STRUCTURE QUICK START XPOINTER PRO

Warning
Positive buoyant, hook it with lanyard.
❶ ❶ Pinpoint Tip
❷ Side scan area
❸ Flashlight LED REGISTER YOUR PRODUCTS
❹ Indication LED
❺ Buzzer vent
TO ACTIVE WARRANTY
❷ ❻ Power button Deteknix Xpointer Pro provides a limited warranty
to the original purchaser of its products against all
❼ Mode button
❽ Battery cover Land mode/LM(0~10M underwater) defects in original workmanship and material,
Power on/off (default) under normal use and service, for ONE years from
❾ Anchor loop the date of purchase with the following exceptions:
Press the Power button once to power on. Press
• All warranties void if electronic part opened.
❸ again to power off.
• Batteries are warranted for 90 days.
Power on/off (retune on)
❹ • Cosmetic discoloration of surfaces.
Press the Power button once to power on. Press • Water flooding caused from battery cap seal.
1S to power off. Deteknix will not be liable for any further loss,
damages, or expenses, including incidental or
❺ consequential damages directly or indirectly
arising from the sale or use of this product.
❻ 2

❼
1
DO & DON’T
• Always make sure battery cap tighten before
entering water.
• Always store your detector fully charged.
• Always rinse equipment in fresh water after
every dive.
❽
Dive mode/DM (10~60M, P12 for detail) • Always apply silicone grease after cleaning O-
❾ Hold two buttons for 2sec to enter dive mode. Come ring.
with 5 times red light blink and vibration. Click • Only open battery cap by clean hand.
• Never leave your equipment in the rinse bucket.
mode 3 times quickly to switch back to land mode.
It may be damaged by other equipment.
 SENSITIVITY ALARM PROGRAMING
❹
❸
❷
❶

2.5sec

Change alarm modes. When powered on, LED controlling. While powered on, keep
press Mode button quickly to switch through pressing on Mode button for 2.5 seconds to
the three different alarm modes (Beep, enter LED light control programing. While
Vibration only, Beep and Vibrate) indicator and flashlight both light up, quick
Losing alert. The probe will start to beep at press on mode button to switch from four
certain frequency when no alarm or operating modes(indicator only, flash light only, all off, all
When powered on, keep pressing Mode for 3 minutes. This is to remind the user to on)
button and quickly press power button to power off or to pick up and re-use. Turn on/off tuning function. Under Expert
change sensitivity level from 1~4(highest Power saving feature. The probe will turnoff Mode, quick press power button once to
level) . Each level will sound an extra beep automatically after 3 minutes alarming under activate/de-activate the retune function.
until level 4 which will sound a long beep. losing mode to save battery.
 RETRIEVE LOW BAT. RECHARGING

Low battery
When the probes flash light start
to blink at a certain frequency, it
Pinpointing means it needs recharging. You
can still use it but the sensitivity
will be a little lower.
Retune

$
1

• Move the detector in circle or cross style to

pinpoint.
2

• Retune function. The retuning function is

• We strongly recommend you to use a
designed for ground balance to high
quality wall charger when re-charge the
minimization condition or narrow down the
probe. It will takes about 2~3 hours to
target position. Xpointer family are powered
fully charge
by Pulse Induction technology which will not
• Laptop or desktop computer’s USB port
produce any falsing to saltwater or black Remove battery cap
produce lower power which could make
sand environment. You can use this function Hold and twist the battery cap anti-clockwise to
the recharging longer than wall charger.
to help you get closer to the target. Just loosen it.
• The probe will stop blinking when it is
quick press the power button once to mute Hold and twist clockwise to re-tight.
fully charged. You can leave the USB
the alarm and move again until you hear the Beware of cross threading the cap and body
cable inside the recharge house after
target. You can also turn it off to make the when tightening the cap.
recharging.
operating simple.
 MAINTENANCE O-RING DIVE MODE CONTROL

Cleaning the Device

1.Use tab water or dampen a clean cloth with
a mild detergent solution. 2.Wipe the device
with the damp cloth. 3.Thoroughly dry the
device. Avoid chemical cleaners and
solvents which can damage plastic ❶ ❷ ❸
components. Clean dust sand and fabric if spotted.
Even a tiny grain of sand will cause water Activate alarm: tilt it up side down 3X to activate
ingress. the detection mode(DMA). The detector is ready to
use. The red indication will blink twice every 3
sec. You are ready to search.

keep 5sec~
Mute alarming:Keep the coil up for
5 seconds to turn back to standby
mode (DMS). It will come with 1sec
Apply quality silicone O-ring grease alarm and the sensor is now stop
The device is waterproof to 60M/200FT. It can thoroughly. working. The red indication will
withstand immersion in 60M/200FT of water blink once every 3 sec. The unit is
for 30 minutes. After submersion, be certain still powered on until power off at
to wipe dry and air dry the device before snorkeling mode.
using or charging.
Notice:
• Under deep water when two buttons been
Do not store the device where prolonged
pressed down, the detector will switch to dive
exposure to extreme temperatures can occur
mode automatically.
because it can cause permanent damage. Change O-ring once a year at least. Use • No losing alert and power saving under diving
qualified original part only. mode.