3.5433 904 000 203 200 2 160 000 485 600 950 1 500 95.50 210.50
QJ 1084 N2MA 420 16.5354 620 24.4094 90 3.5433 923 000 207 500 2 280 000 512 500 900 1 500 99.50 219.40

QJ 1088 N2MA 440 17.3228 650 25.5906 94 3.7008 995 000 223 700 2 500 000 562 000 850 1 400 115.00 253.50
QJ 1092 N2MA 460 18.1102 680 26.7717 100 3.9370 1 040 000 233 800 2 650 000 595 700 800 1 300 130.00 286.60
QJ 1096 N2MA 480 18.8976 700 27.5591 100 3.9370 1 060 000 238 300 2 800 000 629 400 750 1 300 135.00 297.60

QJ 1240 N2MA 200 7.8740 360 14.1732 70 2.7559 520 000 116 900 865 000 194 500 1 800 3 000 32.50 71.70
QJ 1244 N2MA 220 8.6614 400 15.7480 78 3.0709 592 000 133 100 1 020 000 229 300 1 600 2 600 45.50 100.30
QJ 1248 MA/344524 240 9.4488 440 17.3228 85 3.3465 663 000 149 000 1 220 000 274 300 1 500 2 400 61.00 134.50

QJ 1252 MA 260 10.2362 480 18.8976 90 3.5433 741 000 166 600 1 460 000 328 200 1 300 2 200 78.00 172.00
QJ 1256 N2MA 280 11.0236 500 19.6850 90 3.5433 728 000 163 700 1 460 000 328 200 1 300 2 000 82.00 180.80
QJ 1260 N2MA 300 11.8110 540 21.2598 98 3.8583 832 000 187 000 1 760 000 395 600 1 200 1 900 105.00 231.50
QJ 1264 N2MA 320 12.5984 580 22.8346 105 4.1339 923 000 207 500 2 040 000 458 600 1 100 1 700 130.00 286.60
QJ 1268 MA/344524 340 13.3858 620 24.4094 118 4.6457 1 060 000 238 300 2 450 000 550 800 1 000 1 600 165.00 363.80
QJ 1272 N2MA 360 14.1732 650 25.5906 122 4.8031 1 110 000 249 500 2 600 000 584 500 950 1 500 190.00 418.90

QJ 1276 N2MA 380 14.9606 680 26.7717 132 5.1969 1 170 000 263 000 2 850 000 640 700 900 1 400 220.00 485.00
QJ 1280 N2MA 400 15.7480 720 28.3465 140 5.5118 1 300 000 292 200 3 250 000 730 600 800 1 300 265.00 584.20
QJ 1284 N2MA 420 16.5354 760 29.9213 150 5.9055 1 430 000 321 500 3 750 000 843 000 750 1 300 315.00 694.50

QJ 1288 N2MA 440 17.3228 790 31.1024 155 6.1024 1 400 000 314 700 3 750 000 843 000 750 1 200 350.00 771.60
QJ 1292 N2MA 460 18.1102 830 32.6772 165 6.4961 1 530 000 343 900 4 250 000 955 400 700 1 100 415.00 914.90
QJ 1296 N2MA 480 18.8976 870 34.2520 170 6.6929 1 680 000 377 700 4 750 000 1 068 000 670 1 100 470.00 1 036.20

QJ 1984 MA 420 16.5354 560 22.0472 65 2.5591 637 000 143 200 1 600 000 359 700 950 1 600 51.00 112.40
QJ 1988 N2MA 440 17.3228 600 23.6220 74 2.9134 761 000 171 100 1 900 000 427 100 900 1 500 65.00 143.30

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

67
 Angular contact ball bearings
B
Thrust pack
Double row
Four-point ACBB and Single row ACBB
Standard
Series: BA2B 459304 — BA2B 459328
Size: 20 mm — 140 mm
0.7874 in — 5.5118 in d
D

Series: BA2B 459418 — BA2B 459430

Size: 90 mm — 150 mm
3.5433 in — 5.9055 in

BA2B 4593XX
BA2B 4593XX

Designation Principal dimensions Basic load ratings Speed rating Mass

Bore Outside diameter Width Dynamic Static Reference Limiting

d D B C C0 speed speed
mm in mm in mm in N lbf N lbf r/min r/min kg lb

BA2B 459304 20 0.7874 52 2.0472 30 1.1811 30 700 6 900 20 800 4 680 9 000 13 000 0.28 0.62
BA2B 459306 30 1.1811 72 2.8346 38 1.4961 55 900 12 600 42 500 9 550 6 700 9 000 0.68 1.50
BA2B 459307 35 1.3780 80 3.1496 42 1.6535 62 400 14 000 49 000 11 000 6 000 8 000 0.90 2.00

BA2B 459308 40 1.5748 90 3.5433 46 1.8110 79 300 17 800 65 500 14 700 5 300 7 000 1.25 2.75
BA2B 459309 45 1.7717 100 3.9370 50 1.9685 97 500 21 900 81 500 18 300 4 800 6 300 1.70 3.75
BA2B 459310 50 1.9685 110 4.3307 54 2.1260 119 000 26 800 102 000 22 900 4 300 5 600 2.20 4.85

BA2B 459311 55 2.1654 120 4.7244 58 2.2835 138 000 31 000 120 000 27 000 3 800 5 000 2.80 6.15
BA2B 459312 60 2.3622 130 5.1181 62 2.4409 156 000 35 100 140 000 31 500 3 600 4 800 3.50 7.70
BA2B 459313 65 2.5591 140 5.5118 65 2.5984 174 000 39 100 160 000 36 000 3 200 4 300 4.30 9.50

BA2B 459314 70 2.7559 150 5.9055 70 2.7559 195 000 43 800 180 000 40 500 3 000 4 000 5.30 11.50
BA2B 459317 85 3.3465 180 7.0866 82 3.2283 251 000 56 400 265 000 59 600 2 400 3 400 8.90 19.50
BA2B 459318 90 3.5433 190 7.4803 86 3.3858 270 000 60 700 290 000 65 200 2 200 3 200 10.50 23.00

BA2B 459320 100 3.9370 215 8.4646 94 3.7008 325 000 73 100 380 000 85 400 1 900 2 800 15.00 33.00
BA2B 459322 110 4.3307 240 9.4488 100 3.9370 364 000 81 800 450 000 101 000 1 700 2 400 20.00 44.00
BA2B 459326 130 5.1181 280 11.0236 116 4.5669 403 000 90 600 540 000 121 000 1 500 2 000 35.00 77.00

BA2B 459328 140 5.5118 300 11.8110 124 4.8819 449 000 101 000 620 000 139 000 1 400 1 900 43.00 95.00

BA2B 459418 90 3.5433 160 6.2992 60 2.3622 178 000 40 000 193 000 43 400 2 600 3 600 4.60 10.00
BA2B 459420 100 3.9370 180 7.0866 68 2.6772 221 000 49 700 245 000 55 100 2 200 3 200 6.60 14.50
BA2B 459422 110 4.3307 200 7.8740 76 2.9921 260 000 58 500 310 000 69 700 1 900 2 800 9.20 20.50

BA2B 459424 120 4.7244 215 8.4646 80 3.1496 270 000 60 700 325 000 73 100 1 700 2 400 12.20 27.00
BA2B 459428 140 5.5118 250 9.8425 84 3.3071 296 000 66 500 390 000 87 700 1 600 2 200 17.70 39.00
BA2B 459430 150 5.9055 270 10.6299 90 3.5433 319 000 71 700 44 0000 98 900 1 500 2 000 23.00 50.50

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

68
 B Double row, 40° contact angle
Standard
Series: 3308 DNRCBM — 3313 DNRCBM
Size: 40 mm — 65 mm
1.5748 in — 2.5591 in

D d

Designation Principal dimensions Basic load ratings Speed rating Mass

Bore Outside diameter Width Dynamic Static Reference Limiting

d D B C C0 speed speed
mm in mm in mm in N lbf N lbf r/min r/min kg lb

3308 DNRCBM 40 1.5748 90 3.5433 36.5 1.437 49 400 11 100 41 500 9 300 6 700 7 000 1.20 2.60
3309 DNRCBM 45 1.7717 100 3.9370 39.7 1.563 61 800 13 900 52 000 11 700 6 000 6 300 1.50 3.30
3310 DNRCBM 50 1.9685 110 4.3307 44.4 1.748 81 900 18 400 69 500 15 600 5 300 5 600 1.95 4.30

3311 DNRCBM 55 2.1654 120 4.7244 49.2 1.937 95 600 21 500 83 000 18 700 4 800 5 000 2.55 5.60
3313 DNRCBM 65 2.5591 140 5.5118 58.7 2.311 138 000 31 000 122 000 27 400 4 300 4 500 4.00 8.80

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

69
 Angular contact ball bearings
Double row, 30° contact angle
Conrad
B
Open, sealed, shielded and snap ring
Standard and SKF Explorer
Series: 3200 A — 3220 A
Size: 10 mm — 100 mm
0.3937 in — 3.9370 in A-Z A-N
A-Z A-N
D d

A-2Z A-NR
A-Open A-2Z A-NR
A-Open

Designation Principal dimensions Basic load ratings Speed rating Mass

Sealed
Bore Outside diameter Width Dynamic Static Reference Limiting Limiting
d D B C C0 speed speed speed
mm in mm in mm in N lbf N lbf r/min r/min r/min kg lb

3200 A 10 0.3937 30 1.1811 14.0 .5625 7 610 1 700 4 300 1 000 22 000 24 000 17 000 0.05 0.11
3201 A 12 0.4724 32 1.2598 15.9 .6250 10 100 2 300 5 600 1 300 20 000 22 000 15 000 0.06 0.13
3202 A 15 0.5906 35 1.3780 15.9 .6250 11 200 2 500 6 800 1 500 17 000 18 000 14 000 0.07 0.15

3203 A 17 0.6693 40 1.5748 17.5 .6875 14 300 3 200 8 800 2 000 15 000 16 000 12 000 0.10 0.21
3204 A 20 0.7874 47 1.8504 20.6 .8125 20 000 4 500 12 000 2 700 14 000 14 000 10 000 0.16 0.35
3205 A 25 0.9843 52 2.0472 20.6 .8125 21 600 4 900 14 300 3 200 12 000 12 000 8 500 0.19 0.42

3206 A 30 1.1811 62 2.4409 23.8 .9375 30 000 6 700 20 400 4 600 10 000 10 000 7 500 0.29 0.64
3207 A 35 1.3780 72 2.8346 27.0 1.0625 40 000 9 000 28 000 6 300 9 000 9 000 6 300 0.40 0.88
3208 A 40 1.5748 80 3.1496 30.2 1.1875 47 500 10 700 34 000 7 600 8 000 8 000 5 600 0.58 1.28

3209 A 45 1.7717 85 3.3465 30.2 1.1875 51 000 11 500 39 000 8 800 7 500 7 500 5 300 0.64 1.41
3210 A 50 1.9685 90 3.5433 30.2 1.1875 51 000 11 500 39 000 8 800 7 000 7 000 4 800 0.66 1.46
3211 A 55 2.1654 100 3.9370 33.3 1.3125 60 000 13 500 47 500 10 700 6 300 6 300 4 500 1.05 2.31

3212 A 60 2.3622 110 4.3307 36.5 1.4375 73 500 16 500 58 500 13 200 5 600 5 600 4 000 1.40 3.09
3213 A 65 2.5591 120 4.7244 38.1 1.5000 80 600 18 100 73 500 16 500 4 500 4 800 3 600 1.75 3.86
3214 A 70 2.7559 125 4.9213 39.7 1.5625 88 400 19 900 80 000 18 000 4 300 4 500 – 1.90 4.19

3215 A 75 2.9528 130 5.1181 41.3 1.6250 95 600 21 500 88 000 19 800 4 300 4 500 3 200 2.10 4.63
3216 A 80 3.1496 140 5.5118 44.4 1.7500 106 000 23 800 95 000 21 400 4 000 4 300 3 000 2.65 5.84
3217 A 85 3.3465 150 5.9055 49.2 1.9375 124 000 27 900 110 000 24 700 3 600 3 800 – 3.40 7.50

3218 A 90 3.5433 160 6.2992 52.4 2.0625 130 000 29 200 120 000 27 000 3 400 3 600 – 4.15 9.15
3219 A 95 3.7402 170 6.6929 55.6 2.1875 159 000 35 700 146 000 32 800 3 200 3 400 – 5.00 11.02
3220 A 100 3.9370 180 7.0866 60.3 2.3750 178 000 40 000 166 000 37 300 3 000 3 200 – 6.10 13.45

Note: The 5200/5300 series DRACBB have been replaced with the 3200/3300 series designation.
The product design has not changed; therefore, the fit, form and function remain the same.

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

70
 Double row, 30° contact angle
Conrad
B
Open, sealed, shielded and snap ring
Standard and SKF Explorer
Series: 3304 A — 3318 A
Size: 20 mm — 90 mm
A-RS1 A-Z A-N
0.7874 in — 3.5433 in
A-RS1 A-Z A-N
D d

A-2RS1 A-2Z A-NR

A-Open A-2RS1 A-2Z A-NR
A-Open

Designation Principal dimensions Basic load ratings Speed rating Mass

Sealed
Bore Outside diameter Width Dynamic Static Reference Limiting Limiting
d D B C C0 speed speed speed
mm in mm in mm in N lbf N lbf r/min r/min r/min kg lb

3304 A 20 0.7874 52 2.0472 22.2 .8750 23 600 5 300 14 600 3 300 13 000 13 000 9 000 0.20 0.44
3305 A 25 0.9843 62 2.4409 25.4 1.0000 32 000 7 200 20 400 4 600 11 000 11 000 7 500 0.31 0.68
3306 A 30 1.1811 72 2.8346 30.2 1.1875 41 500 9 300 27 500 6 200 9 000 9 000 6 300 0.59 1.30

3307 A 35 1.3780 80 3.1496 34.9 1.3750 52 000 11 700 35 500 8 000 8 500 8 500 6 000 0.71 1.57
3308 A 40 1.5748 90 3.5433 36.5 1.4375 64 000 14 400 44 000 9 900 7 500 7 500 5 000 1.05 2.31
3308 AH 40 1.5748 90 3.5433 36.5 1.4375 64 000 14 400 44 000 9 900 7 500 7 500 – 1.05 2.31

3309 A 45 1.7717 100 3.9370 39.7 1.5625 75 000 16 900 53 000 11 900 6 700 6 700 4 800 1.40 3.09
3309 AH 45 1.7717 100 3.9370 39.7 1.5625 75 000 16 900 53 000 11 900 6 700 6 700 – 1.40 3.09
3310 A 50 1.9685 110 4.3307 44.4 1.7500 90 000 20 200 64 000 14 400 6 000 6 000 4 300 1.95 4.30

3310 AH 50 1.9685 110 4.3307 44.4 1.7500 90 000 20 200 64 000 14 400 6 000 6 000 – 1.95 4.30
3311 A 55 2.1654 120 4.7244 49.2 1.9375 112 000 25 200 81 500 18 300 5 300 5 300 – 2.55 5.62
3311 AH 55 2.1654 120 4.7244 49.2 1.9375 112 000 25 200 81 500 18 300 5 300 5 300 – 2.55 5.62

3312 A 60 2.3622 130 5.1181 54.0 2.1250 127 000 28 500 95 000 21 400 5 000 5 000 – 3.25 7.16
3313 A 65 2.5591 140 5.5118 58.7 2.3125 146 000 32 800 110 000 24 700 4 500 4 500 – 4.10 9.04
3314 A 70 2.7559 150 5.9055 63.5 2.5000 153 000 34 400 125 000 28 100 4 000 4 000 – 5.05 11.13

3315 A 75 2.9528 160 6.2992 68.3 2.6875 176 000 39 600 140 000 31 500 4 000 4 000 – 5.60 12.35
3315 AH 75 2.9528 160 6.2992 68.3 2.6875 176 000 39 600 140 000 31 500 4 000 4 000 – 5.60 12.35
3316 A 80 3.1496 170 6.6929 68.3 2.8675 182 000 40 900 156 000 35 100 3 400 3 600 – 6.80 14.99

3317 A 85 3.3465 180 7.0866 73.0 2.8750 195 000 43 800 176 000 39 600 3 200 3 400 – 8.30 18.30
3318 A 90 3.5433 190 7.4803 73.0 2.8750 195 000 43 800 180 000 40 500 3 000 3 200 – 9.25 20.39

Note: The 5200/5300 series DRACBB have been replaced with the 3200/3300 series designation.
The product design has not changed; therefore, the fit, form and function remain the same.

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

71
 Angular contact ball bearings
Double row, 30° contact angle
Max type B
Open, sealed, shielded and snap ring
Standard
Series: 3205 E — 3218 E
Size: 25 mm — 90 mm
0.9843 in — 3.5433 in E-RS1 E-Z E-N
D d E-RS1 E-Z E-N
Series: 3305 E — 3316 E
Size: 25 mm — 80 mm
0.9843 in — 3.1496 in

E-2RS1 E-2Z
E-NR
E-OPEN E-2RS1 E-2Z E-NR
E-Open

Designation Principal dimensions Basic load ratings Speed rating Mass

Sealed
Bore Outside diameter Width Dynamic Static Reference Limiting Limiting
d D B C C0 speed speed speed
mm in mm in mm in N lbf N lbf r/min r/min r/min kg lb

3205 E 25 0.9843 52 2.0472 20.6 .8125 22 900 5 150 21 200 4 770 11 000 12 000 8 500 0.25 0.55
3206 E 30 1.1811 62 2.4409 23.8 .9375 30 300 6 810 28 000 6 290 9 500 10 000 7 500 0.35 0.80
3207 E 35 1.3780 72 2.8346 27.0 1.0625 39 100 8 790 36 500 8 210 8 000 8 500 6 300 0.54 1.20

3208 E 40 1.5748 80 3.1496 30.2 1.1875 49 500 11 130 49 000 11 020 7 500 8 000 5 600 0.73 1.60
3209 E 45 1.7717 85 3.3465 30.2 1.1875 51 200 11 510 54 000 12 140 6 700 7 000 5 300 0.77 1.70
3210 E 50 1.9685 90 3.5433 30.2 1.1875 53 900 12 120 58 500 13 150 6 300 6 700 4 800 0.82 1.80

3211 E 55 2.1654 100 3.9370 33.3 1.3125 66 000 14 840 76 500 17 200 5 600 6 000 4 500 1.15 2.50
3212 E 60 2.3622 110 4.3307 36.5 1.4375 78 100 17 560 88 000 19 780 5 000 5 300 4 000 1.50 3.30
3213 E 65 2.5591 120 4.7244 38.1 1.5000 88 000 19 780 106 000 23 800 4 800 5 000 3 600 1.95 4.30

3214 E 70 2.7559 125 4.9213 39.7 1.5625 101 000 22 700 125 000 28 100 4 500 4 800 2.15 4.70
3215 E 75 2.9528 130 5.1181 41.3 1.6250 108 000 24 300 137 000 30 800 4 300 4 500 3 200 2.50 5.50
3216 E 80 3.1496 140 5.5118 44.4 1.7500 128 000 28 800 160 000 36 000 4 000 4 000 3 000 3.00 6.60
–
3217 E 85 3.3465 150 5.9055 49.2 1.9375 142 000 31 900 176 000 39 600 3 600 3 800 – 3.70 8.16
3218 E 90 3.5433 160 6.2992 52.4 2.0625 151 000 33 900 193 000 43 400 3 400 3 600 – 4.55 10.00

3305 E 25 0.9843 62 2.4409 25.4 1.0000 34 100 7 670 30 500 6 860 10 000 10 000 7 500 0.39 0.90
3306 E 30 1.1811 72 2.8346 30.2 1.1875 46 800 10 520 43 000 9 670 8 500 9 000 6 300 0.59 1.30
3307 E 35 1.3780 80 3.1496 34.9 1.3750 52 300 11 760 48 000 10 790 7 500 8 000 6 000 0.86 1.90

3308 E 40 1.5748 90 3.5433 36.5 1.4375 67 100 15 080 65 500 14 720 6 700 7 000 5 000 1.15 2.50
3309 E 45 1.7717 100 3.9370 39.7 1.5625 80 900 18 190 80 000 17 980 6 000 6 300 4 800 1.50 3.30
3310 E 50 1.9685 110 4.3307 44.4 1.7500 95 200 21 400 95 000 21 360 5 300 5 600 – 2.00 4.40

3311 E 55 2.1654 120 4.7244 49.2 1.9375 119 000 26 800 122 000 27 400 5 000 5 300 – 2.65 5.80
3312 E 60 2.3622 130 5.1181 54.0 2.1250 134 000 30 100 143 000 32 100 4 500 4 800 – 3.30 7.30
3313 E 65 2.5591 140 5.5118 58.7 2.3125 182 000 40 900 163 000 36 600 4 300 4 500 – 4.20 9.30

3314 E 70 2.7559 150 5.9055 63.5 2.5000 172 000 38 700 186 000 41 800 4 000 4 300 – 5.00 11.00
3315 E 75 2.9528 160 6.2992 68.3 2.6875 187 000 42 000 208 000 46 800 3 600 3 800 – 6.35 14.00
3316 E 80 3.1496 170 6.6929 68.3 2.6875 201 000 45 200 236 000 53 100 3 400 3 600 – 7.25 16.00

Note: The 5200/5300 series DRACBB have been replaced with the 3200/3300 series designation.
The product design has not changed; therefore, the fit, form and function remain the same.

8BSOJOH
5IF
OFX
SFGFSFODF
BOE
MJNJUJOH
TQFFET
BSF
OPU UP
CF
VTFE BT
B
EJSFDU TVCTUJUVUJPO
GPS UIF
QSFWJPVT
PJM
BOE
HSFBTF
TQFFE
SBUJOHT
4FF
QBHF

GPS EFUBJMT

$POTVMU 4,' 64" *OD
QSJPS UP
EFTJHO
DIBOHF
PS PSEFS QMBDFNFOU

72