IO-Link Photoelectric Sensor

E3Z-@-IL@
IO-Link Makes Sensor Level Information Visible and
Solves the Three Major Issues at Manufacturing Sites!
Standard Photoelectric Sensor.
• Downtime can be reduced.
• Notifies you of faulty parts and changing conditions
in the Sensor in real time.
• The frequency of sudden failure can be decreased.
• The incident light level monitor prevents false
detection before it happens.
• The efficiency of changeover can be improved.
• The batch check for individual sensor IDs significantly
For the most recent information on models that have been certified for
decreases commissioning time. safety standards, refer to your OMRON website.
• Three types of sensing methods and three types
Be sure to read Safety Precautions
of connection methods are available. on page 9.

Ordering Information
IO-Link Model / Sensors [Refer to Dimensions on page 10.] Red light Infrared light

Model
Sensing method Appearance Connection method Sensing distance Baud rate
PNP
Pre-wired (2 m) E3Z-T81-IL2 2M

Pre-wired M12 connector E3Z-T81-M1TJ-IL2 0.3M

COM2

Standard M8 connector E3Z-T86-IL2

Through-beam
(Emitter + Receiver) 15 m
*3 Pre-wired (2 m) E3Z-T81-IL3 2M

Pre-wired M12 connector E3Z-T81-M1TJ-IL3 0.3M

COM3

Standard M8 connector E3Z-T86-IL3

Pre-wired (2 m) E3Z-R81-IL2 2M
*1 Pre-wired M12 connector *2 COM2 E3Z-R81-M1TJ-IL2 0.3M
Retro-reflective with Standard M8 connector 4m E3Z-R86-IL2
MSR function Pre-wired (2 m) (100 mm) E3Z-R81-IL3 2M
(When using E39-R1S)
Pre-wired M12 connector COM3 E3Z-R81-M1TJ-IL3 0.3M
Standard M8 connector E3Z-R86-IL3
Note: Please contact your OMRON sales representative regarding the IO-Link setup file (IODD file).
*1. The Reflector is sold separately. Select the Reflector model most suited to the application.
*2. The sensing distance specified is possible when the E39-R1S is used. Values in parentheses indicate the minimum required distance between the Sensor and Reflector.
*3. Through-beam Sensors are sold in sets that include both the Emitter and Receiver.

1
 E3Z-@-IL@

Red light Infrared light

Model
Sensing method Appearance Connection method Sensing distance Baud rate
PNP
Pre-wired (2 m) E3Z-D82-IL2 2M
Pre-wired M12 connector COM2 E3Z-D82-M1TJ-IL2 0.3M
Standard M8 connector E3Z-D87-IL2
1m
Pre-wired (2 m) E3Z-D82-IL3 2M
Pre-wired M12 connector COM3 E3Z-D82-M1TJ-IL3 0.3M
Standard M8 connector E3Z-D87-IL3
Diffuse-reflective
Pre-wired (2 m) E3Z-L81-IL2 2M
Pre-wired M12 connector COM2 E3Z-L81-M1TJ-IL2 0.3M
Standard M8 connector E3Z-L86-IL2
90 mm
Pre-wired (2 m) (narrow beam) E3Z-L81-IL3 2M
Pre-wired M12 connector COM3 E3Z-L81-M1TJ-IL3 0.3M
Standard M8 connector E3Z-L86-IL3
Note: Please contact your OMRON sales representative regarding the IO-Link setup file (IODD file).

Accessories (Sold Separately)

Slit (A Slit is not provided with Through-beam Sensors) Order a Slit separately if required.
Sensing distance Minimum detectable object
Slit width Model Contents
E3Z-T@@ (Reference value)
0.5-mm dia. 50 mm 0.2-mm dia. E39-S65A
1-mm dia. 200 mm 0.4-mm dia. E39-S65B
2-mm dia. 800 mm 0.7-mm dia. E39-S65C One set
(contains Slits for both the
0.5 × 10 mm 1m 0.2-mm dia. E39-S65D Emitter and Receiver)
1 × 10 mm 2.2 m 0.5-mm dia. E39-S65E
2 × 10 mm 5m 0.8-mm dia. E39-S65F

Reflectors (Reflector required for Retroreflective Sensors) A Reflector is not provided with the Sensor. Be sure to order a Reflector separately.
Sensing distance *
Name E3Z-R Model Quantity Remarks
Rated value Reference value
3 m (100 mm) --- E39-R1 1
4 m (100 mm) --- E39-R1S 1
Reflector --- 5 m (100 mm) E39-R2 1 • Reflectors are not
--- 2.5 m (100 mm) E39-R9 1 provided with
Retro-reflective
--- 3.5 m(100 mm) E39-R10 1
models.
Fog Preventive Coating --- 3 m (100 mm) E39-R1K 1
• The MSR function of
Small Reflector --- 1.5 m (50 mm) E39-R3 1 the E3Z-R@ is
--- 700 mm (150 mm) E39-RS1 1 enabled.
Tape Reflector --- 1.1 m (150 mm) E39-RS2 1
--- 1.4 m (150 mm) E39-RS3 1
Note:1. If you use the Reflector at any distance other than the rated distance, make sure that the stability indicator lights properly when you install the Sensor.
2. Refer to Reflectors on E39-L/E39-S/E39-R on your OMRON website for details.
* Values in parenthese indicate the minimum required distance between the Sensor and Reflector.

2
 E3Z-@-IL@

Mounting Brackets A Mounting Bracket is not enclosed with the Sensor. Order a Mounting Bracket separately if required.
Appearance Model (material) Quantity Remarks Appearance Model (material) Quantity Remarks

E39-L153 E39-L98 Metal Protective Cover

1 1
(SUS304) *1 (SUS304) *2 Bracket

Mounting Brackets

E39-L104 E39-L150
1 1
(SUS304) *1 (SUS304)
(Sensor adjuster)

Easily mounted to the

aluminum frame rails of
E39-L43 Horizontal Mounting conveyors and easily
1
(SUS304) *2 Brackets adjusted.
E39-L151
1 For left to right adjust-
(SUS304)
ment
E39-L142 Horizontal Protective
1
(SUS304) *2 Cover Bracket

E39-L44 E39-L144 Compact Protective

1 Rear Mounting Bracket 1 Cover Bracket (For E3Z
(SUS304) (SUS304) *2
only)

Note:1. When using Through-beam models, order one bracket for the Receiver and one for the Emitter.
2. Refer to Mounting Brackets on E39-L/E39-S/E39-R on your OMRON website for details.
*1. Cannot be used for Standard Connector models with mounting surface on the bottom. In that case, use Pre-wired Connector models.
*2. Cannot be used for Standard Connector models.

Sensor I/O Connectors

(Models for Connectors and Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)
Size Type Appearance Cable length Model
Smartclick connector 2m XS5F-D421-D80-F
Straight *2
5m XS5F-D421-G80-F
Socket on one cable
end Smartclick connector 2m XS5F-D422-D80-F
L-shape *2 *3
5m XS5F-D422-G80-F
M12
Smartclick connector 2m XS5W-D421-D81-F
Straight/
Straight *2 5m XS5W-D421-G81-F
Socket and plug on
cable ends *1 Smartclick connector 2m XS5W-D422-D81-F
L-shape/L-shape *2 *3
5m XS5W-D422-G81-F

2m XS3F-M421-402-A
Straight *3
5m XS3F-M421-405-A
M8 Socket on one cable
end
2m XS3F-M422-402-A
L-shape *3 *4
5m XS3F-M422-405-A

M8-M12 (Smartclick)
M8 socket/ Socket and plug on conversion cable *2 0.2 m XS3W-M42C-4C2-A
M12 plug cable ends

Note:1. When using Through-beam models, order one connector for the Receiver and one for the Emitter.
2. Refer to Sensor I/O Connectors/Sensor Controllers on your OMRON website for details.
*1. Straight type/L-shape type combinations are also available.
*2. The connectors will not rotate after they are connected.
*3. The cable is fixed at an angle of 180° from the sensor emitter/receiver surface.

3
 E3Z-@-IL@
Ratings and Specifications
IO-Link Model
Retro-reflective
Sensing method Through-beam Diffuse-reflective Narrow-beam Models
with MSR function
Pre-wired E3Z-T81-IL@ E3Z-R81-IL@ E3Z-D82-IL@ E3Z-L81-IL@
PNP Pre-wired
Model E3Z-T81-M1TJ-IL@ E3Z-R81-M1TJ-IL@ E3Z-D82-M1TJ-IL@ E3Z-L81-M1TJ-IL@
output connector (M12)
Item Connector (M8) E3Z-T86-IL@ E3Z-R86-IL@ E3Z-D87-IL@ E3Z-L86-IL@
4 m (100 mm) *
1m 90 + 30 mm
(when using E39-R1S)
Sensing distance 15 m (white paper: 300 × (white paper: 100 ×
3 m (100 mm) *
300 mm) 100 mm)
(when using E39-R1)
2.5 dia. and sensing dis-
Spot diameter (reference value) ---
tance of 90 mm
Standard sensing object Opaque: 12-mm dia. min. Opaque: 75-mm dia. min. ---
Minimum detectable object
--- 0.1 mm (copper wire)
(reference value)
Differential travel Refer to Engineering
--- --- 20% max. of setting distance
(representative example) data on page 6
Both emitter and
Directional angle 2 to 10° ---
receiver: 3 to 15°
Light source (wavelength) Infrared LED (870 nm) Red LED (660 nm) Infrared LED (860 nm) Red LED (650 nm)
Power supply voltage 10 to 30 VDC (including 10% ripple (p-p))
50 mA max. (Emitter:
Current consumption 25 mA max., Receiver: 30 mA max.
25 mA max.)
Load power supply voltage: 30 VDC max., Load current: 100 mA max.
Residual voltage: Load current of less than 10 mA: 1 V max.
Control output Load current of 10 to 100 mA: 2 V max.
PNP open collector output
Light-ON/Dark-ON selectable
In the Standard I/O mode (SIO mode): Operation indicator (orange, lit) and stability indicator (green, lit)
Indicators
In the IO-Link Mode: Operation indicator (orange, lit) and communication indicator (green, blinking at 1 s intervals)
Reversed power supply
polarity protection, out-
Reversed power supply polarity protection, output short-circuit protection,
Protection circuits put short-circuit protec-
reversed output polarity protection, and mutual interference prevention
tion, and reversed output
polarity protection
Response time Operate or reset: 1 ms max.
Sensitivity adjustment Sensitivity adjuster / IO-Link communications
Ambient illumination Incandescent lamp: 3,000 lx max.
(Receiver side) Sunlight: 10,000 lx max.
Operating: −25 to 55°C (with no icing or condensation)
Ambient temperature range
Storage: −40 to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP67
Pre-wired cable (standard cable length 2 m), M12 pre-wired connector (standard cable length 0.3 m),
Connection method
M8 connector
Weight Pre-wired cable (2 m) Approx. 120 g Approx. 65 g
(packed Pre-wired connector (M12) Approx. 60 g Approx. 30 g
state) Connector (M8) Approx. 30 g Approx. 20 g
Case Polybutylene terephthalate (PBT)
Material Display Modified polyarylate
Lens Modified polyarylate Methacrylate resin (PMMA) Modified polyarylate
Operation mode switching between Light ON and Dark ON, setup of the instability detection level for light
receiving and non-light receiving, timer function of the control output and timer time selecting, instability
Main IO-Link functions
output (IO-Link mode) ON delay timer time selecting, setup of a teaching level and execution of teaching,
setup of light receiving sensitivity level, monitor output, operating hours read-out, and initial reset
IO-Link
Ver 1.1
specification
Communication Baud rate -IL3: COM3 (230.4 kbps), -IL2: COM2 (38.4 kbps)
specifications Data length PD size: 2 bytes, OD size: 1 byte (M-sequence type: TYPE_2_2)
Minimum cycle
-IL3 (COM3): 1 ms, -IL2 (COM2): 2.3 ms
time
Accessories Instruction manual (Neither Reflectors nor Mounting Brackets are provided with any of the above models.)
* Values in parentheses indicate the minimum required distance between the Sensor and Reflector.

4
 E3Z-@-IL@
Engineering Data (Reference Value)
Parallel Operating Range
Through-beam Models Through-beam Models Retro-reflective Models
E3Z-T8@-IL@ E3Z-T8@-IL@ and Slit E3Z-R8@-IL@ and Reflector
(A Slit is mounted to the Emitter and
Receiver.)

Distance Y (mm)
Distance Y (mm)

Distance Y (mm)
1000 250 200
E39-R1K E39-R10
Y
800 200 Y
150
E39-R3 X
600 150 X
100
400 100
50
200 50
Distance X (m)
0 0 0
10 20 30 40 1 2 3 4 5 2 4 6 8
−200
Distance −50
Distance
X (m) X (m) −50
−400 −100 E39-S65B

E39-S65C −100
−600 −150
Y E39-S65D
−150 E39-R9
−800 −200 E39-S65E E39-R2
X E39-S65F E39-R1 E39-R1S
−1000 −250 −200

Operating Range
Diffuse-reflective Models Narrow-beam Reflective Models
E3Z-D8@-IL@ E3Z-L8@-IL@
Distance Y (mm)
Distance Y (mm)

80 10 Sensing object: 100 × 100 mm white paper

Sensing object: 300 × 300 mm white paper
8
60 Y Y
6
40
X X
4
20
2

0 0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 50 100 150 250
200 Distance
Distance −2
−20 X (m) X (mm)
−4
−40
−6
−60
−8

−80 −10

Monitor Output vs. Sensing Distance

Through-beam Models Retro-reflective Models
E3Z-T8@-IL@ E3Z-R8@-IL@ and E39-R1 Reflector
Monitor Output

Monitor Output

280 280
260 260
240 240 Sensitivity adjuster:
MAX
220 Sensitivity adjuster: MAX 220
200 200
180 180
Sensitivity adjuster: 1/2 Sensitivity
160 160
adjuster: 1/2
140 140
120 120
100 100
80 80
Sensitivity
60 60 adjuster: 1/3
Sensitivity
40 adjuster: 1/3 40
20 20

0 5 10 15 20 25 30 35 40 45 50 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Distance (m) Distance (m)

5
 E3Z-@-IL@

Monitor Output vs. Sensing Distance

Diffuse-reflective Models Narrow-beam Reflective Models
E3Z-D8@-IL@ E3Z-L8@-IL@

Monitor Output
280
Monitor Output

280
260 260

240 240
Sensitivity adjuster: MAX
220 Sensitivity adjuster: MAX 220

200 200

180 180
Sensitivity adjuster: 1/2
Sensitivity adjuster: 1/2 160
160
140 140

120 120

100 100

80 80

60 60

40 40
Sensitivity Sensitivity
20 20 adjuster: 1/3
adjuster: 1/3
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0 50 100 150 200 250 300 350

Distance (m) Distance (mm)

Sensing Object Size vs. Sensing Distance

Diffuse-reflective Models Narrow-beam Reflective Models
E3Z-D8@-IL@ E3Z-L8@-IL@
Distance (mm)

4.5 300
Distance (m)

d d
4
d 250
SUS d
3.5 White paper
(glossy surface)

3 200

2.5
150
2

1.5 100
White paper
1
50
0.5 Black paper

0 50 100 150 200 250 300 350 0 1 2 3 5 7.5 10 20 30 100

Side length (one side) of Side length (one side) of
sensing object: d (mm) sensing object: d (mm)

Spot Diameter vs. Sensing Distance Differential Travel vs. Sensing Distance
Narrow-beam Reflective Models Narrow-beam Reflective Models
E3Z-L8@-IL@ E3Z-L8@-IL@
Differential travel (mm)
Spot diameter (mm)

4.0 30

3.5
25

3.0
20
2.5

2.0 15

1.5
10

1.0
5
0.5

0 20 40 60 80 100 120 140 160 0 50 75 100 125 150

Distance (mm) Distance (mm)

6
 E3Z-@-IL@
I/O Circuit Diagrams

Stable Unstable Stable

operation operation operation
Opera- zone zone zone
Output
tion
mode
mode
*1

ON Stability indicator
OFF (green) *5
ON Operation indicator
OFF (orange)
L ON
ON
Control output 1 *2
OFF *1. The operation mode can be changed by the IO-Link communications.
Standard ON *2. The timer function can be set up using the IO-Link communications
Control output 2 *2
I/O OFF for control output 1 and 2 separately. (It is able to select ON delay,
mode OFF delay, or one-shot function and select a timer time of 1 to 4000
(SIO ON Stability indicator ms (T).)
mode) OFF (green) *5
*3. In the IO-Link mode, if the ON/OFF speed of the sensor is slow, high-
ON Operation indicator speed response of 1 ms or less can be realized using control output
OFF (orange)
D ON 2 as a sensor.
ON *4. The judgment time for the instability detection diagnosis can be
Control output 1 *2
OFF selected using the IO-Link communications. (For the ON delay timer
ON function to detect instability, the setting can be selected from 0
Control output 2 *2
OFF (invalid), 10, 50, 100, 300, 500, or 1000 ms.
*5. The judgment condition for the light receiving/non-light receiving
instability detection function can be selected using the IO-Link
Timing Flashing Communication communications. (Setting of light receiving instability detection
(1 s cycle) indicator (green)
Chart threshold: 500%/400%/300%/200%/140%, setting of non-light
ON Operation indicator receiving instability detection threshold: 70%/50%)
OFF (orange)
1 Control output 1 Present
0 (Byte1_bit0) *2 Sensing
Not
L ON Control output 2 objectpresent T
ON
*2 *3 ON 1
OFF Instability detection ON-delay L ON
1 (Light receiving) OFF 0 T
0 (Byte1_bit4) *4*5 ON 1
D ON
1 Instability detection OFF 0
0 (Non-light receiving)
(Byte1_bit3)*4*5
IO-Link Present
Sensing
Not
mode objectpresent T
Flashing Communication ON 1
(1 s cycle) display lamp (green) OFF-delay L ON
OFF 0 T
ON Operation display ON 1
OFF lamp (orange) D ON
Control output 1 OFF 0
1
0 (Byte1_bit0) *2
D ON Control output 2 Present
ON Sensing
Not
OFF *2 *3 object
Instability detection present T
1 (Light receiving) ON 1
0 (Byte1_bit4) *4*5 One shot L ON
OFF 0 T
1 Instability detection ON 1
0 (Non-light receiving) D ON
(Byte1_bit3)*4*5 OFF 0

Note: Please contact your OMRON sales representative regarding

assignment of data.

Reflective / Receiver of Through-beam Model

E3Z-@8@-IL@
When using as a general When using the Sensor connected Connector Pin Arrangement
sensor to IO-Link Master Unit Pre-wired M12 connector Standard M8 connector
Brown L+ 10 to 30VDC Brown L+ L+ E3Z-@81-M1TJ-IL@ E3Z-@86-IL@
1 1
E3Z-@82-M1TJ-IL@ E3Z-@87-IL@
E3Z-T81-D-M1TJ-IL@ E3Z-T86-D-IL@
Black C/Q Black C/Q C/Q
4 4
1 2 4
2 4 1 3
White DO Load White DO DI 3
2 2

Load
Blue L- Blue L- L-
3 3
0V
Photoelectric Photoelectric IO-Link
Output Sensor Sensor master

circuit
Emitter of Through-beam Model
E3Z-T8@-L-IL@
When using as a general When using the Sensor connected
sensor to IO-Link Master Unit
Brown L+ 10 to 30VDC Brown L+ L+
1 1 Connector Pin Arrangement
E3Z-T81-L-M1TJ-IL□ E3Z-T86-L-IL□

1 2 4
Black C/Q Black C/Q C/Q
4 4 2 4 1 3
3

Note: Pins 2 is not used. Note: Pins 2 is not used.

Blue L- Blue L- L-
3 3
0V
Photoelectric Photoelectric IO-Link
Sensor Sensor master

7
 E3Z-@-IL@

Plugs (Sensor I/O Connectors)

M8 connector Through-beam Models (Emitter)
Wire color
Pin arrangement
2 Classifi- Wire Connector
4 1 Brown Application
2 White cation color pin No.
3 1
3 Blue Brown 1 Power supply (+V)
4 Black
White 2 −
DC
Blue 3 Power supply (0 V)
XS3F-M421-402-A
XS3F-M421-405-A Black 4 Output C/Q
XS3F-M422-402-A
XS3F-M422-405-A Note: Pins 2 is not used.

M12 connector
Wire color
2 1 Brown
1 3
2 White
3 Blue
4 4 Black
Through-beam Models (Receiver)
XS5F-D421-D80-F
XS5F-D421-G80-F
Retro-reflective Models
XS5F-D422-D80-F Diffuse-reflective Models
XS5F-D422-G80-F
Pin arrangement
M8-M12 (Smartclick) conversion cable Classifi- Wire Connector Application
cation color pin No.
Terminal No. Wire color Brown 1 Power supply (+V)

1
White 2 Output DO
4 2 1 1 Brown DC
2 2 White 2 4
Blue 3 Power supply (0 V)
3 1
3 3 Blue
4 4 Black 3
Black 4 Output C/Q

XS3W-M42C-4C2-A

Nomenclature
Through-beam Models
E3Z-T8@-IL@ (Receiver)
Retro-reflective Models
In the Standard I/O mode (SIO mode): Operation indicator
E3Z-R8@-IL@
Stability indicator (green) (orange)
In the IO-Link mode: Sensitivity adjuster
Diffuse-reflective Models IO-Link communication indicator (green)
E3Z-D8@-IL@
Operation selector
E3Z-L8@-IL@

8
 E3Z-@-IL@
Safety Precautions
Be sure to read the precautions for all models in the website at: www.omron247.com.
Warning Indications Precautions for Safe Use
Warning level
Indicates a potentially hazardous situation which,
Be sure to follow the safety precautions below for added safety.
WARNING if not avoided, will result in minor or moderate injury, 1. Do not use the sensor under the environment with explosive or
or may result in serious injury or death. Additionally ignition gas.
there may be significant property damage. 2. Never disassemble, repair nor tamper with the product.
Precautions Supplementary comments on what to do or avoid
for Safe Use doing, to use the product safely. Precautions for Correct Use
Precautions Supplementary comments on what to do or avoid 1. Do not use the product under the following conditions.
doing, to prevent failure to operate, malfunction or (1) In the place exposed to the direct sunlight.
for Correct Use undesirable effect on product performance. (2) In the place where humidity is high and condensation may
occur.
Meaning of Product Safety Symbols (3) In the place where vibration or shock is directly transmitted to
the product.
General prohibition 2. Connection and Mounting
Indicates the instructions of unspecified prohibited (1) If the sensor wiring is placed in the same conduits or ducts as
action. high-voltage or high-power lines, inductive noise may cause
malfunction or damage. Wire the cables separately or use a
Caution, explosion shielded cable.
Indicates the possibility of explosion under specific (2) Use an extension cable less than 100 m long for Standard I/O
conditions. mode and less than 20 m for IO-Link mode.
(3) Do not exceed the following force values applied to the cable.
Caution, fire Tensile: 80 N max., torque: 0.1 Nm max., pressure: 20 N max.,
Indicates the possibility of fires under specific flexure: 3 kg max.
conditions. M8 metal connectors
(4) Fasten a fixed implement by hand. If you use pliers, it may
WARNING cause malfunction or damage to it.
3. Cleaning
This product is not designed or rated for ensuring Do not use thinner, alcohol, or other organic solvents. Otherwise,
safety of persons either directly or indirectly. the optical properties and degree of protection may be degraded.
Do not use it for such purposes. 4. Power supply
When using a commercially available switching regulator, be sure
to ground the FG (Frame Ground) terminals.
The maximum power supply voltage is 30 VDC. 5. Power supply reset time
Before turning the power ON, make sure that the The photoelectric switch will begin sensing no later than 100 ms
power supply voltage does not exceed the maximum after the power is turned on. If the load and the photoelectric
voltage. switch is connected to different power supply, the photoelectric
switch must be always turned on first.
Never use the product with an AC power supply. 6. Turning off the power supply
Otherwise, explosion may result. When turning off the power, output pulse may be generated. We
recommend turning off the power supply of the load or load line
first.
7. Water resistance
Do not use the product with voltage in excess of the Though this is type IP67, do not use in the water, rain or outdoors.
rated voltage. 8. Please process it as industrial waste.
Excess voltage may result in malfunction or fire.

Do not use the product above rated load.

9
 E3Z-@-IL@
(Unit: mm)
Dimensions Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.

Sensors
Through-beam Models * 12

Pre-wired Models
E3Z-T81-IL@ Emitter
Power indicator/
IO-Link communication
10.8 indicator (green)
2.1 7.2 20
2.8 3
Lens
Terminal Specifi-
No. cations
12.7
1 +V
31 11 25.4
2 ---
3 0V
Two, M3
4 Output C/Q
Pins 2 is not used. Pre-wired M12 connector
4 dia. vinyl-insulated round cable with 3 conductors (E3Z-T@@-M1TJ)
(Conductor cross section: 0.2 mm2 (AWG24),
Insulator diameter: 1.1 mm), Standard length: 2 m 4 dia. vinyl-insulated round cable
Standard length: 0.3 m
11.2 4.5
2 1
Operation Indicator (orange) 7.5

Receiver
M12×1 3 4
Operation selector
Stability indicator/
10.8 IO-Link communication Sensitivity adjuster
indicator (green)
2.1 7.2 20
2.8 3
Lens
Terminal Specifi-
12.7 No. cations
31 11 25.4 1 +V
2 Output DO
3 0V
Two, M3
4 Output C/Q
4 dia. vinyl-insulated round cable with 4 conductors
(Conductor cross section: 0.2 mm2 (AWG24),
Insulator diameter: 1.1 mm), Standard length: 2 m

Through-beam Models * 12

Connector Models
E3Z-T86-IL@ Emitter
Power indicator/
10.8 IO-Link communication
indicator (green)
2.1 7.2 20
2.8 3
Lens
Terminal Specifi-
No. cations
12.7
1 +V
31 11 25.4
2 ---
3 0V
4 Output C/Q
10.4 Two, M3
M8 connector Pins 2 is not used.

9.75

11.2 4.5
Operation Indicator (orange) 7.5 Operation
selector

Receiver
Stability indicator/ Sensitivity
10.8 IO-Link communication adjuster
indicator (green)
2.1 7.2 20
2.8 3
Lens Terminal Specifi-
No. cations
12.7 1 +V
31 11 25.4 2 Output DO
3 0V
4 Output C/Q
Two, M3
10.4
M8 connector

9.75

* Models numbers for Through-beam Sensors (E3Z-T@@) are for sets that include both the Emitter and Receiver.
The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3Z-T81-IL@-L 2M), the model number of the Receiver, by adding
"-D" (example: E3Z-T81-IL@-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers.

10
 E3Z-@-IL@

Retro-reflective Models
Pre-wired Models
11.2 4.5
E3Z-R81-IL@
Operation Indicator (orange) 7.5
E3Z-D82-IL@
E3Z-L81-IL@

Operation selector
Power indicator/
IO-Link communication Sensitivity adjuster
indicator (green)
Pre-wired M12 connector
10.8
2.1 20 (E3Z-@8@-M1TJ)
2.8 3
Receiver
Lens 7 dia. 4 dia. vinyl-insulated round cable
Standard length: 0.3 m

16.7 2 1
31 8 25.4

M12×1 3 4
Two, M3
Emitter
Lens 7 dia.
4 dia. vinyl-insulated round cable with 4 Terminal Specifi-
conductors (Conductor cross section: No. cations
0.2 mm2 (AWG24), Insulator diameter: 1.1 mm),
Standard length: 2 m 1 +V
2 Output DO
3 0V
4 Output C/Q

Retro-reflective Models
Connector Models 11.2 4.5

E3Z-R86-IL@ Operation Indicator (orange) 7.5

E3Z-D87-IL@
E3Z-L86-IL@
Operation selector
Stability indicator/ Sensitivity adjuster
IO-Link communication
indicator (green)
10.8
2.1 20
2.8 3
Receiver
Lens 7 dia.

16.7
31 8 25.4

Emitter
Lens 7 dia.
10.4 Two, M3
M8 connector

9.75
Terminal Specifi-
No. cations
1 +V
2 Output DO
3 0V
4 Output C/Q

Note: The lens for the E3Z-D@2/D@7 is black.

11
 E3Z-@-IL@

Accessories (Order Separately)

Slits Slits
E39-S65A E39-S65D 10.4
E39-S65B 10.4 E39-S65E A
20.2
20.2
E39-S65C E39-S65F
A

12.7 12.7
32.2 32.2 10

0.2-mm-thick 0.2-mm-thick

Model Size A Material Model Size A Material

E39-S65A 0.5 dia. SUS301 E39-S65D 0.5 SUS301
E39-S65B 1.0 dia. stainless E39-S65E 1.0 stainless
E39-S65C 2.0 dia. steel E39-S65F 2.0 steel

Mounting Bracket Mounting Bracket

E39-L44 (Mounting dimensions)
E39-L104 1
(Mounting dimensions)

7.0
14°
19.5 R20 6.7
14.1 26.2
3 6 4.5
8.7 17.8
23.2 29
12.4

18 36 39
20°
1.8 21.5
8.8

10°
26.6
16.2 3 31.2
27

Reflectors
Refer to E39-R on your OMRON website for details.
Sensor I/O Connectors
Refer to XS3 or XS5 on your OMRON website for details.

12
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
part of all quotes, agreements, purchase orders, acknowledgments, price lists, BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
catalogs, manuals, brochures and other documents, whether electronic or in PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
writing, relating to the sale of products or services (collectively, the "Products") INTENDED USE. Omron further disclaims all warranties and responsibility of
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron any type for claims or expenses based on infringement by the Products or oth-
objects to any terms or conditions proposed in Buyer’s purchase order or other erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-
documents which are inconsistent with, or in addition to, these Terms. gation hereunder shall be, at Omron’s election, to (i) replace (in the form
2. Prices; Payment Terms. All prices stated are current, subject to change with- originally shipped with Buyer responsible for labor charges for removal or
out notice by Omron. Omron reserves the right to increase or decrease prices replacement thereof) the non-complying Product, (ii) repair the non-complying
on any unshipped portions of outstanding orders. Payments for Products are Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
due net 30 days unless otherwise stated in the invoice. the non-complying Product; provided that in no event shall Omron be responsi-
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices ble for warranty, repair, indemnity or any other claims or expenses regarding
sent to Buyer after deducting transportation charges, taxes and duties, and will the Products unless Omron’s analysis confirms that the Products were prop-
be allowed only if (i) the invoice is paid according to Omron’s payment terms erly handled, stored, installed and maintained and not subject to contamina-
and (ii) Buyer has no past due amounts. tion, abuse, misuse or inappropriate modification. Return of any Products by
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or Buyer must be approved in writing by Omron before shipment. Omron Compa-
the maximum legal rate, whichever is less, on any balance not paid within the nies shall not be liable for the suitability or unsuitability or the results from the
stated terms. use of Products in combination with any electrical or electronic components,
5. Orders. Omron will accept no order less than $200 net billing. circuits, system assemblies or any other materials or substances or environ-
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all ments. Any advice, recommendations or information given orally or in writing,
costs involved in, obtaining any government approvals required for the impor- are not to be construed as an amendment or addition to the above warranty.
tation or sale of the Products. See http://www.omron247.com or contact your Omron representative for pub-
7. Taxes. All taxes, duties and other governmental charges (other than general lished information.
real property and income taxes), including any interest or penalties thereon, 14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
imposed directly or indirectly on Omron or required to be collected directly or FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
indirectly by Omron for the manufacture, production, sale, delivery, importa- LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
tion, consumption or use of the Products sold hereunder (including customs WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
duties and sales, excise, use, turnover and license taxes) shall be charged to BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
and remitted by Buyer to Omron. Further, in no event shall liability of Omron Companies exceed the individual
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory price of the Product on which liability is asserted.
to Omron, Omron reserves the right to stop shipments or require satisfactory 15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
security or payment in advance. If Buyer fails to make payment or otherwise their employees from and against all liabilities, losses, claims, costs and
comply with these Terms or any related agreement, Omron may (without liabil- expenses (including attorney's fees and expenses) related to any claim, inves-
ity and in addition to other remedies) cancel any unshipped portion of Prod- tigation, litigation or proceeding (whether or not Omron is a party) which arises
ucts sold hereunder and stop any Products in transit until Buyer pays all or is alleged to arise from Buyer's acts or omissions under these Terms or in
amounts, including amounts payable hereunder, whether or not then due, any way with respect to the Products. Without limiting the foregoing, Buyer (at
which are owing to it by Buyer. Buyer shall in any event remain liable for all its own expense) shall indemnify and hold harmless Omron and defend or set-
unpaid accounts. tle any action brought against such Companies to the extent based on a claim
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation that any Product made to Buyer specifications infringed intellectual property
unless Buyer indemnifies Omron against all related costs or expenses. rights of another party.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery 16. Property; Confidentiality. Any intellectual property in the Products is the exclu-
resulting from causes beyond its control, including earthquakes, fires, floods, sive property of Omron Companies and Buyer shall not attempt to duplicate it
strikes or other labor disputes, shortage of labor or materials, accidents to in any way without the written permission of Omron. Notwithstanding any
machinery, acts of sabotage, riots, delay in or lack of transportation or the charges to Buyer for engineering or tooling, all engineering and tooling shall
requirements of any government authority. remain the exclusive property of Omron. All information and materials supplied
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron: by Omron to Buyer relating to the Products are confidential and proprietary,
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship and Buyer shall limit distribution thereof to its trusted employees and strictly
except in “break down” situations. prevent disclosure to any third party.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall 17. Export Controls. Buyer shall comply with all applicable laws, regulations and
constitute delivery to Buyer; licenses regarding (i) export of products or information; (iii) sale of products to
c. All sales and shipments of Products shall be FOB shipping point (unless oth- “forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
erwise stated in writing by Omron), at which point title and risk of loss shall regulated technology or information.
pass from Omron to Buyer; provided that Omron shall retain a security inter- 18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
est in the Products until the full purchase price is paid; and no course of dealing between Buyer and Omron shall operate as a waiver
d. Delivery and shipping dates are estimates only; and of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
e. Omron will package Products as it deems proper for protection against nor- without Omron's written consent. (c) Law. These Terms are governed by the
mal handling and extra charges apply to special conditions. law of the jurisdiction of the home office of the Omron company from which
12. Claims. Any claim by Buyer against Omron for shortage or damage to the Buyer is purchasing the Products (without regard to conflict of law princi-
Products occurring before delivery to the carrier must be presented in writing ples). (d) Amendment. These Terms constitute the entire agreement between
to Omron within 30 days of receipt of shipment and include the original trans- Buyer and Omron relating to the Products, and no provision may be changed
portation bill signed by the carrier noting that the carrier received the Products or waived unless in writing signed by the parties. (e) Severability. If any provi-
from Omron in the condition claimed. sion hereof is rendered ineffective or invalid, such provision shall not invalidate
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
Products will be free from defects in materials and workmanship for a period of against the amount owing in respect of this invoice. (g) Definitions. As used
twelve months from the date of sale by Omron (or such other period expressed herein, “including” means “including without limitation”; and “Omron Compa-
in writing by Omron). Omron disclaims all other warranties, express or implied. nies” (or similar words) mean Omron Corporation and any direct or indirect
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, subsidiary or affiliate thereof.
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-

Certain Precautions on Specifications and Use

1. Suitability of Use. Omron Companies shall not be responsible for conformity ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-
with any standards, codes or regulations which apply to the combination of the ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
Product in the Buyer’s application or use of the Product. At Buyer’s request, OVERALL EQUIPMENT OR SYSTEM.
Omron will provide applicable third party certification documents identifying 2. Programmable Products. Omron Companies shall not be responsible for the
ratings and limitations of use which apply to the Product. This information by user’s programming of a programmable Product, or any consequence thereof.
itself is not sufficient for a complete determination of the suitability of the Prod- 3. Performance Data. Data presented in Omron Company websites, catalogs
uct in combination with the end product, machine, system, or other application and other materials is provided as a guide for the user in determining suitabil-
or use. Buyer shall be solely responsible for determining appropriateness of ity and does not constitute a warranty. It may represent the result of Omron’s
the particular Product with respect to Buyer’s application, product or system. test conditions, and the user must correlate it to actual application require-
Buyer shall take application responsibility in all cases but the following is a ments. Actual performance is subject to the Omron’s Warranty and Limitations
non-exhaustive list of applications for which particular attention must be given: of Liability.
(i) Outdoor use, uses involving potential chemical contamination or electrical 4. Change in Specifications. Product specifications and accessories may be
interference, or conditions or uses not described in this document. changed at any time based on improvements and other reasons. It is our prac-
(ii) Use in consumer products or any use in significant quantities. tice to change part numbers when published ratings or features are changed,
(iii) Energy control systems, combustion systems, railroad systems, aviation or when significant construction changes are made. However, some specifica-
systems, medical equipment, amusement machines, vehicles, safety equip- tions of the Product may be changed without any notice. When in doubt, spe-
ment, and installations subject to separate industry or government regulations. cial part numbers may be assigned to fix or establish key specifications for
(iv) Systems, machines and equipment that could present a risk to life or prop- your application. Please consult with your Omron’s representative at any time
erty. Please know and observe all prohibitions of use applicable to this Prod- to confirm actual specifications of purchased Product.
uct. 5. Errors and Omissions. Information presented by Omron Companies has been
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS checked and is believed to be accurate; however, no responsibility is assumed
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT for clerical, typographical or proofreading errors or omissions.
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
OMRON AUTOMATION AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com

OMRON CANADA, INC. • HEAD OFFICE OMRON ARGENTINA • SALES OFFICE

Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com Cono Sur • 54.11.4783.5300

OMRON ELECTRONICS DE MEXICO • HEAD OFFICE OMRON CHILE • SALES OFFICE

México DF • 52.55.59.01.43.00 • 01-800-226-6766 • [email protected] Santiago • 56.9.9917.3920

OMRON ELECTRONICS DE MEXICO • SALES OFFICE OTHER OMRON LATIN AMERICA SALES
Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • [email protected] 54.11.4783.5300

OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE

São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br

OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu

Authorized Distributor: Controllers & I/O

• Machine Automation Controllers (MAC) • Motion Controllers
• Programmable Logic Controllers (PLC) • Temperature Controllers • Remote I/O
Robotics
• Industrial Robots • Mobile Robots
Operator Interfaces
• Human Machine Interface (HMI)
Motion & Drives
• Machine Automation Controllers (MAC) • Motion Controllers • Servo Systems
• Frequency Inverters
Vision, Measurement & Identification
• Vision Sensors & Systems • Measurement Sensors • Auto Identification Systems
Sensing
• Photoelectric Sensors • Fiber-Optic Sensors • Proximity Sensors
• Rotary Encoders • Ultrasonic Sensors
Safety
• Safety Light Curtains • Safety Laser Scanners • Programmable Safety Systems
• Safety Mats and Edges • Safety Door Switches • Emergency Stop Devices
• Safety Switches & Operator Controls • Safety Monitoring/Force-guided Relays
Control Components
• Power Supplies • Timers • Counters • Programmable Relays
• Digital Panel Meters • Monitoring Products
Switches & Relays
• Limit Switches • Pushbutton Switches • Electromechanical Relays
• Solid State Relays
Software
• Programming & Configuration • Runtime

E84I-E-01 06/16 Note: Specifications are subject to change. © 2016 Omron. All Rights Reserved. Printed in U.S.A.

Printed on recycled paper.